Lincoln Electric LN -15, IM823-A User Manual
IM823-A
N80
RETURN TO MAIN MENU
LN ™-15 WIRE FEEDER
For use with machines having Code Number : 11033, 11035, 11600
Safety Depends on You
Lincoln arc welding a n d c u t t i n g
equipment is designed and built with
safety in mind. However, your overall
safety can be increased by proper
installation ... and thoughtful operation on your part. DO NOT
INSTALL, OPERATE OR REPAIR
THIS E Q U IPME N T WI T H O U T
READING THIS M A NUA L AND
THE SAFET Y P R E C A U T I O NS
CONTAINED THROUGHOUT. And,
most importantly, think before you
act and be careful.
March, 2010
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
IEC 60974-5
EN 60974-5
OPERATOR’S MANUAL
Copyright © Lincoln Global Inc.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
i
SAFETY
WARNING
CALIFORNIA PROPOSITION 65 WARNINGS
Diesel engine exhaust and some of its constituents
are known to the State of California to cause cancer, birth defects, and other reproductive harm.
The Above For Diesel Engines
ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.
KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you
purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box
351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available
from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
The Above For Gasoline Engines
i
FOR ENGINE
powered equipment.
1.a. Turn the engine off before troubleshooting and maintenance
work unless the maintenance work requires it to be running.
____________________________________________________
1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes
outdoors.
____________________________________________________
1.c. Do not a dd t he f uel near an open fl ame
welding arc or when the engine is running.
Stop the engine and allow it to cool before
refueling to prevent spilled fuel from vaporizing on contact wit h hot engine parts and
igniting. Do not spill fuel when filling tank. If
fuel is spilled, wipe it up and do not start
engine until fumes have been eliminated.
____________________________________________________
1.d. Keep all equipment safety guards, covers and devices in
position and in good repair.Keep hands, hair, clothing and
tools away from V-belts, gears, fans and all other moving
parts when starting, operating or repairing equipment.
____________________________________________________
1.e. In some cases i t may be nece ssary to remo ve safety
gu a r d s to perfor m requi r e d mai n t e n a n c e . R e m o v e
guards only when necessary and replace them when the
ma i n t e n a n c e r e q u iring their removal is comple t e .
Always use the greatest care when working near moving
parts.
___________________________________________________
1.f. Do not put your hands near the engine fan.
Do not attempt to override the governor or
idler by pushing on the throttle control rods
while the engine is running.
1.h. To avoid scalding, do not remove the
radiator pressure cap when the engine is
hot.
ELECTRIC AND
MAGNETIC FIELDS
may be dangerous
2.a. Electr ic c urrent flowi ng thr ough any conduc tor causes
localized Electric and Magnetic Fields (EMF). Welding
current creates EMF f ields around welding c ables and
welding machines
2.b. EMF f iel ds m ay int erf ere wi th s ome pa cem ake rs, and
welders having a pacemaker should consult their physician
before welding.
2.c. Exposure to EMF fields in welding may have other health
effects which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1.
Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Nev er coi l the ele ctrode lead aroun d your bo dy.
2.d.3. Do not place your body between the electrode and
work cables. If the electrode cable is on your right
side, the work cable should also be on your right side.
___________________________________________________
1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenance
work, disconnect the spark plug wires, distributor cap or
magneto wire as appropriate.
2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.
2.d.5. Do not work next to welding power source.
Mar ‘95
ii
SAFETY
ii
ELECTRIC SHOCK can
kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet c lothing . Wea r dry , hole-free
gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
In addition to the normal safety precautions, if welding
mu s t be performed u nder electri c a l l y hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrod e reel, weld ing hea d, n oz zle or sem iautomatic
welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f.
Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. N eve r simul tan eou sly tou ch elec tri call y “hot” pa rts o f
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
ARC RAYS can burn.
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fum es and gases
hazardous to health. Avoid breathing these
fume s and ga ses. Whe n weldin g, k eep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
fumes and gases away from the breathing zone. When
we l d i n g wi t h elect r o d e s whi c h requi r e speci a l
ve n t ilation such as st ainless or hard fa cing (se e
instruc tions on co ntainer or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and within applicable OSHA PEL and
ACGIH TLV limits using local exhaust or mechanical
ventilation. In confined spaces or in some circumst a n ces, out d o ors, a re spirator may be re q uired.
Additional precautions are also required when welding
on galvanized steel.
5. b. The operation of welding fume control equipment is affected
by various factors including proper use and positioning of
the equipment, maintenance of the equipment and the specific welding procedure and application involved. Worker
exposure level should be checked upon installation and
periodically thereafter to be certain it is within applicable
OSHA PEL and ACGIH TLV limits.
5.c.
Do not weld in locations near chlorinated hydrocarbon
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors
form phosgene, a highly toxic gas, and other irritating products.
5.d. Shielding gases used for arc welding can displace air and
caus e inju ry or dea th. Al ways use e nou gh v ent ilation,
especially in confined areas, to insure breathing air is safe.
vapors
to
5.e. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
ma t e r i a l s a f e t y d a t a s h eet (MSDS) and follo w yo u r
employer’s safety practices. MSDS forms are available from
yo u r w e l d ing dist r i b u t o r or from t h e manufactu r e r .
5.f. Also see item 1.b.
Jan ‘09
iii
SAFETY
iii
WELDING and CUTTING
SPARKS can
cause fire or explosion.
6.a.
Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
Re m e m b e r th a t weldin g sparks and ho t
materials from welding can easily go through small cracks
an d op e ning s to adja c ent areas . Av o id we ldin g ne a r
hydraulic lines. Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z4 9.1) a nd t he o pe rating infor mation for the
equipment being used.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even
been “cleaned”. For information, purchase “Recommended
Safe Practices for the
Co n t a i n e r s and P i p i n g That H a v e H eld Ha z a r d o u s
Substances”, AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
Sparks and spatter are thrown from the welding arc. Wear oil
6.f.
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate circuits. This can create fire hazards or overheat lifting chains
or cables until they fail.
6.h. Also see item 1.c.
the wel ding sparks fr om sta rting a fire.
though
they have
Preparation
for Welding and Cutting of
CYLINDER may explode
if damaged.
7.a. Us e o n l y compress e d g a s cylinders
containing the correct shielding gas for the
pr o c e s s us e d and properl y operat i n g
re g u l a t o r s d e signed for t h e g a s a n d
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cyli nders i n an up right p osi tio n secu rel y
chained to an undercarriage or fixed support.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected to
physical damage.
• A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. R ead and fol l ow the inst r uct i ons on comp r ess ed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
FOR ELECTRICALLY
powered equipment.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
6.I. Read and follow NFPA 51B “ Standard for Fire Prevention
During Welding, Cutting and Other Hot Work”, available
from NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma
022690-9101.
6.j. Do not use a welding power source for pipe thawing.
Refer to http://www.lincolnelectric.com/safety for additional safety information.
Jan ‘09
iv
SAFETY
iv
PRÉCAUTIONS DE SÛRETÉ
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suivantes:
Sûreté Pour Soudage A L’Arc
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état
defonctionnement.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la mas se. Un court-cir cu it accid en tal peu t provo qu er un
échauffement et un risque d’incendie.
8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de levage, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoya ge ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.
PRÉCAUTIONS DE SÛRETÉ POUR
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi qu’un verre blanc afin de se protéger les yeux du rayonnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de
l‘arc.
c. Protéger l’aut re p erson nel trav ailla nt à pr oximi té a u
soudage à l’aide d’écrans appropriés et non-inflammables.
4. De s gouttes de laitier en fus io n sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pantalons sans revers, et chaussures montantes.
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
3. Avant de faires des travaux à l’interieur de poste, la debrancher à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.
Mar. ‘93
v
SAFETY
v
vi
SAFETY
vi
vii
TThhaannkk YYoouu
vii
for selecting a QUALITY product by Lincoln Electric. We want you
to take pride in operating this Lincoln Electric Company product
••• as much pride as we have in bringing this product to you!
The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equipment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln
Electric for advice or information about their use of our products. We respond to our customers based on the best information in our possession at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such information or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose,
with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or
correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any
warranty with respect to the sale of our products.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control
of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in
applying these types of fabrication methods and service requirements.
Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com
for any updated information.
CUSTOMER ASSISTANCE POLICY
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.
Please record your equipment identification information below for future reference. This information can be
found on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information you
On-Line Product Registration
- Register your machine with Lincoln Electric either via fax or over the Internet.
• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.
• For On-Line Registration: Go to our
“Product Registration”. Please complete the form and submit your registration.
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then
WARNING
This statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.
CAUTION
This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.
viii
TABLE OF CONTENTS
Page
Installation.......................................................................................................................Section A
Technical Specifications.......................................................................................................A-1
Safety Precautions ...............................................................................................................A-2
Location................................................................................................................................A-2
Work Clip Lead.....................................................................................................................A-2
High Frequency Protection...................................................................................................A-2
Weld Cable Connections......................................................................................................A-3
Electrode Connection ...........................................................................................................A-3
Work Connection..................................................................................................................A-3
Power Source Connection....................................................................................................A-3
Engine Drive Power Source Connection ..............................................................................A-3
Connection Diagrams...........................................................................................................A-4
Gun and Cable Assemblies..................................................................................................A-5
Electrode Polarity .................................................................................................................A-5
Connections .........................................................................................................................A-5
Procedure to Install Drive Rolls and Wire Guides ................................................................A-5
Feed Wire Electrode.............................................................................................................A-6
________________________________________________________________________________
Operation.........................................................................................................................Section B
Safety Precautions ...............................................................................................................B-1
Graphic Symbols that appear on this Machine or in this Manual .........................................B-1
General Description..............................................................................................................B-2
Duty Cycle ............................................................................................................................B-2
Recommended Processes ...................................................................................................B-2
Process Limitations ..............................................................................................................B-2
Equipment Limitations ..........................................................................................................B-2
Operational Features and Controls .....................................................................................B-2
Case Front Controls .............................................................................................................B-3
83% Procedure.....................................................................................................................B-3
LN™-15 Power-Up Sequence ......................................................................................B-4, B-5
Internal Controls ...................................................................................................................B-5
Spring Tension Arm..............................................................................................................B-5
Wire Drive Configuration ......................................................................................................B-6
Cold Feed/Gas Purge Switch ...............................................................................................B-6
2 Step-Trigger Interlock Switch ............................................................................................B-7
Flow Meter............................................................................................................................B-7
Spindle Brake .......................................................................................................................B-7
Shielding Gas Connection....................................................................................................B-7
Constant Current Operation .................................................................................................B-8
Setting Arc Sensing wire Feed Speed For Constant Current Operation ..............................B-9
Making a Weld....................................................................................................................B-10
________________________________________________________________________________
viii
Accessories ....................................................................................................................Section C
Factory Installed Equipment.................................................................................................C-1
Electrode, K-Kit used ...........................................................................................................C-1
________________________________________________________________________________
Maintenance....................................................................................................................Section D
Safety Precautions ...............................................................................................................D-1
Routine Maintenance ...........................................................................................................D-1
Periodic Maintenance...........................................................................................................D-1
Calibration Specification.......................................................................................................D-1
________________________________________________________________________________
Troubleshooting .................................................................................................................Section E
Safety Precautions ...............................................................................................................E-1
How to Use Troubleshooting Guide .....................................................................................E-1
Troubleshooting Guide ...........................................................................................E-2 thru E-4
________________________________________________________________________________
Wiring Diagram & Dimension Prints .............................................................................Section F
________________________________________________________________________________
Parts Pages ............................................................................................................................P-482
_______________________________________________________________________
________
A-1
INSTALLATION
TECHNICAL SPECIFICATIONS – LN™-15 (K1870-1), (K1870-2 CE)
INPUT VOLTAGE
15-110 VDC (5 Amps Maximum)
Across the Arc Model
RATED CURRENT
300 Amps 60% Duty Cycle
250 Amps 100% Duty Cycle
ELECTRODE DIAMETERS and SPEED RANGE
Electrode Size Speed Range
A-1
Solid Electrode
Steel
Flux Cored
Electrode
0.023 - 0.052" 50 - 700 in/min
(0.6 - 1.3 mm) (1.3 - 17.8 m/min)
0.0345 - 5/64" 50 - 400 in/min
(0.9 - 2.3 mm) (1.3 - 10.1 m/min)
PHYSICAL DIMENSIONS
HEIGHT WIDTH DEPTH WEIGHT
12.7 Inches 8.7 Inches 23 Inches 30lbs
(323 mm) (221mm) (584 mm) (14kg)
TEMPERATURE RANGE
OPERATION: - 20oC to +50oC (- 4oF to +122oF)
o
STORAGE: - 40
C to +70oC (- 40oF to +185oF)
SPOOL SIZE CAPABILITY
8 (200mm) Dia. x 4 (100mm)
Wide Spools including
AWS 8 DIA. (10-15lbs)
JIS S-3 200mm max. (5 - 7 kg)
DIN 200 (5 kg)
LN™-15 ACROSS THE ARC MODEL & (CE)
A-2
SAFETY PRECAUTIONS
WARNING
INSTALLATION
The work clip lead attached to the front of the LN™15 must be connected directly to the work using the
spring clip on the end of the lead.
A-2
ELECTRIC SHOCK CAN KILL.
• ONLY QUALIFIED PERSONNEL
SHOULD PERFOR M THIS
INSTALLATION.
• Turn off input power to the power
source at the disconnect switch
or fuse box before working on
this equipment. Turn off the input power to any
other equipment connected to the welding
system at the disconnect switch or fuse box
before working on the equipment.
• Do not touch electrically hot parts.
• Do not touch metal portions of the LN™-15
work lead clip when the welding power source
is on.
• Do not connect the LN™-15 to a non-Lincoln
TIG power source, a SQUARE WAVE TIG power
source, or a PLASMA CUTTING power source.
-------------------------------------------------------------------
LOCATION
The LN™ - 1 5 sh o u ld be po s i tioned upright on a
horizontal surface. Do not submerge the LN™-15 in
water. The best practice is to keep the wire feeder in
a dry environment. When working outdoors in severe
wet weather, place the LN™-15 with the door facing
up.
If the work clip lead is not connected, the LN™-15 will
not operate.
The work clip lead also serves as a work sensing lead
for the LN™-15. If the work clip lead is extended by
the user beyond the standard 15' (4.6m) length, the
voltmeter reading will be lower than the actual arc
volts due to resistance in the extended lead. To minimize the error, the following lead size is recommended for the maximum extended lengths shown.
AWG Max. Length
#14 25 ft (7.6m)
#12 50 ft (15.2m)
#10 100 ft (30.5m)
#6 200 ft (61.0m)
CORRECT WORK CLIP ATTACHED TO WORK
WARNING
WORK CLIP LEAD
ELECTRIC SHOCK CAN KILL.
• ONLY QUAL IFIED PE RSON NEL
SHOULD PER FORM THIS
INSTALLATION.
• Do not touch metal portions of the
LN™-15 work clip lead when
the welding power source is on. The work clip
lead is electrically "hot" to work if the input
electrode cable to the LN™-15 is electrically
"hot", even if the gun trigger is off. Care should
be taken to only handle the LN™-15 work clip
lead by its nonmetal insulated portions and/or
the welding power source should be turned off
before handling the work clip.
• Do not attach the work clip lead to the roll cage
or bottom skids of the LN™-15.
• Attach the work clip only to the work piece.
-------------------------------------------------------------------
** The work clip lead is present only on Across-the-
Arc models.
LN™-15 ACROSS THE ARC MODEL & (CE)
INCORRECT WORK CLIP ATTACHED TO ROLL CAGE
HIGH FREQUENCY PROTECTION
CAUTION
To prevent possible damage to the LN™-15, do
not connect the LN™-15 to non-Lincoln TIG or
SQUARE WAVE power sources. TIG high frequency should never be applied to the LN™-15.
-------------------------------------------------------------------
Locate the LN™-15 away fr o m radio c o n t r o l l e d
machinery. The normal operation of the LN™-15 may
adversely affect the operation of RF controlled equipment, which may result in bodily injury or damage to
the equipment total.
A-3
INSTALLATION
A-3
WELD CABLE CONNECTIONS
WARNING
ELECTRIC SHOCK CAN KILL.
• Only a qualified electrician should
connect the electrode leads to the
LN™-15. Connections should be
made in accordance with all local
and national electrical cod es.
Failure to do so may result in bodily injury or death.
-------------------------------------------------------------------
The size of the electrode cable and work cable must
be sufficient for the maximum weld current and total
cable length used.
To avoid interference problems with other equipment
and to achieve the best possible operation, route all
cables directly to the work or wire feeder. Avoid
excessive lengths and do not coil excess cable. Be
sure the connection to the work makes tight metal-tometal electrical contact. (See Table A.1)
TABLE A.1
CAUTION
To prevent possible damage to the LN™-15, do
not connect the LN™-15 to non-Lincoln TIG or
square wave power sources. TIG high frequency
should never be applied to the LN™-15.
------------------------------------------------------------------------------------------
ENGINE DRIVE POWER SOURCE
CONNECTION
The LN™-15 has an internal contactor and the electrode is not energized until the gun trigger is closed.
When the gun trigger is closed the wire will begin to
feed and the welding process is started.
1. Shut the welder off.
2. For electrode Positive polarity welding, connect the
electrode cable to the "+" terminal of the welder
and work cable to the "-" terminal of the welder. For
Electrode Negative welding, connect the electrode
cable to the "-" terminal of the welder and work
cable to the "+" terminal of the welder.
Weld Current Total Cable Length
60% Duty (electrode cable + work cable)
Cycle 50 - 100' 100 - 150' 150 - 200' 200 - 250'
(15-30 m) (30 - 46m) (46 - 61m) (61m - 76m)
200 Amps 2 AWG 2 AWG 1 AWG 1/0
300 Amps 1 AWG 1 AWG 1/0 2/0
400 Amps 2/0 2/0 3/0 3/0
ELECTRODE CONNECTION
Route the electrode cable through the strain relief in
the rear of the case. Connect the electrode cable to
the LN™-15 input stud using the mounting hardware
provided. Secure the cable by tightening the strain
relief.
All domestic models are supplied with pigtail for customers that prefer to make a taped and bolted connection externally. CE models have a male twist connector for the electrode connection.
WORK CONNECTION
Connect a work lead of sufficient size between the
proper output stud on the power source and the work.
Be sure the connection to the work makes tight metal
to metal electrical contact. Poor work lead connections can result in poor welding performance.
3. Attach the work clip lead from the front of the LN™-
15 to work using the spring clip at the end of the
lead. This is a control lead to supply current to the
wire feeder motor; it does not carry welding current.
4. Set the MODE switch on the engine drive to CV-
WIRE.
5. Set the WELD TERMINALS switch to WELD TER-
MINALS ON.
6. Set the WIRE FEEDER VOLTMETER switch to
either "+" or "-" as required by the electrode polarity
being used.
7. Set the ARC CONTROL knob to "0" initially and
adjust to suit.
8. Set the IDLE swit c h to the AUTO posi t ion .
Important: Some older engine drives may require
the IDLE switch to be in the HIGH position for proper LN™-15 operation.
POWER SOURCE CONNECTION
The LN™-15 can be used with any DC welding power
source. A constant voltage power source is recommend; however, the LN™-15 can also be used with a
constant current power source as long as the open
circuit voltage is less than 110VDC.
LN™-15 ACROSS THE ARC MODEL & (CE)
Loading...