How it Works
Linkcom
Loading...
Link View HNVR16
User Manual
84 pgs5.7 Mb0

Linkcom Link View HNVR16, HBR-09EE User Manual

Download
0
Link View HNVR16
Hybrid NVR 16 channels
User Guide
Please find the latest version of the manual and firmware at www.linkcom.fr
1
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of insinuated "dangerous voltage" within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral rhombus is intended to alert the user to the presence of important operating and maintenance (servicing) instruction in the literature accompanying the product.
USERS OF THE SYSTEM ARE RESPONSIBLE FOR CHECKING AND COMPLYING WITH ALL FEDERAL, STATE, AND LOCAL LAWS AND STATUTES COIPCERNING THE MONITORING AND RECORDING OF VIDEO AND AUDIO SIGNALS. LINKCOM SHALL NOT BE HELD RESPONSIBLE FOR THE USE OF THIS SYSTEM IN VIOLATION OF CURRENT LAWS AND STATUTES.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
2
TABLE OF CONTENTS
1 INTRODUCTION......................................................................................................................3
1.1 FEATURE.......................................................................................................................3
1.2 SPECIFICATION..........................................................................................................3
2 HARDWARE OVERVIEW......................................................................................................6
2.1 FRONT PANEL.............................................................................................................6
2.2 CAMERA & MONITOR LOOPING...........................................................................8
2.3 ALARM TRIGGER.......................................................................................................8
2.4 PTZ (PAN, TILT AND ZOOM) CAMERA...............................................................10
3 SYSTEM SETUP ..................................................................................................................... 11
3.1 MENU SETUP INTERFACE(GUI)........................................................................... 11
3.2 LIVE VIEWING AND POP-UP MENU....................................................................13
3.3 CAMERA SETUP........................................................................................................17
3.4 RECORD SETUP ........................................................................................................27
3.5 ALARM SETUP...........................................................................................................28
3.6 NETWORK SETUP ....................................................................................................30
3.7 AUTHORITY SETUP.................................................................................................35
3.8 DISK MANAGEMENT...............................................................................................37
3.9 SYSTEM SETUP .........................................................................................................39
4 HYBRID DVR PLAYBACK...................................................................................................44
4.1 TIME SEARCH ...........................................................................................................45
4.2 EVENT SEARCH........................................................................................................45
4.3 BACKUP.......................................................................................................................46
4.4 SYSTEM LOG .............................................................................................................47
5 BACKUP PLAYBACK ...........................................................................................................48
5.1 MAIN SCREEN SETTING.........................................................................................48
5.2 PLAYBACK OPERATION........................................................................................51
6 NETWORK VIEWING & PLAYBACK...............................................................................54
6.1 IP ADDRESS SETUP ON PC SITE...........................................................................54
6.2 OPTIONAL MICROSOFT INTERNET EXPLORER SETUP..............................56
6.3 LOGIN ..........................................................................................................................58
6.4 REMOTE CONTROL.................................................................................................59
6.5 CONFIGURE...............................................................................................................64
APPENDIX A: RECORDING TIME LAPSE (HOURS).............................................................79
APPENDIX B: HDD COMPATIBLE TABLE..............................................................................80
APPENDIX C: ERROR MESSAGE LIST....................................................................................82
3
1 INTRODUCTION
1.1 FEATURE
Support H.264 / MPEG4 / MJPEG decoding & H.264 encoding.Support up to 16-channel IP cameras input.Support up to 8-channel analog cameras input.Analog camera recording rate up to 120 PPS @ D1.Real-time Display & Playback.Support 5 Megapixel IP Camera for each channel.Audio：4 in & 1out.Support HDDs x4.HDD damaged block detection & temperature alarm system (HDD
S.M.A.R.T).
Support Pre-alarm recording.Support Privacy Mask.Support e-SATA interface.Support HDMI Video interface .Graphic User Interface ( GUI ).Support time-point backup function under Ethernet remote control mode. User
can select any time period to process backup from remote side.
Support time-search & event-search function under Ethernet remote control
mode.
Up to four online clients for independent remote control; individual live-time,
play-back & time-search function available
Support PPPoE/ Static/ DHCP IP & DDNS.Powerful mobile surveillance function, support i-Phone & Android
1.2 SPECIFICATION
MODEL
HBR-09EE
System
OS
Embedded Linux
connector
Ethernet
RJ-45, 10/100/1000 Mbps x1
VGA output
D-SUB output
HDMI output
HDMI output
USB 2.0
Front : 2 ports
Power
DC-12V, 5A
Video andAudio
4
Video input (IP cam, Max)
16 channels
Video input (Analog, Max)
8 channels
Audio input
4 channels
Audio output
1 channel
Hybrid DVR Functions
Camera Name
Max. 20 characters
Screen Split Control
1, 4, 9,16
Image Control
Contrast / Brightness / Saturation / Hue
Recording mode
Manual / Schedule / Alarm
Pre Recording
1~5 sec
Watermark
Support
Searching and Playback
Search Method
Date / Time / Event
Date/ Time / Event Search
Selectable on the calendar
Log Search
Through the log data to find the video event / time
Backup Type
USB
Remote Client Software
Monitoring Environment
Link View for iPhone / iPad /Android, Web site
IP / Analog cam Live View
9 Channels
Remote Search
Web site remote time / event search
System Monitoring and Recovery
Monitoring
Watchdog
Alarm
Alarm Input
8 inputs
Alarm output
1 outputs
Peripheral Devices
Audio in
3.5 Ø Earphone stereo jack / RCA x4
Audio out
3.5 Ø Earphone stereo jack
RS 485
2- pin terminal
STORAGE & BACKUP DEVICE
INTERNAL HDD SUPPORT
SATAHDD x 4
EXTERNAL USB BACKUP DEVICE (PAN
USB x2
5
DRIVE, HDD, BURNER)
E-SATA
x1
RAID
N/A
Networking
Type
Static/ DHCP/ PPPoE/DDNS
Environment
Operating Temp.
0 - 45 ℃ / 32~113 F
Humidity
0~80% RH (non-condensing)
Language
Type
English / Traditional Chinese / Simple Chinese / Russian / Italian / Japanese / Czech / France / Germany / Spanish /
Physical
Dimensions (W x H x D)
360 x 60 x 311 mm
Weight
4 KG
* SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
2 HARDWARE OVERVIEW
2.1 FRONT PANEL
Hybrid DVR OPERATION
NO.
LABEL
OPERATION
1
LED
Led Indicator
2
/
USB Connector/ USB Mouse Connector
3
MIC IN
Microphone input(Phone Jack)
4
AUDIO OUT
Earphone output(Phone Jack)
4321
76 8
10 11 12
22
6
7
BACK PANEL
NO.
LABEL
OPERATION
1
E-SATA
E-SATA interface
2
AUDIO OUT
Audio Output
3
VIDEO OUT (VGA)
Connect to LCD monitor
4
POWER
Connect to power adapter (AC 12V/5A)
5
VIDEO OUT (HDMI)
HDMI video output
6
ETHERNET
RJ-45 connector
7
ALARM IN/ RELAY OUT/ RS-485
8 alarm in/ 1 relay out/ RS485
8
AUDIO IN
Audio input
9
VIDEO IN
BNC video input
10
FAN
The fan louvers
8
2.2 CAMERA & MONITOR LOOPING
Here recommend link cameras by sequence to avoid unexpected image broken, from
CH1, CH2, CH3, CH4…….
2.3 ALARM TRIGGER
There are three types of alarms: Motion detection, Video Loss Alarm, and External Alarm. Following are the possible action when alarm is triggered. Every action is configurable (Ex. the screen display pattern, the relay triggered time.etc) and will be explained in the later chapter.
A. When Motion detection happens:
a. The live screen pattern can be switch to single channel screen or split screen. b. External relay/ built-in buzzer can be triggered. c. Alarm timepoint can be recorded in the event list, and you can search for the event
in playback.
d. On the channel which the alarm triggered, the icon pops up to remind the user. e. The pre/ post-alarm recording video can be sent to e-mail/ uploaded to FTP.
f. CGI can be sent to an http server.
B. When External Alarm happens:
a. External relay/ built-in buzzer can be triggered. b. Alarm timepoint can be recorded in the event list, and you can search for the event
in playback.
c. On the channel which the alarm triggered, the icon pops up to remind the
user. d. The pre/ post-alarm recording video can be sent to e-mail/ uploaded to FTP. e. CGI can be sent to an http server.
C. When Video Loss Alarm happens:
a. External relay/ built-in buzzer can be triggered. b. Alarm timepoint can be recorded in the event list, and you can search for the event
in playback.
c. On the channel which the alarm triggered, the icon pops up to remind the
user.
CGI can be sent to an http server.
9
D. Alarm in connecter
EX1：Connect GND & Alarm to external IR detector.
EX2：Connect N.O & COM to external siren.
Depending on the external device type,
You may connect N.C & COM to external device.
D+
RS-485: sends +/ receives +
D -
RS-485: sends -/ receives -
GND
Ground
ALARM IN 1-8
Alarm input
N.C
Relay: Normally close
N.O
Relay: Normally open
COM
Relay: Common
10
2.4 PTZ (PAN, TILT AND ZOOM) CAMERA
Following diagram for HYBRID DVR connect between PTZ camera & joystick controller, for HYBRID DVR to control PTZ camera please make sure the CAMERA ID, BANDRATE (default at 9600 bps) and RS-485 cable.
2 CORE
Under “Two Core” connection, controller can control speed dome without integrated protocol into HYBRID DVR. Moreover, one keyboard can connect MAX 256 units of speed dome.
11
3 SYSTEM SETUP
3.1 MENU SETUP INTERFACE(GUI)
A. CAMERA SETUP B. RECORD SETUP
C. ALARM SETUP D. NETWORK SETUP
12
E. AUTHORITY SETUP F. DISK MANAGEMENT
G. SYSTEM SETUP H. EXIT
13
3.2 LIVE VIEWING AND POP-UP MENU
Tick the box to fix the function panel on right side. Untick it, then the function panel will be hidden when the mouse moves away.
A. GUI MENU BAR
With live viewing mode, press this button to get into the GUI menu.
B. DISK INFORMATION
With live viewing mode, press this button to display disk information.
C. DIGITAL ZOOM
In the live full screen mode, left-click the button of the mouse to pull a range to zoom in or zoom out the image. User can right-click the button of the mouse to disable this function. (NOTE: Using the mouse to operate digital zoom can zoom in to max. 16 times.) Moreover, user can also use ZOOM key on the front panel to perform this function. (First, click ZOOM Key and then click ▲▼◄► key to select zoom in or zoom out position. Finally, click ENTER key to complete the setting. Moreover, click ZOOM Key again can disable digital zoom function. Using the panel key to perform
14
zoom in function is fixed at 2 times.)
D. PTZ CONTROLLER
Within live-viewing mode, Clicks this button to get into the PTZ setup menu. User can right-click the button of the mouse to exit PTZ Setup.
NOTE： Only for the camera supported PTZ function.
PTZ CONTROL
Press the minimization icon then the control panel becomes smaller:
Move the mouse and the arrow will follow the mouse and change direction. In this mode user can click on the live view to control direction instead of the direction key on control panel.
When a analog camera is connected, you can set up by clicking the tools icon:
15
E. AUDIO VOLUME
Press this button, and the audio volume control board will pop up.
F. AUTO SWAP
Press it to start auto swap. The interval depends on the setting in IPCam Image Setup when it’s on single channel view. For split screen the switch dwell interval is 5 sec
G. DISPLAY CONTROL
Within live-viewing or playback mode, use display control to switch the camera channel.
H. RECORD AND PLAYBACK CONTROL
Same as front panel controller and remote controller.
I. SOUND OUTPUT / PTZ CONTROL
There are little icon on the right top of the live vide of every channel. Click to
enable the sound output. Click to PTZ call out the control board. Note that if those functions are not support by the camera linked, you will not see the corresponding icons.
The sound options do not affect the audio recorded into playback video. As long as the audio setup is enabled, the playback video includes audio even the sound output here is turned off.
J. RECORDING STATUS
Beneath the date and time, it displays the current recording type:
Record mode: Schedule – NO REC period
16
Record mode: Schedule – ALARM REC period Record mode: Alarm trigger
Record mode: Manual – Stop Recording
Record mode: Schedule – FULL REC period Record mode: Manual – Recording
17
3.3 CAMERA SETUP
A. Camera Setup
Hybrid DVR can connect two various cameras, analog camera or IP-Cam.
Camera Type in Analog-CAM
Camera Type in IP-CAM
18
A-1. IPCam Quick Search
Press the “IPCam Quick Search” button and click “Search Device” button in the following, DVR will search the IPCAM devices which IP address are setup as the same domain as DVR IP address. Moreover, click the IPCam device which from the list can import the device information to the channel automatically without any manual key-in step. The IPCam has to be under the same LAN with DVR in order to connect successfully. Ex. If DVR IP address is 192.168.10.33, IP Cam IP address should be 192.168.10.X. You can edit IP Cam IP address here or on the IP Cam.
a. Normal Mode
Enable this channel. Key in the IP address, port, username, and password of
the device you prepare to connect. You can find the information on the IP Cam.
Click the “connect IPCAM” button, the message will show in “State” column
to tell you whether connection succeeds or not.
Note: To the camera connected via ONVIF protocol, the PTZ control function
is not supported. Note: To the camera connected via ONVIF protocol, the PTZ control function is not supported.
b. RSTP Mode
Under RTSP Mode, the DVR only support the IP address indication, the live video, and video recording. Other functions like motion detection are not supported.
19
Key in the IP address, port, username, and password of the device you
prepare to connect. You can find the information on the IP Cam.
To link to the IP camera, check the RTSP Path settings of your IP camera,
and key in the corresponding values of two streams in “RTSP Path 1” and
“RTSP Path 2”.
Note: When you select RTSP mode, make sure the substream resolution of
camera is VGA(640x480). Or you will receive the warning message when you try to connect with the camera:
Here we lists some RTSP setting for sample:
RTSP Path 1 (IPCam Main stream)
RTSP Path 2 (IPCam Sub stream)
Result
1920 x 1080
640 x 480
OK. DVR takes 1920x1080 streaming for single channel view, and 640x480 streaming for split screen.
1920 x 1080
N/A (Fill in nothing on "RTSP Path 2")
Error Message: ”Invalid Substream Resolution! Please modify IPCam.”
DVR takes 1920x1080 streaming for both single channel view and split screen. However, it can only allow 640x480 resolution for split screen, so it shows error in return.
640 x 480
N/A (Fill in nothing on "RTSP Path 2")
OK. DVR takes 640x480 streaming for both single channel view and split screen.
N/A (Fill in nothing on "RTSP Path 1")
640 x 480
OK. DVR takes 640x480 streaming for both single channel view and split screen.
20
640 X480
1920 x 1080
OK. DVR takes 1920x1080 streaming for single channel view, and 640x480 streaming for split screen.
1920 x 1080
1920 x 1080
Error Message: ”Invalid Substream Resolution! Please modify IPCam.”
DVR takes 1920x1080 streaming for both single channel view and split screen. However, it can only allow 640x480 resolution for split screen, so it shows error in return.
c. ROI
This function allows users to set up the channel as an attached channel. An attached channel is based on a normal/ RTSP channel has been set up, and can display the same live view as the normal/ RTSP channel. The attached channel is not physically linked to any camera, so it doesn't increase the bandwidth loading. Users cannot do camera setup (like motion detection or image adjustment) on attached channel.
1. Enable: Choose “Attached”.
2. Attached Channel: Select a connected normal/ RTSP channel in the drop-down menu.
Ratio: Use the arrows to adjust the zoom ratio, and press the red frame to drag it
to the area that you want it to show on the live view screen.
A-2. Connect IPCAM：After insert the IPCAM related information, click this button
to test the connection circumstances.
Note: To the camera connected via ONVIF protocol, the PTZ control function is
not supported.
21
B. Video Setup
Camera Type in Analog-CAM
Camera Type in IP-CAM
B-1. Resolution
Click drop down list to change the resolution of connecting device.
B-2. Quality
Click drop down list to change the image quality. For this 9ch model, the total bits per second should not be over 36Mbps.
B-3. FrameRate
Click drop down list to change the frame rate of connecting device.
C. IPCam Image Setup
Camera Type in Analog-CAM
Camera Type in IP-CAM
22
C-1. Display
Use the mouse to enable or disable the camera display on the screen or not.
C-2. Switch Dwell
Press ◄ or ► to change auto switch second. The value is between 0~99 sec.
C-3. Title
Use the mouse to setup the title of connecting IP device.
C-4. Contrast
Press ◄ or ► to change contrast level. The adjustment value is between 0~255
C-5. Brightness
Press ◄ or ► to change brightness level. The adjustment value is between 0~255
C-6. Hue
Press ◄ or ► to change hue level. The adjustment value is between 0~255
C-7. Saturation
Press ◄ or ► to change saturation level. The adjustment value is between 0~255
C-8. Sharpness
Press ◄ or ►/ mouse wheel to change sharpness level. The adjustment value is between 0~15
D. Motion Setup
Camera Type in Analog-CAM
D-1. Relay Dwell
Press ◄ or ► to change the relay time or disable relay function.
D-2. Buzzer Dwell
Press ◄ or ► to change the buzzer time or disable buzzer function.
D-3. Motion Detection
Click the checkbox to decide enable or disable motion detection.
D-4. Sensitivity
Press ◄ or ► to change sensitivity level.
D-5. Motion Area Setup
Press to setup motion area.
23
Camera Type in IP-CAM
D-6. Relay Dwell
Press ◄ or ► to change the relay time or disable relay function.
D-7. Buzzer Dwell
Press ◄ or ► to change the buzzer time or disable buzzer function.
D-8. Area1 Sensitivity
Press ◄ or ► to change the sensitivity of setup motion area in Area1. Click “Motion Area Setup” and drag a blue area for motion detection.
D-9. Area2 Sensitivity
Press ◄ or ► to change the sensitivity of setup motion area in Area2. Click “Motion Area Setup” and drag a green area for motion detection.
D-10.Area3 Sensitivity
Press ◄ or ► to change the sensitivity of setup motion area in Area3. Click “Motion Area Setup” and drag a red area for motion detection.
After dragging an area, right-click the mouse, select “Exit with saving” to complete the area setup. Select “Enable All” to set up global motion detection.
24
Select “Clean All” to clean the area of the current color in the view.
Select “Exit Without Saving” to go back to motion setup menu and the setting
you just changed will not be saved.
E. Privacy Setup
Camera Type in Analog-CAM
Camera Type in IP-CAM
E-1. Area1
Tick the “Area1” box and click “Area Setup” to drag a blue area for masking.
E-2. Area2
Tick the “Area1” box and click “Area Setup” to drag a green area for masking.
E-3. Area3
Tick the “Area1” box and click “Area Setup” to drag a red area for masking.
F. Audio Setup
The channel ticked means the sound from camera will be recorded into the playback video. Vise versa. No sound will be recorded in the playback video of the channel which is not ticked. It supports at most 4CH audio record.
25
G. Quick Setup
Other than “IPCAM Setup”, you can choose another way to complete the IP camera connection job: using Quick Setup.
G-1 Key in information manually
Here is the all-channel list. You can key in the IP address, port, and user name & password of the IP camera, and then assign the channel number. Tick “Enable” to connect with the IP camera.
G-2 IPCAM Quick Search
With Quick Search, you need not type the IP address. Click “IPCAM Quick Search” to enter the search menu.
The machine searches for all the IP devices under the LAN and list here. Find the IP camera you want to connect with, assign a channel number for it, and
26
tick “Enable” so that this IP camera will be added to the all-channel list. Back to the all-channel list, you can key in the user name and password, and tuck “Enable” to connect with the camera. If you want to revise the IP setting of a camera, click “Edit”:
The IPCam has to be under the same LAN with DVR in order to connect successfully. Ex. If DVR IP address is 192.168.10.33, IP Cam IP address should be 192.168.10.X. You can edit IP Cam IP address here or on the IP Cam.
27
3.4 RECORD SETUP
A. Post-Alarm Record Time
Press ◄ or ► to switch the recording time of post-alarm. That’s the recording length when alarm is triggered.
B. Mobile Streaming Setup
Press on to record the streaming for mobile viewing.
C. Record Mode
Use the drop down list to switch the recording mode. There are manual, schedule and alarm trigger three varieties of mode.
Manual: C lick and button on the right bottom of live view ing to start and
stop the m anual record.
Schedule: Click the “Schedule Setup” button to set the schedule recording time.
Alarm trigger: When the alarm trigger is detected, it start recording as the alarm
setting.
28
3.5 ALARM SETUP
A.Alarm Trigger Setup
A-1. Alarm Auto Switch
Use the drop down list to switch the alarm auto switch. When the alarm is triggered, the screen will switch to full screen, split screen (9CH split screen) or disable.
A-2. Video Loss Detection
Use the drop down list to switch the video loss detection. When the video loss is detected, the alarm will trigger.
A-3. Ext Alarm Detection
Use the drop down list to switch the Ext Alarm Detection. When the external
alarm is detected, the alarm will trigger.
A-4. Ext Alarm Mode
Choose normally open or normally close according to the external devise type.
A-5. HDD Temp. Warning
Use the drop down list to turn on or off the HDD Temp. Warning. When the HDD temperature is too high, the alarm will trigger.
B. Alarm Output Setup
This control item separates into two parts, “Buzzer Time” and “Relay Time”. User can
29
press ◄ or ► to switch ext. alarm buzzer time and video loss buzzer time in “Buzzer Time” option. The adjustment value is from 5 to 99 seconds. Moreover, among “Relay Time” option, the user can press ◄ or ► to switch ext. alarm relay time and video loss relay time. The adjustment value is from 5 to 99 seconds as well.
C. Alarm Event Setup
There are seven sort of events can be selected. When the selected items are happened and triggered, the event will be recorded in the event list.
30
3.6 NETWORK SETUP
A. IP ADDRESS SETUP
Press ◄ or ► to setup HYBRID DVR IP address.
A-1. IP Mode
Press drop down list to change IP mode to STATIC IP or DHCP.
A-2. IP Address
Use the virtual keypad to setup the HYBRID DVR IP ADDRESS.
A-3. Network
Use the virtual keypad to change SUBNET MASK.
A-4. Gateway
Use the virtual keypad to change Default GATEWAY.
A-5. DNS1
Use the virtual keypad to change DNS.
A-6. DNS2
Use the virtual keypad to change OTHER DNS.
A-7. WebPage Port
Use the virtual keypad to change the IE browser port.
31
B. PPPoE SETUP
B-1. PPPoE Setting
Press the drop down list to enable or disable PPPoE.
B-2. User Name
Insert the user name (ADSL account) which provided from local ISP.
B-3. Password
Insert the password which provided from local ISP.
B-4. Password Confirm
Insert the password again to confirm the password.
B-5. State
Present the current status of PPPoE function.
B-6. Send Mail After Dialed
Click the drop down list to enable or disable the function.
B-7. Subject
Insert the mail subject when dialed successfully.
C. DDNS SETUP
C-1. DDNS Enable
Click the checkbox to enable or disable DDNS function.
C-2. Provider
Click the drop down list to select DDNS provider.
C-3. Host Name
Insert the registered host name in the selected provider.
C-4. User Name
Insert the registered user name in the selected provider.
C-5. Password
Insert the registered password in the selected provider.
C-6. Update Interval
A period of time to update IP address.
C-7. State
32
The state after apply for DDNS. Updating: Information update. Idle: Stop service. DDNS registered successfully, now log by http://<username>.ddns.camddns.com: Registered successfully. Updating Failed, the name is already registered.
Updating Failed, please check your internet connection.
D. MAIL SETUP
D-1. Enable
Tick “Alarm” to send video to the mail address when external alarm is triggered. Tick “Motion” to send video to the mail address when motion detection is triggered.
D-2. Mail Server
The IP address of Mail Server
D-3. SMTP Port
The port of SMTP (known as Simple Mail Transfer Protocol). (Default value is
25)
D-4. User Name
The user name while log in to the mail server.
D-5. Password
The password while log in to the mail server.
D-6. Sender’s Mail
The sender’s account when send the mail via this mail server.
D-7. Receiver’s Mail
The receiver’s mail address.
D-8. BCC Mail
The receiver’s mail address for Bcc Mail.
D-9. Subject
The subject while sending the mail.
33
E. FTP SETUP
E-1. Enable
Use the checkbox to enable or disable FTP Server.
E-2. FTP Server
The IP address of FTP Server.
E-3. User Name
The username while log in to the ftp server.
E-4. Password
The password while log in to the ftp server.
E-5. FTP Port
The port number of file transmission. (Default value is 21)
E-6. Path
The ftp path where the user wants to reserve the information.
F. DHCP Server Setup
F-1. Enable
Use the checkbox to enable or disable DHCP Server function. When the function is activated, the HYBRID DVR can be treated as the DHCP server. The HYBRID DVR will assign or distribute one of the IP address which is according to the setup IP address range (start and end IP Address.) to the connecting IPCAM (setup DHCP function as well).
F-2. Start IP Address
Use the virtual keypad to insert the start IP Address of DHCP server.
F-3. End IP Address
Use the virtual keypad to insert the end IP Address of DHCP server.
F-4. Lease Time
Press ◄ or ► to change the lease time of DHCP server.
G. UPNP Port Forwarding Setup
34
G-1. Enable
Use the checkbox to enable or disable UPNP port setup.
G-2. External HTTP Port
Use the virtual keypad to insert the external http port.
G-3. External RTSP Port
Use the virtual keypad to insert the external rtsp port.
H. Network Streaming Setup
For Network Viewing, the Hybrid DVR provides two compression formats.
H-1. Main Streaming
Users view the H.264 video playback via Internet browser. Selecting the option can save the disk space while spend more time when loading the video.
H-2. Sub Streaming
Other than the original H.264 video, the Hybrid DVR saves a copy of M-JPEG video used for Network Viewing. If it takes long time when loading the video on the web, selecting sub streaming here may make it faster. However, to store both the H.264 and M-JPEG video, more disk space must be consumed.
35
3.7 AUTHORITY SETUP
A. HDD Format
Use the checkbox to enable or disable the authority of HDD Format function. If enable this function, the user has to insert password while performing HDD format.
B. Anonymous User Login
Use the checkbox to enable or disable the authority of anonymous user login. If enable this function, the user does not have to insert the username/ password and can view the live image via IE browser.
C. Password Protection
Use the checkbox to enable or disable the authority of password protection.
D. Keyboard Lock
Use the checkbox to enable or disable the operation of control bar which is in the right hand side of live view. The control bar can not work when keyboard lock is activated.
E. User Management
Among this item, user can setup the user management permission and the user authority management.
E-1. Permission
Use the mouse to click the checkbox to modify and alter the user authority.
36
E-2. Add User
After click button, the setup page will present in the following.
The user can distribute the authority and the permission for the new user.
37
3.8 DISK MANAGEMENT
A. Overwrite Mode
Click the drop down list to enable or disable overwrite function.
B. Hard Disk Full Warning
Click the drop down list to change value to 20/ 15/ 10 or 5% with non-overwrite mode. When LEFT RATIO is below the setting, it will enable AUDIBLE ALARM (If AUDIBLE ALARM of BUZZER of ALARM SETUP is ON).
C. C. Auto Deletion
Select “ON”, then on the playback list, users cannot find the recording data that is
older than the reserve day. For example, it’s 2012/10/19 17:40 now. Auto deletion is set as on, and reserve day is set as 3. The recording data which recording time is order than 2012/10/16 17:40 will not be indicated on the playback menu.
D. Reserve Day
Use ◄ or ► to setup the reserve day between 1~30 days.
Note: If the “Overwrite Mode” is set OFF and DVR keeps recording, the HDD will finally get full regardless that “Auto Deletion” is ON.
E. Storage Information
The information of storage device will present in this page.
38
F. Format HDD
Insert the user name and password while performing HDD format function.
39
3.9 SYSTEM SETUP
A. System Name
Use the virtual keypad to insert the name of the HYBRID DVR.
B. System ID
Use ◄ or ► to setup the HYBRID DVR ID. The adjustment value is between 0~32
C. Language
Use the drop down list to change the HYBRID DVR language. Currently, there are English, Traditional Chinese and Simplified Chinese three options.
D. Date Format
Use the drop down list to change DATE. There are DD/MM/YYYY, YYYY/MM/DD and MM/DD/YYYY three modes.
E. Version
The firmware version of the HYBRID DVR will show in this column.
F. Software Update
Click button to perform firmware updating.
G. Configure Setup
Click the checkbox to select which item can be setup by the user. The user can also load the setting to factory default, load the configure from USB and backup configure to USB.
40
H.Time Setup
Click button within “Time” block can adjust and synchronize the time of the HYBRID DVR as the system time of the PC. Moreover, if the user clicks the
enable checkbox and button within the NTP Setup block, the time of the HYBRID DVR will synchronize as the NTP Server.
I. Day Light Saving Time
After enable the daylight saving time function, the user can use the drop down list to select the start time and the end time of daylight saving time. After complete the
setting, please click button to reserve the setting.
J. Status Display Setup
Use the mouse to click the options, which is including “Date and Time Display”, “Record Information Display”, “Camera Title Display” , and “Camera IP Display”.
41
K. Monitor Adjust
User can use ◄ or ► to adjust the monitor related setting within this page, there are “Brightness”, “Contrast”, “Hue” and “Saturation” four options can be set. You can also
adjust Resolution here by selecting “1280*720”, or “1920*1080(HDMI) / 1280*1024(VGA).” The video output interface, HDMI or VGA, affects the resolution options.
42
3.EX DEBUG MESSAGE
The purpose of the following procedure is to export a HDD debug message file. If user has problems with the DVR, the technical person can analysis the file and might find the cause of problem.
Plug in a USB disk. Enter the Authority Setup page and make sure the option “HDD Format (Require
Password Confirmation)” is ticked.
Enter the Disk Setup page. Click “Format HDD”.
Key in “@k” in the user name column to login. No password is required.
The screen turns to Advance Setup page. Click download. It takes about 10 seconds to
export the file.
43
When the downloading is complete, a message pops up to remind the user. Click”
OK”.
Now the debug message file should have been in your USB disk. Please turn the file”
dbgms.tar” to Linkcom’s technical person.
4 HYBRID DVR PLAYBACK
Note: Under playback mode, it will output sound when switch to full screen mode. A. RECORD BACKUP
With playback mode, press this button to backup record (.ha0 video backup) and press this button again to finish backup. For performing the single image backup (.jpg single
image backup), press first and then click this button to backup the necessary image.
B. AUDIO VOLUME
Press this button, and the audio volume control board will pop up.
C. DISPLAY CONTROL
Within playback mode, use display control to switch the camera channel.
D. DIGITAL ZOOM
In the live full screen mode, left-click the button of the mouse to pull a range to zoom in or zoom out the image. User can right-click the button of the mouse to disable this function. (NOTE: Using the mouse to operate digital zoom can zoom in to max. 16 times.) Moreover, user can also use ZOOM key on the front panel to perform this function. (First, click ZOOM Key and then click ▲▼◄► key to select zoom in or zoom out position. Finally, click ENTER key to complete the setting. Moreover, click ZOOM Key again can disable digital zoom function. Using the panel key to perform zoom in function is fixed at 2 times.)
E. RECORD AND PLAYBACK CONTROL
Same as front panel controller and remote controller.
44
45
4.1 TIME SEARCH
Select the start of playback time and then click button to playback the recorded data. If the time contains the recorded data, the time point within this page will become red.
4.2 EVENT SEARCH
After entry to the event search page, user can click the event log item which shown on the
list to start playback. Moreover, the user could click button to select the specific event option to filter the event option that shown on the list.
46
4.3 BACKUP
After click the backup button, the user could use drop down list to select the storage device, USB/ DVD-RW and the backup time selection mode, Time Mode/ Hours Mode. After that, click button to start backup.
TIME MODE
Click ◄ or ► to select the start and end backup time.
Moreover, among “Select Channel” option, use the mouse to select the channel which is going to backup.
47
4.4 SYSTEM LOG
System log is reserved all of the system record. The maximum storage quantity is 2000. Click button to perform the further data filter action. After complete the specific item selection, please click button to reserve the setting.
While return to the system log page, it will only reveal the specific selection items.
After click button
48
5 BACKUP PLAYBACK
SYSTEM REQUIREMENT
CPU: Intel Celeron 1.6G MEMORY: 256MB. VGA: 32MB VGA RESOLUTION: 1024 x 768. OS: Windows XP / 2000 or above
SUGGESTED REQUIREMENT
CPU: Intel P4 2.8G MEMORY:512MB or above VGA:64MB or above VGA RESOLUTION:1024 x 768 OS: Windows XP / 2000 or above NETWORK BANDWIDTH: Upload Speed is 256kbps or above
5.1 MAIN SCREEN SETTING
The player (D6Viewer.exe) is used to play the DVR backup video. D6Viewer.exe can be obtained via the Internet; moreover, while performing USB backup and DVD-RW backup, the software will be built automatically as well.
A. MAIN SCREEN
Open the D6Viewer. Use Overlay mode can improve the system resource performance.
Select video source
Playback Control
Save as AVI
Time & Event Search
Channels Divide Screen
Channel Selected
49
B. HDD PLAY
1. Remove the DVR HDD and connect it to the PC. The DVR HDD is Linux format, so the Windows system may not know it. Please use the software “Ext2Fsd” to assign a drive letter to the HDD. “Ext2Fsd” is in the attached CD or can be downloaded from the Internet. Start the Ext2Fsd, and it will detects all the disks connected with your PC.
Right-click on the DVR HDD and choose “Change Drive Letter”.
Click “Add”
Assign a letter to the HDD, then click OK so that the HDD get the letter and can
be recognized by the Windows.
50
2. Under HDD play mode, select the DVR HDD to load the video file in the HDD.
C. File Play
1. You can use D6Viewer to open a single video backup file. Under file play mode, select "Open".
51
2. Choose the path that the .haX file is reserved and pick the file to playback.
3. Press the play icon to play the video or still picture.
5.2 PLAYBACK OPERATION
A. TIME SEARCH
Select the Date and Time and then click to play the film.
B. EVENT SEARCH
It will display all the events which are reserved within the DVR HDD after press
(Shown in the following) and double click left button of mouse to
trigger event.
52
C. LOG
Click to check the log records.
D. ZOOM
Tick the “Zoom” box and drag an area on the screen. Click the area to zoom in.
53
E. BACKUP FILE TO AVI
1. Please select specific channel to backup.
2. During video playback mode please press AVI bottom to start.
3. Make up a filename and path than press bottom to start AVI backup.
4. Press AVI bottom to finish backup.
54
6 NETWORK VIEWING & PLAYBACK
SYSTEM REQUIREMENT
CPU: Intel Celeron 1.6G MEMORY: 256MB. VGA: 32MB VGA RESOLUTION: 1024 x 768. OS: Windows XP / 2000
SUGGESTED REQUIREMENT
CPU: Intel P4 2.8G MEMORY:512MB or above VGA:64MB or above VGA RESOLUTION:1024 x 768 OS: Windows XP / 2000
NETWORK BANDWIDTH: Upload Speed is 256kbps or above
6.1 IP ADDRESS SETUP ON PC SITE
Install cameras inside in LAN or use network cable to connect with PC. This is for
IPInstallerEng.exe to set up IP address of cameras. If OS is Windows XP SP2 or above, the following Windows Security Alert will popup. Then, please click on Unblock.
Then, IPInstallerEng.exe will popup: HYBRID DVR default IP address is 192.168.1.220
55
NOTE: Please input correct network parameters without blank spaces.
On Device Lists, it lists all servers. Click on one server and then its IP setting will show on the right side. After editing the parameters and clicking on Submit, the following dialogue box will popup. And, it will reboot the device with new parameters.
56
6.2 OPTIONAL MICROSOFT INTERNET EXPLORER SETUP OPTION 1: DISABLE ACTIVEX WARNING
A. IE Tools Internet Options Security Custom Level Security Settings
Download unsigned ActiveX controls Enable or Prompt (recommend).
B. IE Tools Internet Options Security Custom Level Security Settings
Initialize and script ActiveX controls not marked as safe Enable or Prompt (recommend).
1
2
3
4
5
Above three options are all based on select as the prompt.
As indicated in the dialogue box. Please select "YES."
57
OPTION 2: ADD TO TRUSTED SITES
IE Tools Internet Options Security Trusted sites Sites
58
6.3 LOGIN
A. INSTALL ACTIVEX
B. START INSTALL ACTIVEX
C. ACCOUNT & PASSWORD LOGIN
After IP setup and connect to network or LAN, type IP address on IE Browser directly. The following User name & Password Login window will popup.
Default user name: admin Default password: admin
6.4 REMOTE CONTROL
LIVE VIEW
PTZ PANEL
The 4-direction arrows are used to shift the camera view. The bigger value you select in "Speed", the longer the moving range becomes by
each click on the arrow. If you click the house icon , the camera view turns to initial position. Use magnifier icons to zoom in / zoom out .
After you adjust the camera view to where you want to set a preset point, select a number from "Preset Point" drop-down menu, and click "Save" button to add the point to the reset point list. When you select that point from the drop-down menu and click "Go", the camera view will move to
System Time
Live Page
Configuration Page
Play Back
Record
Video Backup
59
Screen Format
Change Language
60
where you had set. Click the button to start auto-pan, click the button to pause.
1
RECORD
Click to start record the current live video to the PC or storage device. The saved file is *.ha0 file.
PLAYBACK
Click and select time playback or event playback.
A. HDD Select
User can select HDD1 or HDD2 for playback
B. Playback Time
User can select the time then press “Time Search” for playback.
C. Time Search
User can select the time then press “Time Search” for playback.
D. Event Search
HDD Select
Event Search
Playback Time
Time Search
61
User can select event item by pressing “Event Search” for playback.
62
BACKUP
Click to select backup time point. The saved file is *.ha0 file.
First, select Start and End backup time which have to among the Record Time.
Then, click Save button to select the position on PC where the user is going to
backup the data. After that, press OK button to start the backup.
Finally, double-click the left button of the mouse to open the saved backup file. The
backup file will named as the time when start to backup, such as, (20080526113258.ha0) will be 2008/05/26 11:32:58.
OTHER FUNCTIONS
Right-click the on any channel, and the menu pops up:
A. Snapshot:
User can save any single picture from image.
B. Performance:
User can select image quality (high, medium & low)
C. Use Overlay:
User can use Overlay function. The function can save system resource and promote the efficacy.
D. Play audio:
User can play audio function by channel. Note: remote user can receive audio from DVR. However, there’s no influence on
63
sound recording of playback video whether the audio is played or not.
6.5 CONFIGURE
A-1. System - Information
DVR Name: This name will show on the IP Installer. MAC Address: The MAC address cannot be revised.
Time Zone: The time zone can only be modified on local DVR.
NTP Server: The NTP Server IP address can only be modified on local DVR.
A-2. System – Software Update
System Update: Click on the “Browse” button to select the firmware file and then
press “Upgrade” button to upgrade the firmware. ActiveX Updating: The ActiveX control should be also updated when you update the DVR/NVR firmware. Use the tool in the attached CD to uninstall the old ActiveX control so that the newest version can be registered.
Automatic Uninstall
Please follow the steps:
1. After updating the DVR/NVR firmware, close the web browser.
2. Run the file "unreg" in the CD to automatically remove the existing ActiveX component "WATCH_16R" from your PC.
3. Log in the DVR/NVR via web browser again, and the browser will require
you to install the new version of ActiveX control.
Manual Uninstall
If the tool does not work, please follow the steps to uninstall ActiveX control manually.
1. Look for the files "KConfig.ocx" and "WATCH_16R.ocx" in one of the possible paths: "C:\WINDOWS\Downloaded Program Files"
64
"C:\WINDOWS\W16R" "C:\WINDOWS\system32\WATCH_16R"
2. "Start" -> "Run" -> Key in: regsvr32(The path of KConfig.ocx) /u -> Click "OK" Ex.: regsvr32 C:\WINDOWS\system32\WATCH_16R\KConfig.ocx /u
3. "Start" -> "Run" -> Key in: regsvr32(The path of WATCH_16R.ocx) /u ->
Click "OK"
Ex.: regsvr32 C:\WINDOWS\system32\WATCH_16R\WATCH_16R.ocx /u
4. Log in the DVR/NVR via web browser again, and the browser will require
you to install the new version of ActiveX control.
Load Setup from Default: Click “Apply” to reset the machine and revert all setting back to default value. Load Setup from: Click “Browse” to choose a file. You can load setup from your computer if you ever clicked “Download” and saved the settings before. Backup Setup: Click “Download” to save a current setting file to PC. You can apply this file to other DVR so that the setting will be copied to other DVR.
A-3. System – Daylight Saving Time
Give the start and end daylight saving time. During daylight saving, the time will be 1 hour faster.
65
66
A-4. System – Status Display
Select the items that will be displayed on local DVR.
A-5. System – System Setup
DVR ID: The ID is used for distinguish DVRs when you use remote controller or
RS485. Give different ID when you have several DVRs.
Date Format: Select a format of date display.
B-1. Camera – Camera Setup
Analog Camera:
After connecting the analog camera to DVR, select “Analog Camera” of corresponding channel.
IP Camera, Normal Mode:
Under Normal mode, Http protocol is used to access camera. You can key in IP address, port, username, and password manually. You can either use IP Installer to scan the LAN and find the camera:
67
Click “Edit” to revise the device information. Click “Use” to add this device to channel.
IP Camera, RTSP Mode:
Under RTSP mode, Rtsp protocol is used to access camera. Give the IP address, port, username, password, and RTSP path of two streaming.
B-2. Camera - Video Setup
Analog Camera:
Select the channel, and adjust the resolution quality, and frame rate.
IP Camera:
Select the channel, and adjust the resolution quality, and frame rate.
68
B-3. Camera – Image Setup
Analog Camera:
Adjust image contrast, brightness, hue, saturation, and sharpness here. “Dwell Time” means the swap interval when performing swap on single channel screen.
IP Caemra:
Adjust image contrast, brightness, hue, saturation, and sharpness here. “Dwell Time” means the swap interval when performing swap on single channel screen.
69
B-4. Camera – Motion Setup
Analog Camera:
Enable motion function, and drag on the screen the motion area. When motion is detected in the area, the DVR will be triggered and execute alarm action. Relay Dwell: The value determines the relay triggering time when motion detection happens. Buzzer Dwell: The value determines the buzzer sounding time when motion detection happens.
IP Camera:
Enable motion function, and drag on the screen the motion area. You can setup three areas. When motion is detected in the area, the DVR will be triggered and execute alarm action. Relay Dwell: The value determines the relay triggering time when motion detection happens. Buzzer Dwell: The value determines the buzzer sounding time when motion detection happens.
70
B-5. Camera – Mask Setup
Analog Camera:
Enable mask function, and drag on the screen the mask area. Decide the mask color. The area will be covered with selected color on live screen and playback video.
IP Camera:
Enable mask function, and drag on the screen the mask area. You can setup three mask area. The area will be covered with black on live screen and playback video.
B-6. Camera – Audio Setup
Select the channel, and enable or disable the audio recording. No sound will be recorded in the playback video of the channel that audio setup is not enabled. It supports at most 4CH audio recording.
71
C-1. Record – Record Setup
Alarm Recording Time: When an event happens, the DVR can record the video at
event timepoint, and send it to mail or FTP. Adjust the recording video length. Mobile Record: Enable it, and DVR will record the streaming for mobile viewing, so that you can view playback video on mobile phone.
Record Mode: Manual, Alarm-trigger, or schedule recording.
C-2. Record – Schedule Record
Select the tag on the bottom of calendar, and click on the calendar to draw color. Red stands for full recording, yellow stands for alarm triggering recording, and green stands for no recording. Click “Apply”. If you select “Schedule” in record mode option, the DVR will records video as this schedule.
D-1. Alarm – Alarm Trigger
HDD. Temp. Warning: Enable it to make DVR alarm when the HDD temperature is
higher than the temperature the user sets. Alarm Auto Switch: Select to switch to split screen or single channel when motion detection happens. Video Loss Detect: Enable it to make DVR alarm when camera is disconnected and video is lost.
Ext. Alarm Detect: Enable it to make DVR alarm when external alarm is triggered. Ext. Alarm Pole: Normally open or normally closed. Select as the external device
you connect.
72
D-2. Alarm - Alarm Output
Adjust the buzzer sounding time and relay triggering time when external alarm is triggered or video loss happens.
D-3. Alarm – Alarm Event
When the events happen, the event log will be recorded in the event list. Enable the event item that you want to record in the event list.
E-1. Ethernet – IP Address
IP Setup: Set up the DVR IP information. Select DHCP to get IP address from
DHCP server or select Static to fill in the IP address manually. UPnP Port Forwarding: When the DVR is under a router, you can use port forwarding to allow the WAN connection. Fill in the http port and rtsp port and check your router setting.
73
E-2. Ethernet – PPPoE
To use PPPoE, fill in the username and password of your ADSL account. The IP address will be displayed in “IP address” column after PPPoE is dialed successfully. If you enable the option “send mail after dialed”, DVR will send mail to your mail account after PPPoE is dialed successfully. “Subject” is the subject of mail.
E-3. Ethernet – DDNS
Some DDNS provider requires users to apply for an account before using their DDNS service, for example, dyndns.org. If you select dyndns.org, you should go to their website, and apply with your username and password, the website will return with a hostname to you.
Fill in the hostname, username, and password that you applied to dyndns.org, and give the update time. After clicking “Apply”, check the state to see if you apply DDNS successfully. The DDNS address should be displayed in state column.
Some DDNS provider do not require users to apply for an account before using their DDNS service, for example, ddns.camddns.com. If you select ddns.camddns.com, please key in the username as you want.
74
Fill in the username that you want, and give the update time. After clicking “Apply”, check the state to see if you apply DDNS successfully. The DDNS address should be displayed in state column.
E-4. Ethernet – Mail
Tick “Alarm” to send video to mail when external alarm is triggered. Tick “Motion” to send video to mail when motion detection is triggered. Fill in the mail server information, including mail server address, SMTP port, username, and password. If the server asks for secure connection, select TLS or SSL connection way. Then, fill in the sender and receiver’s mail address and mail subject.
E-5. Ethernet – FTP
Tick “Alarm” to upload video to FTP when external alarm is triggered. Tick “Motion”
to upload video to FTP when motion detection is triggered. Fill in the FTP server information including the server address, FTP data port,
75
username, and password. Give the path that you want to save the video.
E-6. Ethernet – DHCP
When the function is enabled, the DVR is as an DHCP server and able to assign IP address to IP camera. Give the Start IP and End IP for DHCP. Key in lease time here to decide the frequency that the IP address is renewed.
F-1. Authority – Authority Setting
HDD Format Password Check: Enable the option, then DVR will ask for password
when users want to format HDD. Anonymous Login: Enable the option, then user can access the DVR via web browser and watch live screen without password. Disable the function, then password is necessary to access the DVR. Password Protection: Enable the option, then user has to log in to operate the local NVR.
F-2. Authority – User Setup
Add User: In the pop up window, set up the username and password for the new user.
The administrator can give authority to the new user by tick at the choice below. (Ex. Ticking at “PTZ” allows the new user to control the PTZ). In “Masking Channels in Playback and Network”, you can tick those channels that you don’t want to show to this user. This user will not see live view or playback video of that channel.
76
Modify: Click “Edit”, and fill in username and password to edit the user authentication or password.
Remove: Click “Remove” to remove the user.
G-1. Disk – Disk Setup
Overwrite Mode: Enable the function, and the data will be overwritten after the
HDD is full. Hard Disk Full Warning: When the HDD space is smaller the setting, The buzzer will sound to remind users. Auto Deletion: Select “ON”, then on the playback list, users cannot find the recording data that is older than the reserve day.
Reserve Day: Setup the reserve day between 1~30 days.
G-2. Disk – Disk Information
77
It shows HDD information of DVR.
H-1. Player
Click the button to download D6Viewer, the DVR
recording file player.
Click the button to download D6Viewer, the DVR
78
79
APPENDIX A: RECORDING TIME LAPSE (HOURS)
2TB U N IT ：H ours
IM A G E Q U A L IT Y
(M bps)
LO W (0.25M )
M ED IU M (0.5M )
STA N D A R D (1M )
H IG H (1.5M )
A V ER A G E
A V ER A G E
A V ER A G E
A V ER A G E
16CH
960
480
240
160
4TB U N IT：H ours
IM A G E Q U A L IT Y
(M bps)
LO W (0.25M )
M ED IU M (0.5M )
STA N D A R D (1M )
H IG H (1.5M )
A V ER A G E
A V ER A G E
A V ER A G E
A V ER A G E
16CH
1920
960
480
320
6TB U N IT：H ours
IM A G E Q U A L IT Y
(M bps)
LO W (0.25M )
M ED IU M (0.5M )
STA N D A R D (1M )
H IG H (1.5M )
A V ER A G E
A V ER A G E
A V ER A G E
A V ER A G E
16CH
2880
1440
720
480
8TB U N IT：H ours
IM A G E Q U A L IT Y
(M bps)
LO W (0.25M )
M ED IU M (0.5M )
STA N D A R D (1M )
H IG H (1.5M )
A V ER A G E
A V ER A G E
A V ER A G E
A V ER A G E
16CH
3840
1920
960
640
* The value is for reference only
80
APPENDIX B: HDD COMPATIBLE TABLE
Brand
Model
Capacity
others
SEAGATE
ST380815AS
80 GB
7200 10
ST3160815AS
160 GB
7200 10
STM3250820AS
250 GB
7200 10
ST3250310SV
250GB
SV35.3
ST3400620AS
400 GB
7200 10
ST3500320SV
500GB
SV35.3
ST3500410SV
500GB
SV35.5
ST3500320AS
500GB
7200 11
ST3500418AS
500GB
7200 12
ST3500312CS
500GB
Pipeline HD .2
ST3750640AS
750 GB
7200 10
ST3750330AS
750 GB
7200 11
ST31000333AS
1TB
7200 11
ST31000340AS
1TB
7200 11
ST31000340NS
1TB
Barracuda ES.2
ST31000340SV
1TB
SV35.3
ST31000322CS
1TB
Pipeline HD .2
ST31000525SV
1TB
SV35.5
ST31000524AS
1TB SATA3
7200 12
ST1500DL003
1.5TB SATA3
Barracuda LP
ST31500341AS
1.5TB
7200 11
ST32000542AS
2TB
Barracuda LP
ST3320620AS
320 GB
7200
ST3500413AS
500GB
7200
ST3500320NS
500GB
7200
WD
WD1600AAJS
160 GB
7200 CB
WD2500AAKS
250 GB
7200 CB
WD2500AVVS
250 GB
7200 GP
WD3200AVVS-73L2B0
320GB
7200 GP
WD5000AACS
500 GB
7200 GP
WD5000AVVS
500 GB
7200 GP
WD5000AAKS
500GB
7200 CB
81
WD5002ABYS
500GB
7200 RE
WD
WD5000AAKX
500GB SATA3
Caviar Blue
WD5000AUDX
500GB SATA3
Green Power
WD6400AAKS
640 GB
7200 BLUE
WD6400AVVS
640 GB
7200 GP
WD7500AACS
750GB
7200 GP
WD7500AVVS
750GB
7200 GP
WD10EACS
1TB
7200 GP
WD10EADS
1TB
Caviar Green
WD10EVDS
1TB
Green Power
WD10EVVS
1TB
7200 GP
WD10EARS
1TB
Caviar Green
WD10EALX
1TB SATA3
Caviar Blue
WD10EURX
1TB SATA3
Green Power
WD15EADS
1.5TB
7200 GP
WD15EARS
1.5TB
7200 GP
WD15EURS
1.5TB
7200 GP
WD5000AVDS-63U7B0
1.5TB
7200 GP
WD15EVDS
1.5TB
7200 GP
WD20EADS
2.0TB
7200 GP
WD20EVDS-63T3B0
2.0TB
7200 GP
WD20EARS
2.0TB
Caviar Green
WD20EURS
2.0TB
7200 GP
WD30EURS
3TB
CE-GP
WD30EZRX
3TB
7200
HITACHI
HDS721616PLA380
160 GB
7200
HDT725025VLA380
250 GB
7200
HDT725032VLA360
320 GB
7200
HDP725050GLA360
500 GB
7200
HCP725050GLA380
500GB
7200
HDT721010SLA360
1TB
7200
HDS721010CLA332
1TB
7200
HDS722020ALA330
2TB
7200
HDS721050CLA362
500GB
7200
82
APPENDIX C: ERROR MESSAGE LIST
ERROR MESSAGE
ERROR STATUS & REASON
NOTE
DISK ACCESS ERROR!
H.D.D. Data structure Un-normal. Data does not record into HYBRID DVR or bad sector on HYBRID DVR H.D.D. Please install another H.D.D. and perform the record again.
UPDATE FILE ERROR!
Please re-download the update file and update again.
FIRMWARE UPGRADE FAILED
Please reboot the HYBRID DVR and upgrade the firmware. Please send the HYBRID DVR back to repair when HYBRID DVR is disability.
MEDIA ACCESS FAIL!
The USB file format is incorrect (Please format the pen drive to FAT32) or Pen Drive is setup to ONLY READ mode (Please annul ONLY READ mode) when reserve the data by using Pen Drive. The data cannot be burn into CD/DVD disc. Please change another CD/DVD disc and backup the file in CD/DVD disc storage.
NO FILE!
There is no upgrade file within Pen Drive or the name of upgrade file does not correspond with HYBRID DVR format. Please adjust the upgrade file name based on the following information. 16CH -> UpdateR.bin 08CH -> Update8.bin 04CH -> Update4.bin
USB DEVICE NOT FOUND NO USB
Pen Drive undetected. Please Unplug the Pen Drive and plug it again.
BACKUP START TIME ERROR
Backup start time error. BACKUPEND TIME ERROR
Backup end time error.
DISK ERROR
The data cannot be burn into CD/DVD disc. Please change another CD/DVD disc and backup the file.
FAN FAILED
Fan Error Warning.
NO LOG DATA
No Events Record.
SCHEDULE RECORD
The condition is caused by trying to stop recording when perform the schedule record. Please setup the record to manual mode and then stop the record.
83
PLEASE SELECT ONE CAMERA
The message will be shown while using the ZOOM function under split screen condition. Please switch the screen into full screen mode and then operate the ZOOM function.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use