2X2 Switcher For d
Model # HDMI-SW-2X2M
USER MANUAL
www.linearcorp.com
ASKING FOR ASSISTANCE
Technical Support:
Telephone (800) 421-1587
(760) 438-7000
Fax (760) 438-7199
Technical Support Hours:
6:30 AM - 4:30 PM PST Monday through Friday.
Email:
techsupport@linearcorp.com
Website:
www.linearcorp.com
Notice
Linear LLC reserves the right to make changes in the hardware, packaging
and any accompanying documentation without prior written notice.
© 2008 Linear LLC, All Rights Reserved
TABLE OF CONTENTS
Introduction / Operation Notes
1
Features
2
Panel Descriptions
3
Connecting and Operating the 2X2 Switcher For HDMI
4
RMT-2 Installation
5
IR Code Conicts
6
RS-232 Interface
7
Wiring Diagram
8
Specications
9
Warranty
10
INTRODUCTION
The Linear 2x2 Switcher for HDMI routes high denition video in multiple resolutions
up to 1080p plus multichannel digital audio from either one of two sources to the two
displays. Two outputs gives you the choice of sending high denition audio and video
signals to two displays simultaneously. A digital audio output port is available if you need
to direct the audio to an A/V receiver. The 2x2 Switcher for HDMI eliminates the need
to disconnect and reconnect sources to a display equipped with one input. It works with
Blu-ray and HD-DVD players, TiVo systems and satellite set top boxes that connect to
an HDMI display. By using the IR remote, either source is accessible at all times.
How It Works
You simply connect all your sources to the switcher’s HDMI inputs. Then connect up
to two displays on the switcher’s HDMI outputs. Once the sources, the Switcher and
the display(s) are powered and connected, you simply select which source you want
to view using the IR remote.
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE 2X2 SWITCHER FOR HDMI
Display information (EDID) is sent from the display connected to HDMI •
Output Port 1 to both of the sources connected to the 2X2 Switcher for
HDMI. If there is no display connected to HDMI Output Port 1, the EDID
from the display connected to HDMI Output Port 2 will be used. (See note
on page 4 for additional information)
The 2X2 Switcher for HDMI can only mirror one input video signal at a time to •
both display outputs. The user can choose which of the two HDMI inputs will be
displayed on both HDMI outputs
HDMI/HDCP compliant•
Compatible with all HDMI and DVI* displays•
NOTE: When used with a HDMI to DVI adapter.
1
FEATURES
Features
Switch easily between any two HDMI/DVI* sources •
Outputs are mirrored to two HDMI/DVI* displays simultaneously •
Supports resolutions up to 1080p, 2K and 1920 x 1200•
Additional digital optical audio output is extracted from the HDMI input for easy •
connection to multichannel A/V receivers
Inputs are switched• with either the provided IR remote control or RS-232 serial
control interface
Extends the range of HDMI compliant devices by equalizing and re-clocking the •
HDMI signal
HDMI/HDCP compliant •
Includes:
(1) 2X2 Switcher for HDMI
(2) 6 ft HDMI cables (M-M)
(1) 5V DC Power Supply
(1) RMT2-IR remote
(1) User’s Manual
NOTE: *When used with a HDMI to DVI Adapter
2
PANEL DESCRIPTIONS
Front Panel
HDMI
Input 1
Input LED
HDMI
Input 2
Indicator
Back Panel
HDMI
Output 1*
IR Eye
Extension Port
HDMI
Output 2
Digital Optical
Output
IR Eye
5V DC Power
Input
Power LED
Indicator
RS-232
Serial Control
Interface
*See note on page 4
3
CONNECTING THE 2X2 SWITCHER FOR HDMI
How to Connect the 2X2 Switcher For HDMI
Connect the supplied cable from the HDTV HDMI source into the HDMI input 1.
port 1 of the 2X2 Switcher for HDMI.
Connect the second HDTV HDMI source to HDMI input port 2 on the 2X2 Switcher 2.
for HDMI using a user supplied HDMI cable.
Connect the display(s) to the HDMI output port(s)* of the 2X2 Switcher for 3.
HDMI using user supplied cable(s).
Optionally, connect an external audio processor to the 2X2 Switcher for HDMI 4.
using a user supplied digital optical cable.
Plug the 5V DC power supply into the 2X2 Switcher for HDMI.5.
NOTE: *Display information (EDID) is sent from the display connected to HDMI
Output Port 1 to both of the sources connected to the 2X2 Switcher for HDMI. If
there is no display connected to HDMI Output Port 1, the EDID from the display
connected to HDMI Output Port 2 will be used. The source will output resolutions
and timings according the EDID that is being fed by the 2X2 Switcher for HDMI.
Therefore, all of the connected displays must be capable of accepting the timings
and resolution output by the source. It is recommended that the display with the
lowest native resolution be connected to HDMI output port 1. This is to ensure that
a compatible video signal will be able to be displayed on all connected monitors.
OPERATING THE 2X2 SWITCHER FOR HDMI
Switching between the inputs on the 2X2 Switcher for HDMI is done using either
the supplied RMT2-IR remote or through the RS-232 serial control interface.
IR Remote Control
Pressing button one on the remote will select the HDMI source that is connected to
HDMI input port one. Pressing two on the remote will select the HDMI source that
is connected to HDMI input port two.
RS-232 Serial Control Interface
Please see page 7 for more information on the RS-232 serial control interface.
4
RMT2-IR INSTALLATION
1. Remove battery cover from the back of the RMT2-IR remote.
2. Verify that dip switches 1 & 2 are in the down (OFF) position. (See page 6)
Insert the battery, hold the battery so that you can see the positive side facing up.
3.
The side that is not marked must be facing down.
4. Test the RMT2-IR remote by pressing ONLY one button at a time. The indicator
light on the remote will ash once each time you press a button.
WARNING: Do not press multiple buttons simultaneously and do NOT press buttons
rapidly. These actions will cause the remote to reset and steps 1-4 will have to be
repeated.
Note: The RMT2-IR ships with two batteries. One battery is required for operation,
the second battery is complimentary.
The optional IR extender allows you to
relocate your HDMI Switcher and still retain IR
control. Linear part# IR-EXTENDER
5
IR CODE CONFIGURATION
HowtoResolveIRCodeConicts
In the event that IR commands from other remote controls conict with the supplied RMT-2IR
remote control, changing the remote channel will alleviate this issue. The RMT-2IR remote control
and the 2X2 Switcher for HDMI have DIP SWITCHES for conguring the remote channel that
both units use to communicate. These settings must match each other for proper operation. The 2
DIP SWITCH bank on the RMT-2IR is located underneath the battery cover. The 8 DIP SWITCH
bank for the 2X2 Switcher for HDMI is located inside of the unit. *DIP SWITCH 1 and 2 on the
RMT-2IR correspond to DIP SWITCH 3 and 4 on the 2X2 Switcher for HDMI.
NOTE: *DIP SWITCHES 1, 2, and 5 through 8 are not used on the 2X2 Switcher for HDMI.
Because the procedure for changing channels requires the main unit to be disassembled, this
procedure should only be done if there are IR conicts present in your setup.
Disconnect power from unit before starting. Remove all cabling from unit.
To open the 2X2 Switcher for HDMI Unit, remove all screws from the sides and underside of the
unit. Remove the hex nuts above each HDMI connector and on the RS-232 serial connector. Slide
the unit apart carefully to expose the internal PCB and the 8 DIP SWITCH bank.
When DIP SWITCH adjustments are complete, carefully slide the unit back together. Being careful
not to over tighten the hex nuts, screw them back in above each HDMI connector and on the RS232 serial connector. Screw all of the screws from the sides and underside of the unit back into the
unit, again being careful not to over tighten the screws. Plug all cabling back into its proper location
on the unit. Reconnect power to the unit and test for IR conicts.
Remote
Remote Channel 1:
Default
Remote Channel 3:
Remote Channel 1:
Default
Remote Channel 3:
2X2 Switcher for HDMI
1234567
1234567
1 2
1 2
Remote Channel 2:
8
Remote Channel 4:
8
6
Remote Channel 2:
Remote Channel 4:
1234567
1234567
1 2
1 2
8
8
RS-232 SERIAL CONTROL INTERFACE
1 2 3 4 5
6 7 8 9
1 2 3 4 5
6 7 8 9
Only Pins 2 (RX), 3 (TX), and 5 (Ground) are needed to operate RS-232 Interface
Binary Table
ASCII Input Binary
1 1 0011 0001
2 2 0011 0010
3 3 0011 0011
4 4 0011 0100
Terminal Settings
Bits per second ................................................................................................. 19200
Data bits .................................................................................................................... 8
Parity .................................................................................................................. None
Stop bits .....................................................................................................................1
Flow Control ....................................................................................................... None
7
WIRING DIAGRAM
Maximum HDMI cable length is 15 ft at 1080P resolution without the use of an HDMI-SB or HDMI-CAT5-EXT
8
SPECIFICATIONS
Video Amplier Bandwidth .......................................................... 165 MHz
Input Video Signal ................................................................. 1.2 Volts p-p
Input DDC Signal ............................................................ 5 Volts p-p (TTL)
Single Link Range ...................................................... 1080p/1920 x 1200
HDMI Connector ...................................................... Type A 19 pin female
Digital Audio Output ....................................................................... Optical
Remote Control Port ....................................... RS232 female, mini-stereo
Power Consumption .......................................................... 20 Watts (max)
Dimensions ................................................... 10.25”W x 1.125”H x 4.25”D
Shipping Weight ............................................................................... 4 lbs.
9
WARRANTY
Note: These products are designed to be installed and serviced by trained professional
installation companies.
Linear LLC warrants this product to be free from defects in material and workmanship. For the
term of the warranty, see the list of products below. The Warranty Expiration Date is reected by
a date code that is afxed to all of Linear’s products. This warranty extends only to wholesale
customers who buy direct from Linear or through Linear’s normal distribution channels. Linear
does not warrant this product to consumers. Consumers should inquire from their selling dealer
as to the nature of the dealer’s warranty. There are no obligations or liabilities on the part of
Linear LLC for consequential damages arising out of or in connection with use or performance
of this product or other indirect damages with respect to loss of property, revenue, or prot, or
cost of removal, installation or reinstallation. All implied warranties, including implied warranties
for merchantability and implied warranties for tness, are valid only until warranty expiration date
as labeled on the product. This Linear LLC Warranty is in lieu of all other warranties express or
implied. Some states and countries do not allow limitations or how long an implied warranty lasts
or the exclusion or limitation or incidental or consequential damages, so the above exclusions
may not apply. The Linear LLC warranty gives specic legal rights in addition to other rights,
which may exist and vary from state to state and country to country.
All products returned for warranty service require a Return Product Authorization Number (RPA#).
Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
Consumers: If you have trouble locating your installing company, please contact Linear LLC at
1-800-421-1587 and we will assist you with locating a service and Installation Company.
The following warranty period applies to this set of Linear branded products.
Linear High Denition Video products — Two (2) years. There is no warranty offered on the 1.
batteries supplied with the IR remote Control.
The warranty is limited to repair or replacement of products returned, freight prepaid, to
Linear LLC. There is NO PROVISION FOR LABOR COST OR OTHER REIMBURSEMENTS
OF ANY KIND.
Failures due to product abuse, negligence, improper installation, improper use, and 1.
electrical surge including damage from lightning, water damage or other damage due to
natural disasters are not covered by the warranty.
The warranty shall also be voided by any tampering with the date code, labels or other 2.
markings on the product.
Products that are damaged in transit to Linear LLC due to improper packaging or by the 3.
carrier (shipping company) will not be covered under the warranty. If the product was
damaged or lost by the carrier, it is the sender’s responsibility to create a claim against the
carrier.
The user is responsible for all labor costs associated with removing, reinstalling and 4.
returning the product to Linear LLC.
Linear LLC, at its option, will repair or replace the defective product.5.
Replacements will be made from B-Stock. If an exact replacement is not available Linear 6.
LLC, at its option will select the nearest equivalent product. The user is responsible for
freight charges to Linear LLC.
Linear LLC will return warranted repaired or replacements by UPS Ground or an equivalent 7.
service. A customer may pay the additional costs for second day or next-day service.
10
HDMI-SW-2X2M
(760) 438-7000
(800) 421-1587 FAX (800) 468-1340
www.linearcorp.com
Rev A
Loading...