Linear D-22B User Manual

D-22B

CODING SWITCH IN

TWO-CHANNEL RECEIVER

SET KEYS 3-8 TO
ANY VALID CODE

D-22B CODING SWITCH

MATCH CODE
ON KEYS 3-8

SET KEY

2 OFF

KEY 1 IS
UNUSED

KEYS 1 & 2

ARE UNUSED

DIGITAL
TRANSMITTER

Code Setting
Instructions

[phone] • FAX [phone]

USA & Canada (800) 42 1- 15 87 & (800) 392-012 3

Toll Free FAX [phone]

STEP 1

door located on the back of the transmitter case. Identify the
coding swit ch and note that it has eight positio ns, with ON and
OFF clearly marked.

Locate coding switch.

REMOVE BATTERY
ACCESS DOOR

Remove the battery access

CODING
SWITCH

TRANSMITTER DESCRIPTION

The D-22B is a two-but ton, two-channel hand-hel d digital radio
transmitter. The transmitter can perform a variety of remote
switching tasks when used with any of Linear’s Standard Digital
“D” Series Receivers. Typically the D-22B is used in wireless or
hybrid wireless/hardwire security systems.
The transmitter is powered by a 9-volt battery. Pressing the right
button will send a “Channel 1” signal, pressing the left button will
send a “Channel 2” signal. Hold buttons for at least 2 seconds
to activate the transmitter. The red LED on the face of the
transmitter will glow as the unit transmits and the receiv er with the
matching digital code will activate.
The Standard Digital radio format provides up to 256 different
digital codes. The code is set using the 8-position coding switches
in the transmitter and receiver.

STEP 2A

combination of OFF /ON co des an d set them on swit ch ke ys 2- 8 in
the transmitter Match the same code on switch keys 2-8 in the
receiver. Set receiver switch key 1 to OFF for the receiver to
activate from the
switch key 1 to ON for the receiver to activate from the
transmitter button (Channel 2).

D-22B CODING SWITCH

KEY 1 IS
UNUSED

Coding for single-channel receivers.

right

transmitter button ( Channel 1). Set rec eiver

SET KEYS
2-8 TO ANY
CODE

CODING SWITCHES IN RECEIVER

RECEIVER FOR

CHANNEL 1

MATCH
2-8

SET

1 OFF

RECEIVER FOR

CHANNEL 2

TRIGGERS FROM
RIGHT BUTTON

SET

1 ON

Pick any valid

left

MATCH
2-8

TRIGGERS FROM
LEFT BUTTON

D-22B transmitter switch key 1 is unus ed and can be set in
any position. The transmitter pushbuttons control the signal that

would normal ly be contro lled by switc h key 1. Pressi ng the right
button sends a signal a s if switc h key 1 is OFF. Pressi ng the left
button sends a signal as if switch key 1 is ON.

✶ CAUTION: All Standard Digital transmitters and receivers should be

recoded prior to installation and operation.

In order to avoid the possibility of duplicating codes in adjacent
systems, factory set codes should not be used. In addition, among
the valid codes availabl e, fo ur othe rs sho uld not be use d. These
include: all keys set ON or OFF and keys set in an alternating
ON/OFF or OFF/ON pattern.
The D-22B will transmit as long as a button is pressed. Depending
on conditions ( interference, ob stacles and distance to the receiver)
the receiver ou tput may or may not st ay activate d for as long as
the transmi tt er i s se nd ing a s ign al.

✶ CAUTION: If using two receivers, be sure they are located at least 10 feet

apart.

STEP 2B

Coding for two-channel receivers.

Pick any
combination of OFF /ON co des an d set them on swit ch ke ys 3- 8 in
the receiver. Match the same code on switch keys 3-8 in the
transmitter. Set the

transmitter

switch 2 to OFF. Right button will

activate Channel 1, left button will activate Channel 2. 2-Channel

receiver switch keys 1 & 2 are unused and can be set in any
position.

STEP 3

Test the equipment.

Connect the receiver to its power
source. With relay output receivers, listen for the relay click when
the transmitter is activated. A multi-meter can be used to detect
activation of relay and solid state output receivers. Operate the
transmitter from various locations to determine the radio range.

DCV DCV

COMMON

MEASURE

RESISTANCE

NORMALLY

OPEN

RELAY

OUTPUT

RECEIVER

OUTPUT

MEASURE
VOLTAGE

VOLTAGE

OUTPUT

RECEIVER

POWER

OUTPUT

MEASURE
VOLTAGE

RECEIVER

POWER

SHORT

-TO-

COMMON

OUTPUT

The battery should last 12 to 18 month s with normal u se. When

BATTERY REPLACEMENT

the red LED lights dimly, or not at all when transmitting, the battery
needs to be replace d. R em o ve the battery access door to change
the battery. Any type of 9-volt battery can be used. Replace the
battery do or an d f oam bat t ery pa d whe n f in ish ed .

REPLACE BATTERY WITH
FRESH 9-VOLT BATTERY

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The
Warranty Expiration Date is labeled on the product.
buy direct from Linear or through Linear’s normal distribution channels.

to consumers.

any.

There are no obligations or liabilities on the part of Linear corporation for consequential damages
arising out of or in connection with use or performance of this product or other indirect damages with
respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation.

warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until
Warranty Expiration Date as labeled on the product.

warranties express or implied.

For warranty service on Linear equipment return product, at sender’s expense to:
Linear Corporation Repairs Department
2580 Pioneer Avenue, Suite C
Vista, CA 92083

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signalling. However, there are some limitations which must be observed.

For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15

✶

devices. As such, they have limited transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals

✶

that occur on or near their operating frequencies, regardless of code settings.
Changes or modifications to the device may void FCC compliance.

✶

Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

✶

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or

✶

dealer, and these facts should be communicated to the ultimate users.

Copyright © 1995 Linear Corporation 200856 C

LINEAR LIMITED WARRANTY

This warranty extends only to wholesale customers

Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if

This Linear Corporation Warranty is in lieu of all other

Linear does not warrant this product

who

All implied