LINEAR TECHNOLOGY LTC3577 Technical data

L DESIGN IDEAS
LTC3577/LTC3577-1
INPUT
POWER
LOGIC
CONTROL
SEQUENTIAL
BUCK
I2C
CONTROLLED
LED DRIVER
ADAPTER
5V
V
OUT1
OVP
5V
PC USB
MICRO
POWER ON
4.2V/4.1V
V
OUT
V
OUT2
V
OUT3
MICROCONTROLLER
MEMORY
I2C
CONTROLLED
LDO1
LDO2
CODEC/DSP
PERIPHERAL POWER
I/0
LCD BACKLIGHTING
STATUS
PUSHBUTTON
I2C BUS
CC/CV
All-in-One Power for Portables: Single IC Replaces Battery Charger, Pushbutton Controller, LED Driver and Five Voltage Regulator ICs
Introduction
The LTC3577/LTC3577-1 integrates a number of portable device power management functions into one IC, reducing complexity, cost and board area in handheld devices. The major functions include:
q
Five voltage regulators to power
memory, I/O, PLL, CODEC, DSP or a touch-screen controller
q
A battery charger and
PowerPath™ manager
q
An LED driver for backlighting
an LCD display, keypad and/or buttons
q
Pushbutton control for
debouncing the on/off button, supply sequencing and allowing end-users to force a hard reset when the microcontroller is not responding
By combining these functions, the LTC3577/LTC3577-1 does more than just reduce the number of re­quired ICs; it solves the problems of
Figure 1. Portable device power distribution block diagram featuring the LTC3577/LTC3577-1
34
34
functional interoperability—where otherwise separate features operate together for improved end-product performance. For instance, when the power input is from USB, the limited input current is logically distributed among the power supply outputs and the battery charger.
The LTC3577/LTC3577-1 offers other important features, including PowerPath control with instant-on operation, input overvoltage protection for devices that operate in harsh envi­ronments and adjustable slew rates on the switching supplies, making it pos­sible to reduce EMI while optimizing efficiency. The LTC3577-1 features a
4.1V battery float voltage for improved battery cycle life and additional high temperature safety margin, while the LTC3577 includes a standard 4.2V battery float voltage for maximum battery run time.
by Marty Merchant
Pushbutton Control
The built in pushbutton control cir­cuitry of the LTC3577/LTC3577-1 eliminates the need to debounce the pushbutton and includes power-up sequence functionality. A PB Status output indicates when the pushbutton is depressed, allowing the micropro­cessor to alter operation or begin the power-down sequence. Holding the pushbutton down for five seconds produces a hard reset. The hard reset shuts down the three bucks, the two LDOs and the LED driver, allowing the user to power down the device when the microprocessor is no longer responding.
Battery, USB, Wall and High Voltage Input Sources
The LTC3577/LTC3577-1 is designed to direct power from two power supply inputs and/or a Li-Ion/Polymer bat­tery. The V input current limit control, designed to deliver 100mA or 500mA for USB applications, or 1A for higher power applications. A high power voltage source such as a 5V supply can be connected via an externally controlled FET. The voltage control (VC) pin can be used to regulate the output of a high voltage buck, such as the LT3480, LT3563 or LT3505 at a voltage slightly above the battery for optimal battery charger efficiency.
Figure 1 shows a system block dia­gram of the LTC3577/LTC3577-1. An overvoltage protection circuit enables one or both of the input supplies to be protected against high voltage surges. The LTC3577/LTC3577-1 can provide power from a 4.2V/4.1V Li-Ion/Poly­mer battery when no other power is available or when the V rent limit has been exceeded.
Linear Technology Magazine • December 2009
input has selectable
BUS
input cur -
BUS
Battery Charger
C1 22µF
6.3V
C4 10µF 25V
C3 10µF 25V
D1
BAT54S
C2
10µF
25V
R1 301k
R2
21.5k
L1 10µH LPS4018-103M
V
BOOST
12V 35mA
V
BOOST
–12V 35mA
DN470 F02
I
LED_FS
V
OUT
2.7V TO 5.5V
I
LED
LED_OV
SW
LTC3577/
LTC3577-1
L2
47nH
IFC-0805-47
D2 BAT54S
The LTC3577/LTC3577-1 battery charger can provide a charge current up to 1.5A via V when available. The charger also has an automatic recharge and a trickle charge function. The battery charge/ no-charge status, plus the NTC status can be read via the I2C bus. Since Li-Ion/Polymer batteries quickly lose capacity when both hot and fully charged, the LTC3577/LTC3577-1 reduces the battery voltage when the battery heats up, extending battery life and improving safety.
or wall adapter
BUS
DESIGN IDEAS L
Figure 2. Dual polarity boost converter
Three Bucks, Two LDOs and a Boost/LED Driver
The LTC3577/LTC3577-1 contains five resistor -adjustable step-down regulators: two bucks, which can pro­vide up to 500mA each, a third buck, which can provide up to 800mA, and two LDO regulators, which provide up to 150mA each and are enabled via the I2C interface. Individual LDO supply inputs allow the regulators to be connected to low voltage buck regula­tor outputs to improve efficiency. All regulators are capable of low voltage operation, adjustable down to 0.8V.
The three buck regulators are se­quenced at power up (V then V
) via the pushbutton con-
OUT3
troller or via a static input pin. Each buck can be individually selected to run in Burst Mode operation to opti­mize efficiency or pulse-skipping mode for lower output ripple at light loads.
OUT1
, V
OUT2
A patented switching slew rate control feature, set via the I2C interface, allows the reduction of EMI noise in exchange for efficiency.
The LTC3577/LTC3577-1 LED boost driver can be used to drive up to 10 series white LEDs at up to 25mA or be configured as a constant voltage boost converter. As a LED driver, the current is controlled by a 6-bit, 60dB logarithmic DAC, which can be further reduced via internal PWM control. The LED current smoothly ramps up and down at one of four different rates. Overvoltage protection prevents the internal power transistor from dam­age if an open circuit fault occurs. Alternatively, the LED boost driver can be configured as a fixed voltage boost, providing up to 0.75W at 36V.
Many circuits require a dual polarity voltage to bias op amps or other analog devices. A simple charge pump circuit,
as shown in Figure 2, can be added to the boost converter switch node to provide a dual polarity supply. Two forward diodes are used to account for the two diode voltage drops in the inverting charge pump circuit and provide the best cross-regulation. For circuits where cross-regulation is not important, or with relatively light negative loads, using a single forward diode for the boost circuit provides the best efficiency.
Conclusion
The high level of integration of the LTC3577/LTC3577-1 reduces the number of components, required board real estate and overall cost of power systems for portable electronics. It greatly simplifies power path design with built-in solutions to a number of complex power flow logic and control problems.
L
LTM4619, continued from page 33
Multiphase Operation
For a 4-phase, 4-rail output volt­age system, use two LTM4619s and drive their MODE_PLLIN pins with a LTC6908-2 oscillator, such that the two µModule devices are synchronized 90° out of phase. Reference Figure 21 in the LTM4619 data sheet. Synchroniza­tion also lowers voltage ripple, reduc­ing the need for high voltage capacitors whose bulk size consumes board space. The design delivers four dif­ferent output voltage rails (5V, 3.3V,
2.5V and 1.8V) all with 4A maximum load.
Linear Technology Magazine • December 2009
Thermal Performance
Exceptional thermal performance is shown in Figure 5 where the unit is operating in parallel out­put mode; single 12VIN to a single
1.5VOUT at 8A. Both outputs tied together create a combined output current of 8A with both channels running at full load (4A each). Heat dissipation is even and minimal, yield­ing good thermal results. If additional cooling is needed, add a heat sink on top of the part or use a metal chassis to draw heat away.
Conclusion
The LTM4619 dual output µModule regulator makes it easy to convert a wide input voltage range (4.5V to
26.5V) to two or more 4A output voltage rails (0.8V to 5V) with high efficiency and good thermal dissipa­tion. Simplicity and performance are achieved through dual output voltage regulation from a single package, making the LTM4619 an easy choice for system designs needing multiple voltage rails.
L
3535
Loading...