Lindy 52043 User Manual

Download

Page 1

For Home and Office Use Tested to Comply with FCC Standards

3G/ADSL2+ 802.11g VPN Router

User Manual English

LINDY No. 52043

www.LINDY.com

Page 2

English Manual

Table of content

Table of Content

INTRODUCTION TO YOUR ROUTER ............................................................................................ 3

FEATURES .......................................................................................................................................... 3

IMPORTANT NOTE FOR USING THIS ROUTER .......................................................................... 6

PACKAGE CONTENTS ..................................................................................................................... 7

THE FRONT LEDS ............................................................................................................................. 8

THE REAR PORTS ............................................................................................................................. 9

CABLING .......................................................................................................................................... 10

CONNECTING YOUR ROUTER .................................................................................................... 12

FACTORY DEFAULT SETTINGS ................................................................................................... 21

Web Interface (Username and Password) ...................................................................................... 21

Device LAN IP settings .................................................................................................................. 21

ISP setting in WAN site .................................................................................................................. 21

DHCP server .................................................................................................................................. 21

LAN and WAN Port Addresses ....................................................................................................... 21

INFORMATION FROM YOUR ISP ................................................................................................. 22

CONFIGURING WITH YOUR WEB BROWSER .......................................................................... 23

STATUS ............................................................................................................................................. 25

ADSL Status ................................................................................................................................... 25

3G Status ........................................................................................................................................ 26

EWAN Status .................................................................................................................................. 27

iBurst Status ................................................................................................................................... 28

ARP Table ....................................................................................................................................... 29

DHCP Table ................................................................................................................................... 30

Routing Table ................................................................................................................................. 31

NAT Sessions .................................................................................................................................. 32

UPnP Portmap ............................................................................................................................... 32

PPTP Status ................................................................................................................................... 33

IPSec Status .................................................................................................................................... 33

L2TP Status .................................................................................................................................... 34

Email Status ................................................................................................................................... 34

Event Log ....................................................................................................................................... 35

Error Log ....................................................................................................................................... 35

Diagnostic ...................................................................................................................................... 36

QUICK START .................................................................................................................................. 37

CONFIGURATION ........................................................................................................................... 41

LAN - Local Area Network ............................................................................................................. 42

WAN - Wide Area Network ............................................................................................................. 64

System ............................................................................................................................................ 86

Firewall and Access Control .......................................................................................................... 94

VPN - Virtual Private Networks .................................................................................................... 112

QoS - Quality of Service .............................................................................................................. 144

Virtual Server (known as Port Forwarding) ................................................................................ 153

Wake on LAN ................................................................................................................................ 161

Time Schedule .............................................................................................................................. 162

Advanced ...................................................................................................................................... 164

LOGOUT ......................................................................................................................................... 172

PROBLEMS STARTING UP THE ROUTER ................................................................................. 173

PROBLEMS WITH THE WAN INTERFACE ................................................................................ 173

PROBLEMS WITH THE LAN INTERFACE ................................................................................. 173

Page 3

English Manual

Chapter1: Introduction

Chapter 1: Introduction

Introduction to your Router

Welcome to the 3G/ADSL2+ (802.11g) (VPN) Firewall Router. The router is an “all-in-one” ADSL router, combining an ADSL modem, ADSL router and Ethernet network switch functionalities, providing everything you need to get the machines on your network connected to the Internet over your ADSL broadband connection. With features such as an ADSL Quick-Start wizard and DHCP Server, you can be online in no time at all and with a minimum of fuss and configuration, catering for first-time users to the guru requiring advanced features and control over their Internet connection and network.

Features

Express Internet Access

The router complies with ADSL worldwide standards. It supports downstream rate up to 12/24

Mbps with ADSL2/2+, 8Mbps with ADSL. Users enjoy not only high-speed ADSL services but

also broadband multimedia applications such as interactive gaming, video streaming and realtime audio much easier and faster than ever. It is compliant with Multi-Mode standard (ANSI

T1.413, Issue 2; G.dmt (ITU G.992.1); G.lite (ITU G.992.2); G.hs (ITU G994.1); G.dmt.bis (ITU G.992.3); G.dmt.bis.plus (ITU G.992.5)).

Virtual Private Network (VPN)

It allows user to make a tunnel with a remote site directly to secure the data transmission among the connection. User can use embedded PPTP and L2TP client/server, IKE and IPSec which are supported by this router to make a VPN connection or users can run the PPTP client in PC and the router already provides IPSec and PPTP pass through function to establish a VPN connection if the user likes to run the PPTP client in his local computer.

EWAN

Besides using 3G/ADSL to get connected to the Internet, the router offers its Ethernet port 1 as a WAN port to be used to connect to Cable Modems and fiber optic lines. This alternative, yet faster method to connect to the internet will provide users more flexibility to get online.

Dual WAN

Dual WAN is a new way of getting connected to the internet which is to use each two of the 3G/ADSL/EWAN to deal with the unexpected case and balance traffic load. That is a way of improving greatly the robustness.

802.11g Wireless AP with WPA Support

With integrated 802.11g Wireless Access Point in the router, the device offers a quick and easy access among wired network, wireless network and broadband connection (ADSL) with single device simplicity, and as a result, mobility to the users. In addition to 54 Mbps 802.11g data rate, it also interoperates backward with existing 802.11b equipment. The Wireless Protected Access (WPA1 and WPA2) and Wireless Encryption Protocol (WEP) supported features enhance the security level of data protection and access control via Wireless LAN.

Fast Ethernet Switch

A 4-port 10/100Mbps fast Ethernet switch is built in with automatic switching between MDI and MDI-X for 10Base-T and 100Base-TX ports. An Ethernet straight or crossover cable can be used directly for auto detection.

Page 4

English Manual

Chapter1: Introduction

Multi-Protocol to Establish a Connection

It supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516), and IPoA (RFC1577) to establish a connection with the ISP. The product also supports VC-based and LLC-based multiplexing.

Quick Installation Wizard

It supports a WEB GUI page to install this device quickly. With this wizard, end users can enter the information easily which they get from their ISP, then surf the Internet immediately.

Universal Plug and Play (UPnP) and UPnP NAT Traversal

This protocol is used to enable simple and robust connectivity among stand-alone devices and PCs from many different vendors. It makes network simple and affordable for users. UPnP architecture leverages TCP/IP and the Web to enable seamless proximity networking in addition to control and data transfer among networked devices. With this feature enabled, users can now connect to Net meeting or MSN Messenger seamlessly.

Network Address Translation (NAT)

Allows multi-users to access outside resources such as the Internet simultaneously with one IP address/one Internet access account. Many application layer gateway (ALG) are supported such as web browser, ICQ, FTP, Telnet, E-mail, News, Net2phone, Ping, NetMeeting, IP phone and others.

SOHO Firewall Security with DoS and SPI

Along with the built-in NAT natural firewall feature, the router also provides advanced hacker pattern-filtering protection. It can automatically detect and block Denial of Service (DoS) attacks. The router is built with Stateful Packet Inspection (SPI) to determine if a data packet is allowed through the firewall to the private LAN.

Domain Name System (DNS) Relay

It provides an easy way to map the domain name (a friendly name for users such as www.yahoo.com) and IP address. When a local machine sets its DNS server with this router’s IP address, every DNS conversion request packet from the PC to this router will be forwarded to the real DNS in the outside network.

Dynamic Domain Name System (DDNS)

The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic IP address is the WAN IP address. For example, to use the service, you must first apply for an account from a DDNS service like http://www.dyndns.org/. More than 5 DDNS servers are supported.

Quality of Service (QoS)

QoS gives you full control over which types of outgoing data traffic should be given priority by the router, ensuring important data like gaming packets, customer information, or management information move through the router ay lightning speed, even under heavy load. The QoS features are configurable by source IP address, destination IP address, protocol, and port. You can throttle the speed at which different types of outgoing data pass through the router, to ensure P2P users don’t saturate upload bandwidth, or office browsing doesn’t bring client web serving to a halt. In addition, or alternatively, you can simply change the priority of different types of upload data and let the router sort out the actual speeds.

Virtual Server (“port forwarding”)

Users can specify some services to be visible from outside users. The router can detect incoming service requests and forward either a single port or a range of ports to the specific local computer to handle it. For example, a user can assign a PC in the LAN acting as a WEB server inside and expose it to the outside network. Outside users can browse inside web servers directly while it is protected by NAT. A DMZ host setting is also provided to a local computer exposed to the outside network, Internet.

Page 5

English Manual

Chapter1: Introduction

Rich Packet Filtering

Not only filters the packet based on IP address, but also based on Port numbers. It will filter packets from and to the Internet, and also provides a higher level of security control.

Dynamic Host Configuration Protocol (DHCP) Client and Server

In the WAN site, the DHCP client can get an IP address from the Internet Service Provider (ISP) automatically. In the LAN site, the DHCP server can allocate a range of client IP addresses and distribute them including IP address, subnet mask as well as DNS IP address to local computers. It provides an easy way to manage the local IP network.

Static and RIP1/2 Routing

It has routing capability and supports easy static routing table or RIP1/2 routing protocol.

Simple Network Management Protocol (SNMP)

It is an easy way to remotely manage the router via SNMP.

Web based GUI

It supports web based GUI for configuration and management. It is user-friendly and comes with on-line help. It also supports remote management capability for remote users to configure and manage this product.

Firmware Upgradeable

Device can be upgraded to the latest firmware through the WEB based GUI.

Rich Management Interfaces

It supports flexible management interfaces with local console port, LAN port, and WAN port. Users can use terminal applications through the console port to configure and manage the device, or Telnet, WEB GUI, and SNMP through LAN or WAN ports to configure and manage the device.

Page 6

English Manual

Chapter 2: Installing the router

Chapter 2: Installing the Router

Important note for using this router

Page 7

English Manual

Chapter 2: Installing the router

Package Contents

3G/ADSL2+ 802.11g VPN Firewall Router

CD containing the online manual

RJ-11 ADSL/telephone Cable

Ethernet Cable

Console tool kit

Power adapter

A detachable antenna

Quick Start Guide （in the CD）

Page 8

English Manual

Chapter 2: Installing the router

The Front LEDs

LED Meaning

1 Power

Lit when power turns ON. Lit in red means the system is failed. To restart the device or connect service provider for support.

LAN Port 1X - 4X

(RJ-45 connector)

Lit when one of LAN ports connected to an Ethernet device. The speed of transmission hits 100Mbps appears Green; The speed of transmission hits 10Mbps appears Orange. Blinking when data is Transmitted / Received.

3 USB

Lit when the device connected to a USB device. Flash when the device is sending/receiving data.

4 Wireless

Lit green when the wireless connection is established. Flashes when the device is sending/receiving data. Flash once per second while wi-fi protected setup is in progress.

5 Mail Lit green when there are emails in the Inbox.

6 DSL

Lit Green when the device is successfully connected to an ADSL DSLAM.(“line sync”).

7 Internet

Lit green when IP connected. Flashes green when IP connected and IP traffic is passing through the device. Lit red when device attempted to become IP connected and failed. Lit off when device in bridged mode or when connection WAN is absent.

Page 9

English Manual

Chapter 2: Installing the router

The Ethernet Port #

4 can be

used as a

console

port

. You need a special

console tool which already includes in the package to connect with LAN port 4 and PC’s RS-232 port (9-pin serial port).

The Rear Ports

Port

Antenna

Connect the detachable antenna to this port.

DSL

Connect the supplied RJ-11 (“telephone”) cable on this port when connecting to the ADSL/telephone network.

USB

Connect the USB cable on this port.

LAN

1X - 4X

(RJ-45 connector)

Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the LAN ports when connecting to a PC or an office/home network of 10Mbps or 100Mbps.

Caution: Port 4 can be either a LAN or Console port at a time but not both.

5 WPS

Push WPS button to trigger Wi-Fi Protected Setup function.

6 RESET

To be sure the device is being turned on. Press RESET button for:

1-3 seconds: quick reset the device. 6 seconds above, and power off, power on the device:

restore to factory default settings. (Cannot login to the router or forgot your Username/Password. Press the button for more than 6 seconds).

Caution: After pressing the RESET button for more than 6 seconds, to be sure you power cycle the device again.

Power

Connect the supplied power adapter to this jack.

Power Switch

Power ON/OFF switch

Page 10

English Manual

Chapter 2: Installing the router

Cabeling

One of the most common causes of problems is the bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables.

Ensure that all other devices connected to the same telephone line as your router (e.g. telephones, fax machines, analogue modems) have a line filter connected between them and the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and ensure that all line filters are correctly installed and the right way around. Missing line filters or line filters installed the wrong way around can cause problems with your ADSL connection, including causing frequent disconnections.

Page 11

English Manual

Chapter 3: Basic Installation

Any TCP/IP capable workstation can be used to communicate with or through

the router. To configure other types of workstations, please consult the manufacturer’s documentation.

Chapter 3: Basic Installation

The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Windows 7, Linux, Mac OS, Windows 98/NT/2000/XP/Me, etc. The product provides an easy and user-friendly interface for configuration.

Please check your PC’s network components. The TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please refer to your Windows-related or other operating system manuals.

There are ways to connect with the router, either through an external repeater hub to the router or directly connecting with PCs. However, to be sure PCs have an Ethernet interface installed properly prior to connecting to the router device. You ought to configure your PCs to obtain an IP address through a DHCP server or a fixed IP address that must be in the same subnet as the router. The default IP address of the router is 192.168.1.254 and the subnet mask is 255.255.255.0 (i.e. any attached PC must be in the same subnet, and have an IP address in the range of 192.168.1.1 to

192.168.1.253). The best and easiest way is to configure the PC to get an IP address automatically from the router using DHCP. If you encounter any problem accessing the router’s web interface it may also be advisable to uninstall any kind of software firewall on your PCs, as they can cause problems accessing the 192.168.1.254 IP address of the router. Users should make their own decisions on how to best protect their network.

Please follow the steps below for your PC’s network environment installation.

Page 12

English Manual

Chapter 3: Basic Installation

Connecting Your Router

1. Connect this router to a LAN (Local Area Network) and the ADSL/telephone (ADSL) network.

2. Power on the device.

3. Make sure the Power is lit steadily and that the LAN LED is lit.

4. Connect RJ-11 cable to LINE Port when connecting to the telephone wall jack.

5. Connect USB 2.0 cable.

Page 13

English Manual

Chapter 3: Basic Installation

Configuring PCs in Windows

1. Go to Start. Click on Control Panel.

Then click on Network and Internet.

2. When the

Network and Sharing

Center window pops up, select and click

on Change adapter settings on the left window panel.

3. Select the

Local Area Connection

and right click the icon to select Properties.

Page 14

English Manual

Chapter 3: Basic Installation

4. Select

Internet Protocol Version 4

(TCP/IPv4) then click Properties.

5. In the

TCP/IPv4 properties

window,

select the Obtain an IP address

automatically and Obtain DNS Server address automatically radio buttons.

Then click OK to exit the setting.

6. Click OK again in the Local Area Connection Properties window to apply the new configuration.

Page 15

English Manual

Chapter 3: Basic Installation

Configuring PCs in Windows

Vista

1. Go to Start. Click on Network.

2. Then click on Network and Sharing Center at the top bar

3. When the Network and Sharing Center window pops up, select and click on Manage network connections on the left window column.

4. Select the Local Area Connection, and right click the icon to select Properties.

Page 16

English Manual

Chapter 3: Basic Installation

5. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties.

6. In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting.

7. Click OK again in the Local Area Connection Properties window to apply the new configuration

Page 17

English Manual

Chapter 3: Basic Installation

Configuring PCs in Windows XP

1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click Network Connections.

2. Double-click Local Area Connection. (See Figure 3.1)

3. In the LAN Area Connection Status window, click Properties. (See Figure 3.2)

4. Select Internet Protocol (TCP/IP) and click Properties. (See Figure 3.3)

5. Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons. (See Figure 3.4)

6. Click OK to finish the configuration.

Figure 3.1: LAN Area Connection

Figure 3.2: LAN Connection Status

Figure 3.3: TCP / IP

Figure 3.4: IP Address & DNS

Configuration

Page 18

English Manual

Chapter 3: Basic Installation

Configuring PCs in Windows 2000

Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and Dial-up Connections.

Double-click Local Area (“LAN”) Connection. (See Figure

3.5)

In the LAN Area Connection Status window, click Properties. (See Figure 3.6)

Select Internet Protocol (TCP/IP) and click Properties. (See Figure 3.7)

Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons. (See Figure 3.8)

Click OK to finish the configuration.

Figure 3.5: LAN Area Connection

Figure 3.6: LAN Connection Status

Figure 3.7: TCP / IP

Figure 3.8: IP Address & DNS

Configuration

Page 19

English Manual

Chapter 3: Basic Installation

Configuring PC in Windows 95/98/ME

1. Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and choose the Configuration tab.

2. Select TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card (NIC) in your PC. (See Figure 3.9)

3. Click Properties.

4. Select the IP Address tab. In this page, click the Obtain an IP address automatically radio button. (See Figure 3.10)

5. Then select the DNS Configuration tab. (See Figure 3.11)

6. Select the Disable DNS radio button and click OK to finish

the configuration.

Figure 3.9: TCP / IP

Figure 3.10: IP Address

Figure 3.11: DNS Configuration

Page 20

English Manual

Chapter 3: Basic Installation

Con

figuring PC in Windows NT4.0

Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and choose the Protocols tab.

Select TCP/IP Protocol and click Properties. (See Figure

3.12)

Select the Obtain an IP address from a DHCP server radio button and click OK. (See Figure 3.13)

Figure 3.12: TCP / IP

Figure 3.13: IP Address

Page 21

English Manual

Chapter 3: Basic Installation

Factory Default Settings

Before configuring your, you need to know the following default settings.

Web Interface (Username and Password)

Username: admin

Password: admin

The default username and password are “admin” and “admin” respectively.

Device LAN IP settings

IP Address: 192.168.1.254

Subnet Mask: 255.255.255.0

ISP setting in WAN site

PPPoE

DHCP server

DHCP server is enabled.

Start IP Address: 192.168.1.100

IP pool counts: 100

LAN and WAN Port Addresses

The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown as below.

LAN Port

WAN Port

IP address

192.168.1.254

The PPPoE function is enabled to automatically get the WAN port configuration from the ISP.

Subnet Mask

255.255.255.0

DHCP server function

Enabled

IP addresses for distribution to PCs

100 IP addresses continuing from

192.168.1.100 through 192.168.1.199

Attention

If you ever forget th

username/

password to login

to the router

, you may

press the RESET button up to 6 seconds to restore the factory default settings.

Caution: After pressing the RESET button for more than 6 seconds, to be sure you

power cycle the device again.

Attention

Page 22

English Manual

Chapter 3: Basic Installation

Information from your ISP

Before configuring this device, you have to check with your ISP (Internet Service Provider) to find out what kind of service is provided such as DHCP (Obtain an IP Address Automatically, Static IP (Fixed IP Address) and PPPoE.

Gather the information as illustrated in the following table and keep it for reference.

PPPoE(RFC2516)

VPI/VCI, VC / LLC-based multiplexing, Username, Password, Service Name, and Domain Name System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually).

PPPoA(RFC2364)

VPI/VCI, VC / LLC-based multiplexing, Username, Password and Domain Name System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually).

MPoA(RFC1483/RF C2684)

VPI/VCI, VC / LLC-based multiplexing, IP address, Subnet mask, Gateway address, and Domain Name System (DNS) IP address (it is a fixed IP address).

IPoA(RFC1577)

VPI/VCI, VC / LLC-based multiplexing, IP address, Subnet mask, Gateway address, and Domain Name System (DNS) IP address (it is a fixed IP address).

Pure Bridge

VPI/VCI, VC / LLC-based multiplexing to use Bridged Mode.

Page 23

English Manual

Chapter 3: Basic Installation

Configuring with your Web Browser

Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a user name and password window prompt will appear. The default username and password are “admin” and “admin” respectively. (See Figure 3.14)

Figure 3.14: User name & Password Prompt Window

Congratulations! You are now successfully logon to the Router!

Page 24

English Manual

Chapter 4: Configuration

At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired setup page, including:

Status

- ADSL Status

- 3G Status

- EWAN Status

- iBurst Status

- ARP Table

- DHCP Table

- Routing Table

- NAT Sessions

- UPnP Portmap

- PPTP Status

- IPSec Status

- L2TP Status

- Email Status

- Event Log

- Error Log

- Diagnostic

Quick Start

Configuration

- LAN

- WAN

- System

- Firewall

- VPN

- QoS

- Virtual Server

- Wake on LAN

- Time Schedule

- Advanced

Language (provides user interface in English and French languages)

Page 25

English Manual

Chapter 4: Configuration

Status

ADSL Status

This section displays the ADSL overall status, which shows a number of helpful information such as DSP firmware version.

Page 26

English Manual

Chapter 4: Configuration

3G Status

This section displays the 3G Card’s overall status, which shows you a number of helpful information such as the current signal strength and statistics on current and total bytes transferred and received.

Status: The current status of the 3G card.

Signal Strength: The signal strength bar indicates current 3G signal strength.

Network Name: The network name that the device is connected to.

Card Name: The name of the 3G card.

Card Firmware: The current firmware for the 3G card.

Current TX Bytes / Packets: The statistics of transmission, count for this call.

Current RX Bytes / Packets: The statistics of receive, count for this call.

Total TX Bytes / Packets: The statistics of transmission, count from system ready

Total RX Bytes / Packets: The statistics of receive, count from system ready

Page 27

English Manual

Chapter 4: Configuration

EWAN Status

Total TX Bytes / Packets: The statistics of total data transmission in bytes / packets since system ready. Total RX Bytes / Packets: The statistics of total data received in bytes / packets since system ready.

Page 28

English Manual

Chapter 4: Configuration

iBurst Status

Displays additional information of the 3G status when iBurst function is enabled in the 3G configuration such as its signal strength, card name, connection status and port class Ethernet.

Card Name: The name of the card.

Signal Strength: The signal strength bar indicates the current signal strength.

Current TX Bytes / Packets: The statistics of data transmission in bytes / packets during a call.

Current RX Bytes / Packets: The statistics of data received in bytes / packets during a call.

Total TX Bytes / Packets: The statistics of total data transmission in bytes / packets since system

ready.

Total RX Bytes / Packets: The statistics of total data received in bytes / packets since system ready.

Page 29

English Manual

Chapter 4: Configuration

ARP Table

This section displays the router’s ARP (Address Resolution Protocol) Table, which shows the mapping of Internet (IP) addresses to Ethernet (MAC) addresses. This is useful as a quick way of determining the MAC address of the network interface of your PCs to use with the router’s Firewall – MAC Address Filter function. See the Firewall section of this manual for more information on this feature.

IP Address: A list of IP addresses of devices on your LAN (Local Area Network).

MAC Address: The MAC (Media Access Control) addresses for each device on your LAN.

Interface: The interface name (on the router) that this IP Address connects to.

Static: Static status of the ARP table entry:

 “no” for dynamically-generated ARP table entries.

 “yes” for static ARP table entries added by the user.

Page 30

English Manual

Chapter 4: Configuration

DHCP Table

Leased: The DHCP assigned IP addresses information.

Expired: The expired IP addresses information.

Permanent: The fixed host mapping information

Leased Table

IP Address: The IP address that assigned to client.

MAC Address: The MAC address of client.

Client Host Name: The Host Name (Computer Name) of client.

Expiry: The current lease time of client.

Page 31

English Manual

Chapter 4: Configuration

Routing Table

Valid: It indicates a successful routing status.

Destination: The IP address of the destination network.

Netmask: The destination Netmask address.

Gateway/Interface: The IP address of the gateway or existing interface that this route will use.

Cost: The number of hops counted as the cost of the route.

RIP Routing Table

Destination: The IP address of the destination network.

Netmask: The destination Netmask address.

Gateway: The IP address of the gateway that this route will use.

Cost: The number of hops counted as the cost of the route.

Page 32

English Manual

Chapter 4: Configuration

NAT Sessions

This section lists all current NAT sessions between interface of types external (WAN) and internal (LAN).

UPnP Portmap

The section lists all port-mapping established using UPnP (Universal Plug and Play. See Advanced section of this manual for more details on UPnP and the router’s UPnP configuration options.

Page 33

English Manual

Chapter 4: Configuration

PPTP Status

This shows details of your configured PPTP VPN Connections.

Name: The name you assigned to the particular PPTP connection in your VPN configuration.

Type: The type of connection (dial-in/dial-out).

Enable: Whether the connection is currently enabled.

Active: Whether the connection is currently active.

Tunnel Connected: Whether the VPN Tunnel is currently connected.

Call Connected: If the Call for this VPN entry is currently connected.

Encryption: The encryption type used for this VPN connection.

IPSec Status

This shows details of your configured IPSec VPN Connections.

Name: The name you assigned to the particular VPN entry.

Active: Whether the VPN Connection is currently Active.

Connection State: Whether the VPN is Connected or Disconnected.

Statistics: Statistics for this VPN Connection.

Local Subnet: The local IP Address or Subnet used.

Page 34

English Manual

Chapter 4: Configuration

Remote Subnet: The Subnet of the remote site.

Remote Gateway: The Remote Gateway IP address.

SA: The Security Association for this VPN entry.

L2TP Status

This shows details of your configured L2TP VPN Connections.

Name: The name you assigned to the particular L2TP connection in your VPN configuration.

Type: The type of connection (dial-in/dial-out).

Enable: Whether the connection is currently enabled.

Active: Whether the connection is currently active.

Tunnel Connected: Whether the VPN Tunnel is currently connected.

Call Connected: If the Call for this VPN entry is currently connected.

Encryption: The encryption type used for this VPN connection.

Email Status

Details and status for the Email Account you have configured the router to check. Please see the Advanced section of this manual for details on this function.

Page 35

English Manual

Chapter 4: Configuration

Event Log

This page displays the router’s Event Log entries. Major events are logged to this window, such as when the router’s ADSL connection is disconnected, as well as Firewall events when you have enabled Intrusion or Blocking Logging in the Configuration – Firewall section of the interface. Please see the Firewall section of this manual for more details on how to enable Firewall logging.

Error Log

Any errors encountered by the router (e.g. invalid names given to entries) are logged to this window.

Page 36

English Manual

Chapter 4: Configuration

Diagnostic

It tests the connection to computer(s) which is connected to LAN ports and also the WAN Internet connection. If PING www.google.com is shown FAIL and the rest is PASS, you ought to check your PC’s DNS settings is set correctly.

Page 37

English Manual

Chapter 4: Configuration

Quick Start

1. Click Quick Start. Select the connect mode you want. There are three options you can choose,

ADSL, EWAN and 3G. Select ADSL from Connect Mode drop-down menu, and click Continue.

2. If your ADSL line is not ready, you need to check your ADSL line has been set or not.

3. If your ADSL line is ready, the screen appears ADSL Line is Ready. Choose Auto radio button and

click Apply. It will automatically scan the recommended mode for you. Manually mode makes you to set the ADSL line by manual. (If you choose Manually, you will directly go to step 5.)

4. The list below has different mode applied for your choice. Choose 0/33/PPPoE (Recommended)

and click Apply.

Page 38

English Manual

Chapter 4: Configuration

5. Please enter “Username” and “Password” as supplied by your ISP (Internet Service Provider) and

click Apply to continue.

Profile Port: Select the connection mode. There are ADSL EWAN and 3G.

Protocol: Select the protocol mode. The default mode is PPPoE.

VPI/VCI: Enter the VPI and VCI information provided by your ISP.

Username: Enter the username provided by your ISP.

Password: Enter the password provided by your ISP.

Service Name: This item is for identification purposes. If it is required, your ISP provides you the

information.

Authentication Protocol: Default is Auto. Your ISP advises on using Chap or Pap.

Page 39

English Manual

Chapter 4: Configuration

IP Address: Your WAN IP address. Leave this at 0.0.0.0 to obtain automatically an IP address from your ISP.

6. Configure the Wireless LAN setting.

WLAN Service: Default setting is set to Enable. If you want to use wireless, both 802.11g and 802.11b device in your network, you can select Enable. ESSID: The ESSID is the unique name of a wireless access point (AP) to be distinguished

from another. For security propose, change to a unique ID name to the AP which is already built-in to the router’s wireless interface. It is case sensitive and must not excess 32 characters. Make sure your wireless clients have exactly the ESSID as the device, in order to get connected to your network. ESSID Broadcast: It is function in which transmits its ESSID to the air so that when wireless client searches for a network, router can then be discovered and recognized. Default setting is Enable.

 Enable: When Enable is selected, you can allow anybody with a wireless client to be

able to locate the Access Point (AP) of your router.

 Disable: Select Disable if you do not want broadcast your ESSID. When select

Disable, no one will be able to locate the Access Point (AP) of your router.

Channel ID: Select the ID channel that you would like to use.

Security Mode: You can disable or enable with WPA or WEP for protecting wireless

network. The default mode of wireless security is Disable.

7. Wait for the configuration.

Page 40

English Manual

Chapter 4: Configuration

8. When ADSL is synchronic, it will appear “check”.

Page 41

English Manual

Chapter 4: Configuration

Configuration

When you click this item, you get following sub-items to configure the ADSL router.

- LAN, WAN, System, Firewall, VPN, QoS, Virtual Server, Wake on LAN, Time Schedule and

Advanced

These functions are described below in the following sections.

Page 42

English Manual

Chapter 4: Configuration

LAN - Local Area Network

Here are the items within the LAN section: Bridge Interface, Ethernet, IP Alias, Ethernet Client

Filter, Wireless, Wireless Security, Wireless Client Filter, WPS, Port Setting and DHCP Server.

Bridge Interface

You can setup member ports for each VLAN group under Bridge Interface section. From the example, two VLAN groups need to be created.

Ethernet: P1 (Port 1)

Ethernet1: P2, P3 and P4 (Port 2, 3, 4). Uncheck P2, P3, P4 from Ethernet VLAN port first.

Note: You should setup each VLAN group with caution. Each Bridge Interface is arranged in this order.

Bridge Interface VLAN Port (Always starts with)

ethernet P1 / P2 / P3 / P4 ethernet1 P2 / P3 / P4 ethernet2 P3 / P4 ethernet3 P4

Management Interface: To specify which VLAN group has possibility to do device management, like doing web management.

Note: NAT/NAPT can be applied to management interface only.

Page 43

English Manual

Chapter 4: Configuration

Ethernet

Primary IP Address

IP Address: The default IP on this router.

Subnet Mask: The default subnet mask on this router.

RIP: RIP v1, RIP v2, and RIP v2 Multicast. Check to enable RIP function.

IP Alias

This function creates multiple virtual IP interfaces on this router. It helps to connect two or more local networks to the ISP or remote node. In this case, an internal router is not required.

IP Address: Specify an IP address on this virtual interface.

SubNetmask: Specify a subnet mask on this virtual interface.

Security Interface: Specify the firewall setting on this virtual interface.

Internal: The network is behind NAT. All traffic will do network address translation when sending out

to Internet if NAT is enabled.

External: There is no NAT on this IP interface and connected to the Internet directly. Mostly it will be used when providing multiple public IP addresses by ISP. In this case, you can use public IP address in local network which gateway IP address point to the IP address on this interface.

DMZ: Specify this network to DMZ area. There is no NAT on this interface.

Page 44

English Manual

Chapter 4: Configuration

Ethernet Client Filter

The Ethernet Client Filter supports up to 16 Ethernet network machines that helps you to manage your network control to accept traffic from specific authorized machines or can restrict unwanted machine(s) to access your LAN.

There are no pre-define Ethernet MAC address filter rules; you can add the filter rules to meet your requirements.

Ethernet Client Filter: Default setting is set Disable.

 Allowed: check to authorize specific device accessing your LAN by insert the MAC Address

in the space provided or click . Make sure your PC’s MAC is listed.

 Blocked: check to prevent unwanted device accessing your LAN by insert the MAC Address

in the space provided or click . Make sure your PC’s MAC is not listed.

The maximum client is 16. The MAC addresses are 6 bytes long; they are presented only in hexadecimal characters. The number 0 - 9 and letters a - f are acceptable.

Note: Follow the MAC Address Format xx:xx:xx:xx:xx:xx. Semicolon ( : ) must be included.

Candidates: automatically detects devices connected to the router through the Ethernet.

Active PC in LAN

Page 45

English Manual

Chapter 4: Configuration

Active PC in LAN displays a list of individual Ethernet device’s IP Address & MAC Address which connecting to the router.

You can easily by checking the box next to the IP address to be blocked or allowed. Then, Add to insert to the Ethernet Client Filter table. The maximum Ethernet client is 16.

Wireless

Parameters

WLAN Service: Default setting is set to Enable. If you do not have any wireless, both 802.11g and

802.11b, device in your network, select Disable.

Mode: The default setting is 802.11b+g (Mixed mode). If you do not know or have both 11g and 11b

devices in your network, then keep the default in mixed mode. From the drop-down manual, you can select 802.11g if you have only 11g card. If you have only 11b card, then select 802.11b.

ESSID: The ESSID is the unique name of a wireless access point (AP) to be distinguished from another. For security purpose, change the default wlan-ap to a unique ID name to the AP which is already built-in to the router’s wireless interface. It is case sensitive and must not excess 32

Page 46

English Manual

Chapter 4: Configuration

characters. Make sure your wireless clients have exactly the ESSID as the device, in order to get connected to your network.

Note: It is case sensitive and must not excess 32 characters.

ESSID Broadcast: It is function in which transmits its ESSID to the air so that when wireless client searches for a network, router can then be discovered and recognized. Default setting is Enabled.

 Disable: If you do not want broadcast your ESSID. Any client uses “any” wireless setting cannot discover the Access Point (AP) of your router.

 Enable: Any client that using the “any” setting can discover the Access Point (AP) in

Regulation Domain: There are seven Regulation Domains for you to choose from, including North

America (N.America), Europe, France, etc. The Channel ID will be different based on this setting.

Channel ID: Select the wireless connection ID channel that you would like to use.

Note: Wireless performance may degrade if select ID channel is already being occupied by other AP(s).

TX PowerLevel: It is a function that enhances the wireless transmitting signal strength. User may

adjust this power level from minimum 1 up to maximum 127.

Note: The Power Level maybe different in each access network user premises environment and choose the most suitable level for your network.

Connected: Representing in true or false. That it is the connection status between the system and the build-in wireless card.

AP MAC Address: It is a unique hardware address of the Access Point.

AP Firmware Version: The Access Point firmware version.

WMM: This feature works concurrently with QoS that enables the system to prioritize the flow of

data packets according to 4 categories: Voice, Video, Best Efforts and Background.

Enable: Click to activate WMM feature.

Disable: Click to deactivate WMM feature.

Wireless Distribution System (WDS)

It is a wireless access point mode that enables wireless link and communication with other access point. It is easy to be installed simply to define peer’s MAC address of the connected AP. WDS takes advantages of cost saving and flexibility which no extra wireless client device is required to bridge between two access points and extending an existing wired or wireless infrastructure network to create a larger network. It can connect up to 4 wireless APs for extending cover range at the same time.

In addition, WDS enhances its link connection security in WEP mode, WEP key encryption must be the same for both access points.

WDS Service: The default setting is Disabled. Check Enable radio button to activate this function.

1. Peer WDS MAC Address: It is the associated AP’s MAC Address. It is important that your peer’s

AP must include your MAC address in order to acknowledge and communicate with each other.

2. Peer WDS MAC Address: It is the second associated AP’s MAC Address.

3. Peer WDS MAC Address: It is the third associated AP’s MAC Address.

Page 47

English Manual

Chapter 4: Configuration

4. Peer WDS MAC Address: It is the fourth associated AP’s MAC Address.

Note: For MAC Address, Semicolon ( : ) must be included.

Page 48

English Manual

Chapter 4: Configuration

Wireless Security

You can disable or enable with WPA or WEP for protecting wireless network. The default mode of wireless security is disabled.

WPA-PSK / WPA2-PSK / WEP

Security Mode: You can disable or enable with WPA or WEP for protecting wireless network. The default mode of wireless security is Disable.

WPA Algorithms: There are two types of the WPA-PSK, WPA-PSK and WPA2-PSK. The WPA-PSK

adapts the TKIP (Temporal Key Integrity Protocol) encrypted algorithms, which incorporates Message Integrity Code (MIC) to provide protection against hackers. The WPA2-PSK adapts CCMP (Cipher Block Chaining Message Authentication Code Protocol) of the AES (Advanced Encryption Security) algorithms.

WPA Shared Key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters.

Group Key Renewal: The period of renewal time for changing the security key automatically between wireless client and Access Point (AP). Default value is 600 seconds.

Page 49

English Manual

Chapter 4: Configuration

WEP

WEP Authentication: To prevent unauthorized wireless stations from accessing data

transmitted over the network, the router offers secure data encryption, known as WEP. If you require high security for transmissions, there are two options to select from: Open System,

Share key.

WEP Encryption: To prevent unauthorized wireless stations from accessing data transmitted over

the network, the router offers highly secure data encryption, known as WEP. If you require high security for transmissions, there are two alternatives to select from: WEP 64 and WEP 128. WEP 128 will offer increased security over WEP 64.

Passphrase: This is used to generate WEP keys automatically based upon the input string and a pre-defined algorithm in WEP64 or WEP128.

Default Used WEP Key: Select the encryption key ID; please refer to Key (1~4) below.

Key (1-4): Enter the key to encrypt wireless data. To allow encrypted data transmission, the WEP

Encryption Key values on all wireless stations must be the same as the router. There are four keys for your selection. The input format is in HEX style, 10 and 26 HEX codes are required for WEP64 and WEP128 respectively.

Page 50

English Manual

Chapter 4: Configuration

Wireless Client / MAC Address Filter

The MAC Address supports up to 16 wireless network machines and helps you manage your network control to accept traffic from specific authorized machines or to restrict unwanted machine(s) to access your LAN.

There are no pre-define MAC Address filter rules; you can add the filter rules to meet your requirements.

Wireless Client Filter: Default setting is set to Disable.

 Allowed: To authorize specific device accessing your LAN by insert the MAC Address in the

space provided or click . Make sure your PC’s MAC is listed.

 Blocked: To prevent unwanted device accessing the LAN by insert the MAC Address in the

space provided or click . Make sure your PC’s MAC is not listed.

The maximum client is 16. The MAC addresses are 6 bytes long; they are presented only in hexadecimal characters. The number 0 - 9 and letters a - f are acceptable.

Note: Follow the MAC Address Format xx:xx:xx:xx:xx:xx. Semicolon ( : ) must be included.

Candidates: it automatically detects devices connected to the router through the Wireless.

→Associated Wireless Clients

Associate Wireless Client displays a list of individual wireless device’s MAC Address that currently connects to the router. You can easily by checking the box next to the MAC address to be blocked or allowed. Then, Add to insert to the Wireless Client (MAC Address) Filter table. The maximum Wireless client is 16.

Page 51

English Manual

Chapter 4: Configuration

WPS

WPS feature is follow Wi-Fi Alliance WPS standard and it easily set up security-enabled Wi-Fi

networks in the home and small office environment. It is reduced by half the user steps to configure a

network and supports two methods that are familiar to most consumers to configure a network and

enable security.

Set up of security-enabled Wi-Fi network

Step 1: Note down the AP’s PIN from Web (Ex: 78749887).

Step 2: Open wireless client’s WPS utility (Ex: Atheros Jumpstart WPS utility), select “Configure a

wireless network” and apply “next” button.

Step 3: Enter AP’s PIN into the utility and click on the “next” button.

Page 52

English Manual

Chapter 4: Configuration

Step 4: These are two ways to trigger AP as Enrolee role, you can choose one to do it.

 Push AP’s WPS button 1 second and release it.

 In the AP’s WPS configuration page, change Role to “Enrollee” and apply “Start”

button.

Step 5: Jumpstart WPS utility search WPS AP.

Page 53

English Manual

Chapter 4: Configuration

Step 6: SSID and security will be generated automatically (You can change it) and apply “next”

button.

Step 7: WPS set up complete. And you have set up security-enabled Wi-Fi networks.

Page 54

English Manual

Chapter 4: Configuration

Page 55

English Manual

Chapter 4: Configuration

Set up of security-enabled Wi-Fi network using WCN in Vista

Step 1: Note down the AP’s PIN from Web (Ex: 78749887).

Step 2: In Vista’s Control Panel, select Network and Internet and choose View network computers

and devices. Double click the “ADSL Firewall Router” icon and enter the AP’s PIN code then click

“Next”.

Step 3: Enter the AP SSID and apply “Next” button.

Page 56

English Manual

Chapter 4: Configuration

Step 4: Enter the Passphrase and apply “Next” button.

Step 5: WCN set up complete. And you have set up security-enabled Wi-Fi networks.

Page 57

English Manual

Chapter 4: Configuration

Page 58

English Manual

Chapter 4: Configuration

Adding a new WPS device (wireless client) to a network - Use PBC Method

Step 1: Push AP’s WPS button more than one second and you will see AP’s WLAN led will flashing

per second.

Step 2: Open wireless client’s WPS utility, select “Join a wireless network” and apply “next” button.

Note: After you push AP’s WPS button, below steps should be completed between 2 minutes.

Step 3: Select “Push the button on my access point” and apply “next” button.

Step 4: New WPS device have join into the wireless network.

Page 59

English Manual

Chapter 4: Configuration

Page 60

English Manual

Chapter 4: Configuration

Adding a new WPS device (wireless client) to a network - Use PIN Method

Step 1: Open wireless client’s WPS utility, select “Join a wireless network” and apply “next” button.

Step 2: Note down the wireless client’s PIN (Ex: 41538142) and apply “Start” button for active

wireless client WPS PIN method.

Step 3: Enter wireless client’s PIN into “Enrollee’s PIN” of Web and apply “Start” button.

Page 61

English Manual

Chapter 4: Configuration

Step 4: New WPS device have join into the wireless network.

Page 62

English Manual

Chapter 4: Configuration

Port Setting

This section allows you to configure the settings for the router’s Ethernet ports to solve some of the compatibility problems that may be encountered while connecting to the Internet, as well allowing users to tweak the performance of their network.

Port # Connection Type: There are Six options to choose from: Auto, disable, 10M half-duplex, 10M full-duplex, 100M half-duplex, 100M full-duplex and Disable. Sometimes, there are Ethernet compatibility problems with legacy Ethernet devices, and you can configure different types to solve compatibility issues. The default is Auto, which users should keep unless there are specific problems with PCs not being able to access your LAN.

IPv4 TOS priority Control (Advanced users): TOS, Type of Services, is the 2nd octet of an IP packet. Bits 6-7 of this octet are reserved and bit 0-5 are used to specify the priority of the packet.

This feature uses bits 0-5 to classify the packet’s priority. If the packet is high priority, it will flow first and will not be constrained by the Rate Limit. Therefore, when this feature is enabled, the router’s Ethernet switch will check the 2nd octet of each IP packet. If the value in the TOS field matches the checked values in the table (0 to 63), this packet will be treated as high priority.

Page 63

English Manual

Chapter 4: Configuration

DHCP Server

You can disable or enable the DHCP (Dynamic Host Configuration Protocol) server or enable the router’s DHCP relay functions. The DHCP protocol allows your router to dynamically assign IP addresses to PCs on your network if they are configured to obtain IP addresses automatically.

To disable the router’s DHCP Server, check Disabled and click Next, then click Apply. When the DHCP Server is disabled you will need to manually assign a fixed IP address to each PCs on your network, and set the default gateway for each PCs to the IP address of the router (by default this is

192.168.1.254).

To configure the router’s DHCP Server, check DHCP Server and click Next. You can then configure parameters of the DHCP Server including the IP pool (starting IP address and ending IP address to be allocated to PCs on your network), lease time for each assigned IP address (the period of time the IP address assigned will be valid), DNS IP address and the gateway IP address. These details are sent to the DHCP client (i.e. your PC) when it requests an IP address from the DHCP server. Click Apply to enable this function. If you check “Use Router as a DNS Server”, the ADSL Router will perform the domain name lookup, find the IP address from the outside network automatically and forward it back to the requesting PC in the LAN (your Local Area Network).

If you check DHCP Relay Agent and click Next, then you will have to enter the IP address of the DHCP server which will assign an IP address back to the DHCP client in the LAN. Use this function only if advised to do so by your network administrator or ISP.

Click Apply to enable this function.

Page 64

English Manual

Chapter 4: Configuration

WAN - Wide Area Network

WAN refers to your Wide Area Network connection, i.e. your router’s connection to your ISP and the Internet. Here are the items within the WAN section: WAN Interface, WAN Profile and ADSL Mode.

WAN Interface

The factory default has the Connection Mode as ADSL and the Protocol as PPPoE.

Main Port—Dual WAN

Main Port: Select Dual WAN.

Mode Failover: Set to trigger ADSL / 3G failover function ready.

Page 65

English Manual

Chapter 4: Configuration

WAN1: Select “ADSL” “EWAN” or “3G” mode for WAN1.

WAN2: Select the left WAN mode for WAN2 as backup port. eg. If 3G is set for main port, then there

can be no option for failover/failback.

Time Schedule: A self defined time period. You may specify a time schedule for your prioritization

policy. For setup and detail, refer to Time Schedule section.

Keep Backup Interface Connected: Select Enable this function, the backup WAN port will connect

always.

Connectivity Decision: Set how many times of probing failed to switch backup port.

Failover Probe Cycle: Set the time duration for the Failover Probe Cycle to determine when the

router will switch to the backup connection (backup port) once the main connection (main port) fails.

Note: The time set is for each probe cycle, but the decision to change to the backup port is

determined by Probe Cycle duration multiplied by connection Decision amount (e.g. From the

image above it will be 60 seconds multiplied by 5 consecutive fails).

Failback Probe Cycle: Set the time duration for the Failback Probe Cycle to determine when the

router will switch back to the main connection (main port) from the backup connection (backup port)

once the main connection is communicating again.

Note: The time set is for each probe cycle, but the decision to change to the backup port is

determined by Probe Cycle duration multiplied by Connection Decision amount (e.g. From the

image above it will be 60 seconds multiplied by 5 consecutive fails).

Detect Rule:

Rule 1. Ping Fail

 No Ping: It will not send any ping packet to determine the connection. It means to disable the

ping fail detection.

 Ping Gateway: It will send ping packet to gateway and wait response from gateway in every

“Probe Cycle”.

 Ping Host: It will send ping packet to specific host and wait response in every “Probe Cycle”.

The host must be an IP address.

Page 66

English Manual

Chapter 4: Configuration

WAN Profile

ADSL

PPPoE Connection

PPPoE (PPP over Ethernet) provides access control in a manner which is similar to dial-up services using PPP.

Profile Port: Select the profile port as ADSL.

Protocol: The ATM protocol will be used in the device.

Description: A given name for the connection.

VPI/VCI: Enter the information provided by your ISP.

ATM Class: The Quality of Service for ATM layer.

Username: Enter the username provided by your ISP. You can input up to 128 alphanumeric

characters (case sensitive). This is in the format of “username@ispname” instead of simply “username”.

Password: Enter the password provided by your ISP. You can input up to 128 alphanumeric characters (case sensitive). Service Name: This item is for identification purposes. If it is required, your ISP provides you the information. Maximum input is 15 alphanumeric characters.

NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet through a single IP account, sharing the single IP address. If users on your LAN have public IP addresses and can access the Internet directly, the NAT function can be disabled.

Page 67

English Manual

Chapter 4: Configuration

IP (0.0.0.0: Auto): Your WAN IP address. Leave this at 0.0.0.0 to obtain automatically an IP address from your ISP.

Auth. Protocol: Default is Auto. Your ISP should advise you on whether to use Chap or Pap.

Connection:

 Always on: If you want the router to establish a PPP session when starting up and to automatically re-establish the PPP session when disconnected by the ISP.

 Connect on Demand: If you want to establish a PPP session only when there is a packet requesting access to the Internet (i.e. when a program on your computer attempts to access the Internet).

Idle Timeout: Auto-disconnect the broadband firewall gateway when there is no activity on the line for a predetermined period of time.

 Detail: You can define the destination port and packet type (TCP/UDP) without checking by timer. It allows you to set which outgoing traffic will not trigger and reset the idle timer.

MTU: Maximum Transmission Unit. The size of the largest datagram (excluding media-specific headers) that IP will attempt to send through the interface.

RIP: RIP v1, RIP v2, and RIP v2 Multicast. Check to enable RIP function.

TCP MSS Clamp: This option helps to discover the optimal MTU size automatically. Default is

enabled.

MAC Spoofing: This option is required by some service providers. You must fill in the MAC address that specify by service provider when it is required. Default is disabled.

Obtain DNS: A Domain Name System (DNS) contains a mapping table for domain name and IP addresses. DNS helps to find the IP address for the specific domain name. Check the checkbox to obtain DNS automatically.

Primary DNS: Enter the primary DNS.

Secondary DNS: Enter the secondary DNS

Page 68

English Manual

Chapter 4: Configuration

PPPoA Connection

Profile Port: Select the profile port as ADSL.

Protocol: The ATM protocol will be used in the device.

Description: A given name for the connection.

VPI/VCI: Enter the information provided by your ISP.

ATM Class: The Quality of Service for ATM layer.

Username: Enter the username provided by your ISP. You can input up to 128 alphanumeric

characters (case sensitive). This is in the format of “username@ispname” instead of simply “username”.

IP (0.0.0.0:Auto): Your WAN IP address. Leave this at 0.0.0.0 to obtain automatically an IP address from your ISP.

Auth. Protocol: Default is Auto. Your ISP should advise you on whether to use Chap or Pap.

Connection:

Page 69

English Manual

Chapter 4: Configuration

 Always on: If you want the router to establish a PPP session when starting up and to automatically re-establish the PPP session when disconnected by the ISP.

Idle Timeout: Auto-disconnect the broadband firewall gateway when there is no activity on the line for a predetermined period of time.

 Detail: You can define the destination port and packet type (TCP/UDP) without checking by timer. It allows you to set which outgoing traffic will not trigger and reset the idle timer.

MTU: Maximum Transmission Unit. The size of the largest datagram (excluding media-specific headers) that IP will attempt to send through the interface.

RIP: RIP v1, RIP v2, and RIP v2 Multicast. Check to enable RIP function.

TCP MSS Clamp: This option helps to discover the optimal MTU size automatically. Default is

enabled.

Primary DNS: Enter the primary DNS.

Secondary DNS: Enter the secondary DNS.

Page 70

English Manual

Chapter 4: Configuration

MPoA Connection

Profile Port: Select the profile port

as ADSL.

Protocol:

The ATM protocol will be used in the device.

Description: A given name for the connection.

VPI/VCI: Enter the information provided by your ISP.

ATM Class: The Quality of Service for ATM layer.

NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet

through a single IP account, sharing a single IP address. If users on your LAN have public IP addresses and can access the Internet directly, the NAT function can be disabled.

Encap. mode: Choose whether you want the packets in WAN interface as bridged packet or routed packet.

MTU: Maximum Transmission Unit. The size of the largest datagram (excluding media-specific headers) that IP will attempt to send through the interface.

IP (0.0.0.0:Auto):

Your WAN IP address. Leave this at 0.0.0.0 to obtain automatically an IP

address from your ISP.

Netmask: The default is 255.255.255.0. User can change it to other such as

255.255.255.128. Type the subnet mask assigned to you by your ISP (if given).

Gateway: Enter the IP address of the default gateway (if given).

RIP: RIP v1, RIP v2, and RIP v2 Multicast. Check to enable RIP function.

TCP MSS Clamp: This option helps to discover the optimal MTU size automatically. Default is

enabled.

Page 71

English Manual

Chapter 4: Configuration

MAC Spoofing: This option is required by some service providers. You must fill in the MAC address that specify by service provider when it is required. Default is disabled.

Primary DNS: Enter the primary DNS.

Secondary DNS: Enter the secondary DNS.

Page 72

English Manual

Chapter 4: Configuration

IPoA Routed Connection

Profile Port: Select the profile port

as ADSL.

Protocol: The ATM protocol will be used in the device.

Description: A given name for the connection.

VPI/VCI: Enter the information provided by your ISP.

ATM Class: The Quality of Service for ATM layer.

NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet

through a single IP account, sharing a single IP address. If users on your LAN have public IP addresses and can access the Internet directly, the NAT function can be disabled.

MTU: Maximum Transmission Unit. The size of the largest datagram (excluding media-specific headers) that IP will attempt to send through the interface.

IP (0.0.0.0:Auto): Your WAN IP address. Leave this at 0.0.0.0 to obtain automatically an IP address from your ISP.

Netmask: The default is 255.255.255.0. User can change it to other such as 255.255.255.128. Type the subnet mask assigned to you by your ISP (if given).

Gateway: Enter the IP address of the default gateway (if given).

RIP: RIP v1, RIP v2, and RIP v2 Multicast. Check to enable RIP function.

TCP MSS Clamp: This option helps to discover the optimal MTU size automatically. Default is

enabled.

Page 73

English Manual

Chapter 4: Configuration

Primary DNS: Enter the primary DNS.

Secondary DNS: Enter the secondary DNS.

Page 74

English Manual

Chapter 4: Configuration

Pure Bridge

Profile Port: Select the profile port

as ADSL.

Protocol:

The ATM protocol will be used in the device.

Description: A given name for this connection.

VPI/VCI: Enter the information provided by your ISP.

ATM Class: The Quality of Service for ATM layer.

Encap. mode: Choose whether you want the packets in WAN interface as bridged packet or

routed packet.

Acceptable Frame Type: Specify which kind of traffic goes through this connection, all traffic or only VLAN tagged.

Filter Type: Specify the type of ethernet filtering performed by the named bridge interface.

All

Allows all types of ethernet packets through the port.

Allows only IP/ARP types of ethernet packets through the port.

Pppoe

Allows only PPPoE types of ethernet packets through the port.

Primary DNS: Enter the primary DNS.

Secondary DNS: Enter the secondary DNS.

Page 75

English Manual

Chapter 4: Configuration

Multiple Session with PPPoE pass-through

Profile Port: Select the profile port

as ADSL.

Protocol:

The Multiple Session protocol will be used in the device.

Description: A given name for this connection.

VPI/VCI: Enter the information provided by your ISP.

ATM Class: The Quality of Service for ATM layer.

Username: Enter the username provided by your ISP. You can input up to 128 alpha-numeric

characters (case sensitive).

Password: Enter the password provided by your ISP. You can input up to 128 alpha-numeric

characters (case sensitive).

NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet

through a single IP account, sharing the single IP address. If users on your LAN have public IP

addresses and can access the Internet directly, the NAT function can be disabled.

IP (0.0.0.0:Auto): Your WAN IP address. Leave this at 0.0.0.0 to obtain automatically an IP

Page 76

English Manual

Chapter 4: Configuration

address from your ISP.

Auth. Protocol: Default is Auto. Your ISP should advise you on whether to use Chap or Pap.

Connection:

Always on: If you want the router to establish a PPPoA session when starting up and to

automatically

re-establish the PPPoA session when disconnected by the ISP.

Connect on Demand: If you want to establish a PPPoA session only when there is a packet

requesting access to the Internet (i.e. when a program on your computer attempts to access

the Internet).

Idle Timeout: Auto-disconnect the router when there is no activity on the line for a predetermined period of time.

MTU: Maximum Transmission Unit. The size of the largest datagram (excluding media-specific

headers) that IP will attempt to send through the interface.

RIP: RIP v1, RIP v2, and RIP v2 Multicast. Check to enable RIP function.

TCP MSS Clamp: This option helps to discover the optimal MTU size automatically. Default is

enabled.

Primary DNS: Enter the primary DNS.

Secondary DNS: Enter the secondary DNS.

If you want to establish several connections at the same time, check Enable to enable the second, third or fourth connection.

Before this, you need to configure your second, third or fourth connection firstly. Click Multiple Session-Second Session, the following screen will appear:

Page 77

English Manual

Chapter 4: Configuration

Configure the detailed information for your second connection like the previous one.

Page 78

English Manual

Chapter 4: Configuration

EWAN

Obtain an IP Address Automatically

When connecting to the ISP, This router also functions as a DHCP client. It can automatically obtain an IP address, netmask, gateway address, and DNS server addresses if the ISP assigns this information via DHCP.

Profile Port: Select the profile port

EWAN

Protocol: Select Obtain an IP Address Automatically.

NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet

through a single IP account, sharing the single IP address. If users on your LAN have public IP addresses and can access the Internet directly, the NAT function can be disabled.

Obtain DNS: Select Automatic to use DNS.

Primary DNS/ Secondary DNS: Enter the IP addresses of the DNS servers. The DNS servers are

passed to the DHCP clients along with the IP address and the subnet mask

Page 79

English Manual

Chapter 4: Configuration

Fixed IP Address

Select this option to set static IP information. You will need to enter in the Connection type, IP address, netmask, and gateway address, provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.

Profile Port: Select the profile port

EWAN

Protocol: Select Fixed IP Address.

IP: Your WAN IP address. Leave this at 0.0.0.0 to automatically obtain an IP address from your ISP.

Netmask: The default is 0.0.0.0. User can change it to other such as 255.255.255.0.Type the netmask assigned to you by your ISP (if given).

Gateway: You must specify a gateway IP address (supplied by your ISP).

NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet

through a single IP account, sharing the single IP address. If users on your LAN have public IP addresses and can access the Internet directly, the NAT function can be disabled.

Obtain DNS: Select Automatic to use DNS.

Primary DNS/ Secondary DNS: Enter the IP addresses of the DNS servers. The DNS servers

arepassed to the DHCP clients along with the IP address and the subnet mask.

Page 80

English Manual

Chapter 4: Configuration

PPPoE

PPPoE (PPP over Ethernet) provides access control in a manner which is similar to dial-up services using PPP.

Profile Port: Select the profile port

EWAN.

Username: Enter the username provided by your ISP. You can input up to 128 alphanumeric characters (case sensitive). This is in the format of “username@ispname” instead of simply “username”.

Password: Enter the password provided by your ISP. You can input up to 128 alphanumeric

characters (case sensitive).

Service Name: Enter a name for this connection.

IP: Your WAN IP address. Leave this at 0.0.0.0 to automatically obtain an IP address from your ISP.

Connection:

Always on: If you want the router to establish a PPPoE session when starting up and to

automatically re-establish the PPPoE session when disconnected by the ISP.

Connect on Demand: If you want to establish a PPPoE session only when there is a packet

requesting access to the Internet (i.e. when a program on your computer attempts to access the

Internet).

Idle Timeout: Auto-disconnect the router when there is no activity on the line for a predetermined period of time.

MTU: Maximum Transmission Unit. The size of the largest datagram (excluding mediaspecificheaders) that IP will attempt to send through the interface.

Page 81

English Manual

Chapter 4: Configuration

Auth. Protocol: Default is Auto. Your ISP advises on using Chap or Pap.

MAC Spoofing: Select Enable and enter a MAC address that will temporarily change your router’s

MAC address to the one you have specified in this field. Leave it as Disabled if you do not wish to change the MAC address of your router.

Obtain DNS: Select Automatic to use DNS.

Primary DNS/ Secondary DNS: Enter the IP addresses of the DNS servers. The DNS servers

arepassed to the DHCP clients along with the IP address and the subnet mask

Page 82

English Manual

Chapter 4: Configuration

Pure Bridge

Profile Port: Select the profile port

EWAN

Protocol: Select Pure Bridge.

Acceptable Frame Type: Specify which kind of traffic goes through this connection, all traffic oronly

VLAN tagged.

Filter Type: Specify the type of ethernet filtering performed by the named bridge interface.

All

Allows all types of ethernet packets through the port.

Allows only IP/ARP types of ethernet packets through the port.

Pppoe

Allows only PPPoE types of ethernet packets through the port.

Page 83

English Manual

Chapter 4: Configuration

The router allows you to insert a 3G/HSDPA card to its USB slot, enabling you to use a 3G/HSDPA, UMTS, EDGE, GPRS, or GSM Internet connection, makes downstream rates of to 14.4 Mbps*.

Profile Port: Select the profile port

as 3G.

iBurst: Enable or Disable the router’s iBurst functionality.

TEL No.: The dial string to make a GPRS / 3G user internetworking call. It may be provided by your

mobile service provider.

APN: An APN is similar to a URL on the WWW, it is what the unit makes a GPRS / UMTS call. The service provider is able to attach anything to an APN to create a data connection. Requirements for APN assignment varies between different service providers. Most service providers have an internet portal which they connect a DHCP Server to, giving you access to the internet i.e. Some 3G operators use the APN ‘internet’ for their portal. The default value of APN is “internet”.

Username: Enter the username provided by your service provider.

Password: Enter the password provided by your service provider.

Page 84

English Manual

Chapter 4: Configuration

Auth. Protocol: Manually specify CHAP (Challenge Handshake Authentication Protocol) or PAP (Password Authentication Protocol) if you know which authentication type the server is using (when acting as a client), or the authentication type you want the clients to use when tehy are connecting to you (when acting as a server). When using PAP, the password is sent unencrypted,while CHAP encrypts the password before sending, and also allows for challenges at different periods to ensure that an intruder has not replaced the client.

MTU: Maximum Transmission Unit. The size of the largest datagram (excluding media-specific

headers) that IP will attempt to send through the interface.

PIN: PIN stands for Personal Identification Number. A PIN code is a numeric value used in certain systems as a password to gain access, and authentication. In mobile phones a PIN code locks the SIM card until you enter the correct code. If you enter the PIN code incorrectly into the phone 3 times in a row, then the SIM card will be blocked and a PUK code will be required from your network / service provider to unlock it.

Connection:

Always On: The router will make UMTS/GPRS call when starting up. Enabling Always On,will

give you an option of Keep Alive.

Keep Alive: Set Enable to keep the router on line and prevent to be disconnected by the ISP

when they think there is no activity on the line.

Connect to Demand: If you want to make UMTS/GPRS call only when there is a packet

requesting access to the Internet (i.e. when a program on your computer attempts to access the Internet). In this mode, you must set Idle Timeout value at same time. Enabling Connect on Demand will give you an option of Idle Timeout.

Idle Timeout: Auto-disconnect the connection when there is no activity on this call for a

predetermined period of time. The default value is 10 min(s).

Obtain DNS Automatically: Select this checkbox to use DNS.

Primary DNS/ Secondary DNS: Enter the IP addresses of the DNS servers. The DNS servers

arepassed to the DHCP clients along with the IP address and the subnet mask.

Note: If you don’t know how to set these values and please keep them untouched.

Page 85

English Manual

Chapter 4: Configuration

ADSL Mode

Connect Mode: This mode will automatically detect your ADSL line code, ADSL2+, ADSL2, AnnexM2 and AnnexM2+, ADSL, All. Please keep the factory setting unless ADSL is detected as

the symptom of synchronization problem.

Modulation: It will automatically detect capability of your ADSL line mode. Please keep the factory setting unless ADSL is detected as the symptom of synchronization problem.

Profile Type: Please keep the factory settings unless ADSL is detected as the symptom of low link rate or unstable problems. You may need to change the profile setting to reach the best ADSL line rate, it depends on the different DSLAM and location.

Activate Line: Aborting (false) your ADSL line and making it active (true) again for taking effect with setting of Connect Mode.

Coding Gain: It reduces router’s transmit power which will effect to router’s downstream performance. Higher the gain will increase the downstream rate but it sometimes causes unstable ADSL line. The configurable ADSL coding gain is from 0 dB to 7dB, or automatic.

Tx Attenuation: It is the amount of power that modem (upstream) or DSLAM (downstream) is using. The lower the power the better the performance will be in modem upstream.

Elapsed Time: This is the ADSL connection uptime.

Page 86

English Manual

Chapter 4: Configuration

System

Here are the items within the System section: Time Zone, Remote Access, Firmware Upgrade,

Backup/Restore, Restart, User Management and Mail Alert.

Time Zone

The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server outside your network. Choose your local time zone, click Enable and click the Apply button. After a successful connection to the Internet, the router will retrieve the correct local time from the SNTP server you have specified. If you prefer to specify an SNTP server other than those in the list, simply enter its IP address as shown above. Your ISP may provide an SNTP server for you to use.

Daylight Saving is also known as Summer Time Period. Many places in the world adapt it during summer time to move one hour of daylight from morning to the evening in local standard time. Check

Automatic box to auto set your local time.

Resync Period (in minutes) is the periodic interval the router will wait before it re-synchronizes the

router’s time with that of the specified SNTP server. In order to avoid unnecessarily increasing the load on your specified SNTP server you should keep the poll interval as high as possible – at the absolute minimum every few hours or even days.

Page 87

English Manual

Chapter 4: Configuration

Remote Access

To temporarily permit remote administration of the router (i.e. from outside your LAN), select a time period the router will permit remote access for and click Enable. You may change other configuration options for the web administration interface using Device Management options in the Advanced section of the GUI.

If you wish to permanently enable remote access, choose a time period of 0 minute.

Page 88

English Manual

Chapter 4: Configuration

Firmware Upgrade

Your router’s “firmware” is the software that allows it to operate and provides all its functionality. Think of your router as a dedicated computer, and the firmware as the software it runs. Over time this software may be improved and revised, and your router allows you to upgrade the software it runs to take advantage of these changes.

Clicking on Browse will allow you to select the new firmware image file you have downloaded to your PC. Once the correct file is selected, click Upgrade to update the firmware in your router.

Page 89

English Manual

Chapter 4: Configuration

Backup / Restore

This function allows you to save a backup of the current configuration of your router to a file on your PC, or to restore a previously saved configuration. This is very useful if you wish to customize the setting of the router, knowing in advance that you can always restore the setting if any mistakes do occur. Therefore, It is advisable that you create a backup of the configuration of your router before customizing its configuration.

Create a Router Configuration Backup

To create a backup of the setting, simply press the Backup button and specify the location on where to save your configuration file. You may also change the name of the file if you wish to keep multiple backups.

Restoring the Router Configuration

To restore the configuration of the router, press Browse to locate the configuration file from your PC. Once the file has been located, click on the file then click on the Restore button to load the setting.

Note: You should only restore the setting with the files that have been created using the Backup function with the most current firmware version. Settings files saved to your PC should not be manually edited in any way.

Page 90

English Manual

Chapter 4: Configuration

Restart Router

Click Restart with option Current Settings to reboot your router (and restore your last saved configuration).

If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings.

You may also reset your router to factory settings by holding the small Reset pinhole button more than 6 seconds on the back of your router.

Caution: After pressing the RESET button for more than 6 seconds, to be sure you power cycle the device again.

Page 91

English Manual

Chapter 4: Configuration

User Management

In order to prevent unauthorized access to your router’s configuration interface, it requires all users to login with a password. You can set up multiple user accounts, each with their own password.

You are able to Edit existing users and Add new users who are able to access the device’s configuration interface.

Edit Account Information

You can change the informations of any account whether the account is active or valid.

1. To edit an account, select the Edit radio button of the account to be edited. Once selected, all

information of that account will be displayed.

2. Delete the information to be edited and replace it with the new one.

3. When it is done, simply click on the Edit/ Delete button to save your changes.

Note: It is recommended that you change the password immediately to prevent security

breach to your GUI.

To Add an Account

1. Check the Valid checkbox, fill in all the information: User name, Comment (optional), Password,

Confirm Password.

Page 92

English Manual

Chapter 4: Configuration

2. When it is done, click the Add button.

To delete a user account:

1. Click on the Delete radio button of the account you want to delete.

2. Then click the Edit/Delete to confirm the deletion.

Note: You can delete any user account except for the default admin account. Thus there isno delete radio button available for this account.

Page 93

English Manual

Chapter 4: Configuration

Mail Alert

Mail alert is designed to keep system administrator or other relevant personnels alerted of any unexpected events that might have occured to the network computers or server for monitoring efficiency. With this alert system, appropriate solutions may be tackled to fix problems that may have arisen so that the server can be properly maintained.

SMTP Server: Enter the SMTP server that you would like to use for sending emails.

Username: Enter the username of your email account to be used by the SMTP server.

Password: Enter the password of your email account.

Sender’s Email: Enter your email address.

Recipient’s Email (Failover / Failback): Enter the email address that will receive the alert message

once a computer / network server failover occurs.

Recipient’s Email (WAN IP Change Alert): Enter the email address that will receive the alert message once an WAN IP change has been detected.

Page 94

English Manual

Chapter 4: Configuration

When using Virtual Servers your PCs will be exposed to the degree

specified in your Virtual Server settings provided the ports specified are opened in your firewall packet filter settings.

Firewall and Access Control

Your router includes a full SPI (Stateful Packet Inspection) firewall for controlling Internet access from your LAN, as well as helping to prevent attacks from hackers. Besides, when using NAT, the router acts as a “natural” Internet firewall, as all PCs on your LAN will use private IP addresses that cannot be directly accessed from the Internet.

Firewall: Prevents access from outside your network. The router provides three levels of security support:

NAT natural firewall: This masks LAN users’ IP addresses which is invisible to outside users on the Internet, making it much more difficult for a hacker to target a machine on your network. This natural firewall is on when NAT function is enabled.

Firewall Security and Policy (General Settings): Inbound direction of Packet Filter rules to prevent unauthorized computers or applications accessing your local network from the Internet.

Intrusion Detection: Enable Intrusion Detection to detect, prevent and log malicious attacks.

Access Control: Prevents access from PCs on your local network:

Firewall Security and Policy (General Settings): Outbound direction of Packet Filter rules to

prevent unauthorized computers or applications accessing the Internet.

URL Filter: To block PCs on your local network from unwanted websites.

Page 95

English Manual

Chapter 4: Configuration

Here are the items within the Firewall section: General Settings, Packet Filter, Intrusion

Detection, URL Filter, IM/P2P Blocking and Firewall Log.

General Settings

You can choose not to enable Firewall and still able to access to URL Filter and IM/P2P Blocking or enable the Firewall using preset filter rules and modify the port filter rules as required. The Packet Filter is used to filter packets based-on Applications (Port) or IP addresses.

There are four options when you enable the Firewall, they are:

 All blocked/User-defined: no pre-defined port or address filter rules by default, meaning that all inbound (Internet to LAN) and outbound (LAN to Internet) packets will be blocked. Users have to add their own filter rules for further access to the Internet.

 High/Medium/Low security level: the predefined port filter rules for High, Medium and Low security are displayed in Port Filters of Packet Filter.

Select either High, Medium or Low security level to enable the Firewall. The only difference between these three security levels is the preset port filter rules in the Packet Filter. Firewall functionality is the same for all levels; it is only the list of preset port filters that changes between each setting. For more detailed on level of preset port filter information, refer to Table 1: Predefined Port Filter.

If you choose of the preset security levels and add custom filters, this level of filter rules will be saved even and do not need to re-configure the rules again if you disable or switch to other firewall level.

The “Block WAN Request” is a stand-alone function and not relate to whether security enable or disable. Mostly it is for preventing any scan tools from WAN site by hacker.

Page 96

English Manual

Chapter 4: Configuration

(Changed the format only.

Any remote user who is attempting to perform this action may result in

blocking all the accesses to configure and manage of the device from the Internet.

Page 97

English Manual

Chapter 4: Configuration

Packet Filter

This function is only available when the Firewall is enabled and one of these four security levels is chosen (All blocked, High, Medium and Low). The preset port filter rules in the Packet Filter must modify accordingly to the level of Firewall, which is selected. See Table1: Predefined Port Filter for more detail information.

Page 98

English Manual

Chapter 4: Configuration

Example: Predefined Port Filters Rules

The predefined port filter rules for High, Medium and Low security levels are listed. See Table 1.

Note: Firewall – All Blocked/User-defined, you must define and create the port filter rules yourself. No predefined rule is being preconfigured.

Table 1: Predefined Port Filter

Application Protocol

Port

Number

Firewall - Low Firewall - Medium Firewall – High

Start End Inbound Outbound Inbound Outbound Inbound Outbound

HTTP(80) TCP(6) 80 80 NO YES NO YES NO YES

DNS (53) UDP(17) 53 53 NO YES NO YES NO YES

DNS (53) TCP(6) 53 53 NO YES NO YES NO YES

FTP(21) TCP(6) 21 21 NO YES NO YES NO NO

Telnet(23) TCP(6) 23 23 NO YES NO YES NO NO

SMTP(25) TCP(6) 25 25 NO YES NO YES NO YES

POP3(110) TCP(6) 110 110 NO YES NO YES NO YES

NEWS(NNTP)

(Network News

Transfer Protocol)

TCP(6) 119 119 NO YES NO YES NO NO

RealAudio/ RealVideo (7070)

UDP(17) 7070 7070 YES YES YES YES NO NO

PING ICMP(1) N/A N/A NO YES NO YES NO YES

H.323(1720) TCP(6) 1720 1720 YES YES NO YES NO NO

T.120(1503) TCP(6) 1503 1503 YES YES NO YES NO NO

SSH(22) TCP(6) 22 22 NO YES NO YES NO NO

NTP /SNTP UDP(17) 123 123 NO YES NO YES NO YES

HTTP/HTTP Proxy (8080)

TCP(6) 8080 8080

NO YES NO NO NO NO

HTTPS(443) TCP(6) 443 443 NO YES NO YES N/A N/A

ICQ (5190) TCP(6) 5190 5190 YES YES N/A N/A N/A N/A

MSN (1863) TCP(6) 1863 1863 YES YES N/A N/A N/A N/A

MSN (7001) UDP(17) 7001 7001 YES YES N/A N/A N/A N/A

MSN VEDIO

(9000)

TCP(6) 9000 9000 NO YES N/A N/A N/A N/A

Inbound: Internet to LAN; Outbound: LAN to Internet.

Page 99

English Manual

Chapter 4: Configuration

YES: Allowed; NO: Blocked; N/A: Not Applicable

Packet Filter – Add TCP/UDP Filter

Rule Name: Users-define description to identify this entry or click “Select” drop-down menu to select existing predefined rules. The maximum name length is 32 characters.

Time Schedule: It is self-defined time period. You may specify a time schedule for your prioritization policy. For setup and detail, refer to Time Schedule section

Source IP Address(es) / Destination IP Address(es): This is the Address-Filter used to allow or

block traffic to/from particular IP address(es). Selecting the Subnet Mask of the IP address range you wish to allow/block the traffic to or form; set IP address and Subnet Mask to 0.0.0.0 to inactive the Address-Filter rule.

Tip: To block access, to/from a single IP address, enter that IP address as the Host IP Address and use a Host Subnet Mask of “255.255.255.255”.

Source Port: This Port or Port Ranges defines the port allowed to be used by the Remote/WAN to connect to the application. Default is set from range 0 ~ 65535. It is recommended that this option be configured by an advanced user.

Destination Port: This is the Port or Port Ranges that defines the application.

Type: It is the packet protocol type used by the application, select TCP, UDP or both TCP/UDP. Protocol Number: Insert the port number.

Inbound / Outbound: Select Allow or Block the access to the Internet (“Outbound”) or from the

Internet (“Inbound”).

Click Add button to apply your changes.

Page 100

English Manual

Chapter 4: Configuration

100

Packet Filter – Add Raw IP Filter

Go to “Type” drop-down menu, select “Use Protocol Number”.

Rule Name Helper: Users-define description to identify this entry or choosing “Select” drop-down menu to select existing predefined rules.

Time Schedule: It is self-defined time period. You may specify a time schedule for your prioritization policy. For setup and detail, refer to Time Schedule section

Protocol Number: Insert the port number, i.e. GRE 47.

Inbound / Outbound: Select Allow or Block the access to the Internet (“Outbound”) or from the

Internet (“Inbound”).

Click Add button to apply your changes.