Page 1
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (July 2011)
HDMI 1.4 4x2
Switching Splitter
Manual English
LINDY No. 38054
www.lindy.com
Page 2
Page 3
Manual English
1
Introduction
Thank you for purchasing the LINDY HDMI 1.4 4x2 Switching Splitter with remote
control. This high performance switch offers you the maximum convenience in HDMI
signal distribution when you have multiple HDMI sources and displays to connect
together. Each of the four HDMI sources can be directed to both HDMI displays, so
your displays can show the same source picture at the same time. When the HDMI
signal is progressed through the switch it is retimed and level compensated, so that
the output is a regenerated HDMI signal that can travel another 10 metres. The switch
also supports 3D video with protocols that will allow 3D displays and sources to
communicate through a HDMI link.
Each of the output ports support audio return channel (ARC) and HDMI Ethernet
channel (HEC) meeting the HDMI 1.4 specification.
The audio can also be outputted through the co-axial SPDIF port to an AV amp to
receive true audio from the sink. HEC adds a connection to the HDMI link which is
capable of carrying a 100Mbps full duplex Ethernet connection.
Package Contents
• HDMI 1.4 4x2 Switching Splitter
• 5V DC 2.6A multi country power supply
• Remote control (inc CR2025 battery)
• This manual
Features
• HDMI 1.4 compliant
o Audio return channel (ARC)
o 3D
o CEC
o HDMI Ethernet channel (HEC) high speed, bi-directional networking up to
100Mbps
• Supports HDTV resolutions: 480i, 480p, 576i, 576p, 720p, 1080i and 1080p
• Audio support
o HDMI 1.4 compatible audio interface
o Dolby TrueHD
o DTS-HD Master audio
o Full audio input & output support
• When used with computers, supports DVI-D resolutions up to UXGA (1600 x 1200)
• Supports both DVI-D source and display devices when using DVI-D/HDMI adapter
cables
• Each input/output can support up to 10 metres
• HDCP repeater support
• 24/30/36 bit deep colour support
• Dimensions: 240 x 104 x 44mm (WxDxH)
• Total weight: 1.27Kg
Page 4
Manual English
2
Connection & Operation
Make sure all devices are switched off before making any connections! Once all the
connections have been made, switch on the devices in this order: displays, HDMI
Switch, source devices.
1. IR Remote Control sensor: Using the included remote control, you can select any of
the connected inputs
2. LED Indicators: The HDMI switch will automatically detect the incoming audio/video
signal and illuminate the LED’s accordingly
3. Input Selection: A blue LED will illuminate when you press the input button to select
any of the connected sources
4. EDID Selection: Select either the STD (onboard EDID setting) or TV (display
attached to output port 1) for the EDID setting. To lock the EDID setting, press and
hold the EDID button for 3 seconds and the “lock” LED will illuminate red
5. Power button: Press to switch on the device and then press it again to put the
device in standby
1. RS232 Port: This port can be used to upgrade the firmware or allow control of the
switch via a serial cable
2. HDMI / Audio / Ethernet out:
a. HDMI: Connect your HDMI displays to the two HDMI out ports
b. Audio: Using SPDIF coaxial cable, connect these ports to your external amp
c. Ethernet: You can connect a PC or laptop to these ports to utilise the
Ethernet signal coming from your displays via the HEC
3. HDMI Input: Connect your HDMI source equipment to these input ports
4. Power: Attach the included 5V DC PSU to this port
Note: To utilise all the functions of this switch, you must use HDMI cables that support
ARC and HEC connections.
If using a device connected to the output port with ARC and have selected an input
with audio. The SPDIF port will give priority to the ARC signal. If you want to use the
audio from the input signal, you must disable ARC in the connected displays menu.
Page 5
Manual English
3
Notes on using DVI
-D
equipped devices:
To connect devices equipped with DVID connections, you can use either modular DVI/HDMI adapters or DVI/HDMI
adapter cables. Be aware that DVI-D is a ‘video only’ interface; audio signals are not
supported when using DVI-D source devices. Also, please note that DVI-D
equipped displays must support HDCP signal decoding to display HDCP protected
HDMI signals. HDCP compatible displays will normally feature the HD Ready logo.
Remote Control
1. Power Button: Press to switch on the device and then press
it again to put the device in standby
2. Input Selection: Press any of the buttons 1 – 4 to select the
desired source
RS-232 Protocol - Pin definition
Baud Rate: 9600bps
Data bit: 8 bits
Parity: None
Stop bit: 1 bit
Flow control: None
Command
4x2 HDMI Switch
Remote Control Console
PIN Definition
►
◄
PIN Definition
1 NC 1 NC
2 Tx 2 Rx
3 Rx 3 Tx
4 NC 4 NC
5 GND
5
GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Command
Action
POWER 00
Power Off (standby)
POWER 01
Power On
PORT 11
Output Select Input 1
PORT 12
Output Select Input 2
PORT 13
Output Select Input 3
PORT 14
Output Select Input 4
PORT 21
Output Select Input 1
PORT 22
Output Select Input 2
PORT 23
Output Select Input 3
PORT 24
Output Select Input 4
Page 6
Manual English
4
Page 7
CE/FCC & Recycling Information
CE Certification
This equipment complies with the requirements relating to
further Standards cited therein.
FCC Certification
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the F
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Y
ou are cautioned that changes or modification not expressly approved by the party responsible for compliance could void your
authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two c
onditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired operation.
WEEE (Waste of Electrical and Electronic Equipment),
Recycling of Electronic Products
United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electro
equipment. It is no longer allowable to simply throw away electrical and el
enter the recycling process.
Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways. Please
follow your national law when you want to dispose of any
your national WEEE recycling agency.
Germany
Die Europäische Union hat mit der WEEE Direktive umfassende Regelungen für die Verschrottung und das Recycling von
Elektro- und Elektronikp
rodukten geschaffen. Diese wurden von der Bundesregierung im Elektro
ElektroG in deutsches Recht umgesetzt. Dieses Gesetz verbietet vom 24.März 2006 an das Entsorgen von entsprechenden,
auch alten, Elektro- und Elektronikgerät
en über die Hausmülltonne! Diese Geräte müssen den lokalen Sammelsystemen bzw.
örtlichen Sammelstellen zugeführt werden! Dort werden sie kostenlos entgegen genommen. Die Kosten für den weiteren
Recyclingprozess übernimmt die Gesamtheit der Geräteherstelle
France
En 2006, l'union Européenne a introduit la nouvelle réglementation (DEEE) pour le recyclage de tout équipement électrique e
électronique.
Chaque Etat membre de l’ Union Européenne a mis en application la nouvelle réglementation DEEE de
différentes. Veuillez suivre le décret d’application correspondant à l’élimination des déchets électriques ou électroniques d
votre pays.
Italy
Nel 2006 l’unione europea ha introdotto regolamentazioni (WEEE) per la raccolta e il rici
Non è più consentito semplicemente gettare queste apparecchiature, devono essere riciclate. Ogni stato membro dell’ EU ha
tramutato le direttive WEEE in leggi statali in varie misure. Fare riferimento alle leggi
apparecchio elettrico o elettronico.
Per ulteriori dettagli fare riferimento alla direttiva WEEE sul riciclaggio del proprio Stato.
5
Electromagnetic Compatibility
Standards
ectronic equipment. Instead, these products must
electrical or electronic products. More details can be obtained from
-
r.
clo di apparecchi elettrici ed elettronici.
del proprio Stato quando si dispone di un
EN55022/EN55024 and the
CC
nic
-
und Elektronikgerätegesetz –
t
manières légèrement
e
LINDY No. 38054
1st Edition July 2011
www.lindy.com
Loading...