FCC ID: 2ARI5-MB1001
MagBar User Manual
Contents
Compatibility Notice
Package Includes
Quick Guide
Specs
Warranty
Exclusion
Important
Customer Support
FCC Warning
Compatibility Notice
1
1
2
8
9
9
10
The PITAKA MagBar will only wirelessly charge Qi
supported phones with a proper PITAKA MagCase (Pro),
including MagCase (Pro) for iPhone 8/8 Plus/X/Xs/XR/Xs
Max and Samsung Galaxy S10e/S10/S10+/S9/S9+/S8/S8+/S7
edge.
Your phone cannot be attached on the MagBar when you
use an other case or stick metal plates on your phone.
Do not use the MagBar to charge your wireless charging
devices that are not Qi-compatible.
Installation Guide
1, Choose a proper position on the wall to install the
MagBar.
2, Attach the MagBar wall mount to the wall and mark
the four holes on the wall with a pencil.
Notice: If you are installing the MagBar to concrete/brick wall, it’s
recommended to use a 6mm-diameter drill and the recommended
drilling depth is 30mm;
If you are installing the MagBar to wood/ plasterboard wall, it’s
recommended to use a 2mm-diameter drill and the recommended
drilling depth is 5mm.
4, Hammer the expansion bolt into the wall hole. Make
sure they are flushed with the wall surface.
10
11
Notice: Make sure the side without the arrow is faced to the wall
and the arrow is faced up.
5, Align the wall mount hole with the punching position.
Keep the side with the arrow face to the user and the
arrow should face up. Use a screwdriver to install the
screws and fasten the wall mount.
If you are not using the PITAKA MagCase. You can
Notice:
attach the metal plate (Included in the package. Scan
below QR code for the alignment paper to help with
locating the metal plate.) to the back of your phone case
or phone to be compatible with it. But we strongly
recommend you to use MagCase together with MagBar
to optimize the seamless carrying experience. Use the
code “PITAKA10” (expires after Dec 31, 2019) to get a 10%
discount for your MagCase now.
Package Contains
6, Align the MagBar with the wall mount and buckle up
the two. Press down the MagBar and slide it to the left.
Then MagBar Installation is completed.
MagBar x 1 Wall Mount x 1 Charger x 1
Dual Type C Cable x 1 Screws x 6 Expansion Bolt x 6
User Manual
User Manual x 1
Metal Plate x 2
1 2 3 4 5
3, Use a percussion drill to punch the holes in the
position where the marks are previously marked.
Notice: If you are installing the MagBar to wood/ plasterboard wall,
you can just skip this step.
Using Guide
Step1: Plug one end of the charging cable into
any charging port on the left or right of the
MagBar.
Step 2: Plug the other end of the charging
cable into the charger.
6 7 8 9 10 11 12
Step 3: The mobile phone can be wirelessly
charged by being placed on the wireless
charging area.
Step 4: Freely attach your everyday carry
essentials on the MagBar, including the keys,
AirPodPal, etc.
Specs Warranty
The PITAKA MagBar is warranted for 12 months from the
Item Specification
Rated Input Voltage
Rated Input Current
Rated Output Voltage
Rated Output voltage
Transmission Distance
Transfer Efficiency
Operating Temperature
Storage Temperature
Working Frequency
11mm
382mm
5V~9V
3A
DC 5V/1A
DC 9V/1.1A
≤ 8mm
75% Max
-10℃~30℃
-20℃~60℃
125KHz
107mm
date of purchase.
The MagBar is warranted to be free defects in materials
and function under regular use for the lifetime of the
product. A defect is defined as an imperfection or flaw
that is produced by a manufacturing error, including
malfunction of wireless charging or surface defect, etc.
This warranty is non-transferable and covers only the
original end-user purchaser. PITAKA will only authorize
the warranty claim if the product was purchased from
the official store or authorized dealer.
MODIFICATION: Any change or modification of this device
will void the warranty
Exclusion
Damages don’t cover those resulting from abuse, not
correctly maintained, alteration or misuse (including
disassemble, drops), abnormal wear and tear, cosmetic
damages that do not affect the functionality.
Important
Read all instructions and warnings before using this
product. Improper use may result in product damage,
excess heat, toxic fumes, fire or explosion, for which
damages PITAKA is not responsible.
1. In order to achieve the best charging effect, please
place your device at the correct position to charge.
2. This charger is only suitable for indoor use, beware of
rain and exposure.
3. Please use the original charger to charge or other
adapter with output over 30W.
4. Avoid placing metal objects in the working area when
charging, and do not let the charger drop off or put
heavy objects on it.
5. It is recommended to unplug or turn off the power
after charging is completed.
6. Please never connect power supply to your MagBar
with the both sides Type C connectors at the same time.
Improper operation resulting in the malfunction of the
MagBar is the sole responsibility of the purchaser.
Customer Support
Phone：+852 9202 6223
E-mail: support@ipitaka.com
Website: www.ipitaka.com
FCC WARNING
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
(2) this device must accept any interference received,
including interference that may cause undesired
operation. Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
RF Exposure: A distance of 15 cm shall be maintained between the antenna and users, and the
transmitter may not be co‐located with
any other transmitter or antenna.
-- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV
technician for help.
The device has been evaluated to meet the general RF
exposure requirement.
FCC ID: 2ARI5-MB1001
Loading...