400M Wireless 3G SDI/HDMI Extender User Manual
This is a Wireless HD HDMI/SDI transm ission products that use the highest level of wireless c ommunication technology
to enable transmit lossless, uncom pressed, no-delay 3G SDI or full HD HDMI signal .This product includes a transmitt er
and a receiver, and is equipped with 3G/HD SDI interface and full HD HDMI interface. The transmitter has two antennas
and the Receiver has five antennas.The antennas’ operate frequency is 5.1GHz~5.9GHz, and these frequency is changeable
through the software configuration to adopt the wireless regulatory requirements in the world.
Application
400 m
●
HDMI 1.3 compliant
●
Support SMPTE 425M , SMPTE 424M, SMPTE 292M Standard
●
Support HDMI and 3G-SDI inputs and outputs
●
Support point to point, and point-to-multiple network topology
●
Support resolutions up to 1080P@60Hz, zero delay and no compression
Please c heck below devices and accessories before installation,if there are m issing ,please contact your distributor.
●
Support 5GHz ISM frequency band, maximum 10 frequency channels selected by buttons with OLED display
●
Maximum transmission range is 1300ft(400 meters)
●
Transmitter
1PCS
●
Support display DC power status, video status and receiver RSSI by OLED
●
Receiver
1PCS
●
Support Wide range power supply,range from 7V to 36V
●
2 Pin LEMO to D-Tap Cable
2PCS
●
Support Optional Sony F970,V-mount and G-mount, battery buckle, convenient for field battery install and replacement
●
5GHz Antennas
8PCS
●
Support ±8 KV ESD protection level (HBM, Contact discharge)
●
Magic Arm
1PCS
●
Industrial case, stable, reliable and convenient
●
User manual
1PCS
Features
1
Panel Diagram
Installation
2
400M Wireless 3G SDI/HDMIExtender User Manual
Camera Transmitter Receiver Monitor
Transmitter
Receiver
Item Description
Attentions:
Interface
Transmitters
Receiver
SDI input(BNC female);SDI Loop out(BNC female);HDMI
input(Type A female);DC input(2pin LEMO fe male)
SDI output(BNC female);HDMI output (Type A
female);DC input(2pin LEMO female)
Below skills will be usable When some problems happened, lik e as connecti+L59:T68on distance short, no connection, not stable or screen flicker
Power <6.5W TX or <6W RX
and so on
Video bandwidth Maximum TMDS clock frequency 148.5MHz, 4.45Gbps
1) Open the function of scan tools, screen out the interrupt signals against wireless environment.
Resolution and
distance
1080P@60Hz 1300ft
Turn off the Transmmiter at worksit e and then press Receiver's Menu button for 5 seconds for choosing the 2nd item named AFS Trigger.
Audio formats SDI embedded 4 channel 24 bit/48KHz
Push Menu button as OK function,the signals with good performance will be choosed out by Receiver after detected the signals all around,
Bandwidth 40MHz
and these signals will be shown on screen.
Frequency Band 5.0 GHz~ 5.9GHz, Configurable with China、American、Japan、Europe etc.
Transmission
Power
Maximum 21dBm /
2) Check the Antenna and SMA Connectors: Keep the Transmitters and Receivers as connections status, push the menu button under
Receive
/ -75dBm
the screen for 5 seconds. Choose the 1st item named Signal Info. Push Menu button as OK function, there will have four-line
SDI Meta Data Time code(LTC VITC1 VITC2);Remote Control(Trigger);
parameter index on screen,Which are SNR IN/SNR OUT/PIN/Audio BER/PK T BER
ESD Level HBM +/-8kv (Contact Discharge)
Dimension
x W x H): 80.30mm x 34.60mm x 134.40mm W x H): 156.60mm x 43.00mm x 141.40
mm
*
SNR IN
: There are five columns of data, which stands for fi ve antenna's peformance,these numbers must over 24 value.
Net Weight 0.232kg per unit (No antenna included) 0.512kg per unit (No antenna included)
The larger the value, the better the performance. If one(s) of them under 24,then the Antenna(s) looss or the Ant enna/SMA connectors
Temperature 0 ~ 40 °C (operation), -20~60 °C (stock)
broken probably.
*Specifications are subject to change without notice.
*
SNR OUT
: There are two columns of data,the last two columns stands for the performance of Transmm iter'santenna.
The value must over 15.The larger the value,the better the performance.
*
PIN
: There are five columns of data,which stands for t he numbers of lost packets when machine work on, the valus must under 60.
Follow the following solves :
The bigger the value, the more complete the data transm ission.
●
Please check the power supply of transmitter and receiver first. If power is supplied by battery or external power supply,
●
Please ensure that the battery or external power supply is energized and output normally.
*
AUDIO BER
:There is one column of data, which stands for Audio Pac ket Loss.Reference value is 0. The larger the value,
●
Please check whether the antenna connected to the transmitt er and receiver is firmly installed.
the more packet loss the audio will be.
●
please check whether the video output format of the cam era is compatible with this product.
●
Please check if the battery is too low.
●
Make sure that transmitters and receivers are placed at leas t 1.5 meters above the ground.
●
If the problem still can not be s olved, please contact your supplier.
400M Wireless 3G SDI/HDMI Extender User Manual
400M Wireless 3G SDI/HDMI Extender User Manual
Specificaiton
Common troubleshooting
3
4
Loading...