Lincoln Electric IM408 User Manual

Safety Depends on You

RETURN TO MAIN MENU

Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thought­ful operation on your part. DO

NOT INSTALL, OPERATE OR
REPAIR THIS EQUIPMENT
WITHOUT READING THIS
MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED
THROUGHOUT. And, most

importantly, think before you act
and be careful.

MAGNUM™SG

SPOOL GUN

IM408

February, 2005

Cleveland, Ohio 44117-1199 U.S.A. TEL: [phone] FAX: [phone] WEB SITE: www.lincolnelectric.com

OPERATOR’S MANUAL

Copyright © 2005 Lincoln Global Inc.

• World's Leader in Welding and Cutting Products •

• Sales and Service through Subsidiaries and Distributors Worldwide •

i

SAFETY

i

WARNING

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents
are known to the State of California to cause can­cer, birth defects, and other reproductive harm.

The Above For Diesel Engines

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.
KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you
purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box
351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available
from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.

The Above For Gasoline Engines

FOR ENGINE
powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance
work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes
outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame
welding arc or when the engine is running.
Stop the engine and allow it to cool before
refueling to prevent spilled fuel from vaporiz­ing on contact with hot engine parts and
igniting. Do not spill fuel when filling tank. If
fuel is spilled, wipe it up and do not start
engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in
position and in good repair.Keep hands, hair, clothing and
tools away from V-belts, gears, fans and all other moving
parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove
guards only when necessary and replace them when the
maintenance requiring their removal is complete.
Always use the greatest care when working near moving
parts.

___________________________________________________

1.f. Do not put your hands near the engine fan.
Do not attempt to override the governor or
idler by pushing on the throttle control rods
while the engine is running.

1.h. To avoid scalding, do not remove the
radiator pressure cap when the engine is
hot.

ELECTRIC AND
MAGNETIC FIELDS
may be dangerous

2.a. Electric current flowing through any conductor causes
localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and
welding machines

2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.

2.c. Exposure to EMF fields in welding may have other health
effects which are now not known.

2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:

2.d.1.

Route the electrode and work cables together - Secure
them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and

work cables. If the electrode cable is on your right
side, the work cable should also be on your right side.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenance
work, disconnect the spark plug wires, distributor cap or
magneto wire as appropriate.

2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.

2.d.5. Do not work next to welding power source.

Mar ‘95

ii

SAFETY

ii

ELECTRIC SHOCK can
kill.

3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.

In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.

ARC RAYS can burn.

4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.

FUMES AND GASES
can be dangerous.

5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases.When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. When

welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and below Threshold Limit Values (TLV)
using local exhaust or mechanical ventilation. In
confined spaces or in some circumstances, outdoors, a
respirator may be required. Additional precautions are
also required when welding on galvanized steel.

3.f.

Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.

3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

5.b.

Do not weld in locations near chlorinated hydrocarbon

coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors
form phosgene, a highly toxic gas, and other irritating
products.

5.c. Shielding gases used for arc welding can displace air and

cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.

5.d. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the

material safety data sheet (MSDS) and follow your

employer’s safety practices. MSDS forms are available from

your welding distributor or from the manufacturer.

5.e. Also see item 1.b.

Mar ‘95

vapors

to

iii

SAFETY

iii

WELDING SPARKS can
cause fire or explosion.

6.a.

Remove fire hazards from the welding area.

If this is not possible, cover them to prevent

the welding sparks from starting a fire.

materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.

6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even
been “cleaned”. For information, purchase “Recommended
Safe Practices for the
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.

Sparks and spatter are thrown from the welding arc. Wear oil

6.f.
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.

6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate cir­cuits. This can create fire hazards or overheat lifting chains
or cables until they fail.

6.h. Also see item 1.c.

Remember that welding sparks and hot

though

they have

Preparation

for Welding and Cutting of

CYLINDER may explode
if damaged.

7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
process used and properly operating
regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from arc welding or cutting operations and

any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.

7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY
powered equipment.

8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.

8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.

8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.

Mar ‘95

iv

SAFETY

iv

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv­antes:

Sûreté Pour Soudage A L’Arc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand on

soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état
defonctionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.

6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.

8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de lev­age, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.

2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi qu’un verre blanc afin de se protéger les yeux du ray­onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de
l‘arc.

c. Protéger l’autre personnel travaillant à proximité au

soudage à l’aide d’écrans appropriés et non-inflammables.

4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan­talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.

PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la debranch­er à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur
place.

Mar. ‘93

for selecting a QUALITY product by Lincoln Electric. We want you

Thank You

to take pride in operating this Lincoln Electric Company product

••• as much pride as we have in bringing this product to you!

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.

Please record your equipment identification information below for future reference. This information can be
found on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

vv

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

“Product Registration”. Please complete the form and submit your registration.

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:

WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or
loss of life.

CAUTION

This statement appears where the information must be followed to avoid minor personal injury or damage to
this equipment.

vi

TABLE OF CONTENTS

Page

SAFETY PRECAUTIONS ..............................................................................................i thru iv

INTRODUCTORY INFORMATION ..........................................................................................v

TABLE OF CONTENTS ..........................................................................................................vi

PART A ................................................................................................................................1

PRODUCT DESCRIPTION. .............................................................................................1

SPECIFICATIONS............................................................................................................1

RECOMMENDED PROCESSES AND EQUIPMENT ......................................................1

PART B ................................................................................................................................2

INSTALLATION ................................................................................................................2

SAFETY PRECAUTIONS .............................................................................................2

UNPACKING THE SPOOL GUN ..................................................................................2

SPOOL GUN FAMILIARIZATION .................................................................................2

SPOOL GUN FAMILIARIZATION DIAGRAM............................................................3

SPOOL GUN INSTALLATION ......................................................................................3

CONNECTION TO K488 MAGNUM SG CONTROL MODULE ..............................3

INSTALLATION TO LINCOLN SP-250 ...................................................................4

INSTALLATION TO LINCOLN SP150 ....................................................................4

CONTROL CIRCUIT DIAGRAMS...........................................................................5

INSTALLATION TO LINCOLN SP-200 ...................................................................6

INSTALLATION TO SIMILAR WELDERS WITH WIRE FEED CONTROL.............7

vi

OPERATING INSTRUCTIONS.........................................................................................8

SAFETY PECAUTIONS................................................................................................8

SETUP PROCEDURE ..................................................................................................8

SELECTING ELECTRODE WIRE ..........................................................................8

LOADING ELECTRODE WIRE ..................................................................8 thru 10

DRIVE ROLL GROOVE SELECTION...................................................................11

SETTING GAS FLOW RATE ................................................................................11

TEST WELD SETTINGS.................................................................................11, 12

MAKING A WELD .......................................................................................................12

PROCEDURE SETTINGS ..........................................................................................13

MAINTENANCE..............................................................................................................13

SAFETY PRECAUTIONS ...........................................................................................13

ROUTINE MAINTENANCE ........................................................................................13

TROUBLESHOOTING GUIDE....................................................................................14

DISASSEMBLY AND ASSEMBLY HINTS ..................................................................15

PARTS LIST FOR SPOOL GUN ASSEMBLY NUMBER L8098.....................P198 Series

PART A

PRODUCT DESCRIPTION

The K487 Magnum™ SG spool gun is a lightweight, hand­held combined semiautomatic wire feeder and welding
gun, designed primarily for aluminum welding using argon
shielding gas. The feeding distance of the self-contained
wire supply to the arc is only several inches, eliminating
the wire feeding problems normally associated with feed­ing soft aluminum electrode through a conventional gun
and cable assembly. The cable included with the Magnum
SG allows welding up to 25 feet (7.6 m) from the power
source.

The gun is intended for use with a wide variety of constant
voltage (CV) power sources through the use of the K488
Magnum SG Control Module (see Connection to K488 ...
for CV source requirements). It may also be adapted to the
Lincoln Idealarc

®

SP-150, SP-200 and SP-250 single phase

wire feeder power sources or similar welders (see
Installation to Similar Welders... for requirements).

The Magnum SG is ideal for aluminum fabrication in
industrial shops, automobile body shops, marinas and for
the advanced hobbyist.

SPECIFICATIONS

Model Remote Wire Speed Control

Type K487
Gun Weight (empty) 2.75 pounds (1.25 kg)
Cable Length 25 feet (7.6 m)
Spool Weight, aluminum wire 1 pound (.45 kg)
Spool Size 4 inch (102 mm) diameter
Reversible Wire Drive Roll Narrow groove for .023 to .035"

Wire Speed 50 to 650 ipm (1.3-16.5 m/min)
Current Rating 250 Amps

Welding Current @ 60%

Duty Cycle

(1)

Duty Cycle based on 10 minute time period.

(1)

Magnum SG Spool Gun with

(.6-.9 mm) dia. aluminum wire

Wide groove for 3/64"

(1.2 mm) dia. aluminum wire

RECOMMENDED PROCESSES AND
EQUIPMENT

The spool gun can be used to weld aluminum and alu­minum alloys using Gas Metal Arc Welding or GMAW
(also known as MIG) process, which requires a supply of
shielding gas. Argon is normally used due to its smooth,
stable arc, good metal transfer, and low cost. Positive
polarity gives good penetration and affords a base metal
cathode cleaning effect.

The spool gun should be used with a constant voltage (CV)
type power source, and requires control of wire feed, gas
solenoid valve, and welding power, either external or inter­nal to the power source (see Connection to K488 ... and
Installation to Similar Welders... for specific require­ments).

1

PART B

INSTALLATION

Safety Precautions

— Read “Arc Welding Safety Precautions” in the

Operating Manual before proceeding. Only
personnel that have read and understood the
Operating Manual should install and operate this
equipment.

— Power source must be connected to system ground

per the National Electrical Code and any applicable
local codes.

— Power source must be turned “OFF” and power

leads disconnected when installing this unit.

Unpacking the Spool Gun

Carefully unpack the Magnum K487 Spool Gun, and
make sure you have all of the parts shown below.

SPOOL GUN

.035" (0.9 mm) Contact

Tip Installed

OPERATING MANUAL

Spool Gun Familiarization

Become familiar with your spool gun before
connecting to welder. For features described below,
refer to Figure on the next page.

PACKAGE OF 6 TIPS

For .030, .035, and 3/64"
(0.8, 0.9 and 1.2 mm)
Wire Sizes. 3/64" contact
tip is stamped .045"

CABLE ASSEMBLY

5/64" (2.0 mm)

Allen Wrench

3. Remote wire speed control, located in bottom of
gun handle, controls the speed of the drive motor
when used in conjunction with the Magnum SG
Control Module.

1. Nonslip handle. Gun can be used in either right or
left hand.

2. Trigger operates welding power, gas flow, and wire
feed.

4. Spool gun body has see-through cover so you can
see wire feed through rollers and see which groove
is active on the drive roller. Remove body cover by
unscrewing knob and observe the following:

2

a. Wire drive release lever up position moves

pressure roller away from drive roll to stop wire
feed. Down position moves pressure roller to
wire. Operate wire drive release lever and see
pressure roller move.

b. Drive roll with two wire grooves. Narrow groove

feeds .023 through .035 inch (.6-.9 mm) diameter
wire. Wide groove feeds 3/64 inch (1.2 mm)
diameter wire. Gun is shipped with narrow
groove in operating position (toward handle).
Reverse roller for 3/64 inch (1.2 mm) diameter
wire.

5. Gas nozzle directs gas flow around arc. Gas cone
can be pulled off about 1/4 inch (6 mm) if user
needs more shielding around arc. Pull off gas cone
to see contact tip and gas diffuser. Spool gun is
shipped with .035 inch (.9 mm) contact tip installed.

6. Electrode wire spool cover. Remove by unscrewing
knob. Electrode wire goes into gun through rear
plastic tube. Knurled nut adjusts wire spool braking.

7. Cable assembly for power, control, and gas.

Reassemble gun with spool of wire in spool holder.
Hold gun and become familiar with gun’s weight
and balance.

Spool Gun Installation

The spool gun attaches easily to CV type welders
through the Magnum SG Control Module. The spool
gun also attaches easily to Lincoln models SP-150,
SP-200 and SP-250 power sources and may be adapted
to other similar welders.

Connection to K488 Magnum SG Control Module

1. The K487 Spool Gun connects directly to the
K488 Control Module. With this connection,
the remote wire speed control, in the gun
handle, becomes active. For further details
regarding the connection, consult the K488
Control Module Operating Manual (IM398).

2. The control module allows the spool gun to
be used with any welder possessing the
following characteristics:
a. A constant voltage type welding output.
b. A 115 VAC control circuit output.
c. An output contactor internally or ex-

ternally energized with closure or 115
VAC, respectively.

NOTE: A constant voltage welder without a
contactor may be used, but the electrode wire
will always be electrically “hot”, even when gun
trigger is not activated.

SPOOL GUN FAMILIARIZATION

3

Installation to Lincoln SP-250

The K487 Spool Gun connects directly to the
SP-250 with either a K531-1 or K531-2 Spool
Gun Module Kit. The K531-1 kit is for
SP-250’s with a S19636-1 (or earlier) ROM and
the K531-2 kit is for S19636-2 ROM (or later).
To see which kit you need, turn the SP-250 on
and watch the display. If the display reads
S19636-2 (or higher) you can use the K531-2
kit; if not, you need the K531-1 kit with the new
ROM assembly. For further details regarding
the installation and operation of the Spool Gun
with the SP-250, see the SP-250 Operating
Manual (IM397) or the M16393 Installation and
Operation Sheet provided with the kit.

Installation to Lincoln SP-150

NOTE: Remote wire speed control will not be
functional when K487 Spool Gun is connected
to SP-150. Installation of K487 to SP-150
requires K516 Adapter Assembly.

3. Route end of spool gun control through hole
in front panel and attach to mating connector
of K516 Spool Gun Adapter assembly.

4. Connect red and brown wires of adapter
ssembly to trigger connectors on center
panel. These wires are from the trigger
switch and are interchangeable.

1. Turn off and disconnect electrical power to
welder.

2. Open left side door. Remove trigger wires
from connectors on center panel. If welder is
above Code 9100, remove motor wires from
connectors (marked “Motor”) on center
panel; if welder is below Code 9100, remove
right side cover and remove motor control
wires from motor control circuit board and
pull wires through hole in center panel to left
side of unit. Loosen clamping screw on
connector block and remove gun cable and
control wires through hole in front panel. See
SP-150 Operating Manual (IM340) for details.

5. Connect the black and white motor leads as
follows. Refer to the appropriate illustration
as needed.

5A.Above Code 9100: Connect black and

white wires of adapter assembly to
corresponding terminals on center panel.

5B.Below Code 9100: Connect black and

white extension wires to matching color
wires of adapter assembly and route
through hole in center panel to right side
of welder. Connect white wire to pin 539
and black wire to pin 541 of motor
control circuit board. Reinstall right side
cover.

4

6. Connect spool gun power cable to (+) stud
terminal on SP-150. Disconnect any lead
already attached there.

7. Connect work lead to (–) stud terminal on
SP-150 if not already connected there. Close
left side door.

8. On front control panel of SP-150:
8A. Connect spool gun gas line to gas outlet

9. Connect regulated argon gas supply to gas
inlet fitting on rear panel of SP-150.

fitting.

8B. Set welding voltage.

8C. Set wire feed speed.

(1)

See Part B, “Test Weld Settings".

(1)

(1)

NOTE: Connector pinouts show view of mating connector sides.

SPOOL GUN GUN CABLE ADAPTER CABLE

CONTROL CIRCUIT DIAGRAM (ABOVE CODE 9100) FOR SP-150

NOTE: Connector pinouts show view of mating connector sides.

SPOOL GUN GUN CABLE ADAPTER CABLE & WIRES

CONTROL CIRCUIT DIAGRAM (BELOW CODE 9100) FOR SP-150

5

Installation to Lincoln SP-200

NOTE: Remote wire speed control will not be
functional when K487 Spool Gun is connected
to SP-200. Installation of K487 to SP-200
requires K517 Adapter Assembly.

4. Disconnect any cables attached to (+) stud
terminal on front panel and connect spool
gun power cable to same.

5. Connect work cable to (–) stud terminal,
disconnecting any leads already attached
there.

6. On front control panel of SP-200:
6A. Connect spool gun gas line to gas outlet

fitting. Connect regulated argon gas
supply to gas inlet fitting.

6B.Set coarse and fine welding voltage

controls.

6C. Set wire feed speed.

(1)

(1)

1. Turn off and disconnect electrical power to
welder.

2. Open right side door. If standard gun is
installed, disconnect gas fitting and
Amphenol connector on front panel, loosen
clamping bolt on contact block of wire feed
unit, and remove gun cable assembly.

3. Loosen clamp and disconnect internal control
cable (4-prong connector) from wire feed
chassis. Route spool gun control cable
through hole in front panel and connect to
mating end of K517 Adapter Assembly. Plug
4-prong connector on adapter assembly into
internal control cable. Close door.

(1)

See Part B, “Test Weld Settings”.

NOTE: Connector pinouts show view of mating connector

sides.

CONTROL CIRCUIT DIAGRAM

6

Installation to Similar Welders with Wire Feed

Control

NOTE: Remote wire speed control will not be
functional when K487 Spool Gun is connected
to welders with internal wire feed control
circuitry. K516 Adapter assembly required.

Installation to other welders is possible as long
as the welder meets the following requirements:

1. Must be a constant voltage (CV) type power
source.

2. Must have a low voltage trigger control
circuit (≤ 24 VAC) which operates power
and gas flow.

3. Must have a wire feed motor control circuit
with approximately 5-24 VDC output range.

4. Must have a solenoid-operated gas handling
system capable of supplying argon at flow
rates of 20-40 cubic feet per hour (cf/h) (9-19
1/min) and a 5/8"-18 RH thread gas fitting
for connection to the spool gun.

9. Set wire feed speed and welding voltage
controls.

(1)

(1)

See Part B, “Test Weld Settings”.

NOTE: Connector pinouts show view of mating
side of connectors.

The general procedure to install the spool gun is
as follows:

1. Have a qualified serviceman make the
installation.

2. Make sure power source is turned off and
disconnected from supply.

3. Gain access to wire feed compartment and
disconnect and remove wire feed cable and
gun assembly, if installed.

4. Install spool gun power lead to (+) output
terminal of power source. Connect work lead
to (–) output terminal.

5. Connect spool gun gas line to mating output
connector on power source. Connect
regulated argon gas supply to input connector
on power source.

6. Connect black lead from K516 Adapter
assembly to positive connection of motor
control circuit. Similarly, connect white lead
to negative connection of same. Refer to
control circuit diagram on this page for
connector pinouts.

CONTROL CIRCUIT DIAGRAM

7. Connect brown and red leads (inter­changeable) from adapter assembly to trigger
circuit input connection.

8. Connect spool gun control cable to adapter
assembly.

7

OPERATING INSTRUCTIONS

Safety Precautions

matching. In addition, several wire sizes are
available, and the choice here will depend upon
several factors, including base metal thickness
and the arc transfer process used. Consult your
local dealer or appropriate AWS publication for
help in selecting an appropriate alloy type and
wire size. Also refer to Part B, “Procedure
Settings”, for wire sizes used with typical base
metal thicknesses and procedure settings.

Loading Electrode Wire

1. Pull off gas cone and push idle roller pressure
release lever up.

WARNING: Electric shock can kill. Fumes and gases
can be dangerous to your health. Arc rays can injure
eyes and burn skin. See additional warning
information under “Arc Welding Safety Precautions”
on inside of front cover of operating manual. When
inching, the electrode and drive mechanism are
always electrically energized and remain energized
several seconds after the gun trigger is released.

Setup Procedure

Selecting Electrode Wire

Several alloy types of filler metals are available,
and the best choice depends on the type of base
metals and the desired characteristics of the
weldment, such as ductility and strength,
corrosion resistance, sustained service
temperature, and anodic treatment color

2. Unscrew and remove contact tip.

3. Unscrew spool cover knob and remove spool
cover.

4. Unscrew and remove knurled spool brake
nut.

8

5. Select wire of size and type needed. Wire
must be straight, with no kinks or bends.
Check drive roller for the correct groove
positioning for the size wire selected. See
Part B, “Drive Roll Groove Selection”, for
details.

6. Put wire spool on shaft and route wire into
plastic tube.

9. Screw on spool brake tension nut and adjust
for slight wire spool braking action.

FITTING THE ELECTRODE WIRE

• Replace the spool brake assembly.

Note: The spool brake assembly must bottom

out against the spool hub nut when
installed.The spring in the spool brake
assembly provides the proper tension on the
wire spool.

HAND NUT

7. Push wire until end of wire exits back tube
and enters front tube.

8. Push wire until wire end extends
approximately 6" (150 mm) past end of gas
diffuser. Re-engage idle roll pressure by
pushing release lever down.

BRAKE SPRING

BRASS WASHER

SPOOL BRAKE ADJUSTMENT

The specifications for the 4 inch spool allow a

variation in the width of the spool of up to 1/16

inch (

spring will handle most spool width variations.

The following adjustments can be made if

required.

If the spool brake is not applying enough ten-

sion on the spool:

• Remove the spool brake assembly and the

spool of wire.

• Remove the spool hub nut and the lock

washer.

• Remove shim washer(s) as needed.

• Remove the spool hub bolt and place the

removed shim washers under the bolt

head.

• Reassemble all components except for the

spool cover.

SPOOL WASHER (NYLON)

SNAP RING

+

1/32 inch tolerance). The spool brake

9

SPOOL BRAKE
ASSEMBLY

SPOOL HUB NUT

SHIM WASHERS

SPOOL COVER

SPOOL WASHER

10. Obtain contact tip sized to match wire
selected. Slip contact tip over wire and

screw into diffuser. Tighten securely.

11. Push on gas cone and cut off wire close to
end of contact tip.

FLA T W ASHER

INCREASING BRAKE TENSION ON THE SPOOL

LOCK WASHER

SPOOL HUB BOLT

FITTING THE ELECTRODE WIRE (Cont.)

If the spool brake is applying too much tesion
on the spool :

• Remove the spool brake assembly and the
spool of wire.

• Remove the spool hub nut and the lock
washer.

• Remove the spool hub bolt.

• Remove the lock washer from under the

bolt head.

• Place the removed lock washer under the
spool hub nut.

• Reassemble all components execpt for the
spool cover.

SPOOL COVER

CAUTION: BE CAREFUL WHEN PUSHING ON
GAS CONE. WIRE END COULD PUNCTURE YOUR
HAND.

12. Reinstall spool cover with cover slot over
plastic tube and secure.

SPOOL BRAKE
ASSEMBLY

SPOOL HUB NUT

SHIM WASHERS

FLA T W ASHER

DECREASING BRAKE TENSION ON THE SPOOL

SPOOL WASHER

LOCK WASHER

SPOOL HUB BOLT

10

Drive Roll Groove Selection

The drive roll has two grooves, a wider and a
narrower one, to accommodate changes in wire
size used. Changing between the grooves simply
requires reversing the drive roll. The following
information is to be used to determine proper
groove positioning and to change it, if
necessary, for the wire size selected.

A. Drive Roll Orientation

4. Slide drive roll off motor shaft. Turn roller

over, end for end.

5. Slide drive roll back on motor shaft and

tighten set screw. Make sure set screw is
on flat part of motor shaft.

6. Remove Allen wrench and reinstall see-

through cover.

Oriented for .023-.035"
(0.6-0.9 mm) electrode
wire with smaller groove
in feed position.

B. Changing Drive Roll Orientation

1. Move release lever to up position and
remove see-through body cover.

2. Rotate drive roll by jogging drive motor
with trigger switch and/or rotating with
fingertips until set screw lines up with slot
in body.

3. Insert 5/64" Allen wrench in set screw and
turn set screw just enough to loosen roller.

Oriented for 3/64" (.045)
(1.2 mm) electrode wire
with larger groove in
feed position.

Setting Gas Flow Rate

Gas handling systems having adjustable flow valves
should be set for the following argon flow rates,
depending on base metal thickness and welding
position.

ARGON SHIELDING GAS FLOW RATES

Material Flow

Thickness Rates

in inches Welding Position in cf/hr
and (mm) (l/min)

1/16 (1.6 mm) Flat 25 cf/hr

(11.8 l/min)

3/32 to 3/16 Flat, Vertical, Horizontal, 30
(2.4 to 4.8 mm) Overhead (14)

Flat 30 (14)
1/4 to 3/8 Vertical, Horizontal 35 (16.5)
(6.3 to 9.5 mm) Overhead 40 (18.9)

Flat 35 (16.5)
3/4 (19 mm) Vertical, Horizontal, 40 (18.9)

Overhead

11

Test Weld Settings

For test weld procedures with other power
sources, refer to Part B, Section 2.4, “Procedure
Settings”, or use the following approximate
settings:

Welding Voltage 22-23V
Wire Feed Speed 250-350 ipm

(6.3 - 8.9 m/min)

The procedure settings below can be used to
make a test weld when the spool gun is used
with a Lincoln model SP-150, SP-200 or
SP-250 power source:

SP-150 SP-200 SP-250

Wire
Wire
Size
in. (mm)

.030 (.8 mm) 325 6.5 375 18-23 2.5 42% 15
.035 (.9mm) 300 7.0 350 18-23 2.5 39% 16
3/64 (1.2 mm) 225 7.5 250 18-23 2.5 32% 21

(1)

Dial not calibrated when used with spool gun.

Speed

Dial

(1)

Voltage
Setting

Arc

Wire

Speed

Dial

Setting

Arc Wire Arc

Voltage Speed Voltage

(1)

Coarse Fine Percentage SettingSetting

Making A Weld

1. Check that the spool gun power, control, and gas
connections are correct for the power source being
used. Check that the gas supply is turned on. Check
wire spool for an adequate supply of wire.

2. See Part B, “Test Weld Setting”, or “Procedure
Settings”, for wire feed speed and voltage settings.
Set these controls depending on the welding wire
and base metal thickness being used.

3. Connect work clamp to metal being welded. Work
clamp must make good electrical contact to the
workpiece. The workpiece must also be grounded as
stated in “Arc Welding Safety Precautions”.

4. Connect power to welder and turn “ON”.

5. Prepare to purge gas line by first releasing wire
drive. Push wire drive release lever to the UP
position.

WARNING: Gun body and contact tip become
electrically energized when gun trigger is pressed and
remain so for several seconds after trigger is released.

Unlock wire feed release

7. Re-engage wire drive by pushing release lever to
down position.

8. Momentarily squeeze trigger and verify that wire
feeds properly. Trim wire to approximately 1/4" (6
mm) from end of contact tip.

WARNING: When using an open arc process, it is
necessary to use correct eye, ear, head, and body
protection.

9. Position gun over joint at 10° pushing angle. End of
wire may be lightly touching the work.

10. Lower welding helmet, close gun trigger, and begin
welding. Hold the gun so that the contact tip to
work distance is about 1/2 inch (13 mm).

11. To stop welding, release the gun trigger and then
pull the gun away from the work after the arc goes
out.

12. When no more welding is to be done, close valve on
gas cylinder, momentarily operate trigger to release
gas pressure in line and turn off power source.

6. Press and hold gun trigger for about 5 seconds to
purge gas line. If adjustable regulator or metering
valve is installed, adjust gas flow per Part B,
“Setting Gas Flow Rate”.

Release wire feed and purge gas line.

13. Note that clogged tips can often be salvaged by
peeling away melted wire.

Weld angle
and distance

Salvaging
clogged tips

12

Procedure Settings

The following procedure settings for aluminum wire and argon gas can be used as starting points for developing
specific welding procedures:

Wire Metal Wire Amps

Size Thickness Speed DC

in. (mm) ga. in. (mm) Arc Volts ipm (mpm) (+)

.030 (0.8) 22 .030 (0.8) 13-14

.035 (0.9) 22 .030 (0.8) 13-14

3/64 (1.2) 10 .135 (3.5) 20-21

(1)

Short arc transfer.

MAINTENANCE

Safety Precautions

20 .036 (1.0) 13-14
18 .048 (1.2) 14-15
16 .060 (1.6) 15-16
14 .075 (2.0) 16-17
12 .105 (2.5) 16-18

(1)
(1)
(1)
(1)
(1)
(1)

200 (5.1) 40
240 (6.1) 40
290 (7.4) 50
340 (8.6) 60
370 (9.4) 70
430 (10.9) 90

10 .135 (3.5) 24-26 460 (11.7) 110

3/16 (5.0) 24-26 500 (12.7) 150

1/4 (6.0) 28-29 560 (14.2) 180
3/8 (10.0) 28-30 600 (15.2) 200

20 .036 (1.0) 13-14
18 .048 (1.2) 13-14
16 .060 (1.6) 14-16
14 .075 (2.0) 14-16
12 .105 (2.5) 16-18

(1)
(1)
(1)
(1)
(1)
(1)

150 (3.8) 40
175 (4.4) 40
215 (5.5) 50
250 (6.4) 60
270 (6.9) 70
320 (8.1) 90

10 .135 (3.5) 24-26 410 (10.4) 110

3/16 (5.0) 24-26 450 (11.4) 150

1/4 (6.0) 26-28 530 (13.5) 180
3/8 (10.0) 26-29 560 (14.2) 200
1/2 (12.0) 26-30 600 (15.2) 220

3/16 (5.0) 20-21

(1)
(1)

180 (4.6) 110

220 (5.6) 150
1/4 (6.0) 27-28 250 (6.4) 180
3/8 (10.0) 25-30 260 (6.6) 200
1/2 (12.0) 25-31 270 (6.9) 220
3/4 (20.0) 25-31 290 (7.4) 250

make wire drive rollers slip. Be careful when using
any of these liquids on spool gun.

After 500 hours operation or 24 months time,
whichever comes first, oil motor with light lubricating
oil. Apply oil to pressure roller bearing on the end of a
toothpick so oil will not contaminate drive surface of
wire drive rollers.

When finished welding, be sure to turn power source
off and close valve on gas cylinder.

Routine Maintenance

NOTE: Oil and spray cleaners can contaminate

electrode wire and cause bad welds. They could also

Carefully clean gun with a cleaner that is safe for
plastic. Apply cleaner to rag and wipe gun. Do NOT
spray cleaner on gun. Keep cable clean. Oil, grease
gasoline, paint, and solvents degrade cable insulation.

13

Troubleshooting Guide

PROBLEM

No arc, wire feed, or gas flow.

No arc, weak arc.

No wire feed.

SYMPTOMS

1. Cable connections loose.

2. Trigger switch loose or defective.

3. Welder not turned on.

4. Welder not plugged in.

5. Cable or adapter cable damaged.

6. Adapter (if used) not connected.

1. Poor ground connection to work.

2. Power cable connection loose.

3. Voltage set too low.

4. Tip too large for wire size.

1. Feeding small diameter wire with
large groove on drive roller.

2. Wire drive release open.

3. Wire welded to tip.

4. Wire spool empty.

5. Tip too small for wire.

6. Kink or bend in wire.

7. Spool tension too tight.

8. Spool cover binding.

9. Control cable loose.

10. Drive roller worn.

11. Pressure roller stuck.

12. Roller spring loose or broken.

REMEDY

1. Check all power connections.

2. Fix switch or replace.

3. Turn on welder power.

4. Plug in.

5. Inspect and replace.

6. Connect adapter.

1. Check ground connection.

2. Check connections; if defective, replace
cable or connectors.

3. Adjust to proper voltage.

4. Change tip size.

1. Change position of wire drive roller.

2. Close wire drive release.

3. Peel wire off tip or use new tip.

4. Insert new spool.

5. Insert correct tip.

6. Pull wire through tip or start new wire
end.

7. Loosen spool tension nut.

8. Rotate spool cover slot to proper position.

9. Check all connections.

10. Replace.

11. Replace or lubricate.

12. Replace.

Wire feed too fast or too slow.

Wire feed rollers go backward.

Low or no gas flow. Oxidation
of work.

Oxidized work, arc unstable.

Gas cone wobbles.

Contact tip extension.

1. Wrong wire speed set for work.

1. Electrical connections reversed in
adapter cable (or wires).

1. Gas flow not set right.

2. Cylinder out of gas.

3. Cylinder valve closed.

4. Leak in gas line.

5. Leak in gun.

1. Wrong welding polarity.

1. Insulator loose.

1. Gas cone positioned incorrectly.

1. Adjust wire feed speed at welder’s con­trol panel, or at remote wire speed control
in spool gun handle (where applicable).

1. Check all gun (and adapter) cable connec­tions.

1. Set proper flow rate.

2. Get new cylinder of gas.

3. Open cylinder valve.

4. Inspect and replace.

5. Check for missing gun tubes and/or miss­ing gun body cover.

1. Check polarity.

1. Tighten insulator, but not enough to dam­age threads.

1. Slide gas cone in or out to position need­ed for work.

14

DISASSEMBLY AND ASSEMBLY HINTS

Numbers in parentheses refer to Parts List page num­ber and Item Number.

When applying torque on nozzle parts (P198-D,#1
through #8), hold gun by molded base (P198-D,#27)
or body block (P198-D#43), not by handle (P198­D,#13) or motor(P198-D,#42).

When assembling handle to molded base, make sure
switch wires (P198-D,#19) are not pinched between
handle and motor. Pinched wires could cause welding
voltage to short to control circuit.

To remove gas power connector (P198-F,#72) from
gun body, remove handle so bottom plate can move
away from body.

To install woven insulating sheath (P198-D,#6), put
one end halfway into steel sleeve (P198-D,#5) and put
other end over barrel(P198-D,#8). Then push both
sleeves over barrel together.

When replacing brass barrel, first put antiseizing com­pound on threads that go into aluminum body.

When reinstalling Telflon lin (P198-D,#9), put O-ring
(P198-D,#10) over narrow part of tubing.

Gas passage seal, set screw(P198-D,#24) [front], is
sealed with Teflon tape.

15

WARNING

Spanish

AVISO DE

PRECAUCION

● Do not touch electrically live parts or

electrode with skin or wet clothing.

● Insulate yourself from work and

ground.

● No toque las partes o los electrodos

bajo carga con la piel o ropa moja­da.

● Aislese del trabajo y de la tierra.

● Keep flammable materials away.

● Mantenga el material combustible

fuera del área de trabajo.

● Wear eye, ear and body protection.

● Protéjase los ojos, los oídos y el

cuerpo.

French

ATTENTION

German

WARNUNG

Portuguese

ATENÇÃO

Japanese

Chinese

Korean

Arabic

● Ne laissez ni la peau ni des vête-

ments mouillés entrer en contact
avec des pièces sous tension.

● Isolez-vous du travail et de la terre.

● Berühren Sie keine stromführenden

Teile oder Elektroden mit Ihrem
Körper oder feuchter Kleidung!

● Isolieren Sie sich von den

Elektroden und dem Erdboden!

● Não toque partes elétricas e elec-

trodos com a pele ou roupa molha­da.

● Isole-se da peça e terra.

● Gardez à l’écart de tout matériel

inflammable.

● Entfernen Sie brennbarres Material!

● Mantenha inflamáveis bem guarda-

dos.

● Protégez vos yeux, vos oreilles et

votre corps.

● Tragen Sie Augen-, Ohren- und Kör-

perschutz!

● Use proteção para a vista, ouvido e

corpo.

READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE
USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.

SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS
CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.

LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A
ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.

LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HER­STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.

● Keep your head out of fumes.

● Use ventilation or exhaust to

remove fumes from breathing zone.

● Turn power off before servicing.

● Do not operate with panel open or

guards off.

WARNING

● Los humos fuera de la zona de res-

piración.

● Mantenga la cabeza fuera de los

humos. Utilice ventilación o
aspiración para gases.

● Gardez la tête à l’écart des fumées.

● Utilisez un ventilateur ou un aspira-

teur pour ôter les fumées des zones
de travail.

● Vermeiden Sie das Einatmen von

Schweibrauch!

● Sorgen Sie für gute Be- und

Entlüftung des Arbeitsplatzes!

● Mantenha seu rosto da fumaça.

● Use ventilação e exhaustão para

remover fumo da zona respiratória.

● Desconectar el cable de ali-

mentación de poder de la máquina
antes de iniciar cualquier servicio.

● Débranchez le courant avant l’entre-

tien.

● Strom vor Wartungsarbeiten

abschalten! (Netzstrom völlig öff­nen; Maschine anhalten!)

● Não opere com as tampas removidas.

● Desligue a corrente antes de fazer

serviço.

● Não toque as partes elétricas nuas.

● No operar con panel abierto o

guardas quitadas.

● N’opérez pas avec les panneaux

ouverts ou avec les dispositifs de
protection enlevés.

● Anlage nie ohne Schutzgehäuse

oder Innenschutzverkleidung in
Betrieb setzen!

● Mantenha-se afastado das partes

moventes.

● Não opere com os paineis abertos

ou guardas removidas.

Spanish

AVISO DE

PRECAUCION

French

ATTENTION

German

WARNUNG

Portuguese

ATENÇÃO

Japanese

Chinese

Korean

Arabic

LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS
PRÁTICAS DE SEGURANÇA DO EMPREGADOR.

• World's Leader in Welding and Cutting Products •

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: [phone] FAX: [phone] WEB SITE: www.lincolnelectric.com