liniLED PCB Photon, PCB Photon 4000, PCB Photon 2000, PCB Photon 1200, PCB Photon 3000 Series Manual
LED strip manual
C
liniLED® PCB Photon
F
RoHS
IP00
R
BEND RADIUS
20 mm
V D
24
CRI
80
MAC
2
ADAM
+
S D C M
LED strip PCB Photon
General
Handling
Installation
Operation and use
Cleaning and maintenance
Environment and waste
Warning
Area advice
Product dimensions
Product information
Product specications
Cable selection
Product care and handling
Cutting instructions
Soldering
Connect IP00
Power supply
Symbols
4
4
4
4
4
4
5
5
5
5
6
7
9
10
11
12
13
14
Technical notes
Read the instructions and safety precautions before installation, usage and storage of the products to secure safety of the user and reliability of the product.
- Hand over the instructions to the end user and those responsible for installation and usage.
- Triolight B.V. cannot be held responsible for improper handling, product installation, usage or storage.
Handling
- Handle with care.
- The product may not be modi ed or converted otherwise than prescribed.
- Products are transported in proper packaging. Products should remain packed until installation.
- Take ESD (Electrostatic Discharge) protection measures when handling liniLED® products.
- The products and their components may not be exposed to mechanical, static loads and other tension/compression other than from the product itself.
Installation
- Attention: The power has to be switched o the main power supply or the connection before installation. Not doing so may damage the product.
- Use a suitable LED power supply/driver: 24 V DC constant voltage. Do not drive the product on other voltages than described in their datasheet/products
speci cations.
- Installation has to be done by a certi ed professional with knowledge of electrical circuits or a specialised maintenance person known with valid directives.
- General and local construction-, safety- and installation regulations should be respected.
- Use only supplied parts, accessories and required tools as prescribed in the installation manual to guarantee a safe installation and use of the product.
- Products may solely be installed in the areas according to their prescribed IP-rating, IK-rating, temperature range and chemical resistances.
- The LED strip should be installed on an adequate cooling body for proper heat dissipation to ensure smooth operation and long lifetime.
- Do not fasten anything on the product, same applies for hanging.
- Do not install the product in the following cases:
- Damage is visible on the product or its cables.
- The inside of the product is moistened or dirty.
- The product or its cables have been modi ed. It could lead to an electrical shock or a short circuit may occur.
- Children may not play unsupervised with electrical products as they cannot judge the dangers in dealing with electrical circuits correctly.
- Use proper mounting surfaces when installing in environments with large variations in temperature and operating lengths more than 2m. This should
absorb the stress of any mismatch in expansion.
Operation and use
Solely use the product when its working correctly. If not, switch the power o immediately and advise an electrical specialist in the following cases:
- Damage is visible on the product and/or the product does not function.
- The product is overheating and/or smoke or steam rises from the product.
- Crackling sounds are noticeable.
- Repairs on the installation may only be performed by quali ed electricians. Product repairs may solely be done by Triolight B.V.
Cleaning and maintenance
- Attention: Disconnect the power before maintenance and cleaning.
- Dust and dirt accumulated over time should be removed from the light emitting surface to assure optimal functioning of the product.
- Paints, solvents and corrosive cleaning chemicals may not contact and thus a ect the product.
Environment and waste
- Exterior decorative lighting should only be used after sunset.
- This product may not be treated as household waste. Dispose of the material through the waste recycling of electrical and electronic equipment.
Warranty
This product comes with a 2 year warranty. Warranty void if:
- The installation guide has not been consulted (installation mistake).
- The installation is not done by a certi ed installer.
- Local rules and guidelines are not respected.
- The invoice cannot be shown and/or has been altered.
- Damage is caused by negligence, abnormal use or improper handling, use, maintenance and/or cleaning of the product.
LED strip manual | liniLED® PCB Photon
4
Area advice
Depending on the area where the liniLED® LED strip is installed we oer a range of solutions to cope with external factors. The product portfolio
for the liniLED® PCB LED strip only includes a range of IP00 connectors.
Indoor environment (IP00) | liniLED® PCB Connector set
Product code: 11808
Product dimensions
LED strip top view
100
LED strip front view
1/2.2
8
Indoor environment (IP00)
Solder
8
LED strip manual | liniLED® PCB Photon
5
Product information
The liniLED® LED strip PCB Photon (IP00) is a high quality, exible LED strip with an outstanding eciency. Thanks to the small dimensions, the
PCB LED strip is ideal to use in small spaces (indoor use only!). With 3M double sided tape on the back, the PCB LED strip is easy to mount. The
liniLED® LED strip PCB Photon serie is available in various white colours and lumen (1200-4000).
* Connect the PCB LED strips with the PCB Connector Set and the PCB Inline Connector. See datasheet for more information.
Product specications
Photon 1200Photon 2000Photon 3000Photon 4000
Colour
2000K
2400K
2700K
3000K
4000K
6500K
Colour
2000K
2400K
2700K
3000K
4000K
6500K
Colour
LED/m
70
70
70
70
70
70
LED/m
70
70
70
70
70
70
LED/m
V DC
24
24
24
24
24
24
V DC
24
24
24
24
24
24
V DC
W/m
10.6
10.6
8.9
8.9
8.1
8.1
W/m
17.9
17.9
15
15
13.6
13.6
W/m
lm/m
1002
1170
1208
1230
1221
1223
lm/m
1536
1709
1742
1798
1831
1813
lm/m
Temp ˚C
-30...55
-30...55
-30...55
-30...55
-30...55
-30...55
Temp ˚C
-30...55
-30...55
-30...55
-30...55
-30...55
-30...55
Temp ˚C
Max. Length
9 m
9 m
9 m
9 m
9 m
9 m
Max. Length
4.5 m
4.5 m
4.5 m
4.5 m
4.5 m
4.5 m
Max. Length
B50/L70
> 50.000 h
> 50.000 h
> 50.000 h
> 50.000 h
> 50.000 h
> 50.000 h
B50/L70
> 50.000 h
> 50.000 h
> 50.000 h
> 50.000 h
> 50.000 h
> 50.000 h
B50/L70
2000K
2400K
2700K
3000K
4000K
6500K
Colour
2000K
2400K
2700K
3000K
LED strip manual | liniLED® PCB Photon
6
70
70
70
70
70
70
LED/m
70
70
70
70
24
24
24
24
24
24
V DC
24
24
24
24
28.9
28.9
23.7
23.7
21.8
21.8
W/m
28.9
28.9
28.9
28.9
2292
2545
2631
2785
2663
2614
lm/m
3300
3401
3415
3404
-30...55
-30...55
-30...55
-30...55
-30...55
-30...55
Temp ˚C
-30...55
-30...55
-30...55
-30...55
3 m
3 m
3 m
3 m
3 m
3 m
Max. Length
3 m
3 m
3 m
3 m
> 50.000 h
> 50.000 h
> 50.000 h
> 50.000 h
> 50.000 h
> 50.000 h
B50/L70
> 50.000 h
> 50.000 h
> 50.000 h
> 50.000 h
The liniLED® LED strips need a minimum voltage at the beginning of the LED strip to function according to the speci cations. The table below gives an indication
of the maximum cable length based on the cable thickness and power supply voltage. The connection between the cable and LED strip is with a
liniLED® Connector.
In case the required length is larger than the length mentioned in this table, the supply voltage is di erent or if a detailed wire plan with
branches is planned, please contact your distributor for a detailed cable calculation.
9 m
9.83 m
12.94 m
14.85 m
24.80 m
30.76 m
34.44 m
Cable Selection Photon 1200
The liniLED® LED strips need a minimum voltage at the beginning of the LED strip to function according to the speci cations. The table below gives an indication
of the maximum cable length based on the cable thickness and power supply voltage. The connection between the cable and LED strip is with a
liniLED® Connector.
In case the required length is larger than the length mentioned in this table, the supply voltage is di erent or if a detailed wire plan with
branches is planned, please contact your distributor for a detailed cable calculation.
Cable X information LED strip Max. cable length 2000, 2400K Max. cable length 2700, 3000K Max. cable length 4000, 6500K
@ 24 V DC @ 24 V DC @ 24 V DC@ 25V DC @ 25V DC @ 25V DC
liniLED® cable (2 x 0.50 mm)
0.035 Ω/m
liniLED® cable (2 x 0.75 mm)
0.023 Ω/m
liniLED® cable (2 x 1.00 mm)
0.018 Ω/m
liniLED® cable (2 x 1.50 mm)
0.012 Ω/m
liniLED® cable (2 x 2.50 mm)
0.007 Ω/m
Cable Selection Photon 2000
Cable X information LED strip Max. cable length 2000, 2400K Max. cable length 2700, 3000K Max. cable length 4000, 6500K
1 m
2 m
5 m
9 m
1 m
2 m
5 m
9 m
1 m
2 m
5 m
9 m
1 m
2 m
5 m
9 m
1 m
2 m
5 m
27.95 m
13.33 m
4.56 m
1.96 m
42.04 m
20.05 m
6.86 m
2.95 m
55.90 m
26.66 m
9.12 m
3.92 m
84.09 m
40.11 m
13.72 m
5.91 m
139.96 m
66.76 m
22.84 m
54.85 m
26.78 m
9.94 m
4.95 m
82.51 m
40.29 m
14.95 m
7.45 m
109.70 m
53.56 m
19.88 m
9.90 m
165.02 m
80.58 m
29.91 m
14.90 m
274.64 m
134.10 m
49.78 m
33.53 m
16.12 m
5.68 m
2.58 m
50.45 m
24.25 m
8.54 m
3.88 m
67.07 m
32.25 m
11.36 m
5.17 m
100.90 m
48.51 m
17.08 m
7.77 m
167.92 m
80.74 m
28.44 m
65.57 m
32.14 m
12.08 m
6.14 m
98.64 m
48.35 m
18.18 m
9.24 m
131.14 m
64.29 m
24.17 m
12.28 m
197.28 m
96.71 m
36.36 m
18.48 m
328.33 m
160.95 m
60.52 m
36.97 m
17.84 m
6.36 m
2.96 m
55.62 m
26.84 m
9.57 m
4.46 m
73.95 m
35.69 m
12.73 m
5.93 m
111.24 m
53.69 m
19.15 m
8.92 m
185.14 m
89.35 m
31.88 m
72.17 m
35.44 m
13.40 m
6.87 m
108.57 m
53.32 m
20.16 m
10.34 m
144.35 m
70.89 m
26.81 m
13.75 m
217.15 m
106.64 m
40.33 m
20.69 m
361.40 m
177.48 m
67.13 m
@ 24 V DC @ 24 V DC @ 24 V DC@ 25V DC @ 25V DC @ 25V DC
liniLED® cable (2 x 0.50 mm)
0.035 Ω/m
liniLED® cable (2 x 0.75 mm)
0.023 Ω/m
liniLED® cable (2 x 1.00 mm)
0.018 Ω/m
liniLED® cable (2 x 1.50 mm)
0.012 Ω/m
liniLED® cable (2 x 2.50 mm)
0.007 Ω/m
LED strip manual | liniLED® PCB Photon
7
1 m
2 m
3 m
4.5 m
1 m
2 m
3 m
4.5 m
1 m
2 m
3 m
4.5 m
1 m
2 m
3 m
4.5 m
1 m
2 m
3 m
4.5 m
16.02 m
7.37 m
4.48 m
2.56 m
24.11 m
11.09 m
6.74 m
3.85 m
32.05 m
14.74 m
8.97 m
5.12 m
48.22 m
22.18 m
13.49 m
7.71 m
80.26 m
36.91 m
22.46 m
12.83 m
31.95 m
15.33 m
9.79 m
6.10 m
48.07 m
23.07 m
14.73 m
9.18 m
63.91 m
30.67 m
19.59 m
12.20 m
96.14 m
46.14 m
29.47 m
18.36 m
160.01 m
76.79 m
49.05 m
30.55 m
19.37 m
9.04 m
5.60 m
3.30 m
29.14 m
13.60 m
8.42 m
4.97 m
38.75 m
18.09 m
11.20 m
6.61 m
58.29 m
27.21 m
16.85 m
9.95 m
97.02 m
45.29 m
28.05 m
16.55 m
38.38 m
18.55 m
11.93 m
7.53 m
57.74 m
27.90 m
17.95 m
11.32 m
76.77 m
37.10 m
23.87 m
15.06 m
115.48 m
55.81 m
35.91 m
22.65 m
192.19 m
92.88 m
59.78 m
37.71 m
21.50 m
10.10 m
6.31 m
3.77 m
32.34 m
15.20 m
9.49 m
5.68 m
43.00 m
20.21 m
12.62 m
7.55 m
64.69 m
30.41 m
18.98 m
11.37 m
107.67 m
50.62 m
31.60 m
18.92 m
42.46 m
20.59 m
13.30 m
8.43 m
63.88 m
30.97 m
20.00 m
12.69 m
84.93 m
41.18 m
26.60 m
16.87 m
127.76 m
61.95 m
40.01 m
25.38 m
212.64 m
103.10 m
66.59 m
42.25 m
The liniLED® LED strips need a minimum voltage at the beginning of the LED strip to function according to the speci cations. The table below gives an indication
of the maximum cable length based on the cable thickness and power supply voltage. The connection between the cable and LED strip is with
a liniLED® Connector.
In case the required length is larger than the length mentioned in this table, the supply voltage is di erent or if a detailed wire plan with branches is planned,
please contact your distributor for a detailed cable calculation.
Cable selection Photon 3000
The liniLED® LED strips need a minimum voltage at the beginning of the LED strip to function according to the speci cations. The table below gives an indication
of the maximum cable length based on the cable thickness and power supply voltage. The connection between the cable and LED strip is with
a liniLED® Connector.
In case the required length is larger than the length mentioned in this table, the supply voltage is di erent or if a detailed wire plan with branches is planned,
please contact your distributor for a detailed cable calculation.
Cable X information LED strip Max. cable length 2000, 2400K Max. cable length 2700, 3000K Max. cable length 4000, 6500K
@ 24 V DC @ 24 V DC @ 24 V DC@ 25V DC @ 25V DC @ 25V DC
liniLED® cable (2 x 0.50 mm)
0.035 Ω/m
liniLED® cable (2 x 0.75 mm)
0.023 Ω/m
liniLED® cable (2 x 1.00 mm)
0.018 Ω/m
liniLED® cable (2 x 1.50 mm)
0.012 Ω/m
liniLED® cable (2 x 2.50 mm)
0.007 Ω/m
1 m
2 m
3 m
1 m
2 m
3 m
1 m
2 m
3 m
1 m
2 m
3 m
1 m
2 m
3 m
9.43 m
4.07 m
2.29 m
14.19 m
6.13 m
3.44 m
18.87 m
8.15 m
4.58 m
28.39 m
12.26 m
6.89 m
47.26 m
20.41 m
11.46 m
19.30 m
9.01 m
5.57 m
29.04 m
13.55 m
8.39 m
38.61 m
18.02 m
11.15 m
58.08 m
27.10 m
16.78 m
96.66 m
45.11 m
27.93 m
11.79 m
5.25 m
3.07 m
17.73 m
7.90 m
4.62 m
23.58 m
10.50 m
6.14 m
35.47 m
15.80 m
9.25 m
59.04 m
26.30 m
15.39 m
23.82 m
11.26 m
7.08 m
35.83 m
16.95 m
10.65 m
47.64 m
22.53 m
14.16 m
71.67 m
33.90 m
21.31 m
119.28 m
56.42 m
35.47 m
12.93 m
5.82 m
3.45 m
19.45 m
8.76 m
5.19 m
25.86 m
11.64 m
6.90 m
38.90 m
17.52 m
10.39 m
64.75 m
29.16 m
17.29 m
26.01 m
12.36 m
7.81 m
39.12 m
18.59 m
11.75 m
52.02 m
24.72 m
15.62 m
78.25 m
37.19 m
23.50 m
130.24 m
61.90 m
39.12 m
Cable selection Photon 4000
Cable X information LED strip Max. cable length 2700 t/m 6500K
liniLED® cable (2 x 0.50 mm)
0.035 Ω/m
liniLED® cable (2 x 0.75 mm)
0.023 Ω/m
liniLED® cable (2 x 1.00 mm)
0.018 Ω/m
liniLED® cable (2 x 1.50 mm)
0.012 Ω/m
liniLED® cable (2 x 2.50 mm)
0.007 Ω/m
1 m
2 m
3 m
1 m
2 m
3 m
1 m
2 m
3 m
1 m
2 m
3 m
1 m
2 m
3 m
@ 24 V DC @ 25V DC
9.43 m
4.07 m
2.29 m
14.19 m
6.13 m
3.44 m
18.87 m
8.15 m
4.58 m
28.39 m
12.26 m
6.89 m
47.26 m
20.41 m
11.46 m
19.30 m
9.01 m
5.57 m
29.04 m
13.55 m
8.39 m
38.61 m
18.02 m
11.15 m
58.08 m
27.10 m
16.78 m
96.66 m
45.11 m
27.93 m
LED strip manual | liniLED® PCB Photon
8
Product care and handling
20 mm
20 mm
Maximum bending radius is 20 mm. Solely bend up- or downwards.
Do not bend the LED strip sidewards.
Do not compress or stretch the LED strip.
Do not twist the LED strip.
The LED strip has to be unreeled on a horizontal surface at the time of installation. Do not unreel the spool of LED strip before installation.
LED strip manual | liniLED® PCB Photon
9
Cutting instructions
Work in an ESD protected environment. Make use of an anti-static
strap.
Top view | Make sure the cut is vertical as illustraded in the image
above.
Turn o the power before cutting the LED strip.
Top view | Only cut on the dotted lines to prevent damaging the LED
strip.
Dispose of the unnecessary material through waste recycling of
electrical and electronic equipment.
LED strip manual | liniLED® PCB Photon
10
0.5 mm
2
8 mm
Solder
Work in an ESD protected environment. Make use of an anti-static
strap and use lead-free solder.
Solder the wires to the PCB. We advise to use a cable with an area not
bigger then 0.5 mm
Turn o the power. Make sure the wires are not under electric
current.
Pre-solder the connector pads.
350 C
Pre-solder the wires.
LED strip manual | liniLED® PCB Photon
11
350 C
Solder the wires to the connector pads.
350 C
5 mm
Connect IP00
Remove tape protection from back. Peel o tape carefully from the
PCB and fold the rst 5 mm.
Press connector rmly untill it clicks.
Make sure the PCB and connector are at on the surface and insert
PCB into connector.
Finished product.
In order to maintain adequate electrical contact, the
connectors are designed for single use. Remove is possible
but will result in the destruction of the connector.
LED strip manual | liniLED® PCB Photon
12
Use a at screwdriver to open the connector.
Power supply
liniLED® Cable 1 m
L
N
Power Supply
24 V DC
-+
230 V AC
Cable X
Control
IP00
Turn o the power before connecting the LED strip to the power
supply.
Connect the LED strip as indicated in the gure above. The wires should be connected as follows: Red (+) and Black (-).
Insert the power plug.
LED strip manual | liniLED® PCB Photon
13
Symbols
V DC
F
RoHS
IP00
R
20 mm
BEND RADIUS
24
Electro Static Discharge (ESD) sensitive device, apply standard ESD precautions when handling the product
Manufacturer’s declaration that the product meets the applicable EC directives.
Suitable for mounting on all surfaces and suitable to cover with insulating material.
Restriction of Hazardous Substances (RoHS): product complies with the RoHS directive and each homogeneous material does
not exceed the limits for the materials mentioned under the RoHS directive (Pb, Hg, Cd, Cr6+, PBB and PBDE).
Not protected against ingress of solid foreign objects. Not-protected against ingress of water.
Bending of the LED strip is possible with a radius of ≥ 20millimetres in the specied direction.
Current Voltage. 24 Volt.
CRI
80
MAC
ADAM
S D C M
Electrical appliance class III: this product is designed to be supplied from an extra-low voltage
(≤ 60.0 V DC or ≤ 42.4 V AC).
The CRI value of this product is 80 or higher.
+
The binning tolerance of this product is 2 MacAdam.
2
LED strip manual | liniLED® PCB Photon
14
Subject to misprints, errors and modications. No legal rights can be derived from this document. V0319
liniLED® is a registered trademark of Triolight B.V.
Loading...