Package Contains:
PITAKA New MagMount Qi *1
Charging Cable *1
User Manual*1
Compatibility Notice:
The PITAKA New MagMount Qi will only wirelessly
charge any Qi supported phones with a proper PITAKA
MagCase (Pro).
Wireless charging may not work when you put other
cases or stick metal plates on your phone.
Do not use the New MagMount Qi to charge your
wireless charging devices that are not Qi-compatible
wirelessly.
Quick Guide
Step 1: Connect the cable to the New MagMount Qi’s
USB port and your car charger’s USB port. Plug the car
charger into your car’s power outlet.
Step 2: Install the New MagMount Qi on your car
1，Installing the PITAKA Car Vent New MagMount Qi
Find a safe location on the vehicle vent, slide the New
MagMount Qi air vent clips into your car’s air vent.
2， Installing the Suction Cup New MagMount Qi
Find a proper location on the windshield or the dashboard,
and clean the surface. Then firmly press the suction cup
and press down the suction switcher to ensure the New
MagMount Qi is adhered tightly to the windshield or
dashboard.
*Notice: Remember to press the suction cup on the
windshield FIRST, then press the suction switcher and lock
to ensure that you have tightly adhered the New
MagMount Qi to the windshield.
2.1 Firmly press the suction cup against the windshield.
a) Push down the suction switcher to lock the mount in
place.
2.3 Then the MagMount Qi is attached on the windshield
tightly.
3. Installing the CD Slot MagMount Qi
Simply insert the slot mount and tighten the screw to
lock it in place
3.1 Insert the mount in the CD slot
3.2 Tighten the mounting screw to lock the mount in
place.
3.3 Then MagＭount Qi (CD Slot) is installed well
New MagMount Qi User Manual
1 2
Notice: A dashboard pad is needed when you attach
it on your car’s dashboard.
3 4 5 6 7
8
9
Step 3: Attach your compatible phone on the vent mount. The
vent mount starts charging your phone immediately and
holds securely.
Step 4: You can adjust the ball-joint rotation of the vent
mount, so your device is in either portrait or landscape
orientation. And then tighten the rotation to fix the position
until it rests firmly.
ROTATE 360
10 11 12 13 14 15 16 17
Spec
Items specification
Input Voltage 5V ~9V
Input Current ≤2A
Rated Output Voltage/ Current
(Normal charging)
Rated output voltage/ current
(Fast charging)
Max Output Power 10W
Transmission Distance ≤5mm
Transfer Efficiency 75% Max
Operating Temperature -10℃~30℃
Storage Temperature -20℃~60℃
Working Frequency 110KHz-205KHz
DC 5V/1A
DC 9V/1.1A
2.3072
3.0768
Note: Fast charging will only be supported when using a
QC 3.0 adapter with an output over 18W and a USB cable
supporting 3A power output.
2.8154
Warranty
The PITAKA MagMount Qi is warranted for 12 months
from the date of purchase. The MagMount Qi is
warranted to be free defects in materials and function
under normal use for the lifetime of the product. A
defect is defined as an imperfection or flaw that is
produced by a manufacturing error, including
malfunction of wireless charging or surface defect, etc.
This warranty is non-transferable and covers only the
original end-user purchaser. PITAKA will only authorize
the warranty claim if the product was purchased from
the official store or authorized dealer.
MODIFICATION：Any change or modification of
this device will void the warranty.
Exclusion
Damages don’t cover those resulting from abuse, not
correctly maintained, alteration or misuse (including
disassemble, drops), abnormal wear and tear, cosmetic
damages that do not affect the functionality.
Important
Read all instructions and warnings before using this
product. Improper use may result in product damage,
excess heat, toxic fumes, fire or explosion, for which
damages PITAKA is not responsible.
1) DO NOT DIRECT HEATED AIR FROM THE VENT ONTO
THE MOUNT WHILE IT IS ATTACHED TO THE VENT. When
running the car’s heater, make sure you close the vent
that the mount is attached to or take the mount from the
car vent directly, or direct the heated air out of the car’s
lower vents and away from the upper vents.
2) Do not keep the MagMount Qi in a high-temperature
environment, including heat caused by intense sunlight
or other forms of heat. Do not place it in the fire or other
excessively hot environments.
3) Do not disassemble the New MagMount Qi or attempt
to modify it in any way.
4) Do not attempt to power the New MagMount Qi with
any connection other than the Type-C connector.
5) Do not attempt to replace any part of the New MagMount
Qi.
6) All products have gone through a thorough quality
assurance inspection. If you find that your New MagMount
Qi is excessively hot, is emitting odor, is deformed, abraded,
cut or is experiencing or demonstrating an abnormal
phenomenon, immediately stop all product use and contact
Manufacturer.
7) If this New MagMount Qi is intended by the purchaser to
be used by a minor, purchasing adult agrees to provide
detailed instructions and warnings to any minor before use.
Failure to do so is the sole responsibility of the purchaser,
who agrees to indemnify Manufacturer for any unintended
use/misuse by a minor.
Customer Service
Phone：+852 9202 6223
E-mail: support@ipitaka.com
Website: www.ipitaka.com
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation. Any
changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician
for help.
The device has been evaluated to meet the general RF
exposure requirement.
FCC ID: 2ARI5-CM3001Q
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Loading...