Linksys WMP54GS EU, WMP54GS UK, WMP54GS LA User Manual
A Division of Cisco Systems, Inc.
®
Model No.
PCI Adapter
Wireless-G
WMP54GS (EU/UK/LA)
User Guide
WIRELESS
with SpeedBooster
GHz
802.11g
2,4
Wireless-G PCI Adapter with SpeedBooster
Copyright and Trademarks
Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All
rights reserved. Other brands and product names are trademarks or registered trademarks of their respective
holders.
How to Use This User Guide
This User Guide has been designed to make understanding networking with the Wireless-G PCI Adapter easier
than ever. Look for the following items when reading this User Guide:
In addition to these symbols, there are definitions for technical terms that are presented like this:
Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:
Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.
This exclamation point means there is a caution or warning and is
something that could damage your property or the Wireless-G PCI Adapter.
This checkmark means there is a note of interest and is something you
should pay special attention to while using the Wireless-G PCI Adapter.
This question mark provides you with a reminder about something you
might need to do while using the Wireless-G PCI Adapter.
word: definition.
Figure 0-1: Sample Figure Description
WMP54GS-UG-EU/UK/LA 50621 KL
Wireless-G PCI Adapter with SpeedBooster
Table of Contents
Chapter 1: Introduction 1
Welcome 1
What’s in this Guide? 2
Chapter 2: Planning your Wireless Network 4
Network Topology 4
Roaming 4
Network Layout 5
Chapter 3: Setting up and Connecting the PCI Adapter 6
Starting the Setup Wizard 6
Installing the Adapter 7
Setting Up the Adapter 8
Chapter 4: Using the Wireless Network Monitor 20
Accessing the Wireless Network Monitor 20
Link Information Screens 20
SecureEasySetup 23
Site Survey 25
Profiles 26
Creating a New Profile 27
Appendix A: Troubleshooting 39
Common Problems and Solutions 39
Frequently Asked Questions 40
Chapter B: Using Windows XP Wireless Configuration 43
Appendix C: Wireless Security 46
Security Precautions 46
Security Threats Facing Wireless Networks 46
Appendix D: Windows Help 49
Appendix E: Glossary 50
Appendix F: Specifications 53
Appendix G: Warranty Information 54
Appendix H: Regulatory Information 55
Appendix I: Contact Information 61
Wireless-G PCI Adapter with SpeedBooster
List of Figures
Figure 3-1: Setup Wizard’s Welcome Screen 6
Figure 3-2: Setup Wizard’s License Agreement 6
Figure 3-3: The Connecting the Adapter Screen 7
Figure 3-4: Installng the Adapter 7
Figure 3-5: Positioning the Antenna 7
Figure 3-6: Available Wireless Network 8
Figure 3-7: Available Wireless Network 9
Figure 3-8: SecureEasySetup 9
Figure 3-9: The SecureEasySetup Logo and Location 9
Figure 3-10: SecureEasySetup complete 10
Figure 3-11: Available Wireless Network 11
Figure 3-12: WEP Key Needed for Connection 11
Figure 3-13: WPA-Personal for Connection 12
Figure 3-14: WPA2 - Personal Needed for Connection 12
Figure 3-15: The Congratulations screen 12
Figure 3-16: Available Wireless Network 13
Figure 3-17: Network Settings 13
Figure 3-18: Wireless Mode 14
Figure 3-19: Ad-Hoc Mode Settings 14
Figure 3-20: Wireless Security 15
Figure 3-21: Wireless Security - WEP 15
Figure 3-22: Wireless Security - WPA-Personal 16
Figure 3-23: Wireless Security - WPA2-Personal 16
Figure 3-24: Wireless Security - WPA-Enterprise 17
Figure 3-25: Wireless Security - RADIUS 18
Figure 3-26: Confirm New Settings 19
Figure 3-27: The Congratulations screen 19
Figure 4-1: Wireless Network Monitor Icon 20
Figure 4-2: Link Information 20
Figure 4-3: More Information - Wireless Network Status 21
Wireless-G PCI Adapter with SpeedBooster
Figure 4-4: More Information - Wireless Network Statistics 22
Figure 4-5: The SecureEasySetup button 23
Figure 4-6: The SecureEasySetup Logo and Location 23
Figure 4-7: SecureEasySetup 23
Figure 4-8: SecureEasySetup is complete 24
Figure 4-9: Site Survey 25
Figure 4-10: WEP Key Needed for Connection 25
Figure 4-11: PSK Needed for Connection 25
Figure 4-12: Profiles 26
Figure 4-13: Import a Profile 26
Figure 4-14: Export a Profile 26
Figure 4-15: Create a New Profile 27
Figure 4-16: Available Wireless Network 27
Figure 4-17: Available Wireless Network 28
Figure 4-18: The SecureEasySetup Logo and Location 28
Figure 4-19: SecureEasySetup 28
Figure 4-20: SecureEasySetup complete 29
Figure 4-21: Available Wireless Network 30
Figure 4-22: WEP Key Needed for Connection 30
Figure 4-23: WPA-Personal for Connection 31
Figure 4-24: WPA2 - Personal Needed for Connection 31
Figure 4-25: The Congratulations screen 31
Figure 4-26: Available Wireless Network 32
Figure 4-27: Network Settings 32
Figure 4-28: Wireless Mode 33
Figure 4-29: Ad-Hoc Mode Settings 33
Figure 4-30: Wireless Security 34
Figure 4-31: Wireless Security - WEP 34
Figure 4-32: Wireless Security - WPA-Personal 35
Figure 4-33: Wireless Security - WPA2-Personal 35
Figure 4-34: Wireless Security - PSK + RADIUS 36
Figure 4-35: Wireless Security - RADIUS 37
Figure 4-36: Confirm New Settings 38
Wireless-G PCI Adapter with SpeedBooster
Figure 4-37: The Congratulations screen 38
Figure B-1: Wireless Network Monitor Icon 43
Figure B-2: Windows XP - Use Windows XP Wireless Configuration 43
Figure B-3: Windows XP Wireless Configuration Icon 43
Figure B-4: Available Wireless Network 44
Figure B-5: No Wireless Security 44
Figure B-6: Network Connection - Wireless Security 45
Figure B-7: Wireless Network Connection 45
1
Chapter 1: Introduction
Welcome
Wireless-G PCI Adapter with SpeedBooster
Chapter 1: Introduction
Welcome
Thank you for choosing the Wireless-G PCI Adapter. With this Adapter, your wireless networking experience will
be faster and easier than ever.
Like all wireless products, the Adapter allows for greater range and mobility within your wireless network. This
adapter communicates over the 54Mbps 802.11g wireless standard, which is almost five times faster than
802.11b. But since they share the same 2.4GHz radio band, the Adapter can also communicate with the widely
used 11Mbps 802.11b standard.
PCs equipped with wireless cards and adapters can communicate without cumbersome cables. By sharing the
same wireless settings, within their transmission radius, they form a wireless network.
The included Setup Wizard will walk you through configuring the adapter to your network's settings, step by step.
Then just slide it into your computer's PCI Card slot and enjoy network access with the freedom of wireless.
Once you're connected, you can keep in touch with your e-mail, access the Internet, and share files and other
resources such as printers and network storage with other computers on the network. At home, you can surf the
web or use instant messaging to chat with friends while sitting out on the patio. Your wireless connection is
protected by the new, industrial-strength security of Wireless Protected Access (WPA).
And now, with SecureEasySetup, setting up your network and your Wireless-G PCI Adapter is easier than ever.
Get connected to current-standard 802.11b networks today, and be prepared for the future with the Wireless-G
PCI Adapter from Linksys.
802.11b: an IEEE wireless networking standard
that specifies a maximum data transfer rate of
11Mbps and an operating frequency of 2.4GHz
adapter: a device that adds network functionality
to your PC.
network: a series of computers or devices
connected for the purpose of data sharing,
storage, and/or transmission between users.
802.11g an IEEE wireless networking standard
that specifies a maximum data transfer rate of
54Mbps, an operating frequency of 2.4GHz, and
backward compatibility with 802.11b devices.
Mbps: one million bits per second; a unit of
measurement for data transmission
2
Chapter 1: Introduction
What’s in this Guide?
Wireless-G PCI Adapter with SpeedBooster
What’s in this Guide?
This user guide covers the steps for setting up and using the Wireless-G PCI Adapter.
• Chapter 1: Introduction
This chapter describes the Adapter’s applications and this User Guide.
• Chapter 2: Planning Your Wireless Network
This chapter discusses a few of the basics about wireless networking.
• Chapter 3: Setting Up and Connecting the PCI Adapter
This chapter shows you how to setup and connect the Adapter.
• Chapter 4: Using the Wireless Network Monitor
This chapter show you how to use the Adapter’s Wireless Network Monitor.
• Appendix A: Troubleshooting
This appendix describes some problems and solutions, as well as frequently asked questions, regarding
installation and use of the Adapter.
• Appendix B: Windows XP Wireless Zero Configuration
This chapter instructs you on how to install Window XP Wireless Zero Configuration
• Appendix C: Wireless Security
This appendix discusses security issues regarding wireless networking and measures you can take to help
protect your wireless network.
• Appendix D: Windows Help
This appendix describes how you can use Windows Help for instructions about networking, such as installing
the TCP/IP protocol.
• Appendix E: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
• Appendix F: Specifications
This appendix provides the Adapter’s technical specifications.
• Appendix G: Warranty Information
This appendix supplies the Adapter’s warranty information.
• Appendix H: Regulatory Information
This appendix supplies the Adapter’s regulatory information.
3
Chapter 1: Introduction
What’s in this Guide?
Wireless-G PCI Adapter with SpeedBooster
• Appendix I: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.
4
Chapter 2: Planning your Wireless Network
Network Topology
Wireless-G PCI Adapter with SpeedBooster
Chapter 2: Planning your Wireless Network
Network Topology
A wireless network is a group of computers, each equipped with one wireless adapter. Computers in a wireless
network must be configured to share the same radio channel. Several PCs equipped with wireless cards or
adapters can communicate with one another to form an ad-hoc network.
Linksys wireless adapters also provide users access to a wired network when using an access point or wireless
router. An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an
infrastructure network can talk to any computer in a wired network infrastructure via the access point or wireless
router.
An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and can double the
effective wireless transmission range for two wireless adapter PCs. Since an access point is able to forward data
within a network, the effective transmission range in an infrastructure network can be doubled.
Roaming
Infrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your
wireless PC within your network and the access points will pick up the wireless PC's signal, providing that they
both share the same channel and SSID.
Before enabling you consider roaming, choose a feasible radio channel and optimum access point position.
Proper access point positioning combined with a clear radio signal will greatly enhance performance.
infrastructure: a wireless network that is
bridged to a wired network via an access point.
ad-hoc: a group of wireless devices
communicating directly with each other (peerto-peer) without the use of an access point.
roaming: the ability to take a wireless device
from one access point's range to another without
losing the connection.
ssid: your wireless network's name.
topology: the physical layout of a network.
access point: a device that allows wireless-
equipped computers and other devices to
communicate with a wired network. Also used to
expand the range of a wireless network
5
Chapter 2: Planning your Wireless Network
Network Layout
Wireless-G PCI Adapter with SpeedBooster
Network Layout
Linksys wireless access points and wireless routers have been designed for use with 802.11a, 802.11b, and
802.11g products. With 802.11g products communicating with the 802.11b standard and some products
incorporating both “a” and “g”, products using these standards can communicate with each other.
Access points and wireless routers are compatible with 802.11a, 802.11b and 802.11g adapters, such at the PC
Cards for your laptop computers, PCI Card for your desktop PC, and USB Adapters for when you want to enjoy USB
connectivity. Wireless products will also communicate with the wireless PrintServer.
When you wish to connect your wired network with your wireless network, network ports on access points and
wireless routers can be connected to any of Linksys's switches or routers.
With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at
www.linksys.com/international for more information about wireless products.
router: a networking device that connects multiple
networks together
switch: a data switch that connects computing devices
to host computers, allowing a large number of devices
to share a limited number of ports
6
Chapter 3: Setting up and Connecting the PCI Adapter
Starting the Setup Wizard
Wireless-G PCI Adapter with SpeedBooster
Chapter 3: Setting up and Connecting the PCI Adapter
The PCI Adapter is set up with the Setup Wizard that comes on the CD enclosed with the Adapter. This chapter will
guide you through the setup procedure.
Starting the Setup Wizard
To begin the setup process, insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should
run automatically, and the Welcome screen should appear. If it does not, click the Start button and choose Run.
In the field that appears, enter D:\setup.exe (if “D” is the letter of your CD-ROM drive).
On the Welcome screen, you have the following choices:
Click Here to Start - Click the Click Here to Start button to begin the software installation process.
User Guide - Click the User Guide button to open this User Guide.
Exit - Click Exit to exit the Setup Wizard.
1. To install the Adapter, click the Click Here to Start button on the Welcome screen.
2. After reading the License Agreement, click Next if you agree and want to continue the installation, or click
Cancel to end the installation.
3. Windows will begin copying the files onto your PC.
Figure 3-1: Setup Wizard’s Welcome Screen
Figure 3-2: Setup Wizard’s License Agreement
IMPORTANT: Do not connect the Adapter until you are instructed to
do so or the setup will not work.
7
Chapter 3: Setting up and Connecting the PCI Adapter
Installing the Adapter
Wireless-G PCI Adapter with SpeedBooster
4. The Setup Wizard will now prompt you to install the Adapter into your PC. Click Next and your PC will power
down. After installing the Adapter, as shown below, and restarting your PC, the Setup Wizard will continue.
Installing the Adapter
1. Before connecting the PCI Adapter to your PC, turn off your desktop PC.
2. Open your PC case and locate an available PCI slot on the motherboard. Check with your computer
manufacturer for instructions.
3. Slide the PCI Adapter into the PCI slot. Make sure that all of its pins are touching the slot's contacts. You may
have to apply a bit of pressure to slide the adapter all the way in. After the adapter is firmly in place, secure its
fastening tab to your PC's chassis with a mounting screw. Then, close your PC.
4. Attach the external antenna to the adapter’s antenna port.
5. Power on your desktop PC.
Figure 3-3: The Connecting the Adapter Screen
Figure 3-4: Installng the Adapter
Figure 3-5: Positioning the Antenna
8
Chapter 3: Setting up and Connecting the PCI Adapter
Setting Up the Adapter
Wireless-G PCI Adapter with SpeedBooster
Setting Up the Adapter
The next screen to appear will be the Available Wireless Network screen.
This screen provides three options for setting up the Adapter
• SecureEasySetup. This Adapter features SecureEasySetup. This means that you can set it up with just the
press of a button when connecting to wireless routers or access points that also feature SecureEasySetup.
Both devices on the network must feature SecureEasySetup for this to work.
• Available Wireless Network. (For most users.) Use this option if you already have a network set up with
devices that do not have SecureEasySetup. The networks available to this Adapter will be listed on this
screen. You can choose one of these networks and click the Connect button to connect to it. Click the
Refresh button to update the Available Wireless Network list.
• Manual Setup. If you are not taking advantage of SecureEasySetup and your network is not listed on this
screen, select Manual Setup to set up the adapter manually. This method of setting up the Adapter is
intended for Advanced Users only.
The setup for each option is described, step by step, under the appropriate heading on the following pages.
Click Exit to close the Setup Wizard, if you wish to set up the Adapter later.
Figure 3-6: Available Wireless Network
9
Chapter 3: Setting up and Connecting the PCI Adapter
Setting Up the Adapter
Wireless-G PCI Adapter with SpeedBooster
Setting Up the Adapter with SecureEasySetup
With SecureEasySetup, setting up the Adapter is as simple as pushing a couple of buttons. Before you press any
buttons, though, you should locate the SecureEasySetup button on the device you’re connecting the Adapter to,
such as a wireless router or access point.
1. Starting from the Available Wireless Network screen, click the SecureEasySetup button on the right hand
side.
2. You will be asked to locate the SecureEasySetup button on the device with which the Adapter will be
communicating. If you are not sure where to find this button, click Where can I find the button?.
This will walk you through a couple of screens to help you find the button, which is usually located on the
front of the wireless router or access point.
Figure 3-7: Available Wireless Network
Figure 3-8: SecureEasySetup
Figure 3-9: The SecureEasySetup Logo and Location
10
Chapter 3: Setting up and Connecting the PCI Adapter
Setting Up the Adapter
Wireless-G PCI Adapter with SpeedBooster
3. Press the Cisco logo or SecureEasySetup button on the wireless router or access point. When it turns white
and begins to flash, click the Next button on the Setup Wizard screen. The logo or button will stop flashing on
the wireless router or access point when the Adapter has been successfully added to the network. Repeat
this procedure for any additional SecureEasySetup device.
4. When SecureEasySetup is complete, you may save your configuration to a text file by clicking the Save
button, or print the configuration by clicking the Print button. Click Connect to Network to connect to your
network.
Congratulations! Setup is complete.
To check the link information, search for available wireless networks, or make additional configuration
changes, refer to Chapter 4: Using the Wireless Network Monitor.
NOTE: You can only add one SecureEasySetup device at a time.
Figure 3-10: SecureEasySetup complete
11
Chapter 3: Setting up and Connecting the PCI Adapter
Setting Up the Adapter
Wireless-G PCI Adapter with SpeedBooster
Setting Up the Adapter with Available Networks
If you’re not setting up the Adapter with SecureEasySetup, another method for setting up the Adapter is with the
available networks listed on the Available Wireless Network screen. The available networks are listed in the table
on the center of the screen by SSID. Select the wireless network you wish to connect to and click the Connect
button. (If you do not see your network listed, you can click the Refresh button to bring the list up again.) If the
network utilizes wireless security, you will need to configure security on the Adapter. If not, you will be taken
directly to the Congratulations screen.
1. If wireless security has been enabled on this network, you will see a wireless security screen. If your network
utilizes WEP (Wired Equivalent Privacy) encryption, the WEP Key Needed for Connection screen will appear. If
your network utilizes WPA-Personal or WPA2-Personal, a screen will appear for those encryption methods.
WEP Key Needed for Connection
Select 64-bit or 128-bit.
Then, enter a passphrase or WEP key.
Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The
passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match the
passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If
you have any non-Linksys wireless products, enter the WEP key manually on those products.)
WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption,
enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters.
Valid hexadecimal characters are “0” to “9” and “A” to “F”.
Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.
WPA-Personal for Connection
Figure 3-11: Available Wireless Network
Figure 3-12: WEP Key Needed for Connection
wep (wired equivalent privacy): a method of encrypting network
data transmitted on a wireless network for greater security.
encryption: encoding data transmitted in a network.
12
Chapter 3: Setting up and Connecting the PCI Adapter
Setting Up the Adapter
Wireless-G PCI Adapter with SpeedBooster
Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down
menu.
Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field.
The longer and more complex your Passphrase is, the more secure your network will be.
Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.
WPA2 - Personal Needed for Connection
Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field.
The longer and more complex your Passphrase is, the more secure your network will be.
Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.
2. After the Adapter has been configured for the network, the Congratulations screen will appear. Click Connect
to Network to connect to your network.
Congratulations! Setup is complete.
To check the link information, search for available wireless networks, or make additional configuration
changes, refer to Chapter 4: Using the Wireless Network Monitor.
Figure 3-13: WPA-Personal for Connection
Figure 3-15: The Congratulations screen
Figure 3-14: WPA2 - Personal Needed for Connection
13
Chapter 3: Setting up and Connecting the PCI Adapter
Setting Up the Adapter
Wireless-G PCI Adapter with SpeedBooster
Setting Up the Adapter with Manual Setup
If you are not taking advantage of SecureEasySetup and your network is not listed with the available networks,
click Manual Setup on the Available Wireless Network screen to set up the adapter manually.
1. After clicking Manual Setup, the Network Settings screen will appear. If your network has a router or other
DHCP server, click the radio button next to Obtain network settings automatically (DHCP).
If your network does not have a DHCP server, click the radio button next to Specify network settings. Enter
an IP Address, Subnet Mask, Default Gateway, and DNS addresses appropriate for your network. You must
specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS
addresses, leave these fields empty.
IP Address - This IP Address must be unique to your network.
Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.
Default Gateway - Enter the IP address of your network’s Gateway here.
DNS 1 and DNS 2 - Enter the DNS address of your wired Ethernet network here.
Click Next to continue, or click Back to return to the Available Wireless Network screen.
Figure 3-16: Available Wireless Network
Figure 3-17: Network Settings
14
Chapter 3: Setting up and Connecting the PCI Adapter
Setting Up the Adapter
Wireless-G PCI Adapter with SpeedBooster
2. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio
button if you want to connect to a wireless router or access point. Click the Ad-Hoc Mode radio button if you
want to connect to another wireless device directly without using a wireless router or access point. Then,
enter the SSID for your network.
Infrastructure Mode - Use this mode if you want to connect to a wireless router or access point.
Ad-Hoc Mode - Use this mode if you want to connect to another wireless device directly without using a
wireless router or access point.
SSID - This is the wireless network name that must be used for all the devices in your wireless network. It is
case- sensitive and should be a unique name to help prevent others from entering your network.
Click Next to continue or Back to return to the previous screen.
3. If you chose Infrastructure Mode, go to Step 4 now. If you chose Ad-Hoc Mode, the Ad-Hoc Mode Settings
screen will appear.
Select the correct Channel for your wireless network. The channel you choose should match the channel set
on the other devices in your wireless network. If you are unsure about which channel to use, keep the default
setting.
Then, select the Network Mode in which your wireless network will operate. In Mixed Mode, Wireless-B and
Wireless-G devices can both operate on the network, though at a slower speed. In G-Only Mode, no Wireless-
B devices can operate in the network.
Click Next to continue or click Back to change any settings.
Figure 3-18: Wireless Mode
Figure 3-19: Ad-Hoc Mode Settings
15
Chapter 3: Setting up and Connecting the PCI Adapter
Setting Up the Adapter
Wireless-G PCI Adapter with SpeedBooster
4. The Wireless Security screen will appear. This step will configure wireless security.
If your wireless network doesn’t use wireless security, select Disabled and then click the Next button to
continue. Proceed to Step 6.
From the Security drop-down menu, select WEP, WPA-Personal, WPA2-Personal, WPA-Enterprise or
RADIUS for your network’s Encryption Method. WEP stands for Wired Equivalent Privacy, WPA uses a security
standard stronger than WEP encryption, and RADIUS stands for Remote Authentication Dial-In User Service. If
you don’t want to use encryption, select Disabled. Then, click the Next button to continue or the Back button
to return to the previous screen.
WEP
WEP - To use WEP encryption, select 64-bits or 128-bit characters from the drop-down menu, and enter a
passphrase or key.
WEP Key- The WEP key you enter must match the WEP key of your wireless network. If you are using 64-bit
WEP encryption, then the key must consist of exactly 10 hexadecimal characters. If you are using 128-bit
WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal
characters are “0” to “9” and “A” to “F”.
Passphrase - Instead of manually entering a WEP key, you can enter a passphrase in the Passphrase field, so
a WEP key is automatically generated. This case-sensitive passphrase must match the passphrase of your
other wireless network devices and is compatible with Linksys wireless products only. (If you have any nonLinksys wireless products, enter the WEP key manually on those products.)
TX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit
key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box.
Authentication -The default is set to Auto, where it auto-detects for Shared Key or Open system. Shared
Key is when both the sender and the recipient share a WEP key for authentication. Open key is when the
sender and the recipient do not share a WEP key for authentication. All points on your network must use the
same authentication type.
Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the
previous screen.
Figure 3-20: Wireless Security
encryption: encoding data transmitted in a network.
Figure 3-21: Wireless Security - WEP
wep (wired equivalent privacy): a method of encrypting network
data transmitted on a wireless network for greater security.
Loading...