Safety Depends on You
RETURN TO MAIN MENU
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thoughtful operation on your part. DO
NOT INSTALL, OPERATE OR
REPAIR THIS EQUIPMENT
WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS CONTAINED
THROUGHOUT. And, most
importantly, think before you act
and be careful.
MAGNUM 250 LX
SPOOL GUN
K2490-1
IM887
July, 2006
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
OPERATOR’S MANUAL
Copyright © 2006 Lincoln Global Inc.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
i
SAFETY
WARNING
CALIFORNIA PROPOSITION 65 WARNINGS
Diesel engine exhaust and some of its constituents
are known to the State of California to cause cancer, birth defects, and other reproductive harm.
The Above For Diesel Engines
ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.
KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you
purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040,
Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the
Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
The Above For Gasoline Engines
i
FOR ENGINE
powered equipment.
1.a. Turn the engine off before troubleshooting and maintenance
work unless the maintenance work requires it to be running.
____________________________________________________
1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes
outdoors.
____________________________________________________
1.c. Do not add the fuel near an open flame welding arc or when the engine is running. Stop
the engine and allow it to cool before refueling to prevent spilled fuel from vaporizing on
contact with hot engine parts and igniting. Do
not spill fuel when filling tank. If fuel is spilled,
wipe it up and do not start engine until fumes
have been eliminated.
____________________________________________________
1.d. Keep all equipment safety guards, covers and devices in position and in good repair.Keep hands, hair, clothing and tools
away from V-belts, gears, fans and all other moving parts
when starting, operating or repairing equipment.
____________________________________________________
1.e. In some cases it may be necessary to remove safety
guards to perform required maintenance. Remove
guards only when necessary and replace them when the
maintenance requiring their removal is complete.
Always use the greatest care when working near moving
parts.
___________________________________________________
1.f. Do not put your hands near the engine fan.
Do not attempt to override the governor or
idler by pushing on the throttle control rods
while the engine is running.
1.h. To avoid scalding, do not remove the
radiator pressure cap when the engine is
hot.
ELECTRIC AND
MAGNETIC FIELDS
may be dangerous
2.a. Electric current flowing through any conductor causes
localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and
welding machines
2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.
2.c. Exposure to EMF fields in welding may have other health
effects which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1.
Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and
work cables. If the electrode cable is on your right
side, the work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.
___________________________________________________
1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenance
work, disconnect the spark plug wires, distributor cap or
magneto wire as appropriate.
2.d.5. Do not work next to welding power source.
Mar ‘95
ii
SAFETY
ii
ELECTRIC SHOCK can kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f.
Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
ARC RAYS can burn.
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases.When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
fumes and gases away from the breathing zone. When
welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and below Threshold Limit Values (TLV)
using local exhaust or mechanical ventilation. In
confined spaces or in some circumstances, outdoors, a
respirator may be required. Additional precautions are
also required when welding on galvanized steel.
5.b.
Do not weld in locations near chlorinated hydrocarbon
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors
form phosgene, a highly toxic gas, and other irritating products.
5.c. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
5.d. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
vapors
to
5.e. Also see item 1.b.
Mar ‘95
iii
SAFETY
iii
WELDING SPARKS can
cause fire or explosion.
6.a.
Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
the welding sparks from starting a fire.
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact can
cause overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even
been “cleaned”. For information, purchase “Recommended
Safe Practices for the
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
Sparks and spatter are thrown from the welding arc. Wear oil
6.f.
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate circuits.
This can create fire hazards or overheat lifting chains or
cables until they fail.
6.h. Also see item 1.c.
Remember that welding sparks and hot
though
they have
Preparation
for Welding and Cutting of
CYLINDER may explode
if damaged.
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
process used and properly operating
regulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected to
physical damage.
• A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
FOR ELECTRICALLY
powered equipment.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
Mar ‘95
iv
SAFETY
iv
PRÉCAUTIONS DE SÛRETÉ
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suivantes:
Sûreté Pour Soudage A L’Arc
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble de
soudage et la machine à souder en bon et sûr état defonctionnement.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le total
de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
8. S’assurer que la masse est connectée le plus prés possible de
la zone de travail qu’il est pratique de le faire. Si on place la
masse sur la charpente de la construction ou d’autres endroits
éloignés de la zone de travail, on augmente le risque de voir
passer le courant de soudage par les chaines de levage,
câbles de grue, ou autres circuits. Cela peut provoquer des
risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté, voir
le code “Code for safety in welding and cutting” CSA Standard
W 117.2-1974.
PRÉCAUTIONS DE SÛRETÉ POUR
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie du
corps.
3. Un coup d’arc peut être plus sévère qu’un coup de soliel, donc:
a. Utiliser un bon masque avec un verre filtrant approprié ainsi
qu’un verre blanc afin de se protéger les yeux du rayonnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
b. Porter des vêtements convenables afin de protéger la peau
de soudeur et des aides contre le rayonnement de l‘arc.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pantalons sans revers, et chaussures montantes.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
3. Avant de faires des travaux à l’interieur de poste, la debrancher à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur place.
Mar. ‘93
Thank
You
for selecting a QUALITY product by Lincoln Electric. We want you
Y
to take pride in operating this Lincoln Electric Company product •••
as much pride as we have in bringing this product to you!
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the time
the shipment is received.
Please record your equipment identification information below for future reference. This information can be found
on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
vv
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.
On-Line Product Registration
- Register your machine with Lincoln Electric either via fax or over the Internet.
• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.
• For On-Line Registration: Go to our
“Product Registration”. Please complete the form and submit your registration.
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then
WARNING
This statement appears where the information must be followed exactly to avoid serious personal injury or
loss of life.
CAUTION
This statement appears where the information must be followed to avoid minor personal injury or damage to
this equipment.
TABLE OF CONTENTS
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i-v
TABLE OF CONTENTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
PRODUCT DESCRIPTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
RECOMMENDED PROCESSES AND EQUIPMENT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3,4
UNPACKING THE SPOOL GUN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SPOOL GUN FAMILIARIZATION DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
OPERATING INSTRUCTIONS
SAFETY PRECAUTIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
‘SETUP PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SELECTING ELECTRODE WIRE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
LOADING ELECTRODE WIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5,6
DRIVE ROLL GROOVE SELECTION
MAKING A WELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
PROCEDURE SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
SETTING GAS F LOW RATE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
MAINTENANCE
TROUBLESHOOTING GUIDE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10,11
REPLACEMENT PARTS LIST DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-202-Z Series
1
MAGNUM 250 LX - General INFORMATION
PRODUCT DESCRIPTION
The 250 LX spool gun is a lightweight, handheld combined semiautomatic wire feeder and welding gun, designed primarily for aluminum welding using argon shielding gas. The feeding distance of
the self-contained wire supply to the arc is only several inches, eliminating the wire feeding problems normally associated with feeding
soft aluminum electrode through a conventional gun and cable
assembly. The cable included with the spool gun allows welding up
to 25 feet (7.6 m) from the power source.
The gun is intended for use with Power Mig 255C AND Power Mig
350MP Power Sources. For other applications, contact your local
Lincoln Electric sales office or distributor.
The spool gun is ideal for aluminum fabrication in industrial shops,
automobile body shops, marinas and for the advanced hobbyist.
SPECIFICATIONS
Model Magnum 250 LX Spool Gun with
Remote Wire Speed Control
Wire Capacity .023-.045” (0.6mm-1.2mm)
Solid and Hard Wire
.030-3/64” (0.8mm-1.2mm)
Aluminum and cored wire
Wire Speed 800 IPM MAX.
Duty Cycle 300 amps @ 60% CO2
280 amps @ 60% Argon Gas
200 amps @ 100% Argon Gas
Shipping Weight 25 Ft. (7.6m) - 17 Lbs. (7.7Kg.)
RECOMMENDED PROCESSES AND
EQUIPMENT
The spool gun can be used to weld aluminum and aluminum alloys
using Gas Metal Arc Welding or GMAW (also known as MIG)
process, which requires a supply of shielding gas. Argon is normally used due to its smooth, stable arc, good metal transfer, and low
cost. Positive polarity gives good penetration and affords a base
metal cathode cleaning effect.
Supplied with:
KP14H-35, .035 Contact Tip (Installed)
KP14AH-364, 3/64A Contact Tip (In Tip Holder of Spool Cover)
KP52FN, Gas Diffuser (Installed)
KP23-50, Gas Nozzle (Installed)
KP2518-2, Drive Roll (.030-.035-3/64)
Instruction Manual
2
MAGNUM 250 LX - INSTALLATION
Unpacking the Spool Gun
Safety Precautions
– Read "Safety Precautions" in the Operating Manual before
proceeding. Only personnel that have read and understood
the Operating Manual should install and operate this equipment.
– Power source must be turned "OFF" and power leads disconnected
when installing this unit.
BARREL ASSEMBLY
Unpacking the Spool Gun
Carefully unpack your Magnum 250 LX Spool Gun and attach the
Barrel Assembly, and make sure you have all of the parts shown
below.
OPERATOR’S
MANUAL
CABLE ASSEMBLY 25’
MAGNUM 250 LX - SPOOL GUN
KP14AH-364 Contact Tip 3/64th (1.2mm) Included
KP14H-35 Contact Tip .035 (0.9mm) Installed on Barrel Assembly
KP52FN Gas Diffuser Installed on Barrel Assembly
KP23-50 Gas Nozzle Installed on Barrel Assembly
KP2518-2 Drive Roll (.030 to .035 / 3/64th) Installed
3
MAGNUM 250 LX - INSTALLATION
A
B
C
D
E
G
F
"W" CLOCKED
CONNECTOR
(VIEWED FROM FRONT OF CONNECTOR)
A
B
G
D
F
E
TORCH
FUNCTIONS
+-
MOTOR
TORCH
C
POT
TORCH
13
2
5K
CW
TORCH
TRIGGER
RED
BLACK
WHITE
GREEN
BLUE
BROWN
YELLOW/ORANGE
Spool Gun Familiarization
Become familiar with your spool gun before connecting to welder.
For features described below, refer to Figure on the next page.
1. Handle, gun can be used in either right or left hand.
2. Trigger operates welding power, gas flow, and wire feed.
3. Remote wire speed control, located behind the handle, controls
the speed of the drive motor.
4. Open body cover by flipping lid and observe the following:
a. Wire drive release lever up position moves pressure roller
away from drive roll to stop wire feed. Down position moves
pressure roller to wire. Operate wire drive release lever and
see pressure roller move.
CONNECTING TO POWER SOURCE:
1. Power source must be “off” and power cord
disconnected.
b Drive roll with two wire grooves. Narrow groove feeds .030 or
.035 (0.9 mm) diameter wire. Wide groove feeds 3/64 inch (1.2
mm) diameter wire. Gun is shipped with wide groove or 3/64
in operating position (toward handle). Reverse roller for .030
or .035 inch (0.9 mm) diameter wire.
5. Gas nozzle directs gas flow around arc. Pull off gas nozzle to see
contact tip and gas diffuser. Spool gun is shipped with 3/64th inch
(1.2 mm) contact tip installed.
6. Electrode wire spool cover. Remove by unscrewing knob.
Electrode wire goes into gun through rear plastic tube.
7. Cable assembly for power, control, and gas.
Reassemble gun with spool of wire in spool holder. Hold gun and
become familiar with gun's weight and balance.
7-PIN SPOOL GUN
RECEPTACLE
2. Connect power cable to positive “+” stud.
Connect work cable & clamp to “-” stud.
3. Connect 7-Pin control cable plug to power
source receptacle.
4. Connect spool gun GAS hose to Gas solenoid
fitting.
5. Reconnect power and turn on machine.
ELECTRODE WIRE
POWER CABLE
CABLE
ASSEMBLY
GAS HOSE
SPOOL COVER
+ POSITIVE
CABLE AND STUD
GAS HOSE AND
5/8 FITTING
PRESSURE
ROLLER
NECK
GAS
DIFFUSER
CONTACT TIP
7 PIN CONTROL
PLUG FOR
TRIGGER, WIRE
SPEED MOTOR
WIRE SPEED
CONTROL
DRIVE
ROLL
DRIVE ROLL
RELEASE
LEVER
4
TRIGGER
GAS NOZZLE
HANDLE
MAGNUM 250 LX - OPERATING INSTRUCTIONS
Safety Precautions
WARNING
• Do not touch electrically live
parts or electrode with skin
or wet clothing
Consult your local dealer or appropriate AWS publication for help
in selecting an appropriate alloy type and wire size. Also refer to,
"Procedure Settings" later in this chapter, for wire sizes used with
typical base metal thicknesses and procedure settings.
ELECTRIC SHOCK
can kill.
FUMES AND GASES can be
dangerous.
WELDING SPARKS can
cause fire or explosion.
• Insulate yourself from work
and ground.
• Always wear dry insulating
gloves.
• Keep your head out of fumes.
• Use ventilation or exhaust to
remove fumes from breathing
zone.
• Keep flammable material
away.
• Do not weld on containers
that have held combustibles.
• Wear eye, ear and body
protection..
Loading Electrode Wire:
1. Unscrew gas nozzle and flip lid up on torch body then push idle
roller [pressure release lever up.
LID
(POSITION UP)
IDLER ROLLER
PRESSURE
RELEASE LEVER
(POSITION UP)
TORCH BODY
2. Unscrew and remove contact tip.
CONTACT TIP
ARC RAYS can burn.
WARNING: Electric shock can kill. Fumes and gases can be
dangerous to your health. Arc rays can injure eyes and burn
skin. See additional warning information under "Arc Welding
Safely Precautions" on inside of front cover of operating manual.
When inching, (the electrode and drive mechanism are always
electrically energized and remain energized several seconds
after the gun trigger is released.
Setup Procedure
Selecting Electrode Wire
Several alloy types of filler metals are available, and the best
choice depends on the type of base metals and the desired characteristics of the weldment, such as ductility and strength, corrosion resistance, sustained service temperature, and anodictreatment color matching. In addition, several wire sizes are available,
and the choice here will depend upon several factors, including
base metal thickness and the arc transfer process used.
3. Unscrew spool cover knob and remove spool cover.
SPOOL COVER
KNOB
SPOOL COVER
5
MAGNUM 250 LX - OPERATING INSTRUCTIONS
4. Select wire of size and type needed. Wire must be straight, with
no kinks or bends. Check drive roller for the correct groove
positioning for the size wire selected. See "Drive Roll Groove
Selection", for details.
5. Put wire spool on shaft. After spool wire is in place, make sure the
Spool Brake Lever is riding on outer flange of wire spool and, the
Roller Arm is underneath of spool riding on wire.
CORRECT
SPOOL BRAKE
LEVER
ROLLER ARM
INCORRECT
PRESSURE
LEVER
FRONT
TUBE
BACK TUBEDRIVE ROLL
PRESSURE
LID
IDLER
ROLL
8. Push wire until wire end extends approximately 6" (150 mm)
past end of gas diffuser. Re-engage idle roll pressure by pushing
release lever down as shown above, then close lid.
9. Screw spool cover knob onto spool gun cover (making sure all
keyways line up).
SPOOL COVER
KNOB
SPOOL COVER
ROLLER ARM
SPOOL BRAKE
LEVER
6. Unspool and straighten about 6 inches of wire, then route into
plastic tube.
WIRE SPOOL
PLASTIC
TUBE
10. Obtain contact tip size to match wire selected. Slip contact tip
over wire and screw into diffuser. Tighten securely.
CONTACT TIP
GAS NOZZLE
DIFFUSER
7. Push wire until end of wire exits back tube and enters front tube,
passing between drive roll & pressure idler roll.
11. Cut off wire close to contact tip, then screw gas nozzle over the
diffuser
6
MAGNUM 250 LX - OPERATING INSTRUCTIONS
CAUTION
DIFFUSER SET SCREW
Liner Installation:
Over tightening the Liner Retaining Set Screw can cause damage
to the Plastic Liner and cause wire feeding problems.
Drive Roll Groove Selection
The drive roll has two grooves. A wider groove for feeding 3/64”
(.047) wire and a narrow groove for feeding .030-.035” (0.8-
0.9mm) wire to accommodate changes in the wire size used.
Changing between the grooves simply requires reversing the
drive roll.
A. Drive Roll Orientation
NARROW
NECK LINER
or .035
.030
B. Changing Drive Roll Orientation
1. Flip lid open, then move release lever to the up position.
LID
RELEASE LEVER
2. Take wrench (10mm) and loosen drive roll while holding shaft
with flathead screw driver, then flip drive roll.
SHAFT
DRIVE ROLL
WIDE
3/64th
7
Making A Weld
MAGNUM 250 LX - OPERATING INSTRUCTIONS
1. Check that the spool gun power, control, and gas connections are
correct for the power source being used. Check that the gas supply
is turned on. Check wire spool for an adequate supply of wire.
2. See "Procedure Settings", below for wire feed speed and voltage
settings. Set these controls depending on the welding wire and
base metal thickness being used.
3. Connect work clamp to metal being welded. Work clamp must
make good electrical contact to the workpiece. The workpiece
must also be grounded as stated in "Arc Welding Safety
Precautions".
4. Connect power to welder and turn "ON".
5. Prepare to purge gas line by first releasing wire drive. Push wire
drive release lever to the UP position, to avoid feeding wire.
WARNING: Gun body and contact tip become electri-
cally energized when gun trigger is pressed and remain
so for several seconds after trigger is released.
6. Press and hold gun trigger for about 5 seconds to purge gas line.
If adjustable regulator or metering valve is installed, adjust gas
flow per, "Setting Gas Flow Rate".
7. Re-engage wire drive by pushing release lever to down position
to feed wire.
8. Momentarily squeeze trigger and verify that wire feeds properly.
Trim wire to approximately 1/4" (6 mm) from end of contact tip.
WARNING:When using an open arc process, it is neces-
sary to use correct eye, ear, head, and body protection.
9. Position gun over joint at 10° pushing angle. End of wire may be
lightly touching the work.
10. Lower welding helmet, close gun trigger, and begin welding.
Hold the gun so that the contact tip to work distance is about 1/2
inch (13 mm).
11. To stop welding, release the gun trigger and then pull the gun
away from the work after the arc goes out.
12. When no more welding is to be done, close valve on gas cylinder,
momentarily operate trigger to release gas pressure in line and
turn off power source.
13. Note that clogged tips can often be salvaged by peeling away
melted wire.
Procedure Settings
The following procedure settings for 4043 aluminum wire and argon
gas can be used as starting points for developing specific welding
procedures:
Wire Metal Wire Amps
Size Thickness Speed DC
in. (mm) ga. in. (mm) Arc Volts ipm (mpm) (+}
.030 (0.8) 22 .030 (0.8) 13-14
.035 (0.9) 22 .030 (0.8) 13-14
3/64(1.2) 10 .135 (3.5) 20-21
(1)
Short arc transfer.
20 .036 (1.0) 13-14
18 .048 (1.2) 14-15
16 .060 (1.6) 15-16
14 .075 (2.0) 16-17
12 .105 (2.5) 16-18
10 .135 (3.5) 24-26 460 (11.7) 110
3/16 (5.0) 24-26 500 (12.7) 150
1/4 (6.0) 28-29 560 (14.2) 180
3/8 (10.0) 28-30 600 (15.2) 200
20 .036 (1.0) 13-14
18 .048 (1.2) 13-14
16 .060 (1.6) 14-16
14 .075 (2.0) 14-16
12 .105 (2.5) 16-18
10 .135 (3.5) 24-26 410 (10.4) 110
3/16 (5.0) 24-26 450 (11.4) 150
1/4 (6.0) 26-28 530 (13.5) 180
3/8 (10.0) 26-29 560 (14.2) 200
1/2 (12.0) 26-30 600 (15.2) 220
3/16 (5.0) 20-21
1/4 (6.0) 27-28 250 (6.4) 180
3/8 (10.0) 25-30 260 (6.6) 200
1/2 (12.0) 25-31 270 (6.9) 220
3/4 (20.0) 25-31 290 (7.4) 250
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
200 (5.1) 40
240 (6.1) 40
290 (7.4) 50
340 (8.6) 60
370 (9.4) 70
430 (10.9) 90
150 (3.8) 40
175 (4.4) 40
215 (5.5) 50
250 (6.4) 60
270 (6.9) 70
320 (8.1) 90
180 (4.6) 110
220 (5.6) 150
Setting Gas Flow Rate
Gas handling systems having adjustable flow valves should be
set for the following argon flow rates, depending on base metal
thickness and welding position.
ARGON SHIELDING GAS FLOW RATES
Material Thickness Flow Rates
In Inches and (mm) Welding Position In cf/hr (l/mln)
1/16 (1.6 mm) Flat 30
(11.8)
3/32 to 3/16 Flat, Vertical, 35
(2.4 to 4.8 mm) Horizontal, Overhead (14)
1/4 to 3/8 Flat, Vertical, 35 (14)
(6.3 to 9.5 mm) Flat Vertical, 35 (16.5)
Horizontal, Overhead 40 (18.9)
3/4 (19 mm) Flat, Vertical 35 (16.5)
Horizontal, Overhead 40 (18.9)
8
MAGNUM 250 LX ACCESSORIES/MAINTENANCE
ACCESSORIES
The following accessories are available for the Magnum 250 LX
spool gun.
25 Foot Control Cable Extension
25 foot control lead with 7 pin male connector on machine side and
7 pin female connector on gun side. Allows the length of the spool
gun to be extended an additional 25 feet. (Note: Customer supplied
power cable and gas hose extension are also required) Order
K2519-1
.025 / .035 Steel Drive Roll
Features two grooves for feeding steel wire. The smaller groove
feeds .025 to.030 wire. The larger groove feeds 3/64 wire. Order
KP2518-1
.030 - .035 / 3/64th Aluminum Drive Roll
Features two grooves for feeding aluminum wire. The smaller
groove feeds .030 to .035 wire. The larger groove feeds 3/64th
wire. Order KP2518-2
Barrel Liner
Liner for feeding up to 3/64th wire. Order KP2521-1
Gas Diffuser
Diffuser designed to accept thread on gas nozzles Order KP52FN
Gas Nozzle
.38 Thread on Nozzle (Tip Recessed) Order KP23-37
.50 Thread on Nozzle (Tip Recessed) Order KP23-50
.62 Thread on Nozzle (Tip Recessed) Order KP23-62
.75 Thread on Nozzle (Tip Recessed) Order KP23-75
Contact Tips
Both standard duty and heavy duty contact tips are available in a
variety of sizes:
Standard Duty
.025 Steel Order KP14-23
.030 Steel or Aluminum Order KP14-30
3/64th Aluminum Order KP14A-364
Heavy Duty
.035 Steel or Aluminum Order KP14H-35
3/64th Aluminum Order KP14AH-364
MAINTENANCE
Safety Precautions
WARNING
• Do not operate with covers
removed.
• Disconnect input power from
welder before installing gun.
• Do not touch electrically hot
part.
• Only qualified persons
should install, use or service
this machine.
ELECTRIC SHOCK
can kill.
When finished welding, be sure to turn power source off and close
valve on gas cylinder.
WARNING
• Working with flying or falling objects can cause serious eye
injuries.
Routine Maintenance
Periodically blow out or vacum any metal wire shavings from Drive
Roll area.
Inspect and replace any worn wire on inlet guide or barrel liner.
NOTE: Oil and spray cleaners can contaminate electrode wire and
cause bad welds. They could also make wire drive rollers slip. Be
careful when using any of these liquids on spool gun.
Carefully clean gun with a cleaner that is safe for plastic. Apply
cleaner to rag and wipe gun. Do NOT spray cleaner on gun. Keep
cable dean. Oil, grease gasoline, paint, and solvents degrade cable
insulation.
Routine maintenance for consumable spare parts will depend on Duty Cycle and particular application.
• Protective eyeware such as safety specticals with side
shields or goggles must be worn at all times.
can cause eye injury.
9
MAGNUM 250 LX
Troubleshooting Guide
PROBLEM SYMPTOMS REMEDY
No arc, wire feed, or gas flow. 1. Cable connections loose. 1. Check all power connections.
2. Trigger switch loose or defective. 2. Fix switch or replace.
3. Welder not turned on. 3. Turn on welder power.
4. Welder not plugged in. 4. Plug in.
5. Cable or adapter cable damaged. 5. Inspect and replace
No arc, weak arc. 1. Poor ground connection to work. 1. Check ground connection.
2. Power cable connection loose. 2. Check connections; if defective,
replace cable or connectors.
3. Voltage set too low. 3. Adjust to proper voltage
4. Tip too large for wire size. 4. Change tip size.
5. Wire feed speed too slow. 5. Increase wire feed speed.
No wire feed. 1. Feeding small diameter wire with large 1. Change position of wire drive roller.
groove on drive roller.
2. Wire drive release open. 2. Close wire drive release.
3. Wire welded to tip. 3. Peel wire off tip or use new tip.
4. Wire spool empty. 4. Insert new spool.
5. Tip too small for wire. 5. Insert correct tip.
6. Kink or bend in wire. 6. Pull wire through tip or start new
wire end.
7. Spool cover binding. 7. Rotate spool cover slot to proper
position.
8. Control cable loose. 8. Check all connections.
9. Drive roller worn. 9. Replace.
10. Pressure roller stuck. 10. Replace or lubricate.
11. Roller spring loose or broken. 11. Replace.
Wire feed too fast or too slow. 1. Wrong wire speed set for work. 1. Adjust wire feed speed.
Low or no gas flow. Oxidation of work. 1. Gas flow not set right. 1. Set proper flow rate.
2. Cylinder out of gas. 2. Get new cylinder of gas.
3. Cylinder valve closed. 3. Open cylinder valve.
4. Leak in gas line. 4. Inspect and replace.
5. Leak in gun. 5. Check for missing gun tubes and/or
missing gun body cover.
6.Gas diffuser clogged 6. Blow out gas diffuser openings.
Oxidized work, arc unstable. 1. Wrong welding polarity. 1. Check polarity.
10
MAGNUM 250 LX
A
B
C
D
E
G
F
"W" CLOCKED
CONNECTOR
(VIEWED FROM FRONT OF CONNECTOR)
A
B
G
D
F
E
TORCH
FUNCTIONS
+-
MOTOR
TORCH
C
POT
TORCH
13
2
5K
CW
TORCH
TRIGGER
RED
BLACK
WHITE
GREEN
BLUE
BROWN
YELLOW/ORANGE
Troubleshooting Guide
TESTING THE TORCH
Motor Check. Remove the torch connector from the cabinet.
Using the torch Control Cable Connector, check the resistance across pins “A”
and “B” (motor leads). The resistance across the motor should be between 5-10
ohms. If an open circuit or short exist, check the motor leads and motor
independently.
Testing the Potentiometer. Using the torch Control Cable Connector, check the resistance across pin “D”
(wiper) and pin “C”. The resistance should vary from 5K - 0 ohms.
Check the resistance across pin “D” (wiper) and pin “G”. The resistance should
vary from 5K - 0 ohms.
Testing the Trigger Switch. Using the torch Control Cable Connector, check for continuity across pins “E”
and “F” when the trigger is pressed.
11
WARNING
Spanish
AVISO DE
PRECAUCION
● Do not touch electrically live parts or
electrode with skin or wet clothing.
● Insulate yourself from work and
ground.
● No toque las partes o los electrodos
bajo carga con la piel o ropa mojada.
● Aislese del trabajo y de la tierra.
● Keep flammable materials away.
● Mantenga el material combustible
fuera del área de trabajo.
● Wear eye, ear and body protection.
● Protéjase los ojos, los oídos y el
cuerpo.
French
ATTENTION
German
WARNUNG
Portuguese
ATENÇÃO
Japanese
Chinese
Korean
Arabic
● Ne laissez ni la peau ni des vête-
ments mouillés entrer en contact
avec des pièces sous tension.
● Isolez-vous du travail et de la terre.
● Berühren Sie keine stromführenden
Teile oder Elektroden mit Ihrem
Körper oder feuchter Kleidung!
● Isolieren Sie sich von den
Elektroden und dem Erdboden!
● Não toque partes elétricas e elec-
trodos com a pele ou roupa molhada.
● Isole-se da peça e terra.
● Gardez à l’écart de tout matériel
inflammable.
● Entfernen Sie brennbarres Material!
● Mantenha inflamáveis bem guarda-
dos.
● Protégez vos yeux, vos oreilles et
votre corps.
● Tragen Sie Augen-, Ohren- und Kör-
perschutz!
● Use proteção para a vista, ouvido e
corpo.
READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO
BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS
CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.
LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A
ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HERSTELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.
14
● Keep your head out of fumes.
● Use ventilation or exhaust to
remove fumes from breathing zone.
● Turn power off before servicing.
● Do not operate with panel open or
guards off.
WARNING
● Los humos fuera de la zona de res-
piración.
● Mantenga la cabeza fuera de los
humos. Utilice ventilación o
aspiración para gases.
● Gardez la tête à l’écart des fumées.
● Utilisez un ventilateur ou un aspira-
teur pour ôter les fumées des zones
de travail.
● Vermeiden Sie das Einatmen von
Schweibrauch!
● Sorgen Sie für gute Be- und
Entlüftung des Arbeitsplatzes!
● Mantenha seu rosto da fumaça.
● Use ventilação e exhaustão para
remover fumo da zona respiratória.
● Desconectar el cable de ali-
mentación de poder de la máquina
antes de iniciar cualquier servicio.
● Débranchez le courant avant l’entre-
tien.
● Strom vor Wartungsarbeiten
abschalten! (Netzstrom völlig öffnen; Maschine anhalten!)
● Não opere com as tampas removidas.
● Desligue a corrente antes de fazer
serviço.
● Não toque as partes elétricas nuas.
● No operar con panel abierto o
guardas quitadas.
● N’opérez pas avec les panneaux
ouverts ou avec les dispositifs de
protection enlevés.
● Anlage nie ohne Schutzgehäuse
oder Innenschutzverkleidung in
Betrieb setzen!
● Mantenha-se afastado das partes
moventes.
● Não opere com os paineis abertos
ou guardas removidas.
Spanish
AVISO DE
PRECAUCION
French
ATTENTION
German
WARNUNG
Portuguese
ATENÇÃO
Japanese
Chinese
Korean
Arabic
LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS
PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
15
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Loading...