Lincoln Electric IM10059 User Manual

IM10059

RETURN TO MAIN MENU

SQUARE WAVE™TIG 175

For use with machines having Code Numbers:

Safety Depends on You

Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thoughtful
operation on your part. DO NOT

INSTALL, OPERATE OR REPAIR
THIS EQUIPMENT WITHOUT
READING THIS MANUAL AND
THE SAFETY PRECAUTIONS
CONTAINED THROUGHOUT.

And, most importantly, think before
you act and be careful.

March, 2010

11691

Cleveland, Ohio 44117-1199 U.S.A. TEL: [phone] FAX: [phone] WEB SITE: www.lincolnelectric.com

OPERATOR’S MANUAL

Copyright © Lincoln Global Inc.

• World's Leader in Welding and Cutting Products •

• Sales and Service through Subsidiaries and Distributors Worldwide •

i

SAFETY

WARNING

CALIFORNIA PROPOSITION 65 WARNINGS

For Diesel Engines: Diesel engine exhaust and
some of its constituents are known to the State
of California to cause cancer, birth defects, and
other reproductive harm.

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.
KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you
purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society,P.O. Box 351040,
Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the
Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

For Gasoline Engines: The engine exhaust from
this product contains chemicals known to the
State of California to cause cancer, birth defects,
or other reproductive harm.

i

FOR ENGINE
powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance
work unless the maintenance work requires it to be running.

____________________________________________________

1.b.Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes
outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame weld-

ing arc or when the engine is running. Stop
the engine and allow it to cool before refuel­ing to prevent spilled fuel from vaporizing on
contact with hot engine parts and igniting. Do
not spill fuel when filling tank. If fuel is spilled,
wipe it up and do not start engine until fumes
have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards,coversand devices in posi­tion and in good repair.Keep hands, hair, clothing and tools
away from V-belts, gears, fans and all other moving parts
when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove
guards only when necessary and replace them when the
maintenance requiring their removal is complete.
Always use the greatest care when working near moving
parts.

___________________________________________________

1.f. Do not put your hands near the engine fan.
Do not attempt to override the governor or
idler by pushing on the throttle control rods
while the engine is running.

1.h. To avoid scalding, do not remove the
radiator pressure cap when the engine is
hot.

ELECTRIC AND
MAGNETIC FIELDS
may be dangerous

2.a. Electric current flowing through any conductor causes
localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and
welding machines

2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.

2.c. Exposure to EMF fields in welding may have other health
effects which are now not known.

2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:

2.d.1.

Route the electrode and work cables together - Secure
them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and

work cables. If the electrode cable is on your right
side, the work cable should also be on your right side.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenance
work, disconnect the spark plug wires, distributor cap or
magneto wire as appropriate.

2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.

2.d.5. Do not work next to welding power source.

Mar ‘95

ii

SAFETY

ii

ELECTRIC SHOCK can kill.

3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.

In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.

3.f.

Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.

3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

ARC RAYS can burn.

4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.

FUMES AND GASES
can be dangerous.

5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases. When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. When

welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and within applicable OSHA PEL and
ACGIH TLV limits using local exhaust or mechanical ven­tilation. In confined spaces or in some circumstances,
outdoors, a respirator may be required. Additional pre­cautions are also required when welding on galvanized
steel.

5. b. The operation of welding fume control equipment is affected
by various factors including proper use and positioning of the
equipment, maintenance of the equipment and the specific
welding procedure and application involved. Worker expo­sure level should be checked upon installation and periodi­cally thereafter to be certain it is within applicable OSHA PEL
and ACGIH TLV limits.

5.c.

Do not weld in locations near chlorinated hydrocarbon
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors
form phosgene, a highly toxic gas, and other irritating prod­ucts.

vapors

to

5.d. Shielding gases used for arc welding can displace air and

cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.

5.f. Also see item 1.b.

Jan ‘09

iii

SAFETY

iii

WELDING and CUTTING
SPARKS can
cause fire or explosion.

6.a.

Remove fire hazards from the welding area.

If this is not possible, cover them to prevent

Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.

6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact can
cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even
been “cleaned”. For information, purchase “Recommended
Safe Practices for the
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.

Sparks and spatter are thrown from the welding arc. Wear oil

6.f.
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.

6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate circuits.
This can create fire hazards or overheat lifting chains or
cables until they fail.

6.h. Also see item 1.c.

the welding sparks from starting a fire.

though

they have

Preparation

for Welding and Cutting of

CYLINDER may explode
if damaged.

7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
process used and properly operating
regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from arc welding or cutting operations and

any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.

7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY
powered equipment.

8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.

8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.

8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.

6.I. Read and follow NFPA 51B “ Standard for Fire Prevention
During Welding, Cutting and Other Hot Work”, available from
NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma
022690-9101.

6.j. Do not use a welding power source for pipe thawing.

Refer to http://www.lincolnelectric.com/safety for additional safety information.

Jan ‘09

iv

SAFETY

iv

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv­antes:

Sûreté Pour Soudage A L’Arc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand on

soude dans desendroitshumides, ou sur un plancher met­allique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.

c. Maintenir leporte-électrode,la pince de masse, lecâblede

soudage et la machine à souder en bon et sûr état defonc­tionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à soud­er parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.

zones où l’on pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.

8. S’assurer que la masseestconnectée le plus prés possible de
la zone de travail qu’il est pratique de le faire. Si on place la
masse sur la charpentedelaconstruction ou d’autres endroits
éloignés de la zone de travail, on augmente le risque de voir
passer le courant de soudage par les chaines de levage,
câbles de grue, ou autres circuits. Cela peut provoquer des
risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.

11.Pour obtenir de plus amples renseignements sur la sûreté, voir
le code “Code for safety in welding and cutting” CSAStandard
W 117.2-1974.

2. Dans le cas de travail au dessus du niveau dusol,seprotéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi qu’un verre blanc afin de se protégerlesyeuxduray­onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de
l‘arc.

c. Protéger l’autre personnel travaillant à proximité au

soudage à l’aide d’écrans appropriésetnon-inflammables.

4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec desvêtementsdeprotection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan­talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les

PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR

1. Relier à la terrelechassisduposteconformementau code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la debranch­er à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur
place.

Mar. ‘93

Thank You

vv

for selecting a QUALITY product by Lincoln Electric. We want you
to take pride in operating this Lincoln Electric Company product •••
as much pride as we have in bringing this product to you!

The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip­ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric
for advice or information about their use of our products. We respond to our customers based on the best information in our possession at that
time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such information or
advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose, with respect
to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or correcting any
such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any warranty with
respect to the sale of our products.

Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control
of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in apply­ing these types of fabrication methods and service requirements.

Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com
for any updated information.

CUSTOMER ASSISTANCE POLICY

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the time
the shipment is received.

Please record your equipment identification information below for future reference. This information can be found
on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

“Product Registration”. Please complete the form and submit your registration.

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:

WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.

CAUTION

This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.

TABLE OF CONTENTS

Page

_______________________________________________________________________________________

Installation ......................................................................................................Section A

Technical Specifications...............................................................................................A-1

Safety Precautions

Select Suitable Location........................................................................................A-2

Grinding.................................................................................................................A-2

Stacking.................................................................................................................A-2

Lifting.....................................................................................................................A-2

Tilting.....................................................................................................................A-2

Environmental Rating............................................................................................A-2

Machine Grounding and High F

Input Connections........................................................................................................A-3

Input Reconnect Procedure.........................................................................................A-3

Output Connections.....................................................................................................A-4

Connections For Tig (GTAW) Welding............................................................A-4

Tig Torch Connections ....................................................................................A-4

Work Cable Connections................................................................................A-4

Shielding Gas Connection ..............................................................................A-4

Remote Control Connection............................................................................A-5

Connections For Stick (SMAW) Welding .......................................................A-5

Stick Electrode Cable and Work Cable Connection.......................................A-5

______________________________________________________________________________

PERATION.........................................................................................................................................................Section B-1

O

Safety Precautions.......................................................................................................B-1

Product Description......................................................................................................B-1

Included Equipment...............................................................................................B-1

GTAW (Tig Welding): ......................................................................................B-1

SMAW (Stick Welding):...................................................................................B-1

Installation and Startup:..................................................................................B-1

Welding Capability.................................................................................................B-1

Controls and Settings ..........................................................................B-2 THRU B-3

Operating Steps.....................................................................................................B-3

Welding in Tig Mode .......................................................................................B-3

Remote Control Operation..............................................................................B-3

Benefits of the SQUARE WAVE™ Operation.................................................B-3

Welding in Stick Mode ..........................................................................................B-4

______________________________________________________________________________

Accessories

............................................................................................................................................... .......Section C

Optional Equipment .....................................................................................................C-1

______________________________________________________________________________

Maintenance

......................................................................................................................................................Section D

Safety Precautions.......................................................................................................D-1

Routine and Periodic Maintenance..............................................................................D-1

______________________________________________________________________________

Troubleshooting

Safety Precautions.......................................................................................................E-1

How To Use troubleshooting Guide .............................................................................E-1

Troubleshooting.................................................................................................E-2 to E-7

______________________________________________________________________________

Diagrams

..............................................................................................................................................................Section F

Wiring Diagram 208/230 V Model...................................................................................................................F-1

______________________________________________________________________________

Parts List

......................................................................................................................................................................P-650

.. ............................................................................................................................................... .A-2

REQUENCY INTERFERENCE PROTECTION ...................A-2,A-3

.............................................................................................................................................Section E

vivi

A-1

INSTALLATION

TECHNICAL SPECIFICATIONS - SQUARE WAVE™ TIG 175 (K1478-5)

INPUT - SINGLE PHASE ONLY

Standard

Voltage

208/230/1/60

Duty Cycle

GTAW 25% Duty Cycle

40% Duty Cycle
60% Duty Cycle

100% Duty Cycle

Input Current at

Rated Output

58/52 AC/DC Stick & DC TIG - 64/57 AC TIG

RATED OUTPUT

Amps

150
125
110

90

Volts at Rated Amperes

Code

Number

11691

15.0 V AC/DC

14.7 V AC/DC

14.3 V AC/DC

14.1V AC/DC

A-1

SMAW 25% Duty Cycle

40% Duty Cycle
60% Duty Cycle

100% Duty Cycle

150
125
110

90

26.0 V AC/DC

25.0 V AC/DC

25.0 V AC/DC

24.0 V AC/DC

OUTPUT

Maximum Open

Output Current

Range

10-175 Amps

AC and DC

Circuit Voltage

(STICK AND TIG)

AC OCV: 74
DC OCV: 59

Type of Output

CC (Constant Current)

AC/DC

RECOMMENDED FUSE SIZES

Wiring and Protection based on the 2008 National Electric Code.

Use a Super Lag type Fuse or Circuit Breaker with a delay in tripping action. Models with NEMA 6-50P plug
may be used with a 50 amp protected 6-50R receptacle, or with a maximum 70 amp protected 6-50R receptacle
if dedicated for the welder.

PHYSICAL DIMENSIONS

Height Width Depth Weight

Power 19.53 in. 13.72 in. 24.94 in. Approx. 200 lbs.
Source

496 mm 349 mm 633 mm 90.9 kgs.

SQUARE WAVE™ TIG 175

A-2

INSTALLATION

A-2

SAFETY PRECAUTIONS

Read entire installation section before starting
installation.

WARNING

ELECTRIC SHOCK can kill.

• Only qualified personnel should

perform this installation.

• Turn the input power OFF at the
disconnect switch or fuse box
before working on this
equipment.

• Do not touch electrically hot
parts.

• Always connect the SQUARE WAVE™ TIG 175 to a
power supply grounded per the National Electrical
Code and any local codes.

SELECT SUITABLE LOCATION

Place the welder where clean cooling air can freely cir­culate in through the rear louvers and out through the
front and side louvers. Dirt, dust or any foreign mater­ial that can be drawn into the welder should be kept at
a minimum. Failure to observe these precautions can
result in excessive operating temperatures and nui­sance shut-downs.

GRINDING

Do not direct grinding particles towards the welder.An
abundance of conductive material can cause mainte­nance problems.

MACHINE GROUNDING AND HIGH FRE­QUENCY INTERFERENCE PROTECTION

The welder must be grounded. See your local and national
electricalcodes forpropergroundingmethods.

The high frequency generator, being similar to a radio
transmitter, can be blamed for radio, TV and electronic
equipment interference problems. These problems
may be the result of radiated interference. Proper
grounding methods can reduce or eliminate radiated
interference.

Radiated interference can develop in the following four
ways:

1. Direct interference radiated from the welder.

2. Direct interference radiated from the welding leads.

3. Direct interference radiated from feedback into the
power lines.

4. Interference from re-radiation of “pickup” by
ungrounded metallic objects.

Keeping these contributing factors in mind, installing
equipment per the following instructions should mini­mize problems.

STACKING

SQUARE WAVE™ TIG 175’s cannot

be stacked.

LIFTING AND MOVING

The SQUARE WAVE™ TIG 175 should be lifted by two

or more people or with a hoist. (It weighs approximate-

ly 200 lbs./90.9 kg.) Its lifting handles are designed to

make lifting more convenient.An optional undercarriage
isavailable

to easily move

the unit. Refer to the

Accessories section of this manual.

TILTING

Each machine must be placed on a secure, level sur­face, either directly or on a recommended undercar­riage. The machine may topple over if this procedure
is not followed.

ENVIRONMENTAL RATING

The SQUARE WAVE™ TIG 175 power source carries an
IP21 environmental rating. It may be used in normal indoor
industrial and commercial environments. Avoid using it in
environments which have falling water such as rain. Read
and follow “Electric Shock Warnings” in the Safety section if
welding must be performed under electrically hazardous
conditions such as welding in wet areas or on or in the work­piece.

1. Keep the welder power supply lines as short as pos­sible and enclose as much of them as possible in
rigid metallic conduit or equivalent shielding for a
distance of 50 feet (15.2m). There should be good
electrical contact between this conduit and the
welder case ground. Both ends of the conduit
should be connected to a driven ground and the
entire length should be continuous.

2. Keep the work and electrode leads as short as pos­sible and as close together as possible. Lengths
should not exceed 25 ft (7.6m). Tape the leads
together when practical.

3. Be sure the torch and work cable rubber coverings
are free of cuts and cracks that allow high frequen­cy leakage.

4. Keep the torch in good repair and all connections
tight to reduce high frequency leakage.

5. The work piece must be connected to an earth
ground close to the work clamp, using one of the
following methods:

SQUARE WAVE™ TIG 175