Linear CCM-RE1 Quick Start Manual

CCM-RE1

Color CCTV Camera Kit

PRODUCT DESCRIPTION

Linear’s Model CCM-RE1 (P/N ACP00886C) CCTV Color Camera Kit can be installed inside the RE-1 Entry System. The camera provides a video signal for viewing the area in front of the entry system. The CCTV Color Camera Kit requires the Front Window Lens Model # NDLENS-RE1. The camera is continuously powered by the RE-1. The camera’s infrared light emitters illuminate the area directly on front of the entry system for nighttime or low light operation. The camera focus has been factory adjusted to a range of three to four feet. The RE-1 CAMERA jack is used to connect the camera to the main circuit board with the single-

1. REMOVE BACK COVER & CIRCUIT BOARD

DISCONNECT THESE 2 CONNECTORS

REMOVE CIRCUIT BOARD

ended modular cable supplied with the camera. This cable routes power to and video from the camera. The RE-1 VIDEO jack is the connection for a video cable with a Type “BNC” connector. Cable runs of up to 300 feet of 75-ohm RG-59 video cable are acceptable. Longer cable runs may require

Installation Instructions

(760) 438-7000

USA & Canada (800) 421-1587 & (800) 392-0123

Toll Free FAX (800) 468-1340

www.linearcorp.com

the use of a video ampliﬁ er.

NOTE 1: Installations on existing systems must have the power disabled prior to removing the circuit board.

NOTE 2: The Color Camera will ONLY work with RE-1’s front window lens model number NDLENS-RE1. THIS NEW LENS HAS FOAM ON THE BACKSIDE. For installing the color camera for new or retroﬁ t installations, make sure that ONLY the NDLENS-RE1 is used. Remove the foam ONLY when installing

the color camera.

REMOVE THESE 4 SCREWS

2. REMOVE FACTORY INSTALLED FOAM & EXISTING LENS 3. REPLACE E XISTING LENS FROM CASE 4. MOUNT CAMERA & CONNECT LIGHTING POWER

IF FACTORY FOAM IS INSTALLED, REMOVE THE FOAM AND GO TO STEP 4

REMOVE THE FRONT WINDOW LENS AND REPLACE WITH THE NDLENS-RE1 LENS

INSERT THE WIRING HARNESS PLUG INTO

IF FACTORY FOAM IS NOT INSTALLED, REMOVE THESE 2 SCREWS FROM BEHIND THE FRONT

WINDOW LENS AND GO TO STEP 3

SECURE THE NDLENS-RE1 LENS WITH THESE 2 SCREWS

THE 2-PIN LIGHTING CONNECTOR

5. REPLACE CIRCUIT BOARD & BACK COVER 6. CONNECT CAMERA CABLE AND VIDEO CABLE LINEAR LIMITED WARRANTY

REPLACE CIRCUIT BOARD

RECONNECT THESE

2 CONNECTORS

PLUG THE CAMERA CABLE FROM THE CAMERA’S JACK INTO THE RE-1’

S CAMERA JACK

CONNECT THE MONITOR VIDEO CABLE INTO THE RE-1’S VIDEO OUTPUT CONNECTOR

This Linear product is warranted against defects in material and workmanship for twenty four (24) months. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations

or liabilities on the part of Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or proﬁ t, or cost of removal, installation, or reinstallation. All

implied warranties, including implied warranties for merchantability and implied warranties for ﬁ tness, are valid only until the warranty expires. This Linear LLC

Warranty is in lieu of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

SECURE THE CAMERA WITH THESE 2 SCREWS

IMPORTANT! TO PREVENT INTERNAL INFRARED LIGHT FROM ENTERING THE CAMERA, BE SURE THE FOAM GASKET AROUND THE CAMERA’S LEN’S PRESSES FIRMLY AGAINST THE RE-1’s FRONT WINDOW LENS

SECURE WITH 4 SCREWS