FiberLink-200
User’s Manual
10/100TX / 100FX Fiber Optic Converter
fully compliant with the IEEE 802.3u
10/100Base-TX / 100Base-FX
Standard
www.linkpro.com.tw
10/100TX / 100FX Fiber Optic Converter
It is a Fast Ethernet 10/100Base-TX to Fiber 100Base-FX
converter, which is fully compliant with the IEEE 802.3u
standard, features one fiber port using SC or ST connector
and one STP RJ-45 10/100Base-TX port. It supports
conversion of Fast Ethernet 10/100Base-TX port to fiber
optic cabling. It is automatic for either full or half duplex
mode. Full-duplex cabling provides bandwidth of up to
200Mbps and allows for transmission distance up to 2 km
over multi mode fiber or up to 100 km over single mode fiber.
FiberLink200 also provides 8 Jumpers for advance function
setting, such as fix mode duplex, speed, Flow control…etc.
Specifications
IEEE802.3u Fast Ethernet 10/100Base-TX and
100Base-FX standards
Features STP and Fiber connector
….. RJ45 and SC connector (multi-mode)
….. RJ45 and SC connector (single-mode)
….. RJ45 and ST connector (multi-mode)
Data Transfer Rate: 10/100Mbps(half duplex),
20/200Mbps(Full duplex)
Auto-MDIX for STP 10/100 port
Support Store-and-Forward and Modified
Cut-and-through mode
Support Upto 1600 bytes packet size.
--1--
Support 802.3x collision base backpressure.
TX Duplex Mode: Full or Half duplex mode ( default :
Auto-Negotiation )
LED: Power, speed, FX Link/Act, TX Link/Act and
half/full duplex
Power Requirement: Max. 2.0Watt (external switching
power adapter DC5V/1000mA)
Ambient Temperature:
0
℃
to
50
℃
Humidity: 5% to 90%
Dimension: 25(H) x 95(W) x 75 mm (L)
Cable:
UTP: Cat. 5 UTP cable
Fiber: 62.5/125um multi-mode fiber optic cable,
upto 2Km
10/125um single-mode fiber optic cable,
upto 100Km depends on the fiber transceiver.
--2--
10/100TX / 100FX Fiber Optic Converter
Package Contents
Before going any further, please make sure that you have
the following parts in this package.
•
One FL-200SC (or ST) Fiber Optic converter
•
One External AC to DC power adapter ( 5VDC 1A )
•
One user’s manual
NOTE: Please DO NOT use any other power adapter for
FL-200SC/ST
Panel Contents :
LED Mark State Description
POWER PWR ON Power is received
OFF Power is not received
100Mbps 100M ON TP port work on 100M speed
OFF TP port work on 10M speed
TX Link/Act TX ON A TX port good Link status
has been established.
Blinking During Data Transfer or
Receiving
FX Link/Act FX ON A FX port good Link status
has been established.
Blinking During Data Transfer or
Receiving
Full Duplex FDX ON TX/FX port working on
Full duplex mode
--3--
Port Description:
PORT Mark Description
TX 10/100Base-TX It is connected to LAN card or
connected to hub
100FX 100Base-FX It is connected to other end of
Fiber Optic Transceiver.
**Note : The TX port support Auto-negotiation for
10/100M and Auto-MDI/MDIX capability.
Converter Advance function Setting :
There are 8 Jumpers on the PCB board, refer to below table
for detail :
JP1 open System reserved (default)
JP2 Open System reserved (default)
JP3 Open System revered (default)
JP4 close TP port supports auto-negotiation
with limited capability (defined in JP6)
open TP port supports auto-negotiation
with 10M/100M, full/ half capability
(default)
JP5 close 802.3X enable on TX and FX port
open 802.3X disable on TX and FX port
JP6 close Set TX port work on 100M speed
( Valid when JP4 close)
open Set TX port work on 10M speed
( Valid when JP4 close)
JP7 close Set TX port on Half Duplex mode
open Set TX port on Full Duplex mode
JP8 close Set FX port on Half Duplex mode
open Set FX port on Full Duplex mode
--4—
To set advance function of Converter, please remove the
upper case and find out the Jumpers location as below:
Jumpers Location of FL-200SC/ST
Ordering Information:
FL-200ST : 10/100TX to 100FX Fiber Optic Converter
ST connector, Multi-mode 2KM
FL-200SC : 10/100TX to 100FX Fiber Optic Converter
SC connector, Multi-mode 2KM
FL-200SC15: 10/100TX to 100FX Fiber Optic Converter
SC connector, Single-mode 15KM
FL-200SC40: 10/100TX to 100FX Fiber Optic Converter
SC connector, Single-mode 40KM
FL-200SC60: 10/100TX to 100FX Fiber Optic Converter
SC connector, Single-mode 60KM
FL-200SC80: 10/100TX to 100FX Fiber Optic Converter
SC connector, Single-mode 80KM
FL-200SC100: 10/100TX to 100FX Fiber Optic Converter
SC connector, Single-mode 100KM
--5--
Loading...