Linear DF-31-EC User Manual

Download

Page 1

DF-31/EC

SET SWITCH TO DELAYED FOR ENTRY/EXIT DOOR

SET SWITCH TO INSTANT FOR WINDOWS OR NON-ENTRY DOORS

MAGNET ON WINDOW

SENSOR ON FRAME

MAGNET ON DOOR

1/2" MINIMUM

MOUNT SENSOR PLATE TO FRAME

ALIGN MAGNET PLATE NEXT TO SENSOR PLATE AND ATTACH TO WINDOW

SPACE BELOW PLATE IS REQUIRED TO SNAP SENSOR ONTO PLATE

SNAP SENSOR ONTO MOUNTING PLATE

INSTALL TWO DURACELL TYPE DL 2032 BATTERIES (+) SIDE UP

LIFT

WHEN CONSOLE INDICATES A SENSOR LOW BATTERY, OPEN SENSOR CASE AND GENTLY LIFT UP END OF BATTERY CLAMP, SLIDE BATTERIES OUT

REMOVE BATTERIES FROM THIS END

NOTE: USE OF EXCESSIVE FORCE ON BATTERY CLAMP WILL RESULT IN DAMAGE

IF NECESSARY PUSH IN SLOT TO REMOVE SENSOR FROM MOUNTING PLATE

DOOR/WINDOW SENSOR

For Use with DF-16/EC Security Console

Installation Instructions

1. SENSOR & MAGNET DETAIL 2. SET SENSOR SWITCH 3. EX AMPLE SENSOR LOCATIONS

SENSOR HAS BUILT-IN SWITCH ON SIDE WITH NOTCH. MAGNET CAN ACTIVATE SWITCH UP TO 1/2" AWAY. WHEN MOUNTING SENSOR, ALIGN MAGNET TO NOTCH.

REMOVE PLASTIC BATTERY TAB PRIOR TO INSTALLATION BY PULLING STRAIGHT OUT

NOTCH ON SIDE OF SENSOR

ALIGN MAGNET NEXT TO NOTCH ON SENSOR

SENSOR

(760) 438-7000 • FAX (760) 438- 7043

www.linearcorp.com

MAGNET

1/2" SPACE MAXIMUM

4. PROGRAM SENSOR INTO CONSOLE 5. EX AMPLE SENSOR MOUNTING ON DOOR 6. EX AMPLE SENSOR MOUNTING ON WINDOW 7. OPTIONAL MAGNET SPACER

START IN

OFF MODE

ENTER YOUR

SECRET CODE

PRESS SENSOR OR MOVE MAGNET TO SEND SIGNAL

PRESS LEARN

UNUSED SENSOR

LEARN BUTTON

ENTER AN

NUMBER

HOLD OFF BUTTON FOR 3 SECONDS WHEN FINISHED TO EXIT LEARN MODE

8. TEST SENSOR 9. LABEL SENSORS 10. CHANGING BATTERIES INTERNATIONAL WARRANTY

SENSOR LIGHT SHOULD GLOW FOR TWO SECONDS

CONSOLE IN CHIME MODE SHOULD DING-DONG

SEND SIGNAL

FROM SENSOR

OPEN DOOR OR WINDOW

MOUNT SENSOR PLATE TO FRAME

1/2" MAXIMUM SPACE BETWEEN SENSOR AND MAGNET PLATES

SNAP SENSOR ONTO MOUNTING PLATE

STATUS INDICATOR SHOULD LIGHT WHEN SENSOR IS OPEN

Y C

N E G

E M E

USE LABELS PROVIDED TO IDENTIFY SENSORS

ALIGN MAGNET PLATE NEXT TO SENSOR PLATE AND ATTACH TO DOOR

Y C N

G E

M E

HOOK SPACER TO MAGNET PLATE AND ROTATE TO LOCK IN PLACE

R&TTE VAEE 28357, EMC, SFT, ETS

Linear Corporation declares that the apparatus DF-31/EC complies with the essential requirements and other relevant provisions of Directive 1995/5/EC.

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear Corporation for consequential damages

arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or proﬁ t, or cost of removal, installation, or reinstallation. All implied

warranties, including implied warranties for merchantability and implied warranties for ﬁ tness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other

warranties express or implied.

For warranty service on Linear equipment return product, at sender’s expense to: Linear Hong Kong 19/F Hounor Industrial Centre,6 Sun Yip Street Chai Wan, Hong Kong Attention: Repairs Department

REPAIRS POLICY

Charges will be made for equipment that is not of warranty, shows customer abuse, or is damaged by the effects of lightning, water, ﬁ re, or other abnormal happenings. Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured equipment at Linear’s discretion. The customer is always responsible for shipping and handling charges to the repairs facility. Linear will pay return shipping and handling charges on “in warranty” products shipped back to the customer. The customer will be billed for the return shipping and handling charges on “out of warranty” products. There will be a 50% expedite fee for any express requests. The International Sales Manager must be notiﬁ ed prior to the retur n of product to Linear. All international returns must have an International Repair Authorization number (IRA#). The number must be marked on all packages. Failure to do so will cause delays in processing.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and ﬁ ll an important need in portable wireless signaling. However, there are some limitations which must be observed. The radios are required to comply with local rules and regulations as radio devices. As such, they have limited transmitter power and therefore limited range. A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. Changes or modiﬁ cations to the device may void regulatory compliance. Infrequently used radio links should be tested regularly to protect against undetected interference or fault. A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

USE SPACER WHEN SURFACES ARE UNEVEN