Operating Instructions
1
100m 1x2 HDBaseT Splitter, HDCP2.2 compliant
Support POC, Ethernet, RS232 Pass through
Features
•Incorporate HDBaseT technology
•Distribute 1 Ultra HD HDMI signal to 2 identical HDBaseT output, with 2 x loop HDMI output
and 2 Ethernet ports
•HDCP 2.2 compliant (HDCP 2.2 in, HDCP 1.4 out)
•Support resolutions to 4K@60Hz, YUV 4:2:0, VESA resolution up to 1920x1200
•Support Dolby TrueHD, DTS-HD Master Audio
•With wide-band Bi-Direction IR control (38 ~ 56 kHz)
(IR extension from Sender to Receiver or from Receiver to Sender)
•HDBaseT output 2 support Ethernet pass through
•Support RS232 pass through
•Support CEC, 3D
•Support POC (Receiver powered by HDBaseT Splitter)
•DC 12V power supply
Operating Instructions
2
Operating Instructions
7
-5 to +35 C(+23 to +95 F)
5 to 90%RH (No Condensation)
10.2Gbps
Resolutions
up to 4K@60Hz, YUV 4:2:0
VESA
resolution
1x HDMI input
2x HDMI loop output
2x RJ45 output
1x Power DC receptacle
2x Phoenix RS232 port
2x Ethernet port
100m(1080P), 70m(4K)
110-240V/ 12V DC power supply
15Watts
L220.2xW112.7xH27.5mm
1200g
Packing contents
1) Main Unit: 1x2 HDBaseT Splitter
2) 1x Power supply DC 12V
3) 1x IR-TX cable
4) 2x IR-RX cable
5) 2x Phoenix plugs for RS232 cable termination
6) 4x screws
7) 2x detachable mounting ears
8) Operating Instruction manual
TABLE OF CONTENTS
Package Contents
Dimensional drawing
Panel Descriptions
Connecting and Operating
Applications
Maintenance
Product Service
Warranty
Operating Instructions
6
Operating Instructions
3
VESA Resolution
640x480
800x600
1024x768
1280x768
1280x960
1280x1024
1680x1050
1920x1080
1280x720
1360x768
1400x1050
1920x1200
60Hz
Refresh rate VESA Resolution
Dimensional d
Support 1920x1200 under EDID “1 0”.
rawing
2
27,5
104
112,74
220,2
1
1
Operating Instructions
4
Operating Instructions
5
Please restart the splitter when change EDID mode!
Front Panel
Rear Panel
1
RS232 port
2
DIP switch for EDID setting
3
Indicator of out
5
Indicator of Loop out
6
Indicator of Power
4
HDMI Input port
1
3
5
IR-RX(1&2) ports
7
DC 12V Power
Note:
Connecting and operating
1) Connect the HDMI input source into HDBaseT splitter.
2) Connect HDBaseT splitter and Receiver over Cat6 cable, The Cat6 cable must follow
EIA-TIA 568b standards.
3) Connect the HDMI output of Receiver to the HDMI Display.
HDBaseT ports
Ethernet port
IR-TX port
2
4
6
HDMI Output ports
EDID
0 0
0 1
1 0
1 1
4K@60Hz、YCBCR420、3D、DOLBY5.1
1080P@60Hz、2CH
1080P@24Hz、3D、DOLBY5.1
4K@30Hz、2CH
7) To get on the ethernet,pls connect as below steps:
1.Connect ethernet cable into ethernet port on HDBaseT splitter.
2.Connect ethernet cable with TV and ethernet extender receiver.
Note:1.The ethernet function is designed for ethernet compatib
le receiver units only.
2.Output2 with ethernet function.
4) Connect IR TX cables to the IR-TX sockets on the splitter and connect IR RX cables to the IR-RX
sockets on the splitter.
5) Connect IR RX cable to IR-In port of Receiver, connect IR TX cable in to IR-Out port of Receiver.
6) Power up all units, the splitter,Receiver, sources and displays.
Power ON/OFF (“ ”: off; “ ”: on)
Loading...