LINDY 38274-80 User Manual [ml]

Tested to Comply with
FCC Standards
For Home and Office Use!

HDMI 2.0 4K Hybrid Cable

User Manual English
Benutzerhandbuch Deutsch
Manuel Utilisateur Français
Manuale Italiano

No. 38274-80

lindy.com

© LINDY Group – FOURTH EDITION (October 2017)

Technical Information

Minimum bend radius ~ 6cm
Max. pulling tensile load: 150N / 15kg

Max. HDMI data rate: 18Gbps, 6 Gbps per channel, 600MHz
Supports HDMI 1.4b/2.0, HDCP 1.4/2.2 pass through, Audio, CEC, no
support for HEC & ARC
Max. Resolutions: 2160p60 4:4:4 8/8 bit
Supports EDID and HDCP bi-directional communication

Environmental Specifications: For Indoor use only
Operating temperature: -10°C to 50°C
Storage temperature: -20°C to 60°C
Relative Humidity: 10 to 80% RH – non condensing

Powered via HDMI devices / connectors with additional USB power
input at RX side
Power requirement: 5VDC regulated +/- 0.25V, ~250 mA

Construction: Hybrid cable, fibre (high speed data) & copper (low speed
signals)
Cable construction: 4 fibre cores and 7 copper conductors
Cable jacket: PVC/TPU, diameter ~ 4.6mm
Connector dimensions: 60 x 19 x 9 mm approx.
Connector material: Aluminium

User Manual English

Introduction

Thank you for purchasing the Lindy HDMI 2.0 4K Hybrid Cable. This product has been designed to
provide trouble free, reliable operation. It benefits from both a LIND 2 year warranty and free lifetime
technical support. To ensure correct use, please read this manual carefully and retain it for future
reference.

Package Contents

 HDMI 2.0 4K Hybrid Cable
 This Manual

Features

 Suitable for use with computers, home theatres, video walls and professional equipment
 Supports HDMI 2.0 full Specification with transmission data rates up to 18Gbps
 Supports HDCP 1.4/2.2 pass through, Audio and CEC
 Supports HDMI resolutions up to Ultra HD 4K (3840x2160) 60Hz, 4:4:4, including 1080p 3D
 Supports EDID and HDCP bi-directional communication
 Supports lossless HDMI audio formats like Dolby True HD and DTS-HD, etc.
 Available in lengths from 10m to 100m (custom made lengths up to 150m available)

Installation

 This cable can be used in only one direction. The connectors are labelled “TX” and “RX”. Each

connector must be plugged in to the correct port to avoid display issues.

 The HDMI connectors include electronic chipsets that convert the electrical signal to an optical signal

and back. The chipsets require ~250mA of power, because some HDMI sources are unable to
provide enough power for TX and RX, the RX connector is equipped with a USB A type male
connector. Use an available USB port that can supply up to 500mA @5VDC or a USB power supply
with at least 250mA. Please see the LINDY website for USB power supplies and cables.

 Connect the cable to your devices before powering on your display and source to complete the

installation.

 The minimum bending radius of the hybrid cable is approximately 6cm , bending the cable to

a smaller radius could irreversibly destroy the cable.

 Never step on the cable or put any heavy pressure on to the cable
 The maximum pulling tensile load of the cable is 150N (15kg). Never pull the cable with higher

load.

Compatibility Remark:

During extensive tests we found a compatibility issue unique to the Xbox 1S. The HDMI signal produced
by the console is not sufficient to display a signal of 4K 60Hz 4:4:4. At the moment there is no solution
to this issue and it will require some changes from Microsoft.