Lincoln Electric IM879 User Manual

Safety Depends on You

RETURN TO MAIN MENU

Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thought­ful operation on your part. DO

NOT INSTALL, OPERATE OR
REPAIR THIS EQUIPMENT
WITHOUT READING THIS
MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED
THROUGHOUT. And, most

importantly, think before you act
and be careful.

RANGER™GXT

For Machines with Code Number 11269

IM879

March, 2006

Cleveland, Ohio 44117-1199 U.S.A. TEL: [phone] FAX: [phone] WEB SITE: www.lincolnelectric.com

OPERATOR’S MANUAL

Copyright © 2006 Lincoln Global Inc.

• World's Leader in Welding and Cutting Products •

• Sales and Service through Subsidiaries and Distributors Worldwide •

i

SAFETY

i

WARNING

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents
are known to the State of California to cause can­cer, birth defects, and other reproductive harm.

The Above For Diesel Engines

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.
KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you
purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box
351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available
from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.

The Above For Gasoline Engines

FOR ENGINE
powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance
work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes
outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame
welding arc or when the engine is running.
Stop the engine and allow it to cool before
refueling to prevent spilled fuel from vaporiz­ing on contact with hot engine parts and
igniting. Do not spill fuel when filling tank. If
fuel is spilled, wipe it up and do not start
engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in
position and in good repair.Keep hands, hair, clothing and
tools away from V-belts, gears, fans and all other moving
parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove
guards only when necessary and replace them when the
maintenance requiring their removal is complete.
Always use the greatest care when working near moving
parts.

___________________________________________________

1.f. Do not put your hands near the engine fan.
Do not attempt to override the governor or
idler by pushing on the throttle control rods
while the engine is running.

1.h. To avoid scalding, do not remove the
radiator pressure cap when the engine is
hot.

ELECTRIC AND
MAGNETIC FIELDS
may be dangerous

2.a. Electric current flowing through any conductor causes
localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and
welding machines

2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.

2.c. Exposure to EMF fields in welding may have other health
effects which are now not known.

2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:

2.d.1.

Route the electrode and work cables together - Secure
them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and

work cables. If the electrode cable is on your right
side, the work cable should also be on your right side.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenance
work, disconnect the spark plug wires, distributor cap or
magneto wire as appropriate.

2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.

2.d.5. Do not work next to welding power source.

Mar ‘95

ii

SAFETY

ii

ELECTRIC SHOCK can
kill.

3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.

In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.

ARC RAYS can burn.

4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.

FUMES AND GASES
can be dangerous.

5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases.When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. When

welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and below Threshold Limit Values (TLV)
using local exhaust or mechanical ventilation. In
confined spaces or in some circumstances, outdoors, a
respirator may be required. Additional precautions are
also required when welding on galvanized steel.

3.f.

Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.

3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

5.b.

Do not weld in locations near chlorinated hydrocarbon
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors
form phosgene, a highly toxic gas, and other irritating prod­ucts.

5.c. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.

5.d. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.

5.e. Also see item 1.b.

vapors

Mar ‘95

to

iii

SAFETY

iii

WELDING SPARKS can
cause fire or explosion.

6.a.

Remove fire hazards from the welding area.

If this is not possible, cover them to prevent

the welding sparks from starting a fire.

materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.

6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even
been “cleaned”. For information, purchase “Recommended
Safe Practices for the
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.

Sparks and spatter are thrown from the welding arc. Wear oil

6.f.
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.

6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate cir­cuits. This can create fire hazards or overheat lifting chains
or cables until they fail.

6.h. Also see item 1.c.

Remember that welding sparks and hot

though

they have

Preparation

for Welding and Cutting of

CYLINDER may explode
if damaged.

7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
process used and properly operating
regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from arc welding or cutting operations and

any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.

7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY
powered equipment.

8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.

8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.

8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.

Mar ‘95

iv

SAFETY

iv

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv­antes:

Sûreté Pour Soudage A L’Arc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand on

soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état
defonctionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.

6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.

8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de lev­age, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.

2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi qu’un verre blanc afin de se protéger les yeux du ray­onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de
l‘arc.

c. Protéger l’autre personnel travaillant à proximité au

soudage à l’aide d’écrans appropriés et non-inflammables.

4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan­talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.

PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la debranch­er à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur
place.

Mar. ‘93

for selecting a QUALITY product by Lincoln Electric. We want you

Thank You

to take pride in operating this Lincoln Electric Company product

••• as much pride as we have in bringing this product to you!

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.

Please record your equipment identification information below for future reference. This information can be
found on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

Where Purchased_________________________________________________________________________

vv

Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

“Product Registration”. Please complete the form and submit your registration.

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:

WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or
loss of life.

CAUTION

This statement appears where the information must be followed to avoid minor personal injury or damage to
this equipment.

vi

TABLE OF CONTENTS

Page

Installation.......................................................................................................................Section A

Technical Specifications.......................................................................................................A-1

Safety Precautions ........................................................................................................A-2

Machine Grounding.......................................................................................................A-2

Spark Arrester ...............................................................................................................A-2

Towing...........................................................................................................................A-2

Vehicle Mounting...........................................................................................................A-3

Pre-Operation Engine Service..............................................................................................A-3

Fuel, Oil, Battery Connections ......................................................................................A-3

Welding Cable Connections..........................................................................................A-4

Angle of Operation ........................................................................................................A-4

Lifting, Additional Safety Precautions............................................................................A-4

High Altitude Operation .................................................................................................A-4

Muffler Outlet Pipe ........................................................................................................A-4

Location and Ventilation................................................................................................A-5

Stacking ........................................................................................................................A-5

Connection of Wire Feeders .........................................................................................A-5

Connection of Tig Module .............................................................................................A-5

Additional Safety Precautions .......................................................................................A-5

Welding Operation Output, Auxiliary Power Receptacles, and Plugs .................................A-6

Motor Starting and Extension Cord Length Table ................................................................A-6

Electrical Device Used with the Ranger 10,000 ...................................................................A-7

Auxiliary Power While Welding, Standby Power Connections ............................................A-8

Premises Wiring ...................................................................................................................A-9

________________________________________________________________________________

Operation.........................................................................................................................Section B

Safety Precautions ...............................................................................................................B-1

General Description..............................................................................................................B-1

Welder Controls Function and Operation .............................................................................B-1

Polarity, Range and Control Switch......................................................................................B-2

Start in/Shutdown Instructions.....................................................................................................B-3

Starting the Engine........................................................................................................B-3

Safety Precautions ........................................................................................................B-3

Stopping the Engine......................................................................................................B-3

Break-In Period .............................................................................................................B-3

Welding Process ..................................................................................................................B-4

Stick (Constant Current) Welding..................................................................................B-4

TIG (Constant Current) Welding ..................................................................................B-4

Wire Feed Welding Processes (Constant Voltage)......................................................B-4

Arc Gouging ..................................................................................................................B-4

Summary of Welding Processes ...................................................................................B-5

________________________________________________________________________________

Accessories ........................................................................................................Section C

Optional Equipment...............................................................................................C-1

Recommended Equipment....................................................................................C-2

________________________________________________________________________

Maintenance ....................................................................................................Section D

Safety Precautions ................................................................................................D-1

Routine Engine Maintenance ..........................................................................D-1,D2

Engine Adjustments...............................................................................................D-3

Slip Rings ..............................................................................................................D-3

Battery Maintenance .......................................................................................D-3

Engine Maintenance Parts..............................................................................D-3

________________________________________________________________________

Troubleshooting..............................................................................................Section E

How to Use Troubleshooting Guide.......................................................................E-1

Troubleshooting Guide...................................................................................E-2, E-3

________________________________________________________________________

Wiring Diagrams & Dimension Print..............................................................Section F

Wiring and Connection Diagrams....................................................................F-1,F-2

Dimension Print .............................................................................................................F3

________________________________________________________________________

Parts List..................................................................................................................P505

________________________________________________________________________

vi

A-1

INSTALLATION

TECHNICAL SPECIFICATIONS - Ranger GXT (K2382-2 )

INPUT - GASOLINE ENGINE

Make/Model

Description

Horsepower

Operating

Speed (RPM)

Displacement

(cu.cm.)

cu. in.

Starting

System

A-1

Capacities

Kohler

CH20S

2 cylinder

4 Cycle

Air-Cooled

Gasoline

Engine.

Aluminum Alloy

with Cast Iron

Liners,

Electronic

Ignition

RATED OUTPUT @ 104°F (40°C)- WELDER

RATED OUTPUT @ 104°F (40°C)- GENERATOR

High Idle 3700

20 HP @

3600 RPM

AC Constant Current 250A / 25V / 100%

DC Constant Current 250A / 25V / 100%

DC Constant Voltage 250A / 25V / 100%

10,000 Watts Continuous, 60 Hz AC

11,000 Watts Peak, 60 Hz AC

Full Load 3500

Low Idle 2200

Welding Output

Auxiliary Power

120/240 Volts

38(624)

1

12VDC
Battery

Electric Start

Group 58

Battery
(435 cold
Cranking

Amps)

Fuel:
12 Gal (45.4 L)
Lubricating Oil:

2.0 Qts. (1.9 L)

RECEPTACLES AND CIRCUIT BREAKERS

RECEPTACLES

(2) 120VAC Duplex (5-20R)

(1) 120/240VAC Dual Voltage

Full KVA (14-50R)

AUXILIARY POWER CIRCUIT BREAKER

Two 20AMP for Two Duplex Receptacle

(1) 50AMP for Dual Voltage (2-pole)

BATTERY CHARGING CIRCUIT BREAKER

20AMP for Battery Charging Circuit

PHYSICAL DIMENSIONS

HEIGHT WIDTH DEPTH WEIGHT

30 in.** 21.5 in. 42.25 in.
762 mm 546 mm 1073 mm

1. Output rating in watts is equivalent to volt - amperes at unity factor.Output voltage is within +/-10% at all loads up to rated capacity.
When welding available auxiliary power will be reduced.

** Top of enclosure, add 6.00”(152mm) for exhaust.

RANGER GXT

602 lbs. (273kg)

A-2

INSTALLATION

A-2

SAFETY PRECAUTIONS

WARNING

Do not attempt to use this equipment until you
have thoroughly read the engine manufacturer’s
manual supplied with your welder. It includes
important safety precautions, detailed engine
starting, operating and maintenance instructions,
and parts lists.

------------------------------------------------------------------------

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts or
electrode with skin or wet clothing.

• Insulate yourself from work and
ground

• Always wear dry insulating gloves.

------------------------------------------------------------------------

ENGINE EXHAUST can kill.

• Use in open, well ventilated areas or
vent exhaust outside.

------------------------------------------------------------------------

MOVING PARTS can injure.

• Do not operate with doors open or
guards off.

• Stop engine before servicing.

• Keep away from moving parts.

------------------------------------------------------------------------

See additional warning information at

front of this operator’s manual.

-----------------------------------------------------------

MACHINE GROUNDING

When this welder is mounted on a truck or trailer, it’s
frame must be electrically bonded to the metal frame
of the vehicle. Use a #8 or larger copper wire connect­ed between the machine grounding stud and the
frame of the vehicle.
Where this engine driven welder is connected to
premises wiring such as that in your home or shop, it’s
frame must be connected to the system earth ground.
See further connection instructions in the section enti­tled “Standby Power Connections”, as well as the arti­cle on grounding in the latest National Electrical Code
and the local code.

In general, if the machine is to be grounded, it should
be connected with a #8 or larger copper wire to a solid
earth ground such as a metal water pipe going into
the ground for at least ten feet and having no insulat­ed joints, or to the metal framework of a building
which has been effectively grounded. The National
Electrical Code lists a number of alternate means of
grounding electrical equipment. A machine grounding
stud marked with the symbol is provided on the
front of the welder.

SPARK ARRESTER

Some federal, state, or local laws may require that
gasoline engines be equipped with exhaust spark
arresters when they are operated in certain locations
where unarrested sparks may present a fire hazard.
The standard muffler included with this welder does
not qualify as a spark arrester. When required by local
regulations, the K1898-1 spark arrester must be
installed and properly maintained.

Because this portable engine driven welder or genera­tor creates it’s own power, it is not necessary to con­nect it’s frame to an earth ground, unless the machine
is connected to premises wiring (your home, shop,
etc.).

WARNING

To prevent dangerous electric shock, other equip­ment to which this engine driven welder supplies
power must:

• be grounded to the frame of the welder using a

grounded type plug, or be double insulated.

Do not ground the machine to a pipe that carries
explosive or combustible material.

------------------------------------------------------------------------

RANGER GXT

CAUTION

An incorrect arrester may lead to damage to the
engine or adversely affect performance.

------------------------------------------------------------------------

TOWING

The recommended trailer for use with this equipment
for road, in-plant and yard towing by a vehicle
Lincoln’s K957-1. If the user adapts a non-Lincoln
trailer, he must assume responsibility that the method
of attachment and usage does not result in a safety
hazard nor damage the welding equipment. Some of
the factors to be considered are as follows:

1. Design capacity of trailer vs. weight of Lincoln
equipment and likely additional attachments.

2. Proper support of, and attachment to, the base of

the welding equipment so there will be no undue
stress to the framework.

(1)

is

A-3

3. Proper placement of the equipment on the trailer to
insure stability side to side and front to back when
being moved and when standing by itself while
being operated or serviced.

4. Typical conditions of use, i.e., travel speed; rough-

ness of surface on which the trailer will be operated;
environmental conditions.

INSTALLATION

A-3

FUEL

Fill the fuel tank with clean, fresh, lead-free gasoline.
Observe fuel gauge while filling to prevent overfilling.

WARNING

5. Conformance with federal, state and local laws

(1) Consult applicable federal, state and local laws regarding specific

requirements for use on public highways.

VEHICLE MOUNTING

(1)

WARNING

Improperly mounted concentrated loads may
cause unstable vehicle handling and tires or other
components to fail.

• Only transport this Equipment on serviceable
vehicles which are rated and designed for such
loads.

• Distribute, balance and secure loads so vehicle
is stable under conditions of use.

• Do not exceed maximum rated loads for compo­nents such as suspension, axles and tires.

• Mount equipment base to metal bed or frame of
vehicle.

• Follow vehicle manufacturer’s instructions.

------------------------------------------------------------------------

PRE-OPERATION SERVICE

• Damage to the fuel tank may cause
fire or explosion. Do not drill holes
in the RANGER GXT base or weld to
the RANGER GXT base.

-----------------------------------------------------------------------

OIL

LUBRICATION SYSTEM CAPACITY

(INCLUDING FILTER)

Kohler CH20S - 2.0 Quarts (1.9 Liters)

The RANGER GXT is shipped with the engine
crankcase filled with SAE 10W-30 oil. Check the oil
level before starting the engine. If it is not up to the full
mark on the dip stick, add oil as required. Make cer­tain that the oil filler cap is tightened securely. Refer to
the engine Owner’s Manual for specific oil recommen­dations.

BATTERY CONNECTIONS

CAUTION

CAUTION

READ the engine operating and maintenance
instructions supplied with this machine.

WARNING

• Stop engine while fueling.

• Do not smoke when fueling.

• Keep sparks and flame away
from tank.

• Do not leave unattended while
fueling.

• Wipe up spilled fuel and allow

GASOLINE

can cause fire
or explosion.

fumes to clear before starting
engine.

• Do not overfill tank, fuel expan­sion may cause overflow.

GASOLINE FUEL ONLY

------------------------------------------------------------------------

Use caution as the electrolyte is a strong
acid that can burn skin and damage eyes.

-----------------------------------------------------------------------

This welder is shipped with the negative battery cable
disconnected. Make sure that the Engine Switch is in
the “STOP” position and attach the disconnected
cable securely to the negative battery terminal before
attempting to operate the machine. If the battery is
discharged and does not have enough power to start
the engine, see the battery charging instructions in the
Battery section.

NOTE: This machine is furnished with a wet charged
battery; if unused for several months, the battery may
require a booster charge. Be careful to charge the bat­tery with the correct polarity.

RANGER GXT

A-4

INSTALLATION

WELDING OUTPUT CABLES

With the engine off, connect the electrode and work
cables to the studs provided. These connections
should be checked periodically and tightened if neces­sary. Loose connections will result in overheating of
the output studs.

When welding at a considerable distance from the
welder, be sure you use ample size welding cables.
Listed below are copper cable sizes recommended for
the rated current and duty cycle. Lengths stipulated
are the distance from the welder to work and back to
the welder again. Cable sizes are increased for
greater lengths primarily for the purpose of minimizing
cable voltage drop.

TOTAL COMBINED LENGTH OF

ELECTRODE AND WORK CABLES

250 Amps

100% Duty Cycle

A-4

ADDITIONAL SAFETY PRECAUTIONS

WARNING

• Lift only with equipment of
adequate lifting capacity.

• Be sure machine is stable
when lifting.

• Do not lift this machine using
lift bail if it is equipped with a
heavy accessory such as trail­er or gas cylinder.

FALLING • Do not lift machine if lift bail is

EQUIPMENT can damaged.

cause injury. • Do not operate machine while

suspended from lift bail.

------------------------------------------------------------------------

HIGH ALTITUDE OPERATION

0-100 Ft. (0-31m)

100-150 Ft. (31-46m)

150-200 Ft. (46-61m)

1 AWG

1 AWG

1/0 AWG

ANGLE OF OPERATION

Internal combustion engines are designed to run in a
level condition which is where the optimum perfor­mance is achieved. The maximum angle of operation
for the engine is 15 degrees from horizontal in any
direction. If the engine is to be operated at an angle,
provisions must be made for checking and maintain­ing the oil at the normal (FULL) oil capacity in the
crankcase in a level condition.

When operating at an angle, the effective fuel capacity
will be slightly less than the specified 12 Gal. (45 L).

LIFTING

The RANGER GXT weighs approximately
685lbs.(411kg) with a full tank of gasoline. A lift bail is
mounted to the machine and should always be used
when lifting the machine.

If the RANGER GXT will be consistently operated at
altitudes above 5000 ft(1524m), a carburetor jet
designed for high altitudes should be installed. This
will result in better fuel economy, cleaner exhaust, and
longer spark plug life. It will not
which is decreased at higher altitudes. Engine horse­power is reduced by 3.5% per 1000 ft.(305m) for alti­tudes above 377 ft.(115m).

give increased power

CAUTION

Do not operate a RANGER GXT with a high alti­tude jet installed at altitudes below 5000 ft.
(1524m). This will result in the engine running too
lean and result in higher engine operating temper­atures which can shorten engine life.

-----------------------------------------------------------------------

Contact your local Kohler Authorized Dealer for high
altitude jet kits that are available from the engine man­ufacturer.

MUFFLER OUTLET PIPE

Using the clamp provided secure the outlet pipe to the
outlet tube with the pipe positioned such that it will
direct the exhaust in the desired direction. Tighten
using a 9/16” socket or wrench.

RANGER GXT