NTI AG / LinMot Dok-Nr. 0185-0099-E_1V1_IG_Linear_Motors_P10-54
Installation Guide
Linear Motors
ENG
P10-54 / P10-54-D24/25/25S
Installation Guide Linear Motors ENG
Page 2 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
Content
1 General information ................................................................................................................................. 4
1.1 Introduction ........................................................................................................................................ 4
1.2 Explanation of symbols ...................................................................................................................... 4
1.3 Qualified personnel ............................................................................................................................ 4
1.4 Liability ............................................................................................................................................... 4
1.5 Copyright............................................................................................................................................ 4
2 Safety instructions ................................................................................................................................... 5
3 Installation instructions ........................................................................................................................... 7
3.1 Operating conditions .......................................................................................................................... 7
3.2 Instructions for installing the linear motor .......................................................................................... 7
3.3 Mounting the stator ............................................................................................................................ 8
3.4 Mounting the payload to the slider ..................................................................................................... 8
3.5 "Moving slider" installation ............................................................................................................... 10
3.6 "Moving stator" installation ............................................................................................................... 10
3.6.1 Assembling instruction ................................................................................................................. 11
3.7 Minimum distance from slider .......................................................................................................... 13
3.7.1 Minimum distance from slider to slider ........................................................................................ 13
3.7.2 Minimum distance from slider to metallic parts ............................................................................ 13
4 Motor Cable ............................................................................................................................................. 14
4.1 Technical Data ................................................................................................................................. 14
4.2 Options of power cable .................................................................................................................... 15
4.2.1 Stator Series P10-54 ................................................................................................................... 15
4.2.2 Stator Series P10-54-D2x ............................................................................................................ 15
4.3 Options of sensor cables ................................................................................................................. 15
4.3.1 Stator Series P10-54 ................................................................................................................... 15
4.3.2 Stator Series P10-54-D2x ............................................................................................................ 15
4.4 Attaching the cable shielding .......................................................................................................... 16
4.5 Rotatability of motor connectors ...................................................................................................... 16
5 Accessories ............................................................................................................................................ 17
5.1 Bearing kit ........................................................................................................................................ 17
5.1.1 Overview ...................................................................................................................................... 17
5.1.2 Mounting ...................................................................................................................................... 18
5.2 Mounting flanges ............................................................................................................................. 19
5.3 Fan kits for flanges .......................................................................................................................... 21
5.4 Slider mounting kits ......................................................................................................................... 21
5.4.1 Fixed bearing ............................................................................................................................... 21
5.4.2 Floating bearing ........................................................................................................................... 22
5.4.3 Complete mounting kit ................................................................................................................. 22
6 Maintenance and test instructions ....................................................................................................... 23
6.1 Stator connector assignment ........................................................................................................... 23
6.1.1 Power Connector ......................................................................................................................... 23
6.1.2 Sensor Connector ........................................................................................................................ 24
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 3 / 32
6.2 Stator checking ................................................................................................................................ 25
6.3 Maintenance of linear motors .......................................................................................................... 26
6.3.1 Mounting ...................................................................................................................................... 26
6.3.2 Inspection ..................................................................................................................................... 26
6.3.3 Cleaning ....................................................................................................................................... 26
6.3.4 Cleaning agent / Lubricant ........................................................................................................... 26
7 Storage, transport, installation altitude ............................................................................................... 27
8 Dimensions ............................................................................................................................................. 27
8.1 Stator ............................................................................................................................................... 27
8.1.1 PS10-54x120 ............................................................................................................................... 27
8.1.2 PS10-54x180 ............................................................................................................................... 27
8.1.3 PS10-54x240 ............................................................................................................................... 28
8.1.4 PS10-54x300 ............................................................................................................................... 28
8.2 Slider ................................................................................................................................................ 28
9 UL Certificate .......................................................................................................................................... 29
10 Declaration of Conformity and CE-marking .................................................................................... 31
Installation Guide Linear Motors ENG
Page 4 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
1 General information
1.1 Introduction
This manual includes instructions for the assembly, installation, maintenance, transport, and storage of linear
motors. The document is intended for electricians, mechanics, service technicians, and warehouse staff.
Be sure to observe the general safety instructions as well as those in each chapter at all times.
Keep this manual accessible to the assigned staff.
1.2 Explanation of symbols
Triangular warning symbols warn against a danger.
Round command symbols tell what to do.
1.3 Qualified personnel
All work such as transport, installation, commissioning and service is only allowed to be carried out by
qualified personnel. Qualified personnel in the sense of the safety instructions in this documentation are
persons who are familiar with the transport, installation, assembly, commissioning and operation of the
product and who have the appropriate qualifications.
This manual must be read carefully before transport, installation, commissioning, service and all safetyrelated information must be adhered to.
1.4 Liability
NTI AG (as manufacturer of LinMot linear motors and MagSpring products) excludes all liability for damages
and expenses caused by incorrect use of the products. This also applies to false applications, which are
caused by NTI AG's own data and notes, for example in the course of sales, support or application activities.
It is the sole responsibility of the user to check the information and information provided by NTI AG regarding
their safety-relevant correctness. In addition, the entire responsibility for safety-related product functionality
lies exclusively with the user.Product warranties are void if products are used with stators, sliders, servo
drives or cables not manufactured by NTI AG unless such use was specifically approved by NTI AG.
NTI AG’s warranty is limited to repair or replacement as stated in our standard warranty policy as described
in our "terms and conditions" previously supplied to the purchaser of our equipment (please request copy of
same if not otherwise available). Further reference is made to our general terms and conditions.
1.5 Copyright
This work is protected by copyright.
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or
mechanical, including photocopying, recording, microfilm, storing in an information retrieval system, not even
for training purposes, or translating, in whole or in part, without the prior written consent of NTI AG.
LinMot® is a registered trademark of NTI AG.
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 5 / 32
2 Safety instructions
Contusions
Sliders contain neodynium magnets and have a strong attractive force.
Careless handling could cause fingers or skin to become pinched between two sliders.
This may lead to contusions, bruises, and bone fractures.
When handling sliders, wear thick protective gloves and keep a minimum distance between
sliders. Refer to the "Minimum distance from slider" section for minimum distance.
To reduce the risk of injury, never more than one slider should be held or transported by the
same person without packaging.
Pacemaker / Implanted heart defibrillator
Sliders could affect the functioning of pacemakers and implanted heart defibrillators. For the
duration of a strong approach to a magnetic field, these devices switch into test mode and
will not function properly.
• If you wear one of those devices keep the following minimum distances between the
pacemaker / defibrillator and slider:
- Min. 250 mm (10ʺ) for slider Ø 27 mm and 28 mm (PL01-27 / 28 / PL10-28)
- Min. 150 mm (6ʺ) for slider Ø 19 mm and 20 mm (PL01-19 / 20)
- Min. 100 mm (4ʺ) for slider Ø 12 mm (PL01-12)
• Inform others who wear these devices to comply with these minimum distances!
Caution - Risk of Electric Shock !
Before working, make sure that there are no high voltages.
Fast-moving machine parts
The sliders of LinMot linear motors are fast-moving machine parts. All necessary
precautions must be taken to prevent access during operation (provide covers, guards,
etc.).
Automatic restart
The motors can start automatically under certain cricumstances!
If necessary, a corresponding warning symbol must be provided and protection against
entering the hazardous area or a suitable safe electronic disconnection must be provided!
Risk of injury due to a defect or fault
For areas where a defect or fault can result in substantial property damage or even serious
personal injury, additional external precautions must be taken or devices must be installed
to ensure safe operation even if a defect or fault occurs (eg. suitable safe electronic
disconnection, mechanical interlocks, barriers, etc.).
Magnetic field
Magnets integrated in the sliders produce a strong magnetic field. They could damage TVs,
laptops, computer hard drives, credit and ATM cards, data storage media, mechanical
watches, hearing aids, and speakers.
• Keep magnets away from devices and objects that could be damaged by strong
magnetic fields.
• For the above mentioned objects, keep a minimum distance as described in the
"Pacemaker / implanted defibrillator" section.
• For non-anti-magnetic watches, keep the double minimum distance.
Installation Guide Linear Motors ENG
Page 6 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
Combustibility
When machining magnets, the drilling dust could easily ignite.
Machining the sliders and the magnets they contain is not permitted.
Burn hazard
The sliders of LinMot motors can reach temperatures of 80 °C, which may cause burns
upon contact.
Grounding
All metal parts that are exposed to contact during any user operation or servicing and likely
to become energized shall be reliably connected to the means for grounding.
Mechanical handling
Neodymium magnets are brittle and heat-sensitive.
Machining the sliders and the magnets they contain is not permitted.
• Colliding magnets could crack. Sharp splinters could be catapulted for several meters
and cause eye injury.
• By machining the sliders, heat would result which demagnetises the magnets.
Slider
Linear motor sliders consist of a high-precision, thin-walled stainless steel tube in which the
neodymium magnets are housed. The LinMot sliders should be handled with care.
Avoid contact with other sliders or iron parts as this can damage the magnets and the slider
surface. Do not grip the sliders with pliers, as this can also damage the surface. Do not use
sliders which are already damaged on the surface (scratches, deformation, etc.). This can
cause further damage to the stator.
Effects on people
According to the current level of knowledge, magnetic fields of permanent magnets do not
have a measurable positive or negative effect on people. It is unlikely that permanent
magnets constitute a health risk, but it cannot be ruled out entirely.
• For your own safety, avoid constant contact with magnets.
• Store large magnets at least one meter away from your body.
Temperature resistance
Keep slider away from unshielded flame or heat.
Temperature above 120°C will cause demagnetization.
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 7 / 32
3 Installation instructions
3.1 Operating conditions
Maximum ambient temperature limits:
• 10 °C…80 °C
Internal temperature sensor error occurs at:
• 90 °C
3.2 Instructions for installing the linear motor
Please attend to the safety instructions in chapter 2 during the assembling!
For maintenance purposes, please observe the installation instructions in chapter 6.
1. Clean the slider with a paper towel.
2. Lubrication of the slider
Sliders with a length ≤ 500 mm are inserted
without lubrication.
Sliders with a length > 500 mm are
lubricated with a grease amount of 4 g
(0.14 oz) per meter, which is is about ½ of
a hazel-nut.
3. Insert the slider in the defined direction
(see Assembly step 4.).
Attention! The slider is magnetically
attracted.
Installation Guide Linear Motors ENG
Page 8 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
Slider back end:
M10 thread
Slider front end:
M10 thread + cut-in
4. Checking the installed direction of slider
After the installation, the front end of the
slider with M 10 thread and cut-in is located
at the opposite side of the stator from the
cable exit.
3.3 Mounting the stator
The stator is mounted by clamping. The LinMot flange (see the section 5 « Accessories ») or a similar flange
can be used for this purpose. Most important is a broad clamping surface in order to provide good heat
dissipation. Additionally, the cooling can be increased by a fan or liquid (water cooling), so that the
continuous power is significantly improved.
The flange clamp must not deform the stator.
Do not exceed max. torque of 12 Nm.
Incorrect mounting
Small contact area prevents cooling of the linear
motor.
Correct mounting
Better heat dissipation with the LinMot flange.
Correct mounting
Forced air cooling with LinMot fan to increase the
continuous force.
3.4 Mounting the payload to the slider
The load is mounted as a fixed bearing using spherical washers and conical seats (see the section 5).
• To avoid shear force on slider and wear on stator, the payload has to be beared by a
linear guide.
• Slider back end should not be used for load mounting.
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 9 / 32
Slider back end (M10 thread) Slider front end (M10 thread)
When attaching the load, the wrench for tightening the load must be used only on the loadfacing side of the slider. Avoid torsional stress on slider (note the following figures).
Incorrect mounting
Torsional stress on slider!
Correct mounting
Slider
Thread
Max. torque for screw
(Dry)
28 mm
M 10
42 Nm
Installation Guide Linear Motors ENG
Page 10 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
3.5 "Moving slider" installation
In a "moving slider" installation, the stator is fixed and the slider is the moving part.
The load, borne by a linear guide, is attached directly to the end of the slider. In order to compensate for
misalignment, spherical axial bearings consisting of spherical washers and conical seats (see the section
Slider mounting kits) are used to connect to the load. The mounting kit of slider and an oversized hole for the
screw make it possible to adjust a radial and angle offset.
Mounted payload with radial and angle offset.
3.6 "Moving stator" installation
In "moving stator" applications, the slider is fixed and the stator is the moving part.
The load is attached to the stator, which is mounted on a linear guide. In order to avoid an overconstrained
bearing mount and compensate for alignment errors, the slider may be mounted on one end in a fixed
bearing with a spherical axial bearing. On the opposite end, the slider is mounted in a floating bearing.
Mounting kits are available for mounting the slider (see the section Slider mounting kits).
Stator
Floating bearing
Slider front end
Spherical washer and
conical seat
Slider back end
Linear bearing
Linear guide
Stator
Slider
Spherical washer +
conical seat
Slider
back end
Linear bearing
Linear guide
Slider front end
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 11 / 32
3.6.1 Assembling instruction
Please attend to the safety instructions in chapter 2 during the assembling!
If moving stator application is used, the minimum bending radius of the motor cable should
be adhered to. See chapter Cable, section Technical Data.
1. Mount stator to its support bearing.
2. Placing a spacer
Put a spacer (wood, plasic, aluminium with
thickness 15 mm) between slider and linear
guide. The spacer prevents injuries to the
hands and damage to the slider surface!
3. Insert slider into stator.
Installation Guide Linear Motors ENG
Page 12 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
4. Installing the slider using the fixed
bearing
The fixed bearing is screwed to the front
end of the slider.
Important! Do not tighten the screw yet!
5. Mount floating bearing
Imortant!
Do not tighten the screw!
The slider is allowed to extend into the
floating bearing no more than 15 mm!
6. Move stator (back end) to the fixed end
of slider, center slider in stator and
tighten the screw.
7. Move stator (front side) to the floating
bearing and tighten screws.
After the installation of the slider a safety label must be placed close to the slider.
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 13 / 32
3.7 Minimum distance from slider
3.7.1 Minimum distance from slider to slider
The sliders are made of neodymium magnets and have a strong magnetic attraction.
It must be kept a minimum distance between the sliders. This minimized the risk of bruising and secondly,
the sliders do not influence each other through their magnetic fields.
Type of slider
PL01
PL01-20 / PL01-19
PL01-28 / PL01-27
PL10-28
PL01-12
30 mm (1.18 in)
PL01-20 / PL01-19
50 mm (1.97 in)
PL01-28 / PL01-27
80 mm (3.15 in)
PL10-28
70 mm (2.76 in)
The data are measured from slider center to slider center.
3.7.2 Minimum distance from slider to metallic parts
When installing linear motors in modules with metal parts near the slider, undesired forces can arise due to
magnetic attraction or eddy currents. These generally manifest as erratic and jerky positioning, or reduced
dynamics of the linear motor. In order to avoid this, minimum distances between the slider and any metal
parts are to be observed whenever metal materials are used nearby.
Linear
Motor
Minimum distance from slider surface
to ferromagnetic parts (iron, steel,
etc.)
Minimum distance from slider surface to
non-ferromagnetic metallic parts
(aluminum, bronze, stainless steel, etc.)
P10-54x…
20 mm
10 mm
Installation Guide Linear Motors ENG
Page 14 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
4 Motor Cable
Do not connect or disconnect motor when there is power on the servo drive.
Use only original LinMot cable. Cables from other sources must be checked precisely
before commissioning.
Incorrect connections can destroy the drive and stator.
4.1 Technical Data
The motor series P10-54 use various types of cables, which are used for power supply and signal power. All
cables are high-flex cables (suitable for trailing chains) and are used for fixed and moving applications.
Power cable
Sensor cable
Type
KPS07-04/02
KSS05-02/08
KSS05-02/13
Used for
PS10-54
PS10-54-D2x
PS10-54
PS10-54-D2x
Minimum bending
radius for fixed
installation
70 mm
(2.76 in)
45 mm
(1.75)
45 mm
(1.75)
Minimum bending
radius when moving
140 mm
(5.52 in)
No torsion
90 mm
(3.54 in)
No torsion
90 mm
(3.54 in)
No torsion
Max. Cable length
30 m (may be limited by Servo Drive)
Approval
UL / CSA 1000V / 300V
UL / CSA 300V
UL / CSA 300V
Material
Wire isolation: PES
Jacket: PUR
Wire isolation: TPE
Jacket: Special TPU
Wire isolation: PE
Jacket: PUR
Oil resistance
very good
very good
very good
Chemical resistance
(to acids, alkalis,
solvents, hydraulic
fluid)
good
good
good
Outdoor durability
very good
very good
very good
Flammability
flame retardant
flame retardant
flame retardant
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 15 / 32
4.2 Options of power cable
4.2.1 Stator Series P10-54
Item
Description
Item-No.
KPS07-04/02-L/Tk-3
Power Trailing Chain Cable E1400/P10-54, 3 m
0150-2670
KPS07-04/02-L/Tk-5
Power Trailing Chain Cable E1400/P10-54, 5 m
0150-2671
KPS07-04/02-L/Tk-8
Power Trailing Chain Cable E1400/P10-54, 8 m
0150-2672
KPS07-04/02-L/Tk-12
Power Trailing Chain Cable E1400/P10-54, 12 m
0150-2673
KPS07-04/02-B/Tk-3
Power Trailing Chain Cable C1400/P10-54, 3 m
0150-3648
KPS07-04/02-B/Tk-5
Power Trailing Chain Cable C1400/P10-54, 5 m
0150-3657
KPS07-04/02-B/Tk-8
Power Trailing Chain Cable C1400/P10-54, 8 m
0150-3658
KPS07-04/02-B/Tk-12
Power Trailing Chain Cable C1400/P10-54, 12 m
0150-3659
4.2.2 Stator Series P10-54-D2x
Item
Description
Item-No.
KPS07-04/02-./Tk-10
Power Trailing Chain Cable .../Tk, 10 m
0150-3626
KPS07-04/02-./Tk-
Power Trailing Chain Cable .../Tk, Custom length
0150-3622
4.3 Options of sensor cables
4.3.1 Stator Series P10-54
Item
Description
Item-No.
KSS 05-02/08-D15s/Uk-3
Encoder Trailing Chain Cable D15s/Uk, 3 m
0150-2650
KSS 05-02/08-D15s/Uk-5
Encoder Trailing Chain Cable D15s/Uk, 5 m
0150-2651
KSS 05-02/08-D15s/Uk-8
Encoder Trailing Chain Cable D15s/Uk, 8 m
0150-2652
KSS 05-02/08-D15s/Uk-12
Encoder Trailing Chain Cable D15s/Uk, 12 m
0150-2653
4.3.2 Stator Series P10-54-D2x
Item
Description
Item-No.
KSS 05-02/13-./Uk-10
Encoder Trailing Chain Cable ./Uk, 10 m
0150-3627
KSS 05-02/13-./Uk-
Encoder Trailing Chain Cable ./Uk, Custom length
0150-3619
Installation Guide Linear Motors ENG
Page 16 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
4.4 Attaching the cable shielding
The power cable is supplied with a copper shielding (see illustration above). This prevents electrical and / or
magnetic fields. The shielded part of the cable must be grounded via a connection to the back wall of the
switchboard. The shielding has to be mounted holohedral to the connection part (see scheme above). The
shield connection terminal block is offered as an accessory for power cables and must be ordered separately
(Item-No. 0150-3631) However, the kind of attaching the cable shielding generally depends on the system of
the switchboard manufacturer.
4.5 Rotatability of motor connectors
The motor connector can be rotated in both directions. (see illustration below).
Power Cable
Shrink tubing
Copper shielding
L-Connector (6 pin)
Power Cable
Conductive
mounting plate
Shield connect.
terminal block
Servo Drive
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 17 / 32
5 Accessories
5.1 Bearing kit
The stators are equipped with a removable bearing set as standard. This consists of 1 or 2 removable
bearing bushings and 2 end pieces with wipers. By the use of the wipers maintenance and the maintenance
cycles can be extended. It also effects that the lubricant is dispensed metered and does not leak outside of
the stator. The lubricant is less dirty.
5.1.1 Overview
Pos. 1: Pan head screw stainless steel; Pos. 2: Stator end piece; Pos. 3: Wiper; Pos. 4: Bearing bushing
Ordering information
Item
Description
Item-No.
PB10-54x120-L
Bearing kit for PS10-54x120
0150-3671
PB10-54x180-L
Bearing kit for PS10-54x180
0150-3672
PB10-54x240-L
Bearing kit for PS10-54x240
0150-3673
PB10-54x300-L
Bearing kit for PS10-54x300
0150-3674
Installation Guide Linear Motors ENG
Page 18 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
5.1.2 Mounting
1. Dismounting front bearing set
Remove the end piece and the bearing
bushing at the front end of the stator.
Note! With the stator P10-54x120 there is
only 1 bearing bushing for the whole length.
2. Mounting front bearing set
The bearing bushing is pushed in as far as
it will go. Then screw the end piece
together with the 2 pan-head screws.
Tightening torque: 1.2 Nm
The pan-head screws are already coated
with Tuflok.
3. Dismounting rear bearing set
Remove the end piece and the bearing
bushing at the front end of the stator.
Note! With the stator P10-54x120 there is
only 1 bearing bushing for the whole length.
4. Mounting rear bearing set
The bearing bushing is pushed in as far as
it will go. Then screw the end piece
together with the 2 pan-head screws.
Tightening torque: 1.2 Nm
The pan-head screws are already coated
with Tuflok.
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 19 / 32
5.2 Mounting flanges
Max. Torque
Screws: 12 Nm
(8.85 lbf ft)
Fan Number
Standard: 1
Maximum: 1
Item
Description
Weight [g]
Item-No.
PF10-54x140
Flange for PS10-54x120
781
0150-2733
Max. Torque
Screws: 12 Nm
(8.85 lbf ft)
Fan Number
Standard: 1
Maximum: 1
Item
Description
Weight [g]
Item-No.
PF10-54x200
Flange for PS10-54x180
1132
0150-2734
T-Slot 6 mm M4 /
T-Slot 6 mm M4 /
Installation Guide Linear Motors ENG
Page 20 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
Max. Torque
Screws: 12 Nm (8.85 lbf ft)
Fan Number
Standard: 1
Maximum: 2
Item
Description
Weight [g]
Item-No.
PF10-54x260
Flange for PS10-54x240
1475
0150-2735
Max. Torque
Screws: 12 Nm (8.85 lbf ft)
Fan Number
Standard: 2
Maximum: 2
Item
Description
Weight [g]
Item-No.
PF10-54x320
Flange for PS10-54x300
1809
0150-2736
T-Slot 6 mm M4 /
T-Slot 6 mm M4 /
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 21 / 32
5.3 Fan kits for flanges
Power Supply
Fan
24 VDC, 120 mA
Air flow
80 m3 / h
Item
Description
Item-No.
HV01-37 / 48
Fan Kit for H01-37 / 48 and PF02-37 / 48 composed of:
1 x Fan, 4 x cylinder screw M4 x 30, 4 x square nut M4,
4 x spacer M4 x 16
0150-5051
5.4 Slider mounting kits
5.4.1 Fixed bearing
Slider mounting kit consists of a spring washer, a pair of spherical
washers, and a pair of conical seats. It allows the slider to be fixed
in the direction of motion. It also helps to compensate for radial and
angle offset.
Material
Spherical washer / conical seat: case hardened steel
Item
Item No.
Slider
Thread
d1
d2
d3
h
PLF01-28
0150-3087
28mm
M10
10.5mm
(0.41in)
12mm
(0.47in)
21mm
(0.83in)
6.5mm
(0.26in)
Installation Guide Linear Motors ENG
Page 22 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
PLF01-28
(Stainless-st.)
0150-3297
28mm
M10
10.5mm
(0.41in)
12mm
(0.47in)
21mm
(0.83in)
6.5mm
(0.26in)
5.4.2 Floating bearing
Floating bearing assembly that permits radial adjustment of slider
position and permits a small amount of radial and axial movement.
Material
Housing: Stainless steel 1.4305
Bearing: Nitrile butadiene rubber
Spring steel DIN17223
Item
Item No.
Slider
Thread
d1
d2
d3
D4
L
PLL01-28
0150-3094
28mm
M5
28mm
(1.10in)
32mm
(1.26in)
40mm
(1.57in)
48mm
(1.89in)
20mm
(0.79in)
5.4.3 Complete mounting kit
This kit provides one set of mounting parts for each end of the
slider.
Ordering information
Item
Description
Item-No.
PLM01-28-MK
Mounting kit for PL01-28 slider composed of:
1 Spherical washer & conical seat (0150-3087)
1 Floating Bearing (0150-3094)
1 Socket hd. cap screw * DIN 912 / M10, L=35 mm (L=1.38 in)
4 Socket hd. cap screw * DIN 912 / M5, L=20 mm (L=0.78 in)
0150-3095
* For use with 12 mm (1/2 in) thick mounting plates.
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 23 / 32
6 Maintenance and test instructions
6.1 Stator connector assignment
Do not connect or disconnect motor when there is power on the servo drive.
Use only original LinMot cable. Cables from other sources must be checked precisely
before commissioning.
Incorrect connections can destroy the drive and stator.
6.1.1 Power Connector
View: Motor connector, plug side
Pin
PS10-54
PS10-54-D24
PS10-54-D25
PS10-54-D25S
Wire color
Motor cable
A
Phase U
Phase U
Phase U
red
PE
PE
PE
PE
yellow-green
B
Phase V
Phase V
Phase V
blue
C
Phase W
Phase W
Phase W
black
(previously: green)
1
n. c.
Pt1000+
PTC+
turquoise
2
n. c.
Pt1000-
PTC-
grey
3
n. c.
n. c.
n. c.
n. c.
4
n. c.
n. c.
n. c.
n. c.
5
n. c.
n. c.
n. c.
n. c.
Installation Guide Linear Motors ENG
Page 24 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
6.1.2 Sensor Connector
View: Motor connector, plug side
Pin
PS10-54
Wire color
Motor cable
1
+Vcc
red 2 GND
black
3
Sin+
yellow
4
Sin-
orange
5
Cos+
green
6
Cos-
blue
7
Mot. Link C+
pink
8
Mot. Link C-
grey
9 - 12
n. c.
n. c.
A / B / C
n. c.
n. c.
Pin
PS10-54-D24
PS10-54-D25
PS10-54-D25S
Wire color
Motor cable
1
+Vcc
+Vcc
white
2
GND
GND
brown
3 A A
grey
4
/ A
/ A
pink
5 B B
blue
6
/ B
/ B
red 7 – – green (do not connect)
8 – –
yellow (do not connect)
9
Pt1000+ *
PTC+ *
yellow-brown
10
Pt1000- *
PTC- *
white-yellow
11
REF+
REF+
black
12
REF-
REF-
purple
A
Hall U
Hall U
grey-red
B
Hall V
Hall V
red-blue
C
Hall W
Hall W
white-green
* Temperature Feedback
The resistance of the temperature sensor is emulated and only correctly reproduces the
temperature when the sensor power supply is active. The connection potentials of the
temperature resistance must lie within a range of 0-16V with respect to the sensor GND.
The encoder must have been powered on for at least 50 ms, before valid temperatures can
be measured. If the encoder is powered off, 20k Ohms are measured between Pins 9 and
10.
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 25 / 32
6.2 Stator checking
The following tables show the resistive value between the different connector pins for each stator type. If the
value is not within a range of +/- 10% the stator may be damaged (temperature of the stator for all
measurements: 25°C).
PS10-54x120U-BL-TU (0150-2722) PS10-54x120U-BL-TU-D25 (0150-2752)
PS10-54x120U-BL-TU-D24 (0150-2748) PS10-54x120U-BL-TU-D25S (0150-2782)
Phase U / Phase V
Pin A / Pin B
14 @ 25 °C
Phase V / Phase W
Pin B / Pin C
14 @ 25 °C
Phase W / Phase U
Pin C / Pin A
14 @ 25 °C
Casing
Any phases / Casing
> 200 M @ 25 °C
Pt1000+ / Pt1000-
(only series D24)
Pin 1 / Pin 2
20 ± 0.2 k @ 25 °C
PTC+ / PTC-
(only series D25 / D25S)
Pin 1 / Pin 2
20 ± 0.2 k @ 25 °C
PS10-54x180U-BL-TU (0150-2723) PS10-54x180U-BL-TU-D25 (0150-2753)
PS10-54x180U-BL-TU-D24 (0150-2749) PS10-54x180U-BL-TU-D25S (0150-2783)
Phase U / Phase V
Pin A / Pin B
5.7 @ 25 °C
Phase V / Phase W
Pin B / Pin C
5.7 @ 25 °C
Phase W / Phase U
Pin C / Pin A
5.7 @ 25 °C
Casing
Any phases / Casing
> 200 M @ 25 °C
Pt1000+ / Pt1000-
(only series D24)
Pin 1 / Pin 2
20 ± 0.2 k @ 25 °C
PTC+ / PTC-
(only series D25 / D25S)
Pin 1 / Pin 2
20 ± 0.2 k @ 25 °C
PS10-54x240U-BL-TU (0150-2724) PS10-54x240U-BL-TU-D25 (0150-2754)
PS10-54x240U-BL-TU-D24 (0150-2750) PS10-54x240U-BL-TU-D25S (0150-2784)
Phase U / Phase V
Pin A / Pin B
7.5 @ 25 °C
Phase V / Phase W
Pin B / Pin C
7.5 @ 25 °C
Phase W / Phase U
Pin C / Pin A
7.5 @ 25 °C
Casing
Any phases / Casing
> 200 M @ 25 °C
Pt1000+ / Pt1000-
(only series D24)
Pin 1 / Pin 2
20 ± 0.2 k @ 25 °C
PTC+ / PTC-
(only series D25 / D25S)
Pin 1 / Pin 2
20 ± 0.2 k @ 25 °C
PS10-54x300U-BL-TU (0150-2725) PS10-54x300U-BL-TU-D25 (0150-2755)
PS10-54x300U-BL-TU-D24 (0150-2751) PS10-54x300U-BL-TU-D25S (0150-2785)
Phase U / Phase V
Pin A / Pin B
5.7 @ 25 °C
Phase V / Phase W
Pin B / Pin C
5.7 @ 25 °C
Phase W / Phase U
Pin C / Pin A
5.7 @ 25 °C
Casing
Any phases / Casing
> 200 M @ 25 °C
Pt1000+ / Pt1000-
(only series D24)
Pin 1 / Pin 2
20 ± 0.2 k @ 25 °C
PTC+ / PTC-
(only series D25 / D25S)
Pin 1 / Pin 2
20 ± 0.2 k @ 25 °C
* Temperature resistances can only be correctly set with active sensor power supply.
(emulated temperature resistance).
Installation Guide Linear Motors ENG
Page 26 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
6.3 Maintenance of linear motors
The stators will be shipped with an initial lubrication. Maintenance will only be required if the motors run 'dry'
or there is a heavy pollution of the motors.Under normal industrial conditions (5 day, 8 h / day) one inspection
every 3 months is adequate. The inspection cycle must be shortened if severe motor loads or deviating
conditions exist. These conditions are for example:
• Permanent fouling
• Direct sunshine
• Low Humidity
• Outdoor operation
• Increased operating temperature
6.3.1 Mounting
Sliders with a length ≤ 500 mm (20 in) are to be inserted in a clean contition in the stator.
Sliders with a length > 500 mm (20 in) must be lubricated with LU02. 4 g of lubricant per meter slider is
enough to create a film of lubricant on the surface of the sliders. 4 g (0.14 oz) is about ½ of a hazel-nut.
The grease can be applied by hand or with a soft paper towel.
If wipers are used then the inner side of the seals of the wipers must be lubricated as well.
Basically, it must be ensured that only a thin film of grease is applied. 4 g of grease per
1000 mm of slider length is sufficient for this purpose. Over lubrication leads to a gumming
of the grease, which appears particularly at higher operating temperatures! In this case, a
complete cleaning of the motor has to be made.
6.3.2 Inspection
Inspections have to be executed according to the operating condition and the load of motors. Following
points have to be checked during inspection:
a) Is a film of lubricant on the slider? If not -> Lubrication
b) Is the wiper (if existent) without visible wear? If not -> Replace wipers
c) Is the lubricant homogeneous and not decomposed? In case of negation -> Cleaning (stator, slider) +
Lubrication
d) Can the slider be moved easily? If not -> Cleaning (stator, slider) + Lubrication
6.3.3 Cleaning
• Pull the sliders carefully out of the stator.
Attention! Strong magnetic attraction forces (note safety instructions on page 5)!
Use non magnetic material (e.g. wood) to cover close-by iron constructions.
• Clean slider and stator with a soft disposable paper, ideally with the help of LU06 cleaning spray (or
methylated spirits or alcohol).
• Afterwards, lubricate the bore of the stators with about 2-3 g (0.1 oz) grease LU02.
There should only be a slight film of lubricant.
Note: Do not over lubricate!
• Finally, slider should be lubricated according to the chapter 'mounting'.
6.3.4 Cleaning agent / Lubricant
For the cleaning of LinMot stators and sliders cleaning agent spray LU06 is recommended.
To improve the sliding characteristics between the stainless steel surface of the slider and the plastic slide
bearing the LinMot lubricant LU02 is prescribed.
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 27 / 32
Ordering information
Item
Description
Item-No.
LU06-250
Klüberfood NH1 4-002 Spray* (250 ml)
0150-2394
LU02-08
Lubricant for linear motors ** (8 g)
0150-1953
LU02-50
Lubricant for linear motors ** (50 g)
0150-1954
LU02-1000
Lubricant for linear motors ** (1000 g)
0150-1955
* LinMot Spray LU06 corresponds to KLÜBERFOOD NH1 4-002 which was developed for the food
processing industry.
** LinMot LU02 Lubricant corresponds to KLÜBERSYNTH UH1 14-31 which was developed for the food
processing industry.
7 Storage, transport, installation altitude
• Sliders are to be stored and transported only in the plastic containers (with cardboard inlay) provided for
this purpose, or already installed and secured in LinMot P stators.
• Remove the slider from this plastic containers only for assembling.
• The storage area must be dry, dust-free, frost-free and vibration-free.
• The relative air humidity should be less than 60 %.
• Prescribed storage temperature: -15 °C…70 °C
• The motor must be protected against extreme weather conditions.
• The air in the storage area must not contain any harmful gases.
• The max. installation altitude is 2'000 m (for higher values contact LinMot) above sea level.
• From 1'000 m, derating of 1 °C per 100 m is to be considered for air cooling.
8 Dimensions
8.1 Stator
8.1.1 PS10-54x120
8.1.2 PS10-54x180
Installation Guide Linear Motors ENG
Page 28 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
8.1.3 PS10-54x240
8.1.4 PS10-54x300
8.2 Slider
Item
Item-No.
Length L [mm / in]
PL01-28x350/270
0150-1380
350 / 13.78
PL01-28x410/330
0150-1381
410 / 16.14
PL01-28x500/420
0150-1382
500 / 19.69
PL01-28x620/540
0150-1383
620 / 24.4
PL01-28x710/630
0150-1384
710 / 27.95
PL01-28x800/720
0150-1385
800 / 31.5
PL01-28x920/840
0150-1386
920 / 36.22
PL01-28x1010/930
0150-1387
1010 / 39.76
PL01-28x1220/1140
0150-1388
1220 / 48.03
PL01-28x1400/1320
0150-1389
1400 / 55.12
PL01-28x1610/1530
0150-1390
1610 / 63.39
PL01-28x1820/1740
0150-1395
1820 / 71.65
PL01-28x2000/1920
0150-1396
2000 / 78.74
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 29 / 32
9 UL Certificate
Installation Guide Linear Motors ENG
Page 30 / 32 P10-54 / P10-54-D24/25/25S NTI AG / LinMot
Installation Guide Linear Motors ENG
NTI AG / LinMot P10-54 / P10-54-D24/25/25S Page 31 / 32
10 Declaration of Conformity and CE-marking
Wir
We
Nous NTI AG
Bodenaeckerstrasse 2
8957 Spreitenbach
erklären in alleiniger Verantwortung, dass das Produkt
declare under our sole responsibility that the product
declarons sous notre seule responsabilité que le produit
Product
Item-No.
Product
Item-No.
PS10-54x120U-BL-TU
0150-2722
PS10-54x240U-BL-TU
0150-2724
PS10-54x120U-BL-TU-D24
0150-2748
PS10-54x240U-BL-TU-D24
0150-2750
PS10-54x120U-BL-TU-D25
0150-2752
PS10-54x240U-BL-TU-D25
0150-2754
PS10-54x120U-BL-TU-D25S
0150-2782
PS10-54x240U-BL-TU-D25S
0150-2784
PS10-54x180U-BL-TU
0150-2723
PS10-54x300U-BL-TU
0150-2725
PS10-54x180U-BL-TU-D24
0150-2749
PS10-54x300U-BL-TU-D24
0150-2751
PS10-54x180U-BL-TU-D25
0150-2753
PS10-54x300U-BL-TU-D25
0150-2755
PS10-54x180U-BL-TU-D25S
0150-2783
PS10-54x300U-BL-TU-D25S
0150-2785
konform ist mit den Anforderungen der Richtlinien,
is conform to the provisions of directives,
est conformé aux exigences des directives,
2014/35/EU (LVD) + 2014/30/EU (EMCD)
gestützt auf die folgenden Normen,
based on the following standards,
base aux normes suivants,
LVD EN61800-5-1:2007
EMCD EN61000-6-2:2005
EN61000-6-4:2007
Jahr der CE-Kennzeichnung:
Year of CE marking:
Annee du marquage CE: 2019
Spreitenbach, 22.01.2019
Dr.-Ing. Ronald Rohner Dr.-Ing. Marco Hitz
CEO NTI AG RESPONSIBLE FOR DOCUMENTATION
© 2019 NTI AG / LinMot Subject to alterations
ALL LINEAR MOTION
FROM A SINGLE SOURCE
Visit http://www.linmot.com/ to find a distributor next to you.
LinMot Europe
NTI AG - LinMot & MagSpring
Bodenaeckerstrasse 2
CH-8957 Spreitenbach
Sales / Administration: +41-(0)56-419 91 91
office@linmot.com
Tech. Support: +41-(0)56-544 71 00
support@linmot.com
Tech. Support (Skype): skype:support.linmot
Fax: +41-(0)56-419 91 92
Web: http://www.linmot.com/
LinMot USA
LinMot USA, Inc.
N1922 State Road 120, Unit 1
Lake Geneva, WI 53147
Sales / Administration : 262-743-2555
Tech. Support: usasupport@linmot.com
E-Mail: usasales@linmot.com
Web: http://www.linmot-usa.com/
Loading...