Linear 2GIG-CAM-HD100 User Manual
2GIG HD100 CAMERA
Indoor HD camera with night vision
INSTALL INSTRUCTIONS
This document describes the basic installation information for the 2GIG Technologies HD100 Camera (2GIG CAM HD100). To install the HD100 Camera, you will need a PC with internet access.
Box Contents
•Camera
•Camera base
•Wire retention clip
•Power adapter
•4 non slip adhesive feet
SPECIFICATIONS
Ethernet |
10/100Mbps |
WiFi |
802.11b/g/n |
PIR |
Max 5m coverage |
IR LED |
5m illumination |
Adapter |
12V 1A |
HD Video |
Up to 720p 15fps |
Protocols |
H.264, MJPEG |
INSTALLING THE HD100 CAMERA
WiFi to the On-Site Router (WPS)
1If the on site router supports WPS, press the WPS button until the router goes into WPS mode (this will differ slightly from router to router). This action causes the router to listen for a new WPS device.
2Press the WPS button (A) on the HD100 Camera. This action causes the camera to announce itself to the router as a WPS device. While the camera is in WPS mode, the camera displays a blinking yellow LED.
3Do not press any buttons on the HD100 Camera until the camera LED displays green, indicating that the camera has successfully connected to the network.
4From the Alarm.com website add and configure the camera.
http://dealer.2gig.com/qr/hd100
WiFi to the On-Site Router
1Connect the camera directly to the router using an Ethernet cable.
2From the Alarm.com website add and configure the camera to connect using WiFi.
3Disconnect the Ethernet cable from the camera. A WiFi connection will be established.
Ethernet to the Router
1 Connect the camera directly to the router using an Ethernet cable.
2From the Alarm.com website add and configure the camera.
RESET TO DEFAULTS
•Press and hold button (B) until the camera LED changes to yellow (approximately 10 seconds). When the camera LED changes to yellow, release button (B) to reset the camera to factory defaults.
LED States
State |
LED Pattern |
Normal Operation |
Solid Green |
Connectivity Problems |
Blinking Red |
WPS Transaction in Progress |
Blinking Yellow |
Booting |
Solid Yellow |
IMPORTANT SAFETY INSTRUCTIONS
1Do not install this device near water.
2Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
3Only use attachments and accessories specified by 2GIG Technologies.
4Protect the power cord from being walked on or pinched particularly at the point where it exits from the device. (See figure below)
REGULATORY INFORMATION
This device complies with Part 15 of the FCC's Rules. Operation is subject to the following two conditions:
1This device may not cause harmful interference, and
2This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
This product complies with FCC radiation exposure limits for an uncontrolled environment. Avoid operating this product at a distance less than 20 cm from the user.
Caution: Any changed or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
IC approval
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
RÉGLEMENTATION IC: Cet appareil est conforme avec Industrie Canada exempts de license standard RSS (s). L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d'interférences, et
(2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du l'appareil.
Cet équipement est conforme aux limites IC exposition au rayonnement pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec distance minimum de 20cm entre l'utilisateur et l'élément rayonnant de l'appareil.
Remarque: le fabricant n'est pas responsable des interférences radio ou télévision causé par des modifications non autorisées de cet équipement. Une telle modification pourrait annuler l'autorité de l'utilisateur d'exploiter cet équipement.
This Class B digital apparatus complies with Canadian ICES 003
Cet appareil numérique de classe B est conforme Ia á norme NMB 003 du Canada.
LIMITED WARRANTY
This 2GIG Technologies product is warranted against defects in material and workmanship for 1 year. This warranty extends only to wholesale customers who buy direct from 2GIG Technologies or through 2GIG Technologies’ normal distribution channels. 2GIG Technologies does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any.
There are no obligations or liabilities on the part of 2GIG Technologies for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties for functionality, are valid only until the warranty expires. This 2GIG Technologies Warranty is in lieu of all other warranties expressed or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact 2GIG Technologies at 1(866)670 1591 for an RPA# and other important details.
Warranty service return address:
2GIG Technologies, Inc.
2961 W Maple Loop Drive
Lehi, Utah 84043
Technical Support Contact Information
Toll Free: 1(855) 244-4832
Email: techsupport @2gig.com
Internet: dealer.2gig.com
PN: 77 100001 001 Rev. F
Loading...