LINKSYS X6200 Users Manual
Regulatory
Information
X6200
Wi-Fi Modem Router
Linksys X-Series DSL Products
Table of Contents
Contents
Russia, Kazakhstan and Belarus
EAC Mark of Conformity for Russia, Kazakhstan and Belarus . . . . . . . . . . 2
Australia
Radio exposure notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
New Zealand
Telepermit Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
United States of America
FCC Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . 3
FCC Part 68 Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Canada
Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Avis d’Industrie Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mexico
Mexico Regulatory Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety Notices
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
European Union
Declaration of Conformity with Regard to EU Directive
1999/5/EC (R&TTE Directive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
National Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Product Usage Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
User Information for Consumer Products Covered by EU Directive
2002/96/EC on Waste Electric and Electronic Equipment (WEEE) . . . . . . 15
i
Linksys X-Series DSL Products
Regulatory Information
Russia, Kazakhstan and Belarus
The following information applies if you use the product
within Russia, Kazakhstan and Belarus.
EAC Mark of Conformity for Russia, Kazakhstan and Belarus
Australia
The following information applies if you use the product
within Australia.
Radio exposure notice
WARNING: To ensure compliance with
exposure limits to radiofrequency fields, the
antenna of the device should be no closer than
20 cm from the body during use.
New Zealand
The following information applies if you use the product
within New Zealand.
Wireless Connectivity Security on
Linksys ADSL2+ Devices
Setting up the security of the wireless connection
associated with ADSL2+ device is the user’s
responsibility. Telecom will take no responsibility for
charges made to user’s accounts due to poorly organized
wireless security allowing unknown users to connect
to the Internet via this device. Do not complain to the
Telecom Fault Service or Jetstream Helpdesk should this
occur.
General Warning for Linksys ADSL2+
Devices and ADSL2+ Capability
This device has been tested and found suitable to connect
to the Telecom ADSL2+ capability. This indicates only
that Telecom has accepted that this device complies with
the spectrum management plan for ADSL2+ on copper
cable and with simple voiceband compatibility tests
included in PTC273. It does not indicate that this device
is fully compatible with all services accessed via the
ADSL2+ capability. Contact the supplier of the device
when issues occur. Do not call the Telecom Fault Service
or the Jetstream Helpdesk.
Linksys ADSL2+ Devices on Long
Lines
ADSL2+ devices may not achieve the type of “high speed”
operation expected when attached to a line that is longer
than intended by the ITU-T Rec. G.996.1 ADSL standard
i.e. >3 km of 0.4mm cable or a shorter cable length with
several tails or multiples. If the device is installed in such
conditions and does not give the expected “download”
performance, then do not refer the matter to the Telecom
Fault Service or ADSL Helpdesk.
Telepermit Statement
The cabling between the phone port and the phone shall
not exceed 100 metres.
PTC200 General Warning
The grant of a Telepermit for any item of terminal
equipment indicates only that Telecom has accepted
that the item complies with minimum conditions for
connection to its network. It indicates no endorsement
of the product by Telecom, nor does it provide any sort
of warranty. Above all, it provides no assurance that any
item will work correctly in all respects with another item
of Telepermitted equipment of a different make or model,
nor does it imply that any product is compatible with all of
Telecom’s network services.
United States of America
The following information applies if you use the product
within the United States of America.
FCC Statement
This device is restricted for indoor use.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
2
Linksys X-Series DSL Products
Regulatory Information
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used according to the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which is found by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
IEEE 802.11b or 802.11g operation of this product in
the USA is firmware-limited to channels 1 through 11.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
FCC Part 68 Statement
total RENs, contact the telephone company to determine
the maximum REN for the calling area.
If this equipment causes harm to the telephone network,
the telephone company may discontinue your service
temporarily. If advance notice is not practical, the
telephone company will notify the customer as soon as
possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities,
equipment, operations, or procedures that could affect
the operation of the equipment. If this happens, the
telephone company will provide advance notice in order
for you to make the necessary modifications in order to
maintain uninterrupted service.
In the event this equipment should fail to operate
properly, disconnect the unit from the telephone line.
Try using another FCC approved device in the same
telephone jack. If the trouble persists, call the telephone
company repair service bureau. If the trouble does not
persist and appears to be with this unit, disconnect the
unit from the telephone line and discontinue use of the
unit until it is repaired. Please note that the telephone
company may ask that you disconnect the equipment
from the telephone network until the problem has been
corrected or until you are sure that the equipment is not
malfunctioning. The user must use the accessories and
cables supplied by the manufacturer to get optimum
performance from the product.
No repairs may be done by the customer. If trouble is
experienced with this equipment, please contact your
authorized support provider for repair and warranty
information. If the trouble is causing harm to the
telephone network, the telephone company may request
you remove the equipment from the network until the
problem is resolved. This equipment cannot be used on
telephone company provided coin service. Connection to
Party Line Service is subject to state tariffs.
This equipment complies with Part 68 of the FCC Rules.
A label is attached to the equipment that contains, among
other information, its FCC registration number and ringer
equivalence number. If requested, this information must
be provided to the telephone company.
This equipment uses the following USOC Jack: RJ-11.
An FCC compliant telephone cord and modular plug is
provided with this equipment. This equipment is designed
to be connected to the telephone network or premises
wiring using a compatible modular jack, which is FCC
Part 68 compliant. Connection to the telephone network
should be made by using the standard modular telephone
jack.
The REN is useful to determine the quantity of devices
that may be connected to the telephone line and still have
all of those devices ring when your telephone number is
called. In most, but not all areas, the sum of RENs should
not exceed five. To be certain of the number of devices
that may be connected to the line, as determined by the
Canada
The following information applies if you use the product
within Canada.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3 (B)
This device complies with Industry Canada license-
exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including
interference that may cause undesired operation of
the device.
3
Linksys X-Series DSL Products
Regulatory Information
For product available in the USA/Canada market, only
channel 1~11 can be operated. Selection of other
channels is not possible.
The device could automatically discontinue transmission
in case of absence of information to transmit, or
operational failure. Note that this is not intended to
prohibit transmission of control or signaling information
or the use of repetitive codes where required by the
technology.
This product meets the applicable Industry Canada
technical specifications.
The Ringer Equivalence Number (REN) is an indication
of the maximum number of devices allowed to be
connected to a telephone interface. The termination of
an interface may consist of any combination of devices
subject only to the requirement that the sum of the
RENs of all the devices not exceed five.
Le présent matériel est conforme aux specifications
techniques applicables d’Industrie Canada.
L’indice d’équivalence de la sonnerie (IES) sert à indiquer
le nombre maximal de terminaux qui peuvent être
raccordés à une interface téléphonique. La terminaison
d’une interface peut consister en une combinaison
quelconque de dispositifs, à la seule condition que la
somme d’indices d’équivalence de la sonnerie de tous les
dispositifs n’excède pas cinq.
licence.
L’exploitation est autorisée aux deux conditions
suivantes :
1. il ne doit pas produire de brouillage et
2. l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Pour les produits disponibles sur le marché aux ÉtatsUnis et au Canada, seuls les canaux de 1 à 11 peuvent
être utilisés. La sélection d’autres canaux n’est pas
possible.
Le dispositif peut automatiquement cesser d’émettre
en cas d’absence d’informations à transmettre, ou à
cause d’une défaillance technique. Notez que l’objet
n’est pas d’interdire la transmission des informations
de contrôle ou de signalisation ou l’utilisation de
codes répétitifs lorsque requis par la technologie.
Avis d’Industrie Canada concernant
l’exposition aux radiofréquences
Ce matériel est conforme aux limites établies par
IC en matière d’exposition aux radiofréquences
dans un environnement non contrôlé. Ce matériel
doit être installé et utilisé à une distance d’au moins
20 cm entre l’antenne et le corps de l’utilisateur.
Industry Canada Radiation Exposure
Statement
This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum
distance 20 cm between the radiator & your body.
This device and it’s antennas(s) must not be co-located
or operating in conjunction with any other antenna
or transmitter except in accordance with IC multitransmitter product procedures.
Restrictions in the 5 GHz Band
The device for the band 5150-5250 MHz is only for
indoor usage to reduce potential for harmful interference
to co-channel mobile satellite systems.
Avis d’Industrie Canada
CAN ICES-3 (B)/NMB-3 (B).
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de
Cet appareil et son (ses) antenne (s) ne doivent pas être
situés à proximité ou fonctionner en association avec
une autre antenne ou un autre émetteur autre qu’en
respectant les procédures d’ Industrie Canada relatives
au fonctionnement des dispositifs multi-émetteurs.
Restrictions dans la bande 5 GHz
L’appareil pour la bande de 5150 à 5250 MHz est conçu
pour usage à l’intérieur seulement afin de réduire le
potentiel d’interférences pour les systèmes mobiles par
satellite qui utilisent le même canal.
Wireless Disclaimer
The maximum performance for wireless is derived
from IEEE Standard 802.11 specifications. Actual
performance can vary, including lower wireless network
capacity, data throughput rate, range and coverage.
Performance depends on many factors, conditions
and variables, including distance from the access
point, volume of network traffic, building materials and
construction, operating system used, mix of wireless
products used, interference and other adverse conditions.
4
Linksys X-Series DSL Products
Regulatory Information
Avis de non-responsabilité concernant
les appareils sans fil
Les performances maximales pour les réseaux sans fil
sont tirées des spécifications de la norme IEEE 802.11.
Les performances réelles peuvent varier, notamment
en fonction de la capacité du réseau sans fil, du débit
de la transmission de données, de la portée et de la
couverture. Les performances dépendent de facteurs,
conditions et variables multiples, en particulier de la
distance par rapport au point d’accès, du volume du
trafic réseau, des matériaux utilisés dans le bâtiment
et du type de construction, du système d’exploitation
et de la combinaison de produits sans fil utilisés, des
interférences et de toute autre condition défavorable.
Mexico
The following information applies if you use the product
within Mexico.
WARNING: This equipment will be inoperable
when main power fails..
WARNING: The power adaptor is the
equipment´s disconnection device. The power
outlet must be located nearby the equipment
and its access must be easy.
[Arabic]
.
Mexico Regulatory Statement
La operación de este equipo está sujeta a las siguientes
dos condiciones: (1) es posible que este equipo o
dispositivo no cause interferencia perjudicial y (2) este
equipo o dispositivo debe aceptar cualquier interferencia,
incluyendo la que pueda causar su operación no deseada.
Safety Notices
English
WARNING: Do not use this product near
water, for example, in a wet basement or near
a swimming pool.
WARNING: Avoid using this product during an
electrical storm. There may be a remote risk of
electric shock from lightning.
WARNING: To reduce the risk of fire, use only
No.26 AWG or larger telecommunication line
cord..
:
26
AWG
:
:
Български [Bulgarian]
ПРЕДУПРЕЖДЕНИЕ: Не използвайте
устройството в близост до вода, напр. във
влажно мазе или до плувен басейн.
ПРЕДУПРЕЖДЕНИЕ: Избягвайте да
използвате това устройство по време
на буря. Възможно е да съществува
несъществен риск от електрически удар от
светкавица.
5
Loading...