Linear DF-16-EC, DF-54-EC User Manual

Download

Page 1

DF-54/EC

MOTION

DETECTOR

DON'T POINT AT HEAT SOURCES (HEATERS, ETC.), WINDOWS, OTHER MOTION DETECTORS OR DOOR/WINDOW TRANSMITTERS

BEDROOM

BATH

KITCHEN

FRONT ROOM

CONSOLE

(FOR INDOOR

USE ONLY)

MOUNT

DETECTOR

SO THAT

INTRUDER

WILL CROSS

BEAMS

ENTER YOUR

SECRET CODE

PRESS LEARN

ENTER AN

UNUSED SENSOR

NUMBER

PUSH WALK

TEST BUTTON

TO SEND SIGNAL

FROM MOTION

DETECTOR

START IN

OFF MODE

HOLD OFF BUTTON FOR 3 SECONDS WHEN FINISHED TO EXIT LEARN MODE

LEARN BUTTON

WALK TEST BUTTON

MOTION DETECTOR

For Use with DF-16/EC Security Console

Installation Instructions

1. MOTION DETECTOR DETAIL 2. TYPICAL INSTALLATION 3. MOTION DETECTION PATTERN

MOTION

DETECTOR LENS

MOTION DETECTOR IN CORNER

9 METERS

DETECTION

AREA

WALK

9 METERS

TEST

TOP

VIEW

BUTTON

(760) 438-7000 • FAX (760) 438- 7043

www.linearcorp.com

CASE LOCKING SCREW (ON BOTTOM)

2-3 METERS

4. CONNECT BATTERY 5. MOUNT MOTION DETECTOR BASE 6. PROGRAM DETECTOR INTO CONSOLE 7. WALK TEST MOTION DETECTOR

MOUNTING THE DETECTOR

REMOVE SCREW AND OPEN CASE

CONNECT 9-VOLT ALKALINE BATTERY TO BATTERY CLIP (PLUS SIDE UP)

NOTE:

WAIT 5 MINUTES AFTER CONNECTING BATTERY

FOR DETECTOR

TO STABILIZE

USE CENTER

HOLES FOR

WALL

MOUNTING

PUNCH OUT REQUIRED HOLES FOR SCREW MOUNTING

NOTE:

THE DETECTOR CAN BE MOUNTED WITH DOUBLE STICK TAPE,

IN A CORNER IS PREFERRED

AFTER MOUNTING, SNAP DETECTOR ONTO BASE AND REPLACE CASE SCREW

USE SIDE HOLES

FOR CORNER

MOUNTING

MOUNT DETECTOR 6-8 FEET HIGH

8. ALARM TEST MOTION DETECTOR 9. REPLACING MOTION DETECTOR BATTERY 10. IMPORTANT DETECTOR INFORMATION

PLACE CONSOLE IN THE AWAY MODE

AFTER FIVE MINUTES, WALKING IN FRONT OF THE MOTION DETECTOR SHOULD TRIGGER THE ALARM

PLACE CONSOLE IN OFF MODE TO STOP SIREN, CHECK THAT SENSOR STATUS LIGHT IS BLINKING.

Y C

N E

G R

E M

Y C

G E

M E

STAY OUT OF THE MOTION DETECTION PATTERN AREA FOR AT LEAST FIVE MINUTES

WHEN CONSOLE INDICATES A LOW BATTERY FOR THIS SENSOR:

REMOVE SCREW AND OPEN CASE

REPLACE THE BATTERY WITH A FRESH 9-VOLT ALKALINE BATTERY (PLUS SIDE UP)

USE ALKALINE BATTERY ONLY

SNAP DETECTOR ONTO BASE AND REPLACE CASE SCREW WHEN FINISHED

NOTE: WAIT 5 MINUTES AFTER REPLACING BATTERY FOR DETECTOR TO STABILIZE

1. The motion detector can only trigger the alarm when the Console is in Away Mode.

2. Except in “Walk Test”, the detector must see no motion for ﬁ ve minutes before walking in front of the unit will send an alarm signal.

3. When the Console is in Away Mode, the motion detector will cause an instant alarm unless a delayed perimeter door/window sensor is triggered ﬁ rst.

4. Operating temperature range: +32° to +120° F (0° to +49° C)

R&TTE VAEE 27837, EMC, SFT, ETS

Linear Corporation declares that the apparatus DF-54/EC complies with the essential requirements and other relevant provisions of Directive 1995/5/EC.

PUSH WALK TEST BUTTON

UNIT WILL STAY IN WALK TEST MODE FOR 4 MINUTES AFTER PRESSING WALK TEST BUTTON THEN AUTOMATICALLY RETURN TO "OPERATE" MODE

VERIFY THAT DETECTION PATTERN COVERS DESIRED AREA & THAT CONSOLE STATUS INDICATOR LIGHTS WHEN MOTION IS DETECTED

AFTER INITIAL SETUP, WALK TEST UNIT YEARLY

NOTE:

INTERNATIONAL WARRANTY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale

customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear Corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or proﬁ t, or cost of removal, installation, or reinstallation. All implied warranties,

including implied warranties for merchantability and implied warranties for ﬁ tness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied. For warranty service on Linear equipment return product, at sender’s expense to:

Linear Hong Kong 19/F Hounor Industrial Centre, 6 Sun Yip Street Chai Wan, Hong Kong Attention: Repairs Department REPAIRS POLICY Charges will be made for equipment that is not in warranty, shows customer abuse, or is damaged by the effects of lightning, water, ﬁ re, or other abnormal happenings.Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured equipment at Linear’s discretion.The customer is always responsible for shipping and handling charges to the repairs facility. Linear will pay return shipping and handling charges on “in warranty” products shipped back to the customer. The customer will be billed for the return shipping and handling charges on “out of warranty” products.There will be a 50% expedite fee for any express requests.The International Sales Manager must be notiﬁ ed prior to the return of product to Linear. All international returns must have an International Repair Authorization number (IRA#). The number must be marked on all packages. Failure to do so will cause delays in processing. IMPORTANT !!! Linear radio controls provide a reliable communications link and ﬁ ll an important need in portable wireless signaling. However, there are some limitations which must be observed. The radios are required to comply with local rules and regulations as radio devices. As such, they have limited transmitter power and therefore limited range. A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. Changes or modiﬁ cations to the device may void regulatory compliance. Infrequently used radio links should be tested regularly to protect against undetected interference or fault. A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

9 METERS

WALK IN FRONT OF UNIT WHILE WATCHING RED LIGHT

SIDE VIEW