Page 1
Modules for
24 + 2Giga N-WAY SNMP Ethernet Switch
Short Guide English
LINDY No. 25032 2 Port RJ-45 Gigabit 10/100/1000Base-T
LINDY No. 25033 1 Port Fibre Optic Gigabit Type SC 1000Base-SX
LINDY No. 25034 2 Port Fibre Optic Gigabit Type SC 1000Base-SX
LINDY No. 25035 1 Port Fibre Optic Fast Ethernet Type SC 100Base-FX
LINDY No. 25036 2 Port Fibre Optic Fast Ethernet Type SC 100Base-FX
Please find the complete detai l ed user manual in PDF format on
the CD-ROM enclosed w ith the 24+2Giga SNMP N-Way Switch.
Unpacking
The product should contain the following items:
o One module according to the LINDY part number, check from Part No. above.
o This Short Guide
Installation
Before you install the module in the 24+2Giga SNMP Switch, turn off the power to the switch.
Unscrew the face plate of the module slot, this is on the front of the 24+2Giga SNMP Switch.
Then install the module by fixing the two module screws. Switch on the power to 24+2Giga
SNMP switch again.
After the Switch is powered on, it will perform “self-diagnostic” (POSD). This process takes
about 1 min and 40 seconds to complete, during this process, the “DIAG” LED will blink green
and the Switch will not respond to any configuration program. All the connections to the Switch
will not be available at this time. When the process is completed, the “DIAG” LED will stay solid
green.
The following table describes the meaning of each LED indicator.
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONI K GMBH - FIRST EDITION (JUNE 2003)
Page 2
Power
DIAG
Cooling
Fan 1
Fan 2
Link/Act
(1 ~24 port)
100 Mbps
(1 ~24 port)
Status LED Colour
Solid Blinking
Green Power is applied to this device N/A
Green Self Diagnostic successful Performing self diagnostic test
Red Left cooling fan failure N/A
Red Right cooling fan failure N/A
Green 10Mbit/sec link established TX/RX activity or collision
Green 100Mbit/sec link established N/A
OFF 10Mbit/sec established N/A
10/100/1000 Mbp/s RJ-45 Gigabit Port Optional Module
Bottom LED
Top LED
Middle LED
Top & Middle
LEDs
Green N/A TX/RX activity or collision
Orange 100Mbit/sec link established
when Middle LED OFF
Green 10Mbit/sec link established
when Top LED OFF
Orange
& Green
1000Mbit/sec link established
when both LED’s ON
N/A
N/A
N/A
FCC Compliance Statement (United States)
This equipment generates, uses and can radiate radio frequency energy and if not installed and
used properly, that is, in strict accordance with the manufacturer’s instructions, may cause
interference to radio communication.
It has been tested and found to comply with the limits for a class A computing device in
accordance with the specifications in Subpart B of part 15 of FCC rules, which are designed to
provide reasonable protection against such interference when the equipment is operated in a
commercial environment. Operation of this equipment in a residentia l area may cause
interference, in which case the user at his own expense will be required to take whatever
measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
Canadian Department of Communications RFI statement
This equipment does not exceed the class A limits for radio noise emissions from digital
apparatus set out in the radio interference regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la classe A prescrites dans le règlement sur le
brouillage radioélectriques publi é par le ministère des Communications du Canada
Tested to comply
with FCC Standards LINDY No. 25030 , 25032, 25033, 25034, 25035, 25036
Loading...