Page 1
10/100BaseTX to 100BaseFX
Media Converter Series
User’s Manual
2
FCC Warning
This device has been tested and found to comply
with limits for a Class B digital device, pursuant to
Part 2 and 15 of FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is
operated in a commercial environment. This
equipment generates and radiates radio frequency
energy and, if not installed and used in
accordance with the user’s manual, it may cause
interference in which case users will be required to
correct interference at their own expenses.
CE Warning
This is a Class B product. In a domestic
environment, this product may cause radio
interference in which case the user may be
required to take adequate measures.
3
Introduction
This Fast Ethernet Media Converter Series is
designed to bridge a 100BaseTX signal to a
100BaseFX signal. It’s used to extend the distance
connection between two Fast Ethernet twisted-pair
devices via the fiber cable transparently with no
performance degradation.
This Media Converter Series is based on the
switching hub design. It can support
Auto-Negotiation and Flow Control function on the
twisted-pair port. Besides, it can provide different
types of fiber connectors, such as SC, ST, MT-RJ
and LC for multi-mode or single-mode cables.
Package Contents
Before you start to install this Media Converter,
please verify your package that contains the
following items:
One Media Converter
One Power Adapter
One User’s Manual
4
Key Features
Compliant with IEEE 802.3 10BaseT and IEEE
802.3u 100BaseTX/100BaseFX Standards
One 10/100BaseTX Ethernet TP Port and One
100BaseFX Ethernet Fiber Port
One 100BaseFX Fiber Port can support either
Multi (SC/ST) or Single (SC, LC, MT-RJ) Mode
TP Port can support Half/Full-Duplex,
Auto-MDI/MDI-X and Auto-Negotiation
Providing a slide switch for Full- and
Half-Duplex selection on FX Port
Multiple Fiber Connectors
Providing 19” Converter Chassis for up to 16
slots with redundant power supply for optional
expansion use
Installation
DC Input & External Power Adapter
The External Power Adapter specification:
AC Input range from 90VAC to 260VAC
AC frequency range from 47Hz to 63Hz, TUV,
CE, UL Safety
Power Adapter DC Output is +5VDC 1.5A
The device DC Input is +5VDC 1A.
The TP Port
The device TP port support Auto-MDIX,
Auto-Negotiation and Flow Control functions. The
cable length is up to 100 meters for
Page 2
5
shielded/unshielded twisted-pair cable. It allows
users to connect the converter to 10BaseT and
100BaseTX devices.
The Fiber Port
There’re different types of fiber connectors, such
as SC, ST, MT-RJ and LC for multi-mode or
single-mode fiber cables. Users can have
Full-Duplex or Half-Duplex operation on the fiber
port by a slide switch at the right side of the
converter. The factory default is Full Duplex as the
below chart.
LEDs
LED Indicators of Fast Ethernet Media
Converter
LED Status
Operation
Power On Power is on.
Off Power is off.
FDX On Full Duplex
Off Half Duplex
Flashing Partial collision occurs
6
LINK/ACT On 10/100Mbps Port is for
connection
Flashing 10/100Mbps is data
activating
10/100M On Port is on 100M status.
Off Port is on 10M status.
Connections
Multi-Mode Fiber (MMF)
Single-Mode Fiber (SMF)
7
Technical Specifications
Standards
IEEE 802.3 10BaseT
IEEE 802.3u
100BaseTX/100BaseFX
Features
Number of Ports:
1 10/100BaseT with RJ-45
Connector
1 100BaseFX with Fiber
Connector (Multi/Single Mode,
ST/SC, LC, MT
-
RJ Connector)
Data Transfer Rate
Ethernet: 10Mbps/Half-Duplex
20Mbps/Full-Duplex
Fast Ethernet:
100Mbps/Half-Duplex
200Mbps/Full-Duplex
Transmission Media
10BaseT Cat. 3, 4, 5 UTP/STP,
up to 100 m
100BaseTX Cat. 5 UTP/STP, up
to 100 m
100BaseFX:
50/125µm or 62.5/125µm Multi
Mode ST/SC-Type Fiber optic
cable, up to 2 km
9/125µm or 10/125µm Single
Mode Fiber optic cable
LED Indicators
Per Port:
(TX): Link/Act, Speed, FDX/COL
(FX): Link/Act, FDX/COL
Per Unit: Power
Power Requirement
DC5V/2A
8
Power Consumption
10 Watts (Max)
Dimensions
102 x 74 x 22 mm (L x W x H)
Weight
230 g
Operating
Temperature
0 to 60
Storage
Temperature
-20 to 90
Humidity
10 to 90% RH (non-condensing)
Certifications
FCC Class B, CE
Page 3
9
Model Information
Model Description
Multi-Mode SC
Connector
100BaseFX Fiber, SC, MMF
Up to 415 meters (1360 ft.) for
MMF 50/125um or 62.5/125um
optic cables on Half-Duplex
operation.
Up to 2, 5km (1.24, 3.1 mi.) for
MMF 50/125um or 62.5/125um
optic cables on Full-Duplex
operation.
Multi-Mode ST
Connector
100BaseFX Fiber, ST, MMF
Up to 415 meters (1360 ft.) for
MMF 50/125um or 62.5/125um
optic cables on Half-Duplex
operation.
Up to 2, 5km (1.24, 3.1 mi.) for
MMF 50/125um or 62.5/125um
optic cables on Full-Duplex
operation
.
Multi-Mode MT-RJ
Connector
100BaseFX Fiber, MT-RJ, MMF
Up to 415 meters (1360 ft.) for
MMF 50/125um or 62.5/125um
optic cables on Half-Duplex
operation.
Up to 2km (1.24 mi.) for MMF
50/125um or 62.5/125um optic
cables on Full-Duplex operation.
10
Multi-Mode LC
Connector
100BaseFX Fiber, LC, MMF
Up to 415 meters (1360 ft.) for
MMF 50/125um or 62.5/125um
optic cables on Half-Duplex
operation.
Up to 5km (3.1 mi.) for MMF
50/125um or 62.5/125um optic
cables on Full-Duplex operation.
Single-Mode SC
Connector
100BaseFX Fiber, SC, SMF
Up to 10, 20, 40 or 60km for SMF
9125um optic cables on
Full-Duplex operation
Single-Mode LC
Connector
100BaseFX Fiber, LC, SMF
Up to 20, 40 or 60km for SMF
9125um optic cables on
Full-Duplex operation
Loading...