2GIG Gun Motion Detector
™
2GIG-GNGRD1-345
Read these instructions and warnings for the 2GIG Gun Motion Detector, your rearm
and your alarm system before installing or operating the 2GIG Gun Motion Detector.
Failure to do so, and/or to follow the instructions and warnings, could result in serious
injury, property damage and/or death.
WARNING: YOU MUST FOLLOW
ALL OF THESE SAFETY RULES
TO ENSURE THE SAFE USE
OF YOUR FIREARM. THE FAILURE TO
FOLLOW THE INSTRUCTIONS AND
WARNINGS IN THIS MANUAL COULD
CAUSE SERIOUS PERSONAL INJURY
OR DEATH TO YOU OR OTHERS AND
DAMAGE PROPERTY.
INSTALLATION INSTRUCTIONS
The 2GIG Gun Motion Detector (2GIG‐GNGRD1‐345) is designed for use with certain
hand guns and ries. It communicates with the control panel using the 345 MHz
frequency. When properly installed, and the gun is moved, signals are transmitted to
the control panel. See Working With Your GoControl Panel, next page, for expected
behavior.
Figure 1: 2GIG Gun Motion Detector
Side View
A Battery Access Cover B Motion Alert Light (Red)
C Combination Lock D Lock Release
A B
Bottom View
C D
Top View
Testing the Gun Motion Detector
Make sure the rearm is NOT loaded. After placing the Gun Motion Detector on a
compatible rearm, perform a motion test by simply picking it up to verify that it can
establish good Radio Frequency (RF) communications with the control panel.
WARNING! DO NOT USE THIS DETECTOR ON A LOADED GUN.
• Never install the 2GIG Gun Motion Detector on a loaded rearm.
Doing so could cause an accidental discharge causing serious
injury, property damage or death.
• Store rearms and ammunition separately and securely. Keep
rearms and ammunition out of the reach of children.
• Never use a broken or damaged 2GIG Gun Motion Detector.
IMPORTANT! This product will not lock all rearms. It will block access
to many guns when properly attached. Some lever action ries, rearms without
trigger guards surrounding the triggers, guns with extra light or extra wide triggers or
guns with trigger shoes or extensions may not be able to be effectively locked with
this Gun Motion Detector. The 2GIG Gun Motion Detector may be cut or defeated by a
determined individual and may not prevent the use of a rearm.
DISCLAIMER AND LIMITATION ON DAMAGES/REMEDIES
Nortek shall not be responsible, in any manner whatsoever for any injuries, damages
or death due to the failure or malfunction of the 2GIG Gun Motion Detector, or if
applicable, the linked alarm and/or discharge of a rearm. This includes any and all
liability in any way related to criminal conduct or the failure of the alarm to detect
movement of the 2GIG Gun Motion Detector and the rearm. You, not Nortek or
this device, are solely responsible for the accidental or intentional discharge of your
rearm.
Under no circumstances will Nortek be responsible for incidental or consequential
damages. Depending on the state in which you reside, different remedies may be
available to you.
Box Contents
Verify that the package includes the following:
• 1 - Gun Motion Detector
• 1 - CR2032 Battery (Installed)
Gun Motion Detector Operation
Instruction for use:
1 To open lock, set dials to combination
numbers (combination is always preset to
0-0-0 by factory).
2 With dials set to combination, move release
lever to up position.
3 Pull apart the two sides of the lock.
4 To close the lock, move release lever back
down to locked position and scramble
combination dials. Depending on your gun,
insert the front lock unit with ratchet post
through the trigger guard, behind trigger if
possible. Then insert rear unit.
Reset your personal combination:
1 Open the lock by pulling apart the two sides of the lock and completely remove
the detector from the gun.
2 Push the lever into the down position.
2GIG Gun Motion Detector
3 With dials set to the current combination, use a pen point or similar narrow object,
press the Reset Button on the left side of the lock in toward the center of the
lock.
4 Continue to apply pressure to the reset button, and set the dials to your
personalized combination.
5 Release the Reset Button, new combination is now set.
Reset Button
Inserting and Replacing the Batteries
To insert or replace the battery:
1 Remove from your rearm if the Detector is attached.
2 Remove the battery cover.
3 Carefully lift up on the front of the battery and pull straight out.
IMPORTANT: Always dispose and/or recycle used batteries in accordance with the
hazardous waste recovery and recycling regulations for your location. Your city, state,
or country may also require you to comply with additional handling, recycling, and
disposal requirements.
+
Storing The 2GIG Gun Motion Detector
The 2GIG-GNGRD-345 will periodically transmit a status signal to the 2GIG Control
Panel. If this device is placed in a safe or locked box the radio transmission may
be impeded. Ask your security dealer about adding a repeater to ensure effective
communications between the devices.
SPECIFICATIONS
Wireless Signal Range
Code Outputs Supervisory; Low Battery; Movement
Transmitter Frequency 345.00 MHz (crystal controlled)
Unique ID Codes
Supervisory Interval 70 minutes +/- 10 minutes
GoControl Sensor Type Tilt Sensor
Sensor Dimensions 2.7 x 2.3 x 1.4 in (69.5 x 57.3 x 36.4 mm)
Weight (including battery & magnet) 7.4 oz (210 g)
Housing Material ABS Plastic
Color Black
Operating Temperature -4° ‐ 140° F (-20° ‐ 60° C)
Relative Humidity 0‐90% Non‐Condensing
Battery (included)
Certication
350 ft (106.7 m), open air, actual range
may vary based on the wireless control
panel being used.
Over one (1) million different code
combinations
One (1) CR 2032 or equivalent Lithium
battery
FCC, IC and California DOJ-approved
Firearm Safety Device.
Bottom View
+
Bottom View
3 Insert the replacement battery. The plus (+) sign of the battery should be facing
up and the minus (‐) side facing down.
4 Replace the battery cover.
WARNING: Failure to follow these warnings and instructions can lead to heat
generation, rupture, leakage, explosion, re, or other injury, or damage. Do not insert
the battery into the compartment in the wrong direction. Always replace the battery
with the same or equivalent type (see Specications, right). Never recharge or
disassemble the battery. Never place the battery in re or water. Always keep batteries
away from small children. If batteries are swallowed, promptly see a doctor.
Working With Your GoControl© Panel
This 2GIG Gun Motion Detector is designed to send an alert transmission to your GoControl panel when there is natural movement. This alert can initiate a number of actions
based on the programming of the GoControl panel.
2GIG-GNGRD1-345 Scenarios – When Attached Gun is Moved
Panel Status Scenario 1 Scenario 2 Scenario 3 Scenario 4
Armed Away Alarm Alarm after entry delay Alarm Local Chime Notication
Armed Stay None None Alarm Local Chime Notication
Disarmed Local Chime Notication Local Chime Notication Local Chime Notication Local Chime Notication
Professional Installer Notes – Setup Conguration
Sensor Type Interior Follower Interior w/ Delay Day Zone No Response
Sensor Equip Type Motion Motion Motion Motion
Check with your Alarm Monitoring Company on how to set up push notications to your smartphone.
2GIG Gun Motion Detector
REGULATORY INFORMATION
This equipment has been tested and found to comply with the limits for Class B Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. Ľexploitation est autorisée aux deux conditions
suivantes: (1) ľappareil ne doit pas produire de brouillage, et (2) ľutilisateur de
ľappareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible ďen compromettre le fonctionnement.
FCC COMPLIANCE STATEMENT
This device complies with FCC Rules and Regulations as Part 15 devices as well as
Industry Canada license exempt RSS Rules and Regulations. Operation is subject to
the following two (2) conditions: This device may not cause harmful interference. This
device must accept any interference received, including interference that may cause
undesired operation.
INDUSTRY CANADA (IC) COMPLIANCE
This device complies with Industry Canada license‐exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may
cause undesired operation of the device. Repairs to certied equipment should be
made by an authorized Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or equipment malfunctions,
may give the telecommunications company cause to request the user to disconnect
the equipment. Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and internal metallic water
pipe system, if present, are connected together. This precaution may be particularly
important in rural areas. Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection authority, or
electrician, as appropriate.
LIMITED WARRANTY
This Nortek Security & Control LLC product is warranted against defects in material
and workmanship for two (2) years. This limited warranty extends only to wholesale
customers who buy direct from Nortek Security & Control LLC or through Nortek
Security & Control normal distribution channels. Nortek Security & Control does not
warrant this product to consumers. Consumers should inquire from their selling
dealer as to the nature of the dealer’s warranty, if any. NSC reserves the right to
update, change or replace any part of the terms listed herein by posting updates and/
or changes nortekcontrol.com. Please also refer to the NSC website for full limited
Warranty terms.
There are no obligations or liabilities on the part of Nortek Security & Control for
consequential damages arising out of or in connection with use or performance of this
product or other indirect damages with respect to loss of property, revenue, or prot,
or cost of removal, installation, or reinstallation. All implied warranties for functionality,
are valid only until the warranty expires. This Nortek Security & Control Warranty is in
lieu of all other warranties expressed or implied.
Nortek Security & Control LLC
2GIG
For technical support in the USA and Canada:
855‐2GIG‐TECH (855‐244‐4832)
Email: 2gigtechsupport@nortekcontrol.com
Visit www.nortekcontrol.com for technical support hours of operation
For technical support outside of the USA and Canada:
Contact your regional distributor
Visit www.dealer.2gig.com for a list of distributors in your region
10021223B
Loading...