Lincoln Electric C300 CE User Manual

Download

Page 1

IM10038

RETURN TO MAIN MENU

POWER WAVE

For use with machines having Code Numbers:

Safety Depends on You

Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thoughtful operation on your part. DO NOT INSTALL,

OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS CONTAINED THROUGHOUT.

And, most importantly, think before you act and be careful.

11624

C300 CE

August, 2010

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

IEC 60974-1

N80

OPERATOR’S MANUAL

• World's Leader in Welding and Cutting Products •

• Sales and Service through Subsidiaries and Distributors Worldwide •

Page 2

SAFETY

WARNING

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.

The Above For Diesel Engines

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

The Above For Gasoline Engines

FOR ENGINE powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame welding arc or when the engine is running. Stop the engine and allow it to cool before refueling to prevent spilled fuel from vaporizing on contact with hot engine parts and igniting. Do not spill fuel when filling tank. If fuel is spilled, wipe it up and do not start engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in position and in good repair.Keep hands, hair, clothing and tools away from V-belts, gears, fans and all other moving parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove guards only when necessary and replace them when the maintenance requiring their removal is complete. Always use the greatest care when working near moving parts.

___________________________________________________

1.f. Do not put your hands near the engine fan. Do not attempt to override the governor or idler by pushing on the throttle control rods while the engine is running.

1.h. To avoid scalding, do not remove the radiator pressure cap when the engine is hot.

ELECTRIC AND MAGNETIC FIELDS may be dangerous

2.a. Electric current flowing through any conductor causes localized Electric and Magnetic Fields (EMF). Welding current creates EMF fields around welding cables and welding machines

2.b. EMF fi elds m ay interf ere wi th some pacemak ers, a nd welders having a pacemaker should consult their physician before welding.

2.c. Exposure to EMF fields in welding may have other health effects which are now not known.

2.d. All welders should use the following procedures in order to minimize exposure to EMF fields from the welding circuit:

2.d.1.

Route the electrode and work cables together - Secure them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and

work cables. If the electrode cable is on your right side, the work cable should also be on your right side.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while turning the engine or welding generator during maintenance work, disconnect the spark plug wires, distributor cap or magneto wire as appropriate.

2.d.4. Connect the work cable to the workpiece as close as possible to the area being welded.

2.d.5. Do not work next to welding power source.

Page 3

SAFETY

ELECTRIC SHOCK can kill.

3.a. The electrode and work (or ground) circuits are electrically “hot” when the welder is on. Do not touch these “hot” parts with your bare skin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation. Make certain the insulation is large enough to cover your full area of physical contact with work and ground.

In addition to the normal safety precautions, if welding must be performed under electrically hazardous conditions (in damp locations or while wearing wet clothing; on metal structures such as floors, gratings or scaffolds; when in cramped positions such as sitting, kneeling or lying, if there is a high risk of unavoidable or accidental contact with the workpiece or ground) use the following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode, electrode reel, welding head, nozzle or semiautomatic welding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical connection with the metal being welded. The connection should be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical (earth) ground.

3.f.

Maintain the electrode holder, work clamp, welding cable and welding machine in good, safe operating condition. Replace damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of electrode holders connected to two welders because voltage between the two can be the total of the open circuit voltage of both welders.

3.i. When working above floor level, use a safety belt to protect yourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

ARC RAYS can burn.

4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant material to protect your skin and that of your helpers from the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable screening and/or warn them not to watch the arc nor expose themselves to the arc rays or to hot spatter or metal.

FUMES AND GASES can be dangerous.

5.a. Welding ma y produce fumes and gases hazardous to health. Avoid breathing these fumes and gases. When welding, keep your head out of the fume. Use enough ventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. When

welding with electrodes which require special ventilation such as stainless or hard facing (see instructions on container or MSDS) or on lead or cadmium plated steel and other metals or coatings which produce highly toxic fumes, keep exposure as low as possible and within applicable OSHA PEL and ACGIH TLV limits using local exhaust or mechanical ventilation. In confined spaces or in some circumstances, outdoors, a respirator may be required. Additional precautions are also required when welding on galvanized steel.

5. b. The operation of welding fume control equipment is affected by various factors including proper use and positioning of the equipment, maintenance of the equipment and the specific welding procedure and application involved. Worker exposure level should be checked upon installation and periodically thereafter to be certain it is within applicable OSHA PEL and ACGIH TLV limits.

5.c.

Do not weld in locations near chlorinated hydrocarbon coming from degreasing, cleaning or spraying operations. The heat and rays of the arc can react with solvent vapors form phosgene, a highly toxic gas, and other irritating products.

5.d. Shielding gases used for arc welding can displace air and

cause injury or death. Always use enough ventilation, especially in confined areas, to insure breathing air is safe.

vapors

5.e. Read and understand the manufacturerʼs instructions for this

equipment and the consumables to be used, including the material safety data sheet (MSDS) and follow your employerʼs safety practices. MSDS forms are available from your welding distributor or from the manufacturer.

5.f. Also see item 1.b.

Page 4

iii

SAFETY

iii

WELDING and CUTTING SPARKS can cause fire or explosion.

6.a.

Remove fire hazards from the welding area.

If this is not possible, cover them to prevent

Remember that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas. Avoid welding near hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special precautions should be used to prevent hazardous situations. Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1) and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is touching the work or ground. Accidental contact can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the proper steps have been taken to insure that such procedures will not cause flammable or toxic vapors from substances inside. They can cause an explosion even been “cleaned”. For information, purchase “Recommended Safe Practices for the Containers and Piping That Have Held Hazardous Substances”, AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or welding. They may explode.

Sparks and spatter are thrown from the welding arc. Wear oil

6.f. free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes and a cap over your hair. Wear ear plugs when welding out of position or in confined places. Always wear safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area as practical. Work cables connected to the building framework or other locations away from the welding area increase the possibility of the welding current passing through lifting chains, crane cables or other alternate circuits. This can create fire hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

the welding sparks from starting a fire.

though

they have

Preparation

for Welding and Cutting of

CYLINDER may explode if damaged.

7.a. Use on ly com pr essed gas cylinders containing the correct shielding gas for the process used and properly operating regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for the application and maintained in good condition.

7.b. Alway s keep cylinders in an upright position securely chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from arc welding or cutting operations and

any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight except when the cylinder is in use or connected for use.

7.g. Re ad and foll ow the inst ru ctions o n c ompressed ga s cylinders, associated equipment, and CGA publication P-l, “Precautions for Safe Handling of Compressed Gases in Cylinders,” available from the Compressed Gas Association 1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY powered equipment.

8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment.

8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturerʼs recommendations.

8.c. Ground the equipment in accordance with the U.S. National Electrical Code and the manufacturerʼs recommendations.

6.I. Read and follow NFPA 51B “ Standard for Fire Prevention During Welding, Cutting and Other Hot Work”, available from NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma 022690-9101.

6.j. Do not use a welding power source for pipe thawing.

Refer to http://www.lincolnelectric.com/safety for additional safety information.

Page 5

SAFETY

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suivantes:

Sûreté Pour Soudage A LʼArc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à lʼélectrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours tout contact entre les parties sous tension et la peau nue ou les vétements mouillés. Porter des gants secs et sans trous pour isoler les mains.

b. Faire trés attention de bien sʼisoler de la masse quand on

soude dans des endroits humides, ou sur un plancher metallique ou des grilles metalliques, principalement dans les positions assis ou couché pour lesquelles une grande partie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état defonctionnement.

d.Ne jamais plonger le porte-électrode dans lʼeau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à souder parce que la tension entre les deux pinces peut être le total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions pour le porte-électrode sʼapplicuent aussi au pistolet de soudage.

2. Dans le cas de travail au dessus du niveau du sol, se protéger contre les chutes dans le cas ou on recoit un choc. Ne jamais enrouler le câble-électrode autour de nʼimporte quelle partie du corps.

5. Toujours porter des lunettes de sécurité dans la zone de soudage. Utiliser des lunettes avec écrans lateraux dans les zones où lʼon pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de prévenir tout risque dʼincendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de la masse. Un court-circuit accidental peut provoquer un échauffement et un risque dʼincendie.

8. Sʼassurer que la masse est connectée le plus prés possible de la zone de travail quʼil est pratique de le faire. Si on place la masse sur la charpente de la construction ou dʼautres endroits éloignés de la zone de travail, on augmente le risque de voir passer le courant de soudage par les chaines de levage, câbles de grue, ou autres circuits. Cela peut provoquer des risques dʼincendie ou dʼechauffement des chaines et des câbles jusquʼà ce quʼils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage. Ceci est particuliérement important pour le soudage de tôles galvanisées plombées, ou cadmiées ou tout autre métal qui produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant dʼopérations de dégraissage, nettoyage ou pistolage. La chaleur ou les rayons de lʼarc peuvent réagir avec les vapeurs du solvant pour produire du phosgéne (gas fortement toxique) ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté, voir le code “Code for safety in welding and cutting” CSA Standard W 117.2-1974.

PRÉCAUTIONS DE SÛRETÉ POUR

3. Un coup dʼarc peut être plus sévère quʼun coup de soliel, donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi quʼun verre blanc afin de se protéger les yeux du rayonnement de lʼarc et des projections quand on soude ou quand on regarde lʼarc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de lʻarc.

c. Protéger lʼautre personnel travaillant à proximité au

soudage à lʼaide dʼécrans appropriés et non-inflammables.

4. Des gouttes de laitier en fusion sont émises de lʼarc de soudage. Se protéger avec des vêtements de protection libres de lʼhuile, tels que les gants en cuir, chemise épaisse, pantalons sans revers, et chaussures montantes.

LES MACHINES À SOUDER À TRANSFORMATEUR ET À REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code de lʼélectricité et aux recommendations du fabricant. Le dispositif de montage ou la piece à souder doit être branché à une bonne mise à la terre.

2. Autant que possible, Iʼinstallation et lʼentretien du poste seront effectués par un électricien qualifié.

3. Avant de faires des travaux à lʼinterieur de poste, la debrancher à lʼinterrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur place.

Page 6

SAFETY

Electromagnetic Compatibility (EMC)

Conformance

Products displaying the CE mark are in conformity with European Community Council Directive of 15 Dec 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility, 2004/108/EC. It was manufactured in conformity with a national standard that implements a harmonized standard: EN 60974-10 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment. It is for use with other Lincoln Electric equipment. It is designed for industrial and professional use.

Introduction

All electrical equipment generates small amounts of electromagnetic emission. Electrical emission may be transmitted through power lines or radiated through space, similar to a radio transmitter. When emissions are received by other equipment, electrical interference may result. Electrical emissions may affect many kinds of electrical equipment; other nearby welding equipment, radio and TV reception, numerical controlled machines, telephone systems, computers, etc. Be aware that interference may result and extra precautions may be required when a welding power source is used in a domestic establishment.

Installation and Use

The user is responsible for installing and using the welding equipment according to the manufacturer’s instructions. If electromagnetic disturbances are detected then it shall be the responsibility of the user of the welding equipment to resolve the situation with the technical assistance of the manufacturer. In some cases this remedial action may be as simple as earthing (grounding) the welding circuit, see Note. In other cases it could involve construction of an electromagnetic screen enclosing the power source and the work complete with associated input filters. In all cases electromagnetic disturbances must be reduced to the point where they are no longer troublesome.

Note: The welding circuit may or may not be earthed for safety reasons according to national codes.

Changing the earthing arrangements should only be authorized by a person who is competent to access whether the changes will increase the risk of injury, e.g., by allowing parallel welding current return paths which may damage the earth circuits of other equipment.

Assessment of Area

Before installing welding equipment the user shall make an assessment of potential electromagnetic problems in the surrounding area. The following shall be taken into account:

a) other supply cables, control cables, signaling and telephone cables; above, below and adjacent to the

welding equipment;

b) radio and television transmitters and receivers;

c) computer and other control equipment;

d) safety critical equipment, e.g., guarding of industrial equipment;

e) the health of the people around, e.g., the use of pacemakers and hearing aids;

f) equipment used for calibration or measurement

g) the immunity of other equipment in the environment. The user shall ensure that other equipment being

used in the environment is compatible. This may require additional protection measures;

h) the time of day that welding or other activities are to be carried out.

Page 7

SAFETY

Electromagnetic Compatibility (EMC)

The size of the surrounding area to be considered will depend on the structure of the building and other activities that are taking place. The surrounding area may extend beyond the boundaries of the premises.

Methods of Reducing Emissions

Mains Supply

Welding equipment should be connected to the mains supply according to the manufacturer’s recommendations. If interference occurs, it may be necessary to take additional precautions such as filtering of the mains supply. Consideration should be given to shielding the supply cable of permanently installed welding equipment, in metallic conduit or equivalent. Shielding should be electrically continuous throughout its length. The shielding should be connected to the welding power source so that good electrical contact is maintained between the conduit and the welding power source enclosure.

Maintenance of the Welding Equipment

The welding equipment should be routinely maintained according to the manufacturer’s recommendations. All access and service doors and covers should be closed and properly fastened when the welding equipment is in operation. The welding equipment should not be modified in any way except for those changes and adjustments covered in the manufacturers instructions. In particular, the spark gaps of arc striking and stabilizing devices should be adjusted and maintained according to the manufacturer’s recommendations.

vivi

Welding Cables

The welding cables should be kept as short as possible and should be positioned close together, running at or close to floor level.

Equipotential Bonding

Bonding of all metallic components in the welding installation and adjacent to it should be considered. However, metallic components bonded to the work piece will increase the risk that the operator could receive a shock by touching these metallic components and the electrode at the same time. The operator should be insulated from all such bonded metallic components.

Earthing of the Workpiece

Where the workpiece is not bonded to earth for electrical safety, not connected to earth because of its size and position, e.g., ships hull or building steelwork, a connection bonding the workpiece to earth may reduce emissions in some, but not all instances. Care should be taken to prevent the earthing of the workpiece increasing the risk of injury to users, or damage to other electrical equipment. Where necessary, the connection of the workpiece to earth should be made by a direct connection to the workpiece, but in some countries where direct connection is not permitted, the bonding should be achieved by suitable capacitance, selected according to national regulations.

Screening and Shielding

Selective screening and shielding of other cables and equipment in the surrounding area may alleviate problems of interference. Screening of the entire welding installation may be considered for special

applications

_________________________

Portions of the preceding text are contained in EN 60974-10: “Electromagnetic Compatibility (EMC) product standard for arc welding equipment.”

Page 8

Thank You

viivii

for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product

••• as much pride as we have in bringing this product to you!

The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equipment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric for advice or information about their use of our products. We respond to our customers based on the best information in our possession at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such information or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customerʼs particular purpose, with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any warranty with respect to the sale of our products.

Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in applying these types of fabrication methods and service requirements.

Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com for any updated information.

CUSTOMER ASSISTANCE POLICY

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims for material damaged in shipment must be made by the purchaser against the transportation company at the time the shipment is received.

Please record your equipment identification information below for future reference. This information can be found on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information you have recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

“Product Registration”. Please complete the form and submit your registration.

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection. The level of seriousness to be applied to each is explained below:

WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.

CAUTION

This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.

Page 9

TABLE OF CONTENTS

Page

Installation.......................................................................................................................Section A

Technical Specifications ...............................................................................................A-1, A-2

Safety Precautions ...............................................................................................................A-3

Location, Lifting .............................................................................................................A-3

Stacking ........................................................................................................................A-3

Tilting.............................................................................................................................A-3

Input and Ground Connections .....................................................................................A-3

Machine Grounding.......................................................................................................A-3

High Frequency Protection............................................................................................A-3

Input Connection ..................................................................................................................A-4

Input Fuse and Supply Wire..........................................................................................A-4

Input Voltage Selection .................................................................................................A-4

Power Cord Replacement .............................................................................................A-4

Recommended Work Cable Sizes ................................................................................A-5

Remote Sense Lead Specifications, Semi Automatic Welding .....................................A-5

Polarity ..........................................................................................................................A-5

Cable Connections ...............................................................................................................A-6

Cable Inductance and its Effects on Welding................................................................A-6

Shielding Gas Connections ..................................................................................................A-7

Loading Spool Wire ..............................................................................................................A-8

Procedure to Install Drive Rolls and Wire Guides .........................................................A-8

Gun Used ......................................................................................................................A-8

Feeding Electrode and Brake Adjustment.....................................................................A-9

Drive Roll Pressure Setting ...........................................................................................A-9

TIG Welding .......................................................................................................................A-10

SMAW Welding ...........................................................................................................A-10

________________________________________________________________________________

viiiviii

Operation.........................................................................................................................Section B

Safety Precautions ...............................................................................................................B-1

Graphic Symbols...........................................................................................................B-1

Power-Up Sequence .....................................................................................................B-1

Duty Cycle.....................................................................................................................B-1

Product Description ..............................................................................................................B-2

Recommended Processes and Equipment ..........................................................................B-2

Equipment Limitations ..........................................................................................................B-3

Common Equipment Packages.....................................................................................B-3

Design Features............................................................................................................B-3

Case Front Controls .............................................................................................................B-4

Case Back Controls..............................................................................................................B-5

Internal Controls ...................................................................................................................B-6

Making a Weld with Waveform Technology Power Sources ................................B-7 thru B-16

Saving and Recalling a Memory ........................................................................B-17 thru B-19

2 Step - 4 Step Trigger Operation and Graphics ................................................B-20 thru B-25

Cold Feed/Gas Purge Switch .............................................................................................B-26

Set-Up Feature Menu ........................................................................................B-27 thru B-35

________________________________________________________________________________

Accessories.....................................................................................................Section C

General Options / Accessories..............................................................................C-1

TIG Options / Accessories.....................................................................................C-1

Wire Feed Options...............................................................................................................

C-1

________________________________________________________________________

Page 10

TABLE OF CONTENTS

Page

Maintenance ....................................................................................................Section D

Safety Precautions ...............................................................................................................D-1

Routine Maintenance ...........................................................................................................D-1

Periodic Maintenance...........................................................................................................D-1

Calibration Specification.......................................................................................................D-1

________________________________________________________________________________

Troubleshooting..............................................................................................Section E

Safety Precautions.................................................................................................E-1

How to Use Troubleshooting Guide.......................................................................E-1

Using Status LED and Error Fault Codes .....................................................................E-2, E-4

Troubleshooting Guide.............................................................................E-2 thru E-5

Error Fault Codes .........................................................................................................E-6, E-7

________________________________________________________________________________

Wiring Diagram and Dimension Print............................................................Section F

________________________________________________________________________

Parts Pages ................................................................................................................P-635 Series

_______________________________________________________________________

________

ixix

Page 11

A-1

INSTALLATION

TECHNICAL SPECIFICATIONS - POWER WAVE® C300 CE

POWER SOURCE-INPUT VOLTAGE AND CURRENT

Model

Duty Cycle

Input Voltage ± 10%

Input Amperes

Idle Power

A-1

Power Factor @

Rated Output

K2865-1

Process

GMAW

GMAW-Pulse

FCAW

SMAW

GTAW-DC

FREQUENCY

40% rating

100% rating

Duty Cycle

40%

100%

40%

100%

40%

100%

INPUT

VOLTAGE /

PHASE/

208/230/400*/460/575

3 phase 50/60 Hz

(* includes 380V to 415V)

30/28/16/14/11

23/21/12/11/9

300 Watts Max.

(fan on)

RATED OUTPUT

Volts at Rated Amperes

26.5

31.2

RECOMMENDED INPUT WIRE AND FUSE SIZES

INPUT AMPERE

RATING ON

NAMEPLATE

CORD SIZES

AWG SIZES (mm2)

.95

Amperes

300

250

280

225

300

250

TIME DELAY FUSE

OR BREAKER SIZE 2(AMPS)

208/3/50/60 230/3/50/60 400/3/50/60 460/3/50/60 575/3/50/60

Cord and Fuse Sizes based upon the U.S. National Electric Code and maximum output for 40°C (104°) ambient.

Also called “inverse time” or “thermal/magnetic” circuit breakers; circuit breakers that have a delay in tripping action that decreases as the magnitude of current increases.

Type SO cord or similar in 30° C ambient.

30 28 16 14 11

8 (10) 8 (10)

12 (4) 14 (2.5) 14 (2.5)

40 40 25 20 15

POWER WAVE® C300 CE

Page 12

A-2

WFS RANGE

INSTALLATION

WIRE FEED SPEED RANGE-WIRE SIZE

GMAW

MILD STEEL

WIRE SIZES

GMAW

ALUMINUM

WIRE SIZES

GMAW

STAINLESS

WIRE SIZES

A-2

FCAW

WIRE SIZES

50 – 700 ipm

(1.3 – 17.8 m/min)

PROCESS

GMAW

GMAW-Pulse

FCAW

GTAW-DC

SMAW

MODEL

K2865-1

(0.6 – 1.1mm)

Wire Speed

HEIGHT

18.80in (478mm)

.025 – .045"

.030 – 3/64"

(0.8 – 1.2mm)

WELDING PROCESS

OUTPUT RANGE (AMPERES)

40-300

5-300 5-280

WIRE SPEED RANGE

PHYSICAL DIMENSIONS

WIDTH

14.00in (356mm)

TEMPERATURE RANGES

.035 – .045"

(0.9 – 1.1mm)

40-70 VDC average, 100V peak

24 VDC average, 100V peak 60 VDC average, 100V peak

50 – 700 IPM (1.27 – 17.8 m/minute)

DEPTH

27.43in (697mm)

.035 – .052"

(0.9 – 1.4mm)

OCV (Uo)

WEIGHT

100lbs (47.6kg)*

OPERATING TEMPERATURE RANGE

Environmentally Hardened: -4°F to 104°F (-20°C to 40°C)

IP23 155º(F) Insulation Class

* Weight does not include input cord.

Thermal tests have been performed at ambient temperature. The duty cycle (duty factor) at 40°C has been determined by simulation.

STORAGE TEMPERATURE RANGE

Environmentally Hardened: -40°F to 185°F (-40°C to 85°C)

POWER WAVE® C300 CE

Page 13

A-3

INSTALLATION

A-3

SAFETY PRECAUTIONS

Read this entire installation section before you

start installation.

WARNING

ELECTRIC SHOCK can kill.

• Only qualified personnel should perform this installation.

• Turn the input power OFF at the

disconnect switch or fuse box before working on this equipment. Turn off the input power to any other equipment connected to the welding system at the disconnect switch or fuse box before working on the equipment.

• Do not touch electrically hot parts.

• Always connect the POWER WAVE® C300 CE

grounding lug (located inside the reconnect input access door) to a proper safety (Earth) ground.

------------------------------------------------------------------------

LIFTING

Both handles should be used when lifting POWER WAVE® C300 CE. When using a crane or overhead device a lifting strap should be connected to both handles. Do not attempt to lift the POWER WAVE® C300 CE with accessories attached to it.

Do not weld with the POWER WAVE® C300 CE while the machine is suspended by the handles.

WARNING

• Lift only with equipment of adequate lifting capacity.

• Be sure machine is stable when lifting.

• Do not operate machine while suspended when lifting.

FALLING

EQUIPMENT can

cause injury.

-----------------------------------------------------------------------------------------------

STACKING

The POWER WAVE® C300 CE cannot be stacked.

SELECT SUITABLE LOCATION

The POWER WAVE® C300 CE will operate in harsh environments. Even so, it is important that simple preventative measures are followed in order to assure long life and reliable operation.

• The machine must be located where there is free circulation of clean air such that air movement in the back, out the sides and bottom will not be restricted.

• Dirt and dust that can be drawn into the machine should be kept to a minimum. The use of air filters on the air intake is not recommended because normal air flow may be restricted. Failure to observe these precautions can result in excessive operating temperatures and nuisance shutdown.

• Keep machine dry. Shelter from rain and snow. Do not place on wet ground or in puddles.

• Do not mount the POWER WAVE® C300 CE over combustible surfaces. Where there is a combustible surface directly under stationary or fixed electrical equipment, that surface shall be covered with a steel plate at least .060” (1.6mm) thick, which shall extend not less than

5.90” (150mm) beyond the equipment on all sides.

TILTING

Place the machine directly on a secure, level surface or on a recommended undercarriage. The machine may topple over if this procedure is not followed.

INPUT AND GROUND CONNECTIONS

Only a qualified electrician should connect the POWER WAVE® C300 CE. Installation should be made in accordance with the appropriate National Electrical Code, all local codes and the information in this manual.

MACHINE GROUNDING

The frame of the welder must be grounded. A ground terminal marked with a ground symbol is located next to the input power connection block.

See your local and national electrical codes for proper grounding methods.

HIGH FREQUENCY PROTECTION

The EMC classification of the POWER WAVE® C300 CE is Industrial, Scientific and Medical (ISM) group 2, class A. The POWER WAVE® C300 CE is for industrial use only. (See Electromagnetic Compatibility EMC Safety Section).

Locate the POWER WAVE® C300 CE away from radio controlled machinery. The normal operation of the POWER WAVE® C300 CE may adversely affect the operation of RF controlled equipment, which may result in bodily injury or damage to the equipment.

POWER WAVE® C300 CE

Page 14

A-4

INSTALLATION

INPUT CONNECTION

WARNING

Only a qualified electrician should connect the input leads to the POWER WAVE® C300 CE. Connections should be made in

accordance with all local and national electrical codes and the connection diagram located on the inside of the reconnect access door of the machine. Failure to do so may result in bodily injury or death.

A-4

WARNING

The POWER WAVE® C300 CE ON/OFF switch is not intended as a service disconnect for this equipment. Only a qualified electrician should connect the input leads to

the POWER WAVE® C300 CE. Connections should be made in accordance with all local and national electrical codes and the connection diagram located on the inside of the reconnect access door of the machine. Failure to do so may result in bodily injury or death.

------------------------------------------------------------------------

The supply cable provided with the Power Wave C300 CE is rated for 450 VAC (line-to-neutral). Replace the supply cable in accordance with all national and local codes when operating at higher voltages.

A 15 ft. (4.6m) power cord is provided and wired into the machine.

Single Phase Input not supported. Three Phase Input

Connect green/yellow lead to ground per National Electric Code.

Connect grey, brown and black leads to power.

INPUT FUSE AND SUPPLY WIRE CONSIDERATIONS

Refer to Specification Section for recommended fuse, wire sizes and type of the copper wires. Fuse the input circuit with the recommended super lag fuse or delay type breakers (also called "inverse time" or "thermal/magnetic" circuit breakers). Choose input and grounding wire size according to local or national electrical codes. Using input wire sizes, fuses or circuit breakers smaller than recommended may result in "nuisance" shut-offs from welder inrush currents, even if the machine is not being used at high currents.

------------------------------------------------------------------------

POWER CORD REPLACEMENT

WARNING

Only a qualified electrician should connect the input leads to the POWER WAVE® C300 CE. Connections should be made in accordance with all local and

national electrical codes and the connection diagram located on the inside of the reconnect access door of the machine. Failure to do so may result in bodily injury or death.

------------------------------------------------------------------------

If the input power cord is damaged or needs to be replaced an input power connection block is located in the access panel under the wire spool.

ALWAYS CONNECT THE POWER WAVE GROUNDING LUG (LOCATED INSIDE THE ACCESS PANEL) TO A PROPER SAFETY (EARTH) GROUND.

FIGURE A.1

INPUT VOLTAGE SELECTION

The POWER WAVE® C300 CE automatically adjusts to work with different input voltages. No reconnect switches settings are required.

POWER WAVE® C300 CE

Page 15

A-5

INSTALLATION

A-5

RECOMMENDED WORK CABLE SIZES FOR ARC WELDING

A work cable is provided with the POWER WAVE® C300 CE. This cable is appropriately sized for all of the POWER WAVE® C300 CEʼs welding procedures. If the work cable needs to be replaced a similar quality of cable should be used as excessive voltage drops caused by undersized welding cables can result in unsatisfactory welding performance. Always use the largest work cables that is practical, and be sure all connections are clean and tight.

Note: Excessive heat in the weld circuit indicates undersized cables and/or bad connections.

REMOTE SENSE LEAD SPECIFICATIONS

Since the POWER WAVE® C300 CE has the ability to be in close proximity to the welding arc, the POWER WAVE® C300 CE does not require the use of remote sense leads.

SEMI-AUTOMATIC WELDING POLARITY

The Fast Mate adapter is permanently wired for Electrode Positive welding for all GMAW and FCAW processes.

The polarity for GTAW and SMAW processes is determined by connecting the electrode lead to either the + or – output stud on the front of the machine

POWER WAVE® C300 CE

Page 16

A-6

INSTALLATION

CABLE CONNECTION

There is one circular connection on the front of the machine. (See Figure A.2---Table A.1)

FIGURE A.2

Function

TABLE A.1

A-6

Wiring

12 pin connector for Push pull guns; foot pedal; remote controls; Hand –amptrols.

CABLE INDUCTANCE AND ITS EFFECTS ON WELDING

Whenever possible always weld in a direction away from the work (ground) connection.

Excessive cable inductance will cause the welding performance to degrade. There are several factors that contribute to the overall inductance of the cabling system including cable size, and loop area. The loop area is defined by the separation distance between the electrode and work cables, and the overall welding loop length. The welding loop length is defined as the total of length of the electrode cable (A) + work cable (B) + work path (C) (see Figure A.3).

A B C D E

F G H

J K

L M

Remote Pot Common

Remote Pot +10VDC

ArcLink Peripheral Sense

To minimize inductance always use the appropriate size cables, and whenever possible, run the electrode and work cables in close proximity to one another to minimize the loop area. Since the most significant factor in cable inductance is the welding loop length, avoid excessive lengths and do not coil excess cable. For long work piece lengths, a sliding ground should be considered to keep the total welding loop length as short as possible.

For additional Safety information regarding the electrode and work cable set-up, See the standard “SAFETY INFORMATION” located in the front of this Instruction Manual.

CANL

CANH

Remote Pot Wiper

Trigger Trigger

Power Common

Power +

Motor Negative

Motor Positive

FIGURE A.3

POWER WAVE® C300 CE

WORK

Page 17

A-7

INSTALLATION

A-7

SHIELDING GAS CONNECTION

WARNING

CYLINDER may explode if

damaged.

• Keep cylinder upright and chained to support.

• Keep cylinder away from areas where it may be damaged.

• Never lift welder with cylinder attached.

• Never allow welding electrode to touch cylinder.

• Keep cylinder away from welding or other live electrical circuits.

• BUILD UP OF SHIELDING GAS MAY HARM HEALTH OR KILL.

• Shut off shielding gas supply when not in use.

• See American National Standard Z-49.1, "Safety in Welding and Cutting” Published by the American Welding Society.

------------------------------------------------------------------------

Customer must provide a cylinder of shielding gas, a pressure regulator, a flow control valve, and a hose from the flow valve to the gas inlet fitting of the wire drive unit. Connect a supply hose from the gas cylinder flow valve outlet to the 5/8-18 female inert gas fitting on the back panel of the

POWER WAVE® C300 CE.

5. Attach one end of the inlet hose to the outlet fitting of the flow regulator. Attach the other end to the welding system shielding gas inlet. Tighten the union nuts with a wrench.

6. Before opening the cylinder valve, turn the regulator adjusting knob counterclockwise until the adjusting spring pressure is released.

7. Standing to one side, open the cylinder valve slowly a fraction of a turn. When the cylinder pressure gage stops moving, open the valve fully.

8. The flow regulator is adjustable. Adjust it to the flow rate recommended for the procedure and process being used before making a weld.

MAXIMUM INLET PRESSURE IS 100 PSI. (6.9 BAR.)

Install the shielding gas supply as follows:

1. Secure the cylinder to prevent it from falling.

2. Remove the cylinder cap. Inspect the cylinder valves and regulator for damaged threads, dirt, dust, oil or grease. Remove dust and dirt with a clean cloth. DO

NOT ATTACH THE REGULATOR IF OIL, GREASE OR DAMAGE IS PRESENT! Inform your gas supplier

of this condition. Oil or grease in the presence of high pressure oxygen is explosive.

3. Stand to one side away from the outlet and open the cylinder valve for an instant. This blows away any dust or dirt which may have accumulated in the valve outlet.

4. Attach the flow regulator to the cylinder valve and tighten the union nut(s) securely with a wrench. Note: if connecting to 100% CO2cylinder, insert regulator adapter between regulator and cylinder valve. If adapter is equipped with a plastic washer, be sure it is seated for connection to the CO2cylinder.

POWER WAVE® C300 CE

Page 18

A-8

INSTALLATION

A-8

LOADING SPOOLS OF WIRE

WARNING

• Keep hands, hair, clothing and tools away from rotating equipment.

• Do not wear gloves when threading

wire or changing wire spool.

• Only qualified personnel should install,

use or service this equipment.

------------------------------------------------------------------------

Loading 10 to 15 lb. (4.5 – 6.8kg) Spools.

A K468 spindle adapter is required for 8" (203.2mm) spools.

1. Squeeze the release bar on the retaining collar and

remove it from the spindle.

Place the spindle adapter on the spindle, aligning

the spindle brake pin with the hole in the adapter.

3. Place the spool on the spindle and align the

adapter brake tab with one of the holes in the back side of the spool. An indicator mark on the end of the spindle shows the orientation of the brake tab. Be certain the wire feeds off of the spool in the proper direction.

PROCEDURE TO INSTALL DRIVE ROLLS AND WIRE GUIDES

WARNING

• Turn the input power OFF at the welding power source before installation or changing drive rolls and/or guides.

• Do not touch electrically live parts.

• When inching with the gun trigger, electrode and drive mechanism are "hot" to work and ground and could remain energized several seconds after the gun trigger is released.

• Do not operate with covers, panels or guards removed or open.

• Only qualified personnel should perform maintenance work.

------------------------------------------------------------------------

1. Turn power off at the welding power source.

2. Release the idle roll pressure arm.

3. Remove the outer wire guide by turning the knurled

thumbscrews counter-clockwise to unscrew them from the feed plate.

Rotate the triangular lock and remove the drive

rolls. (See Figure A.5)

FIGURE A.5

4. Re-install the retaining collar. Make sure that the release bar snaps out and that the retaining collar fully engages the groove on the spindle.

Loading 16 to 44 lb. (7.3 – 20kg) Spools

1. Squeeze the release bar on the retaining collar and remove it from the spindle.

2. Place the spool on the spindle, aligning the spindle brake pin with one of the holes in the back side of the spool. An indicator mark on the end of the spindle shows the orientation of the brake holding pin. Be certain the wire feeds off of the spool in the proper direction.

3. Re-install the retaining collar. Make sure that the release bar snaps out and that the retaining collar fully engages the groove on the spindle

5. Remove the inner wire guide.

6. Insert the new inner wire guide, groove side out, over the two locating pins in the feed plate.

7. Install a drive roll on each hub assembly secure with the triangular lock.

8. Install the outer wire guide by aligning it with the pins and tightening the knurled thumbscrews.

9. Close the idle arm and engage the idle roll pressure arm. Adjust the pressure appropriately.

GUN USED

The Magnum 350 PRO is the recommended gun for the POWER WAVE® C300 CE. Refer to the Magnum Proʼs operators manual for installation instructions.

POWER WAVE® C300 CE

Page 19

A-9

INSTALLATION

FEEDING ELECTRODE AND BRAKE ADJUSTMENT

DRIVE ROLL PRESSURE SETTING

ELECTRIC SHOCK can kill.

• Turn the input power OFF at the welding power source before installation or changing drive rolls and/or guides.

• Do not touch electrically live parts.

• When feeding with the gun trigger, unless “COLD FEED” trigger mode is selected, the electrode and drive mechanism are always “HOT” to work and ground and could remain “HOT” several seconds after the gun trigger is released.

• Do not operate with covers, panels or guards removed or open

• Only qualified personnel should perform maintenance work.

------------------------------------------------------------------------

The POWER WAVE® C300 CEʼs optimum drive roll pressure varies with type of wire, surface condition, lubrication, and hardness. Too much pressure could cause birdnesting”, but too little pressure could cause wire feed slippage with load and/or acceleration. The optimum drive roll setting can be determined as follows:

A-9

PRESSURE ARM ADJUSTMENT

The pressure arm controls the amount of force the drive rolls exert on the wire. Proper adjustment of pressure arm gives the best welding performance.

Set the pressure arm as follows (See Figure A.6):

Aluminum wires between 1 and 3 Cored wires between 3 and 4 Steel, Stainless wires between 4 and 6

FIGURE A.6

Cored wires

FLUX CORE ARC WELDING

1 3

2 4 6

ALUMINUM

GAS METAL ARC WELDING

Aluminum wires

Steel, Stainless wires

Turn the Reel or spool until the free end of the

1. electrode is accessible.

2. While tightly holding the electrode, cut off the bent end and straighten the first 6" (150 mm). Cut off the first 1" (25 mm). (If the electrode is not properly straightened, it may not feed or may jam causing a "birdnest".)

3. Insert the free end through the incoming guide tube.

4. Press the Cold Inch key and push the electrode into the drive roll.

5. Feed the electrode through the gun.

6. Adjust the brake tension with the thumbscrew on the spindle hub, until the reel turns freely but with little or no overrun when wire feeding is stopped. Do not over tighten.

POWER WAVE® C300 CE

Page 20

A-10

INSTALLATION

A-10

TIG WELDING

(Figure A.7)

When TIG (GTAW) welding with the Power Wave C300CE, a torch with an integral gas valve is required.

FIGURE A.7

(OPTIONAL) FOOT AMPTROL

RECEPTACLE TO REMOTE CONTROL

TIG TORCH GAS HOSE

CONNECTION TO GAS SUPPLY POWER CABLE

STUD (-) TO NEGATIVE

WORK PIECE

WORK CLAMP

STUD (+) TO POSITIVE

SMAW WELDING

Most SMAW welding procedures use Electrode Positive welding. For these applications, connect the stick electrode holder to the positive (+) output stud and connect the work clamp to the negative (-) output stud.

Some SMAW welding procedures use Electrode Negative Polarity. For these applications, connect the stick electrode holder to the negative (-) output stud and connect the work clamp to the positive (+) output stud.

WORK CLAMP

WORK PIECE

POWER CABLE

TO POSITIVE STUD (+)

TIG TORCH

TO NEGATIVE STUD (-)

TO GAS SUPPLY CONNECTION

GAS HOSE

TO REMOTE CONTROL RECEPTACLE

FOOT AMPTROL (OPTIONAL)

POWER WAVE® C300 CE

Page 21

B-1

OPERATION

B-1

SAFETY PRECAUTIONS

READ AND UNDERSTAND ENTIRE SECTION BEFORE OPERATING MACHINE.

WARNING

• ELECTRIC SHOCK CAN KILL. Unless using COLD FEED feature, when feeding with gun trigger, the electrode and drive mechanism are always electrically energized and could remain energized several seconds after the welding ceases.

• Do not touch electrically live part or electrode with skin or wet clothing.

• Insulate yourself from work and ground.

• Always wear dry insulating gloves.

• Do not operate with covers, panels or guards removed or open.

---------------------------------------------------------------------

• FUMES AND GASSES can be dangerous.

• Keep your head out of fumes.

• Use ventilation or exhaust to remove fumes from breathing zone.

---------------------------------------------------------------------

WELDING SPARKS can cause

• fire or explosion.

• Keep flammable material away.

GRAPHIC SYMBOLS THAT APPEAR ON THIS MACHINE OR IN THIS MANUAL

WARNING OR CAUTION

DANGEROUS VOLTAGE

POSITIVE OUTPUT

NEGATIVE OUTPUT

HIGH TEMPERATURE

STATUS

PROTECTIVE GROUND

---------------------------------------------------------------------

ARC RAYS can burn.

• Wear eye, ear and body protection.

---------------------------------------------------------------------

SEE ADDITIONAL WARNING INFORMATION UNDER ARC WELDING SAFETY PRECAUTIONS AND IN THE FRONT OF THIS OPERATING MANUAL.

---------------------------------------------------------------------

EXPLOSION

POWER-UP SEQUENCE

When the POWER WAVE® C300 CE is powered it can take as long as 30 seconds for the machine to be ready to weld. During this time period the user inter-

face will not be active.

DUTY CYCLE

The POWER WAVE® C300 CE is rated at 250 amps at 26.5 volts with a 100% duty cycle. It is further rated to provide 300 amps at 29 volts with a 40% duty cycle. The duty cycle is based on a ten-minute period. A 40% duty cycle represents 4 minutes of welding and 6

minutes of idling in a ten-minute period.

POWER WAVE® C300 CE

Page 22

B-2

OPERATION

PRODUCT DESCRIPTION

The POWER WAVE® C300 CE is a high performance multi-process machine with GMAW, FCAW, SMAW, DC TIG, and pulse capability. It will offer a premier welding performance solution for specific areas such as aluminum, stainless, nickel where size and weight are an issue.

The POWER WAVE® C300 CE will provide the following:

B-2

PROCESS LIMITATIONS

The software based weld tables of the POWER WAVE® C300 CE limit the process capability within the output range and the safe limits of the machine. In general the processes will be limited to .025-.045 solid steel wire, .035-.045 stainless wire, .035-.052 cored wire, and .035 and 3/64 Aluminum wire. 1/16 Aluminum wire is not supported.

The following items will not be supported on this product, but may be supported by other product in the product portfolio:

• Power - 300A @ 40%, 250A @ 100%.

• Multi Input Voltage with no reconnect - 200-600V, 50-60 Hz input.

• Three Phase Power.

• < 95% Power factor – optimizes available electrical capacity.

• Environmentally Hardened - IP23 rated for operating in difficult environments.

• Versatile Feeding Options – FastMate Mig guns, Spool guns, and Push-pull guns.

• Ethernet connectivity – allows access to the Power Wave utilities software tools.

RECOMMENDED PROCESSES AND EQUIPMENT

RECOMMENDED PROCESSES

The POWER WAVE® C300 CE is a high speed, multiprocess power source capable of regulating the current, voltage, or power of the welding arc. With an output range of 5 to 300 amperes, it supports a number of standard processes including synergic GMAW, GMAW-P, FCAW, FCAW-SS, SMAW, GTAW and GTAW-P on various materials especially steel, aluminum and stainless steel.

• STT

• AC welding processes

WARNING

The POWER WAVE® C300 CE is not recommended for pipe thawing.

---------------------------------------------------------------------

EQUIPMENT LIMITATIONS

• Maximum gun length is 25 ft (7.6m) for push-only systems.

• Maximum gun length is 50 ft (15.2) for push-pull systems.

• Maximum spool size is 12 in (305 mm) diameter.

• Maximum spool weight is 44 lb (20 kg).

• The Fast Mate Adapter is integral to the machine and cannot be changed to other gun bushings

• Wire welding processes are limited to positive polarity only.

• Does not operate on single phase power

The following capabilities are supported:

• Push-pull (12-pin) connection - Panther™ and Cougar™.

• Spool gun connection (K2490-1 and K2519-1).

• Remote foot pedal (K870) or hand amptrol (K963-3) via a 12-pin connection.

• Standard MIG gun trigger connection, Integrated in Euro Connector.

• The Gun bushing with Euro Connector installed. Cannot be changed to other gun bushings.

• Watercooler, Integral CoolArc 50.

• Simple process to switch between different welding processes.

POWER WAVE® C300 CE

Page 23

B-3

OPERATION

B-3

DESIGN FEATURES

Loaded with Standard Features

• Multiple process DC output range: 5 - 300 Amps.

• 208 – 575 VAC, 3 phase, 50-60Hz input power.

• New and Improved Line Voltage Compensation

holds the output constant over wide input voltage fluctuations.

• Utilizes next generation microprocessor control,

based on the ArcLink® platform.

• State of the art power electronics technology, yields

superior welding capability.

• Electronic over current protection.

• Input over voltage protection.

• F.A.N. (fan as needed). Cooling fan runs when the

output is energized 15 seconds following the strike of the welding arc and will continue to run 5 minutes following the end of the weld.

• Thermostatically protected for safety and reliability.

• Recessed connection panel for protection against

accidental impact.

• Ethernet connectivity.

• Panel mounted Status and Thermal LED indicators

facilitate quick and easy troubleshooting.

• Potted PC boards for enhanced ruggedness/reliabili-

ty.

• Enclosure reinforced with heavy duty aluminum

extrusions for mechanical toughness.

• Push-Pull ready for welding aluminum.

• Remote control/Foot amptrol ready.

• Waveform Control Technology™ for good weld

appearance and low spatter, even when welding nickel alloys.

• 8 memories for easily selecting procedures.

• Full sequence control for tailoring the weld from start

to end.

• Patented MAXTRAC™ 2 roll drive system.

• Patent pending drive rolls improve traction on solid

wire by up to 20%.

• The precision machined, rigid aluminum alloy frame

results in maximum drive roll clamping pressure.

• Patented split wire guides fully support the wire and

virtually eliminate birdnesting.

• No tools required to change the drive rolls and wire

guides.

• Patented dual spring pressure arms have sensitivity for feeding soft wires without crushing them, and have plenty of compression force for feeding solid or stiff wires.

• All gear driven rolls for more feeding force.

• Brass-to-brass connections between the electrode connection and the gun minimize voltage drop variations, resulting in consistent arc performance all day, every day.

• Powerful, quiet motor with integrated tachometer for accurate WFS regulation.

POWER WAVE® C300 CE

Page 24

B-4

CASE FRONT CONTROLS

7 14 6

13 5 12

4 10 3 9 2 8 1

OPERATION

FIGURE B.1

B-4

8 9

All operator controls and adjustments are located on the case front of the Power Wave. (See Figure B.1)

1. LEFT DISPLAY- Shows wire feed speed or amper-

age,

2. LEFT KNOB- Adjusts value in left display.

3. MAIN DISPLAY- Shows detailed welding and diag-

nostic information.

4. LEFT BUTTON- Changes the Main display to

show the Weld Mode or UltimArc™ Control or Memories.

5. ON/OFF SWITCH- Controls power to the Power

Wave C300CE.

9. RIGHT KNOB- Adjusts value in right display.

10. THERMAL LIGHT- Indicates when machine has

thermal fault.

11. SET-UP- Lights when machine is in set-up mode,

12. RIGHT BUTTON- Changes the Main display to

arc start, arc end and trigger options.

13. MAIN KNOB- Changes the values on the Main

display.

14. 12 PIN CONNECTOR- Connection for push pull

guns, remotes.

6. + OUTPUT STUD- Connection for electrode posi-

tive.

7. - OUTPUT STUD- Connection for electrode nega-

tive.

8. RIGHT DISPLAY- Shows voltage or trim.

POWER WAVE® C300 CE

Page 25

B-5

CASE BACK CONTROLS

OPERATION

FIGURE B.2

B-5

1. ETHERNET CONNECTOR

2. POWER CORD

3. GAS CONNECTION

4. CIRCUIT BREAKER

POWER WAVE® C300 CE

Page 26

B-6

OPERATION

INTERNAL CONTROLS

B-6

FIGURE B.3

1. SPINDLE BRAKE

2. WIRE DRIVE PRESSURE ARM

COLD INCH / GAS PURGE SWITCH

POWER WAVE® C300 CE

Page 27

B-7

OPERATION

B-7

MAKING A WELD WITH WAVEFORM TECHNOLOGY POWER SOURCES

WARNING

MAKING A WELD The serviceability of a product or structure utilizing the welding programs is and must be the sole responsibility of the builder/user. Many variables beyond the control of The Lincoln Electric Company affect the results obtained in applying these programs. These variables include, but are not limited to, welding procedure, plate chemistry and temperature, weldment design, fabrication methods and service requirements. The available range of a welding program may not be suitable for all applications, and the build/user is and must be solely responsible for welding program selection.

---------------------------------------------------------------------

Choose the electrode material, electrode size, shielding gas, and process (GMAW, GMAW-P etc.) appropriate for the material to be welded.

Select the weld mode that best matches the desired welding process. The standard weld set shipped with the Power Wave C300 encompasses a wide range of common processes that will meet most needs. If a special weld mode is desired, contact the local Lincoln Electric sales representative.

All adjustments are made through the user interface. Because of the different configuration options your system may not have all of the following adjustments. Regardless of availability, all controls are described in the following section ( See Figure B.4 Panel Controls Used)

WIRE FEED SPEED (WFS)

In synergic welding modes (synergic CV, GMAW-P), WFS is the dominant control parameter. The user adjusts WFS according to factors such as wire size, penetration requirements, heat input, etc. The Power Wave then uses the WFS setting to adjust the voltage and current according to settings contained in the Power Wave.

In non-synergic modes, the WFS control behaves like a conventional power source where WFS and voltage are independent adjustments. Therefore, to maintain proper arc characteristics, the operator must adjust the voltage to compensate for any changes made to the WFS.

AMPS

In constant current modes, this control adjusts the welding current.

VOLTS

In constant voltage modes, this control adjusts the welding voltage.

TRIM

In pulse synergic welding modes, the Trim setting adjusts the arc length. Trim is adjustable from 0.50 to 1.50. 1.00 is the nominal setting and is a good starting point for most conditions.

ULTIMARC

UltimArcTMControl allows the operator to vary the arc characteristics from “soft” to “crisp”. UltimArc™Control is adjustable from –10.0 to +10.0 with a nominal setting of 0.0.

CONTROL

DEFINITION OF WELDING MODES

NON-SYNERGIC WELDING MODES

• A Non-synergic welding mode requires all welding process variables to be set by the operator.

SYNERGIC WELDING MODES

• A Synergic welding mode offers the simplicity of single knob control. The machine will select the correct voltage and amperage based on the wire feed speed (WFS) set by the operator.

BASIC WELDING CONTROLS

WELD MODE

Selecting a weld mode determines the output characteristics of the Power Wave power source. Weld modes are developed with a specific electrode material, electrode size, and shielding gas. For a more complete description of the weld modes programmed into the Power Wave at the factory, refer to the Weld Set Reference Guide supplied with the machine or available at www.powerwavesoftware.com.

POWER WAVE® C300 CE

Page 28

B-8

Arc Control

End Options

Weld Mode

Start Options

Memories

Trigger Options

AMPS OFF

AMPS

LESS MORE

OUTPUT

Amps A

Trim V Volts

Wire Feed Speed (WFS)

Amps

OPERATION

B-8

CASE FRONT CONTROLS USED

Vol ts

Trim

Memories

Weld Mode

Arc Control

LESS AMPS

OUTPUT ON

Trigger Options

MORE AMPS

OUTPUT OFF

Start Options

End Options

POWER WAVE® C300 CE

Page 29

B-9

OPERATION

SMAW (STICK) WELDING

SMAW is most often used for outdoor construction, pipe welding and general repairs. The POWER WAVE® C300 CE controls Amperage, Output Control and Arc Force during SMAW welding.

During SMAW welding the wire drive remains idle.

BASIC OPERATION

B-9

CC STICK MODES

PROCESS

Stick Soft(7018)

Stick Crisp(6010)

Stick Pipe

MODE

OUTPUT ON

200

LESS AMPS

MORE AMPS

OUTPUT OFF

OFF

CONTROL OPTIONS

START OPTIONS

EFFECT / RANGE

START TIME: 0 TO 10 Seconds

If no remote control is installed, this control sets the time for the

DESCRIPTION

weld output to ramp up or down from a preset Start current to the preset Weld current. Use the WFS/AMP knob to adjust Start current while the Start Options LED is lit.

Stick Soft 7018

UltimArc™ Control

EFFECT / RANGE

ARC FORCE

(Soft)-10.0 to (Crisp)+10.0

DESCRIPTION

Arc

Force adjusts the short circuit current for a soft arc, or for a forceful, driving arc. Lower values will provide less short circuit and softer arc. Higher settings will provide a higher short circuit, a more forceful arc and possibly more spatter.

POWER WAVE® C300 CE

END OPTIONS

No arc ending options are active for SMAW

(Stick) Welding.

Page 30

B-10

OPERATION

NON-SYNERGIC GMAW AND FCAW WELDING

In non-synergic modes, the WFS control is similar to a conventional CV power source where WFS and voltage are independent adjustments. Therefore to maintain the arc characteristics, the operator must adjust the voltage to compensate for any changes made to the WFS.

B-10

UltimArc™Control, adjusts the apparent inductance of the wave shape. The UltimArc™Control adjustment is similar to the “pinch” function in that it is inversely proportional to inductance. Therefore, increasing UltimArc™Control greater than 0.0 results in a crisper arc (more spatter) while decreasing the UltimArc™Control to less than 0.0 provides a softer arc (less spatter).

put turns off. gas flows after the welding out-

0 To 10.0 Seconds Postflow Time

the time that shielding

Adjusts wire for the next arc start. and prepares the end of the wire from sticking in the puddle stops feeding. It prevents the output continues after the wire amount of time that the weld

0 To 0.25 Seconds The burnback time is the

Burnback: the Crater Procedure. from the Weld Procedure to machine will ramp up or down During the Crater time, the after the trigger is released. time at the end of the weld WFS and Volts for a specified Crater ProcedureCrater Procedure controls the (Crisp)+10.

0 effect in 4 Step trigger mode.

-ristics when short-arc welding.

(Soft)-10.0 to still pulled. The option has no Pinch controls the arc characte-

PINCH 0 To 120.0 Seconds

continue even if the trigger is DESCRIPTION

EFFECT / RANGE Spot Timer:

Adjusts the time welding will

UltimArc™ Control

EFFECT DESCRIPTION

END OPTIONS

STD CV

Gas Shld

Procedure. FCAW, (GS) STANDARD CV

7 to the preset Welding FCAW, (SS) STANDARD CV

6 down from the Start Procedure GMAW, POWER MODE

the machine will ramp up or the weld. During the start time,

GMAW, STANDARD CV

5 fied time at the beginning of

PROCESS

WELD MODE

the WFS and Volts for a speciThe Start Procedure controls

Start Procedure

WELD MODE

lished. is pulled until an arc is estabspeed from the time the trigger

Off, .076 To 3.81 in/min Run-In sets the wire feed

Run-In WFS

: andprior to feeding wire. flowsafter the trigger is pulled

0 To 10 Seconds that

Preflow Time

Adjusts the time

shielding gas

DESCRIPTION

EFFECT

START OPTIONS

AMPS

OFF LESS

OUTPUT

4.5020.0

WELD MODE

PROCESS

GMAW, STANDARD CV GMAW, POWER MODE FCAW, (SS) STANDARD CV

FCAW, (GS) STANDARD CV

BASIC OPERATION

4.50

LESS AMPS

CONTROL OPTIONS

WELD MODE

6 7

MORE AMPS

Gas Shld

STD CV

20.0

OUTPUT OFF

OUTPUT ON

EFFECT

Preflow Time

0 To 10 Seconds

Run-In WFS

Off, .076 To 3.81 in/min

Start Procedure

START OPTIONS

DESCRIPTION

Adjusts the flows

and

time

that

shielding

after the trigger is

prior to feeding wire. Run-In sets the wire feed speed from the time the trigger

is pulled until an arc is established. The Start Procedure controls the WFS and Volts for a specified time at the beginning of the weld. During the start time, the machine will ramp up or down from the Start Procedure to the preset Welding Procedure.

gas

pulled

EFFECT / RANGE

PINCH (Soft)-10.0 to (Crisp)+10.

UltimArc™ Control

DESCRIPTION

Pinch controls the arc characte-

-ristics when short-arc welding.

POWER WAVE® C300 CE

EFFECT

Spot Timer:

0 To 120.0 Seconds

Crater Procedure

Burnback:

0 To 0.25 Seconds

Postflow Time 0 To 10.0 Seconds

END OPTIONS

DESCRIPTION

Adjusts the time welding will continue even if the trigger is still pulled. The option has no effect in 4 Step trigger mode.

Crater Procedure controls the WFS and Volts for a specified time at the end of the weld after the trigger is released. During the Crater time, the machine will ramp up or down from the Weld Procedure to the Crater Procedure.

The burnback time is the amount of time that the weld output continues after the wire stops feeding. It prevents the wire from sticking in the puddle and prepares the end of the wire for the next arc start.

Adjusts

the time that shielding gas flows after the welding out put turns off.

Page 31

B-11

OPERATION

B-11

GMAW (MIG) SYNERGIC WELDING

In synergic welding modes, WFS is the dominant control parameter. For each wire feed speed, a corresponding voltage is programmed into the machine at the factory. The user adjusts WFS according to factors such as wire size, material thickness, penetration requirements, etc. The Power Wave then uses the WFS setting to select the appropriate voltage. The voltage selected will be a nominal voltage. The user can adjust the voltage higher or lower to compensate for material condition or individual preference.

BASIC OPERATION

CONTROL OPTIONS

ELECTRODE AND GAS

Steel Steel

Stainless

Stainless Aluminum 4043 Aluminum 5356

CO Ar(Mix) Ar(Mix)

Ar/He/CO

Ar Ar

WELD MODE

4.50

LESS AMPS

.08 .09 1.0 1.2

93 94 15 11 21

61 29 31 41 63 --- --- ---

--- --- --- 71

--- --- 151 75

MORE AMPS

WIRE SIZE

14 10 20

OUTPUT OFF

Synergic CV programs feature an ideal voltage best suited for most procedures. Use this voltage as a starting point and adjust if needed for personal preferences.

When the voltage knob is rotated, the display will show an upper or lower bar indicating if the voltage is above or below the ideal voltage.

• Preset voltage above ideal voltage. (upper bar displayed)

• Preset voltage at ideal voltage. (no bar displayed)

• Preset voltage below ideal voltage. (lower bar displayed)

OUTPUT ON

START OPTIONS

DESCRIPTION

Adjusts the time

gas

flows

pulled and Run-In sets the wire feed speed from the time the trigger is pulled until an arc is established. The Start Procedure controls the WFS, Volts at a specified time at the beginning of the weld. During the start time, the machine will ramp up or down from the Start Procedure to the preset Welding Procedure.

that shielding

after the

trigger

prior to feeding.

20.0

EFFECT Preflow Time:

0 To 10 Seconds

Run-in WFS: Off, 0.76 to 3.81 m/min.

Start Procedure

EFFECT / RANGE PINCH EFFECT (-10.0 to +10.0)

UltimArc™ Control

DESCRIPTION

Pinch controls the arc characte-

-ristics when short-arc welding.

POWER WAVE® C300 CE

STEEL 1.0mm

CV CO2

EFFECT

Spot Timer

0 to 120.0 Seconds

Crater Procedure

Burnback:

0 to 0.25 Seconds

Postflow Time

0 to 10 Seconds

END OPTIONS

DESCRIPTION

Adjust the time welding will continue even if the trigger is still pulled. This option has no effect in 4-Step Trigger Mode.

Adjusts the time that shielding gas flows after the welding output turns off.

Page 32

B-12

g g

OPERATION

STEEL AND STAINLESS SYNERGIC GMAW-P (PULSED MIG) WELDING

When pulse welding, the power source primarily regulates the arc current, not the arc voltage. During a pulsing cycle, arc current is regulated from a low background level to a high peak level and then back down to the low background level. The average arc voltage increases and decreases as the average arc current is increased or decreased. The peak current, back ground current, rise time, fall time and pulse frequency all affect the average voltage. Since the average voltage for a given wire feed speed can only be determined when all the pulsing waveform parameters are known, a unitless value called “trim” is used for adjusting the arc length.

Trim adjusts the arc length and ranges from 0.50 to

1.50 with a nominal value of 1.00. Increasing the trim value increases the arc length. Decreasing the trim value decreases the arc length.

Pulse welding modes are synergic; using wire feed speed as the main control parameter. As the wire feed speed is adjusted, the power source adjusts the waveform parameters to maintain good welding characteristics. Trim is used as a secondary control to change the arc length for material conditions or individual preference. (See

Figure B.5)

B-12

th Short

Arc Len Arc Len

th Medium

Arc Length Long Trim .50 Trim 1.00

Trim 1.50

Trim .50

Arc Len

th Short

FIGURE B.5

Trim 1.00

Arc Len

ULTIMARC™CONTROL (See Figure B.6)

UltimArc™Control adjusts the focus or shape of the arc. UltimArc™Control is adjustable from -10.0 to +10.0 with a nominal setting of 0.0. Increasing the arc control increases the pulse frequency and background current while decreasing the peak current.

Medium Frequency and Width

Low Frequency, Wide High Frequency, Focused UltimArc™ Control -10.0 OFF

UltimArc™ Control +10.0

UltimArc™ Control

FIGURE B.6

Trim 1.50

th Medium

Arc Length Long

This results in a tight, stiff arc used for high speed sheet metal welding. Decreasing the arc control decreases the pulse frequency and background current while increasing the peak current. This results in a soft arc good for out of position welding.

UltimArc™ Control -1 0 .0

Low F requency, Wide

UltimArc™ Control

Med ium Frequency and Wi dth

The Power Wave utilizes adaptive control to compensate for changes in the electrical stick-out(distance from the contact tip to the work piece) while welding. The Power Wave waveforms are optimized for a 5/8” to 3/4” stick out

OF F

UltimArc™ Control

High Frequency, Focused

The adaptive behavior supports a range of stick outs from approximately 1/2” to 1-1/4”. At low or high wire feed speeds, the adaptive range may be less due to physical limitations of the welding process.

+10.0

depending on the wire type and wire feed speed.

POWER WAVE® C300 CE

Page 33

B-13

OPERATION

STEEL AND STAINLESS GMAW-P (PULSED MIG) WELDING

BASIC OPERATION

B-13

ELECTRODE AND

Steel(Crisp) Steel(Rapid Arc) Steel(Vert Up) Stainless

Stainless Stainless

Stainless(Vert Up)

WELD MODE

GAS

Ar(Mix)

Ar/

Ar/He/CO Ar(Mix)

WFS

AMPS

Less Deposition

4.50

CONTROL OPTIONS

WIRE SIZE

0.8 0.9 1.0 1.2

95 16 12 22

---

17 13 18

--- --- --- 23

66 --- --- --62 30 32 42

64 --- --- ---

--- --- --- 48

More Deposition

Shorter Arc

STEEL 1.0mm

Pulse ArMix

Longer Arc

VOLTS

TRIM

0.0

EFFECT

Preflow Time

0 to 10 Seconds

RUN-IN WFS: OFF, 0.76 to 3.81m/mm

Start Procedure

START OPTIONS

DESCRIPTION

Adjusts the time that shielding gas

pulled

after

flows

prior to feeding wire.

and

the trigger

Run-in sets the wire feed speed from the time the trigger is pulled until an arc is established. The Start Procedure controls the WFS, Trim at a specified time at the beginning of the weld. During the start time, the machine will ramp up or down from the Start Procedure to the preset Welding Procedure.

EFFECT / RANGE

ARC FOCUS

-10.0 (SOFT to

10.0 (STIFF)

UltimArc™ Control

DESCRIPTION

Arc Focus adjusts the arc from a wide, soft arc good for out of position work to a narrow, stiff arc preferred for faster travel speeds. The pulse frequency is lower with a soft arc and higher with a stiff arc.

EFFECT

Spot Timer

0 to 120.0 Seconds

Crater Procedure

Burnback: 0 to 0.25 Seconds

Postflow Time 0 to 10 Seconds

END OPTIONS

FUNCTION

Adjust the time welding will continue even if the trigger is still pulled. This option has no effect in 4-Step Trigger Mode.

Adjusts the time that shielding

gas flows after the welding out-

put turns off.

POWER WAVE® C300 CE

Page 34

B-14

OPERATION

B-14

ALUMINUM SYNERGIC GMAW-P (PULSED MIG)AND GMAW-PP (PULSE ON PULSE) WELDING

The POWER WAVE® C300 CE can produce top quality aluminum welds with excellent appearance, little spatter and good bead shape. Push-pull guns are available for consistent feeding when welding a long distance away from the wire feeder.

PULSE-ON-PULSE WELDING

The Power Wave system offers both traditional pulse and Pulse-on-Pulse™. Pulse-on-Pulse (GMAW-PP) is an exclusive waveform for aluminum welding. Use it to make welds with a "stacked dime" appearance, similar to GTAW welds.( See Figure B.7)

FIGURE B.7

ALUMINUM GMAW-P AND GMAW-PP

ALUMINUM PULSE WELDING

Synergic GMAW-P (Pulsed MIG) welding is ideal for low spatter, out of position and reduced heat input applications. During pulse welding, the welding current continuously switches from a low level to a high level and then back again. Each pulse sends a small droplet of molten metal from the wire to the weld puddle.

Pulse welding controls the arc length with 'Trim' instead of voltage. When trim (arc length) is adjusted, the Power Wave automatically recalculates the voltage, current and time of each part of the pulse waveform for the best result. Trim adjusts the arc length and ranges from 0.50 to 1.50, with a nominal value of

1.00 for a 3/4" (19mm) electrode stick-out. Trim values greater than 1.00 increase the arc length, while values less than 1.00 decrease the arc length. (See Figure B.10)

FIGURE B.10

The pulsing frequency is adjustable. Changing the frequency modulation (or arc control) of the waveform changes the ripple spacing. Faster travel speeds may be achieved by using higher values of frequency modulation. ( See Figure B.8 and B.9p)

FIGURE B.8

Frequency Modulation = -10

Wide weld and ripple spacing, slow travel speed.

FIGURE B.9

Trim .50

Arc Length Short

Trim 1.00

Arc Length Medium

Trim 1.50

Arc L ength Long

Frequency Modulation = 10

Narrow weld and ripple spacing, fast travel speed.

POWER WAVE® C300 CE

Page 35

B-15

OPERATION

ALUMINUM GMAW-P (PULSED MIG) AND GMAW-PP (PULSE ON PULSE) WELDING

BASIC OPERATION

B-15

WELD MODES

ELECTRODE AND GAS

ALUMINUM 4043 Pulse ALUMINUM 4043 Pulse -on-Pulse Ar ALUMINUM 5356

ALUMINUM 5356 Pulse -on-Pulse Ar

WFS

AMPS

Less Deposition

1.0 1.2

4.5

More Deposition

Shorter Arc

CONTROL OPTIONS

WIRE SIZE

--- 72

--- 99 76 152 101 102

Aluminum 1.2mm

Pulse 4043 Ar

0.0

VOLTS

TRIM

Longer Arc

START OPTIONS

EFFECT

Preflow Time

0 to 10 Seconds

RUN-IN WFS:

OFF, 0.76 to 3.81m/mm

Start Procedure

DESCRIPTION

Adjusts the time that shielding

gas

flows

pulled

and

Run- in sets the wire feed speed from the time the trigger is pulled until an arc is estab- lished.

The Start Procedure controls the WFS. Trim at a specified time at the beginning of the weld. During the start time, the machine will ramp up or down

from the Start Procedure to the preset Welding Procedure.

the trigger is

after

prior to feeding wire.

EFFECT / RANGE

UltimArc™ Control

PULSE

FREQUENCY: (Low)-10.0 to (High)+10.0

PULSE-ON-PULSE

FREQ.MODULATION

(Low)-10.0 to (High)+10.0

DESCRIPTION

For Pulse changes the pulsing frequency. When the frequency changes,

the Power Wave system automa tically adju st s the background current to mainta in a similar heat input into the weld. Low frequencies give more control over the puddle and high

frequencies minimize spatter. For Pulse -On-Pulse modes,

Arc controls changes the frequency modulation. The freque-

-ncy modulation controls the spacing of the ripples in the weld. Use low values for slow travel speeds and wide welds, and high values for fast travel speeds and narrower welds.

modes, Arc Control

EFFECT

END OPTIONS

Spot Timer

0 to 120.0 Seconds

Crater Procedure

Burnback:

0 to 0.25 Seconds

Postflow Time

0 to 10 Seconds

FUNCTION

Adju st the time we lding will continue e ven i f the trigger is still pu lled. This op tion has no effect in 4-Step Trigger Mode.

Crater Procedure controls the WFS and Volts for a specified time at the end of the wel d after the trigger is released. During the Cr ater time, the machine will ramp up or down from the Weld Procedure to

the Crater Procedure.

The burnbac k time i s the amount of time that the weld output continues after the wire

stops feeding. It prevents the wire from sticking in the puddle and prepares the end of the wire for the next arc start.

Adjusts the time that shielding

gas flows after the welding out-

put turns off.

POWER WAVE® C300 CE

Page 36

B-16

OPERATION

GTAW (TIG) WELDING

The POWER WAVE® C300 CE is excellent for (Touch Start TIG) welding.

BASIC OPERATION

B-16

WFS

AMPS

WELD MODE

MODE

TOUCH START 3

UltimArc™ Control

No UltimArc™ Control are active for Touch Start TIG.

CONTROL OPTIONS

TOUCH START TIG

OUTPUT ON

OFF

The Start Procedure controls the Amperage at a fixed level for the set amount of time.

No Arc starting Options are active for Touch Start TIG

VOLTS

TRIM

OUTPUT OFF

START OPTIONS

END OPTIONS

WELD MODE SEARCHING

The Weld Mode Search feature allows the selection of a welding mode based on certain criteria (wire size, process type, etc.).

SEARCHING FOR A WELD MODE

To search for a mode, turn the control knob until “Weld Mode Search” is displayed. This will appear in between the highest and the lowest weld mode numbers.

Once “Weld Mode Search” is displayed, pressing the right pushbutton labeled “Begin” will start the search process.

POWER WAVE® C300 CE

During the search process, pressing the right pushbutton typically acts as a “next” button and the left pushbutton typically acts as a “back” button.

Rotate the control knob then press the right pushbutton to select relevant welding details such as welding process, wire type, wire size, etc.

When the final selection is made, the C300

will automatically change to the weld mode found by the Weld Mode Search process.

Earlier products may not have this feature. To activate this feature, a software update may be needed from www.powerwavesoftware.com

Page 37

B-17

OPERATION

B-17

SAVING A MEMORY:

To save the current machine settings to the selected memory, press and hold the center knob for (2 sec- onds). After two seconds, the alphanumeric displays will show “Memory # Save Memory” at which time the center knob should be released. After saving to a memory, a message will briefly appear indicating that the selected memory has been saved.

1. Press the Left Push Button until Memory 'M' LED is illuminated.

4T CO2

1.2mm

Steel

“M Led”

Job1

+ +

20.0

4.50

“M Led”

4.50

20.0

Job1

Steel CV

1.2mm CO2

RECALLING A MEMORY

To recall the selected memory, press and hold center knob for (1 second). After recalling a memory, a

message will briefly appear indicating that the selected memory has been recalled. The Memory LED will remain lit so that the user can quickly recall a different memory if needed.

1. Press the Left Push Button until Memory 'M' LED is illuminated.

4T CO2

1.2mm

Steel

“M Led”

Job1

+ +

15.5

5.00

“M Led”

5.00

15.5

Job1

Steel CV

1.2mm CO2

2. Rotate center knob to cycle to desired memory

2. Rotate center knob to cycle to desired memory location.

4T Ar Mix

Pulse

1.0mm

Stainless

Job4

20.0 4.50

Job4

Stainless Pulse

3. Press and hold center knob for 2 seconds. The active

procedure will be saved into the selected memory.

2 Seconds to save Memory” “Press and Hold Knob

Recalled Memory 4

20.0

4.50

Memory 4 Recalled

1.0mm Ar Mix

20.0

3. Press and hold center knob for 1 second. The

location.

4T Ar Mix

Pulse

1.0mm

Stainless

Job4

+ +

20.0 4.50

Job4

Stainless Pulse

selected memory is now active.

1 second. Memory is active. Press and Hold Knob for

Recalled Memory 4

+ +

20.0

4.50

Memory 4 Recalled

1.0mm Ar Mix

20.0

Press

“Press and Hold Knob 2 Seconds to save Memory”

2 SECONDS

POWER WAVE® C300 CE

Press and Hold Knob for 1 second. Memory is active.

1 SECOND

Press

Page 38

B-18

OPERATION

LIMITS

Limits allow the welder to adjust the welding procedure only within a defined range.

Each user memory may have a different set of limits. For example, memory 1 can be set to limit the WFS to 200 through 300 in/min, and memory 2 can be set to limit the WFS to 275 through 310 in/min, while memory 3 may not have any WFS limits.

Parameters are always constrained by machine limits. When memory limits are enabled, the parameter will flash whenever an attempt is made to exceed the memory limit value. The parameter will not flash if an attempt is made to exceed the machine limit.

B-18

Press the Left Push Button until Memory 'M' LED is illuminated.

Ar Mix

1.2mm

Steel

“M Led”

Job1

+ +

“M Led”

Job1

Steel CV

1.2mm Ar Mix

The system machine limits are:

Parameter

Wire Feed Speed

Voltage

Trim

UltimArc™Control

Preflow

Start Time

Run-In WFS

Crater Time

Burnback Time

Postflow Time

Range

Weld mode and wire

feeder dependent.

Weld mode dependent

0.50 to 1.50

-10.0 to 10.0

0.0 to 2.5

0.0 to 10.0

Off, 50 to 150

0.0 to 10.0

0.00 to 0.25

0.0 to 10.0

Limits may be set for:

• Wire Feed Speed/Amperage

• Voltage/Trim

• UltimArcTM Control

Units

in/min

Volts

Weld mode dependent

Seconds

in/min

Seconds

Rotate center knob to cycle to desired memory.

4T Ar Mix

Pulse

1.0mm

Stainless

Job4

+ +

Job4

Stainless Pulse

Press and hold center knob for 5 seconds. The Set Limits Menu will be active.

5 second. Limits is active. Press and Hold Knob for

Set Limits Memory 4

1.0mm Ar Mix

Weld modes cannot be selected through the Limits Setup menu, and must be chosen and saved to memory before entering the Limits Setup Menu.

POWER WAVE® C300 CE

Memory 4 Set Limits

PRESS

Press and Hold Knob for 5 second. Limits is active.

5 SECONDS

Page 39

B-19

OPERATION

B-19

1. Rotate center knob to select parameter to be set (WFS, Voltage, Trim).

Weld WFS Low 0.76 Hi=21.99

5.00

+ +

5.00

Hi=21.99

Weld WFS

2. Press the Left pushbutton to select the limit to be set (High, Nominal, Low). The selected value will blink.

4T Weld WFS Low 8.00 Hi=10.00

“M Led”

8.00

+ +

Low 0.76

4. Press the left push button to confirm changes (or press the right push button to cancel).

Confirm

√

Cancel

4T Saved Memory 4 limits

“M Led”

+ +

“M Led”

Memory 4 limits

√

Confirm

Saved

Cancel

WELD MODE SEARCH

The Weld Mode search function allows for a particular mode to be selected based on the process, wire type and wire size.

1. Press the Left Push Button until Weld Mode LED is illuminated.

Weld Mode

STD Cv Gas Shld

+ +

20.0

4.50

Hi=10.00

8.00

Weld WFS

Low 8.00

“M Led”

3. Once all limits have been set, press and hold for 1 second, release the center knob to accept. changes.

1 second. Accepts changes. Press and Hold Knob for

Yes Limits? Save

+ +

Save

Yes

Limits?

Press and Hold Knob for 1 second. Accepts changes.

1 SECOND

Press

4.50

20.0

Gas Shld

Weld Mode

2. Press and hold the center knob for 1 second release center knob. The Weld Mode search menu will be active.

1 second. Weld Mode is active. Press and Hold Knob for

Pulse MIG GMAW-P Select Process

Select Process Pulse MIG GMAW-P

STD Cv

Press and Hold Knob for 1 second. Weld Mode is active.

POWER WAVE® C300 CE

1 SECOND

Press

Page 40

B-20

OPERATION

B-20

3. Rotate center knob to cycle to desired process.

4T Power Mode Select Process

+ +

Select Process Power Mode

4. Press the right Push Button to select the process. If necessary, repeat steps 3 and 4 to select wire type, wire size, and final selection.

Power Mode

15.5

5.00

15.5

2-STEP 4-STEP- TRIGGER OPERATION

The 2-Step - 4-Step switch changes the function of the gun trigger. 2-Step trigger operation switches the welding output ON-OFF in direct response to the trigger. 4-Step trigger operation provides 'trigger interlock' capability and gives the ability to control the amount of time spent in the arc start and arc crater steps.

Press the right push button on the case front to toggle between 2-Step and 4-Step operation.

The 2-Step, 4-Step trigger has no effect when weld- ing with SMAW.

2-Step Trigger 2-Step trigger operation is the most common. When

the gun trigger is pulled, the welding system (power

Power Mode

source and wire feeder) cycles through the arc starting sequence and into the main welding parameters. The welding system will continue to weld as long as the gun trigger is activated. Once the trigger is released, the welding system cycles through the arc ending steps

4-Step Trigger 4-Step trigger operation gives the welder additional

control in the welding sequence. 4-Step trigger allows the welder to choose the arc start, weld and arc end time. It may also be set-up to work as a trigger interlock.

POWER WAVE® C300 CE

Page 41

B-21

OPERATION

EXAMPLE 1 - 2 STEP TRIGGER: Simple operation

The simplest trigger operation occurs with a 2 Step trigger and the Start, Crater and Burnback functions all set to OFF. (See Figure B.11)

For this sequence,

PREFLOW:

Shielding gas begins to flow immediately when the gun trigger is pulled.

RUN-IN:

After preflow time expires, the power source regulates to the welding output and wire is advanced towards the work piece at the Run-In WFS. If an arc is not established within 1.5 seconds, the wire feed speed will jump to the welding wire feed speed

WELD:

The power source output and the wire feed speed continue at the weld settings for as long as the trigger is pulled.

POSTFLOW: As soon as the trigger is released, the power source output and the wire feed speed are turned OFF. Shielding gas continues until the post flow timer expires.

B-21

Off Run-in

WFS

Weld

Off

Output

1.5 sec max.

Source Power

Weld

Off

Gas Shielding

IdlePreflowRun-InWeld PostflowIdle

Arc Trigger

Trigger

Established

Released

Pulled

Burnback = OFF Crater = OFF Start = OFF 2 Step Trigger

Shie lding Gas

Powe r Source Output

Off

Wel d

Off

Wel d

Pulled

Trigger

Idle Prefl ow

Run-In

1.5 sec max.

FIGURE B.11

2 Step Trigger Start = OFF Crater = OFF Burnback = OFF

Established

Arc

Released

Trigger

Weld Postflow Idle

WFS

Run-in

Off

POWER WAVE® C300 CE

Page 42

B-22

OPERATION

B-22

EXAMPLE 2 - 2 STEP TRIGGER: Improved Arc Start

and Arc End. Tailoring the arc start and arc end is a common method for reducing spatter and improving weld quality. This can be accomplished with the Start and Burnback functions set to a desired values and Crater set to OFF. (See Figure B.12)

For this sequence,

PREFLOW:

Shielding gas begins to flow immediately when the gun trigger is pulled.

RUN-IN:

After preflow time expires, the power source regulates to the start output and wire is advanced towards the work piece at the Run-In WFS. If an arc is not established within 1.5 seconds, the power source output and wire feed speed skips to the weld settings.

FIGURE B.12

2 Step Trigger Start = ON

Crater = OFF Burnback = ON

UPSLOPE:

Once the wire touches the work and an arc is established, both the machine output and the wire feed speed ramp to the weld settings throughout the start time. The time period of ramping from the start settings to the weld settings is called UPSLOPE.

WELD:

After upslope, the power source output and the wire feed speed continue at the weld settings.

BURNBACK: As soon as the trigger is released, the wire feed speed is turned OFF and the machine output continues for the burnback time.

POSTFLOW:

Next, the machine output is turned OFF and shielding gas continues until the post flow timer expires.

Shieldi n Gas

Pow er Source

Output

WFS

Run-in

OCV

Weld

Sta rt

Weld

Off

Pulled

Trigger

Idle Preflow

Run-In

1.5 s ec max.

Released

Established

Arc

Upslope Weld Burnback Postflow Idle

Start

time

Trigger

Burnback Time

POWER WAVE® C300 CE

Page 43

B-23

OPERATION

EXAMPLE 3 - 2 STEP TRIGGER: Customized Arc

Start, Crater and Arc End. Sometimes it is advantageous to set specific arc start, crater and arc ending parameters for the ideal weld. Many times when welding aluminum crater control is necessary to make a good weld. This is done by setting Start, Crater and Burnback functions to desired values. (See Figure B.13)

For this sequence,

PREFLOW:

Shielding gas begins to flow immediately when the gun trigger is pulled.

RUN-IN:

START & UPSLOPE:

As soon as the trigger is pulled, this starts preflow. The Strike arc established, Start time, and Upslope parameters are used at the beginning of the weld sequence to establish a stable arc and provide a smooth transition to the weld settings.

B-23

WELD:

After upslope, the power source output and the wire feed speed continue at the weld settings.

CRATER & DOWNSLOPE:

As soon as the trigger is released, the wire feed speed and power source output ramp to the crater settings throughout the crater time. The time period of ramping from the weld settings to the crater settings is called DOWNSLOPE.

BURNBACK:

After the crater time expires, the wire feed speed is turned OFF and the machine output continues for the burnback time.

POSTFLOW:

Next, the machine output is turned OFF and shielding gas continues until the post flow timer expires.

Shielding Gas

Power Source

Output

Off

Weld

Start

Crater

Off

Weld

FIGURE B.13

2 Step Trigger Start = ON

Crat er = ON Burnback = ON

Trigger Pulled

Idle Pref low Stri ke U pslo pe Weld Bu rnba ck Pos tf low Idle

1.5 sec max.

Arc Established

Start time

Trigger Released

Do wnslop e

Cr a ter ti m e

Burnback Time

WFS

Crat er Run -in

Off

POWER WAVE® C300 CE

Page 44

B-24

OPERATION

EXAMPLE 4 – 4 STEP TRIGGER: Trigger Interlock

The 4 step trigger can be configured as a trigger interlock. Trigger interlock adds to the welderʼs comfort when making long welds by allowing the trigger to be released after an initial trigger pull. Welding stops when the trigger is pulled a second time and then released, or if the arc is interrupted. (See Figure B.14)

For this sequence,

PREFLOW:

Shielding gas begins to flow immediately when the gun trigger is pulled.

RUN-IN:

WELD:

The power source output and the wire feed speed continue at the weld settings. Welding continues when the trigger is pulled a second time.

B-24

Shielding Gas

Power Source

Output

POSTFLOW:

As soon as the trigger is released for the second time, the power source output and the wire feed speed are turned OFF. Shielding gas flows until the post flow timer expires.

Pulled

Trigger

dle Preflow Strike Wel

Off

We l d

1. 5 s e c ma x .

Start

Crat er

Off

Established

Arc

FIGURE B.14

4 Step Trigge r Start = OFF Crater = OFF Burnback = OF F

Released

Trigger

Pulled

Trigger

Released

Trigger

Burnb ack Postflow Idle

WFS

We l d

Cra ter Ru n-in

Off

POWER WAVE® C300 CE

Page 45

B-25

OPERATION

EXAMPLE 5 - 4 STEP TRIGGER: Manual control of

Start and Crater times with Burnback ON. The 4 step trigger sequence gives the most flexibility when the Start, Crater and Burnback functions are active. This is a popular choice when welding aluminum because extra heat may be needed during Start and less heat desired during crater. With 4 step trigger, the welder chooses the amount of time to weld at the Start, Weld and Crater settings by using the gun trigger. Burnback reduces the occurrence of wire to sticking into the weld pool at the end of a weld and conditions the end of the wire for the next arc start. ( See Figure B.15)

In this sequence,

PREFLOW:

Shielding gas begins to flow immediately when the gun trigger is pulled.

RUN-IN:

After preflow time expires, the power source regulates to the start output and wire is advanced towards the work piece at the run-in WFS. If an arc is not established within 1.5 seconds, the power source output and wire feed speed skips to the weld settings.

START:

The power source welds at the start WFS and voltage until the trigger is released.

B-25

UPSLOPE:

During upslope, the power source output and the wire feed speed ramp to the weld settings throughout the start time. The time period of ramping from the start settings to the weld settings is called UPSLOPE.

WELD:

After upslope, the power source output and the wire feed speed continue at the weld settings.

DOWNSLOPE:

As soon as the trigger is pulled, the wire feed speed and power source output ramp to the crater settings throughout the crater time. The time period of ramping from the weld settings to the crater settings is called DOWNSLOPE.

CRATER:

During CRATER, the power source continues to supply output at the crater WFS and voltage.

BURNBACK:

When the trigger is released, the wire feed speed is turned OFF and the machine output continues for the burnback time.

POSTFLOW:

Next, the machine output is turned OFF and shielding gas continues until the post flow timer expires.

Shielding Gas

Po we r So urce Out put

WFS

Wel d

Start

Crat er

Wel d

St a r t Crat er Strike

FIGURE B.15

4 St ep Trigger Start = ON

Crat er = ON Burnback = ON

Start

Released

Trigger

Pulled

Trigger

Down slope

Crat er

Pulled

Trigger

Idle Preflow Strike Upslope W eld Burnback Postflow Idle

Of f

1.5 sec max.

Of f

Established

Arc

Released

Trigger

Bur nb ack Time

POWER WAVE® C300 CE

Page 46

B-26

COLD FEED/GAS PURGE SWITCH

OPERATION

B-26

Cold Feed and Gas Purge are combined into a single spring centered toggle switch.

To activate Cold Feeding, hold the switch in the UP position. The wire drive will feed electrode but neither the power source nor the gas solenoid will be energized. Adjust the speed of cold feeding by rotating the WFS knob. Cold feeding, or "cold inching" the electrode is useful for threading the electrode through the gun.

Hold with toggle switch in the DOWN position to activate Gas Purge and let the shielding gas flow. The gas solenoid valve will energize but neither the power source output nor the drive motor will be turned on. The Gas Purge switch is useful for setting the proper flow rate of shielding gas. Flow meters should always be adjusted while the shielding gas is flowing.

COLD FEED

GAS PURGE

POWER WAVE® C300 CE

Page 47

B-27

OPERATION

B-27

SETUP MENU FEATURES

The Setup Menu gives access to the Setup Configuration. Stored in the setup configuration are user parameters that generally only need to be set at installation. The parameters are grouped as shown in the following table.

PARAMETER

P.1 through P.99 P.101 through P.199 P.501 through P.599

1. To access the set-up menu, press the Right and

2. After changing a parameter it is necessary to press

3. To exit the set-up menu at any time, press the

DEFINITION

Unsecured Parameters (always adjustable)

Diagnostic Parameters (always read only)

Secured Parameters (only accessible through a p.c. or palm application)

SET-UP FEATURES MENU

(See Figure B.16)

Left buttons of the Main Display panel simultane- ously. Note that the set-up menu cannot be accessed if the system is welding, or if there is a fault (The status LED is not solid green).

Change the value of the blinking parameter by rotating the SET knob.

the Right hand button to save the new setting. Pressing the Left button will cancel the change.

Right and Left buttons of the Main Display panel simultaneously. Alternately, 1 minute of inactivity will also exit the set-up menu.

FIGURE B.16 - SETUP MENU

SET Knob

button button Right Left

Mode Set-Up LED

Main Display Panel Mode Select

Mode Select

Main Display Panel

LED

Set-Up

Mode

Left

button

Right

button

SET Knob

POWER WAVE® C300 CE

Page 48

B-28

OPERATION

USER DEFINED PARAMETERS

Parameter Definition

Exit Setup Menu

P. 0

This option is used to exit the setup menu. When P.0 is displayed, press the Left Button to exit the setup menu.

P.1 Wire Feed Speed Units

This option selects which units to use for displaying wire feed speed. English = inches/minute wire feed speed units (default). Metric = meters/minute wire feed speed units.

P.2 Arc Display Mode

This option selects what value will be shown on the upper left display while welding. Amps = The left display shows Amperage while welding (default). WFS = The left display shows Wire Feed Speed while welding.

P.3 Display Options

This setup parameter was previously named "Display Energy"

B-28

If the previous software revision had this parameter set to display energy, that selection will remain.

This option selects the information displayed on the alphanumeric displayes while welding. Not all P.3 selections will be available on all machines. In order for each selection to be included in the list, the power source must support that feature. A software update of the power source may be needed to include the features.

Standard Display = The lower displays will continue to show preset information during and after a weld (default). Show Energy = Energy is displayed, along with time in HH:MM:SS format. Show Weld Score = The accumulative weld score result is shown.

P.4 Recall Memory with Trigger

This option allows a memory to be recalled by quickly pulling and releasing the gun trigger. To recall a memory, quickly pull and release the trigger the number of times that correspond to the memory number. For example, to recall memory 3, quickly pull and release the trigger 3 times. To recall memory 1, quickly pull and release the trigger the number of user memories plus 1. Memories cannot be recalled while the system is welding. Disabled = The gun trigger cannot be used to recall user memories (default). Enabled = The gun trigger can be used to recall user memories.

POWER WAVE® C300 CE

Page 49

B-29

OPERATION

USER DEFINED PARAMETERS

Parameter Definition

P.5 Procedure Change Method

Selects how remote procedure selection (A/B) will be made. The selected procedure can be changed locally at the user interface by pressing the 'A-Gun-B' button. The following methods can be used to remotely change the selected procedure:

• Use an external switch wired to the procedure select input.

• Quickly releasing and re-pulling the gun trigger.

• Using a dual-schedule gun which incorporates a procedure select switch in the trigger mechanism (pulling the trigger more than half way changes the procedure from A to B).

The possible values for this parameter are:

• External Switch = Procedure selection may only be performed at the memory panel or an external switch (e.g. K683).

• Quick Trigger = The selected procedure can be changed remotely by releasing and re-pulling the trigger quickly while welding. This feature is disabled in 4-Step trigger mode. The external procedure switch is disabled. To operate:

1. Select "GUN" on the memory panel.

2. Start the weld by pulling the gun trigger. The system will weld with procedure A settings.

3. While welding, quickly release then pull the gun trigger once. The system will switch to procedure B settings. Repeat to switch back to procedure A settings. The procedure can be changed as many times as needed during the weld.

4. Release the trigger to stop welding. The system will automatically return to procedure A settings.

B-29

• Integral TrigProc = When using a Magnum DS dual-schedule gun (or similar) that incorporates a procedure switch in the gun trigger mechanism. While welding in 2-step, machine operation is identical to the "External Switch" selection. When welding in 4-step, additional logic prevents procedure A from being re-selected when the trigger is released at step 2 of the 4-step weld sequence. The machine will always operate in 2-step if a weld is made exclusively in procedure A, regardless of the 2/4 step switch position (this is intended to simplify tack welding when using a dual-schedule gun in 4-step).

P.6 Stall Factor Adjustment

This option allows the adjustment of the stall factor in Push/Pull operation. The stall factor controls the stall torque of the push motor when using a push-pull gun. The wire feeder is factoryset to not stall unless there is a large resistance to feeding wire. The stall factor can be reduced to stall more easily and possibly prevent bird nesting. However, low stall factors can cause motor stalling during normal welding conditions, which results in the wire burning back to the tip or rapid tack welds. If you are experiencing bird nests, check for other feeding problems before adjusting the stall factor. The default value for the stall factor is 75, with a range of 5 to 100.

POWER WAVE® C300 CE

Page 50

B-30

OPERATION

USER DEFINED PARAMETERS

Parameter Definition

P.7 Gun Offset Adjustment

This option adjusts the wire feed speed calibration of the pull motor of a push-pull gun. This should only be performed when other possible corrections do not solve any push-pull feeding problems. An rpm meter is required to perform the pull gun motor offset calibration. To perform the calibration procedure do the following:

1. Release the pressure arm on both the pull and push wire drives.

2. Set the wire feed speed to 200 ipm.

3. Remove wire from the pull wire drive.

4. Hold an rpm meter to the drive roll in the pull gun.

5. Pull the trigger on the push-pull gun.

6. Measure the rpm of the pull motor. The rpm should be between 115 and 125 rpm. If necessary, decrease the calibration setting to slow the pull motor, or increase the calibration setting to speed up the motor.

The calibration range is -30 to +30, with 0 as the default value.

P.8 TIG Gas Control

This option allows control over which gas solenoid actuates while TIG welding. "Valve (manual)" = No MIG solenoid will actuate while TIG welding, gas flow is manually con trolled by an external valve. "Solenoid (auto) = This selection only applicable to PWC300. The MIG solenoid will turn on and off automatically while TIG welding. "Feeder Solenoid" = No applicable to PWC300. The internal (feeder) MIG solenoid will turn on and off automatically while TIG welding. "Pwr Src Solenoid" = Not applicable to PWC300. Any gas solenoid connected to the power source will turn on and off automatically while TIG welding. This selection will not appear in the list if the power source does not support a gas solenoid.

B-30

Notes: Preflow is not available while TIG welding. Postflow is available - the same postflow time will be used in MIG and TIG. When machine output on/off is controlled via the upper right knob, gas flow will not start until the tungsten touches the work. Gas flow will continue when the arc is broken until the Postflow time expires. When machine output on/off is controlled via an arc start switch or foot Amptrol, gas will begin flowing when the output is turned on and will continue flowing until the output is turned off and the Postflow time expires.

P.9 Crater Delay

This option is used to skip the Crater sequence when making short tack welds. If the trigger is released before the timer expires, Crater will be bypassed and the weld will end. If the trigger is released after the timer expires, the Crater sequence will function normally (if enabled).

P.14 Reset Consumable Weight

Use this option to reset the initial weight of the consumable package. Press the Right Button to reset the consumable weight. This option will only appear with systems using Production Monitoring.

POWER WAVE® C300 CE

Page 51

B-31

OPERATION

USER DEFINED PARAMETERS

Parameter Definition

P.16 Push-Pull Gun Knob Behavior

This option determines how the potentiometer on the Push/Pull torch will behave. Gun Pot Enabled = The welding wire feed speed is always controlled by the potentiometer on the pushpull gun (default). The left front panel knob is only used to adjust Start and Crater wire feed speed. Gun Pot Disabled = The wire feed speed is always controlled by the left front panel knob. This setting is useful when the operator wishes to have wire feed speed settings recalled from memories and not have the potentiometer "overwrite" the setting. Gun Pot Proc A = When in procedure A, the welding wire feed speed is controlled by the potentiometer on the push-pull gun. When in procedure B, the welding wire feed speed is controlled by the left front panel knob. This setting allows a fixed wire feed speed to be selected in procedure.

P.17 Remote Control Type

This setup parameter was previously named "Spool/Push-Pull".

This option selects the type of analog remote control being used. Digital remote control devices (those with a digital display) are configured automatically. Not all P.17 selections will be available on all machines. When P.17 is used to configure the remote control to function in a specific process, the remote will be ignored in other processes. For example, if P.17 = TIG Amp Control, the remote control will only function when TIG welding - the remote will be ignored in other processes (MIG, stick and gouge).

B-31

Spool Gun = Use this setting while MIG welding with a spool gun that uses a potentiometer used for wire feed speed control (this setting is backward compatible with "P.17 Gun Selection" = Standard/Spool).

Push-Pull Gun = Use this setting wile MIG welding with a push-pull gun that uses a potentiometer for wire feed speed control (this setting is backward compatible with "P.17 Gun Selection" = PushPull).

TIG Amp Control = Use this setting while TIG welding with a foot or hand current control device (Amptrol). While TIG welding, the upper left knob on the User Interface sets the maximum current obtained when the TIG amp control is at its maximum setting.

Stick/Gouge Rem. = Use this setting while stick welding or gouging with a remote output control device. While stick welding, the upper left knob on the User Interface sets the maximum current obtained when the stick remote is at itʼs maximum setting. While gouging, the upper left knob is disabled and the gouging current is set on the remote control.

All Mode Remote = This setting allows the remote control to function in all weld modes which is how most machines with 6-pin and 7-pin remote control connections operate. This setting was provided so that customers with a mix of Lincoln Electric equipment can have consistent remote control behavior across all of their equipment. (N. American default)

Joystick MIG Gun = Use this setting while MIG welding with a push MIG gun with a joystick control. Stick, TIG and gouge welding currents are set at the User Interface. (European default)

P.20 Display Trim as Volts Options

This option determines how trim is displayed. False = The trim is displayed in the format defined in the weld set (default). True = All trim values are displayed as a voltage.

POWER WAVE® C300 CE

Page 52

B-32

OPERATION

USER DEFINED PARAMETERS

Parameter Definition

P.22 Arc Start/Loss Error Time

This option can be used to optionally shut off output if an arc is not established, or is lost for a specified amount of time. Error 269 will be displayed if the machine times out. If the value is set to OFF, machine output will not be turned off if an arc is not established nor will output be turned off if an arc is lost. The trigger can be used to hot feed the wire (default). If a value is set, the machine output will shut off if an arc is not established within the specified amount of time after the trigger is pulled or if the trigger remains pulled after an arc is lost. This is disabled while welding in Stick, TIG or Gouge. To prevent nuisance errors, set Arc Start/Loss Error Time to an appropriate value after considering all welding parameters (run-in wire feed speed, weld wire feed speed, electrical stick out, etc). To prevent subsequent changes to Arc Start/Loss Error Time, the setup menu should be locked out by setting Preference Lock = Yes using the Power Wave Manager software.

P.80 Sense From Studs

Use this option for diagnostic purposes only. When power is cycled, this option is automatically reset to False. False = Voltage sensing is automatically determined by the selected weld mode and other machine settings (default). True = Voltage sensing is forced to "studs".

B-32

P.81 Sense Leads Selection

Used in place of DIP switches for configuration of the work and electrode sense leads. This option will only appear in the list if the power source has a hardware selection option. 67 pos polarity = An electrode sense lead is connected using positive polarity. This is used by most GMAW welding procedures. 67 neg polarity = An electrode sense lead is connected using negative polarity. This is used by most GTAW welding procedures and some Innershield procedures. 67 & 21 = An electrode sense lead and work sense lead are connected. Hardware Config = The hardware determines the best remote sensing configuration. This is applicable to MIG welding procedures only.

P.82 Voltage Sense Display

Allows viewing of Voltage Sense Lead Selection to aid in troubleshooting. The configuration is displayed as a text string on the lower display whenever the output is enabled. This parameter is not saved on a power cycle, but will be reset to False.

P.99 Show Test Modes?

Most power sources contain weld modes used for calibration and test purposes. By default, the machine does not include test weld modes in the list of weld modes that are available to the operator. To manually select a test weld mode, set this option to "Yes". When the power source is turned off and back on again, the test modes will no longer appear in the mode list. Test weld modes typically require the machine output to be connected to a grid load and cannot be used for welding.

P.100 View Diagnostic?

Diagnostics are only used for servicing or troubleshooting the Power Wave system. Select "Yes" to access the diagnostic options in the menu. Additional parameters will now appear in the setup menu (P.101, P.102, etc).

POWER WAVE® C300 CE

Page 53

B-33

OPERATION

USER DEFINED PARAMETERS

Parameter Definition

P.102 View Fatal Logs

Used for viewing all the system fatal logs. Press the Right Button to enter the option. Rotate Control Knob to select the desired fatal log to read. Press the Right Button again to enter that log. Rotating the Control Knob will scroll through the log, displaying the log index number and fatal code. Press the Left Button to back out to select another log. Press the Left Button again to exit this option.

P.103 View Software Version Information

Used for viewing the software versions for each board in the system. Press the Right Button to enter the option. Rotate Control Knob to select the desired board to read. Press the Right Button again to read the firmware version. Press the Left Button to back out to select another board. Rotate the Control Knob to select another board, or press the Left Button to exit this option.

P.104 View Hardware Version Information

Used for viewing the hardware version for each board in the system. Press the Right Button to enter the option. Rotate Control Knob to select the desired board to read. Press the Right Button again to read the hardware version. Press the Left Button to back out to select another board. Press the Left Button again to exit this option.

B-33

P.105 View Welding Software Information

Used for viewing the Weld Set in the Power Source. Press the Right Button to read the Weld Set version. Press the Left Button to back out and exit this option.

P.106 View Ethernet IP Address

Used for viewing the IP address of Ethernet compatible equipment. Press the Right Button to read the IP Address. Press the Left Button to back out and exit this option. The IP address cannot be changed using this option.

P.107 View Power Source Protocol

Used for viewing the type of power source the feeder is connected to. Press the Right Button to identify the power source as either LincNet or ArcLink. Press the Left Button to back out and exit this

P.501 Encoder Lockout

Locks one or both of the upper knobs (encoders), preventing the operator from changing wire feed speed, amps, volts or trim. The function of each upper knob depends on the selected weld mode. When a constant current weld mode is selected (e.g. Stick, TIG, Gouge), the upper right knob will always function as an on/off switch. This parameter can only be accessed using PowerWave

P.502 Memory Change Lockout

Determines if the memories can be overwritten with new contents. No = Memories can be saved and limits can be configured (default). Yes = Memories cannot be changed - saving is prohibited and limits cannot be re-configured. This parameter can only be accessed using Power Wave Manager software.

POWER WAVE® C300 CE

Page 54

B-34

OPERATION

USER DEFINED PARAMETERS

Parameter Definition

P.503 Memory Button Disable

Disables the specified memory button(s). When a memory is disabled, welding procedures cannot be restored from or saved to that memory. If an attempt is made to save or restore a disabled memory, a message will be displayed on the lower display indicating the memory number is disabled. In multi-head systems, this parameter disables the same memory buttons on both feed heads. This parameter can only be accessed using Power Wave Manager software.

P.504 Mode Select Panel Lock

Selects between several Mode Select Panel lockout preferences. When a Mode Select Panel selection is locked and an attempt is made to change that parameter, a message will be displayed on the lower display indicating the parameter is locked.

• All MSP Options Unlocked = All adjustable parameters on the Mode Select Panel are

unlocked.

• All MSP Options Locked = All knobs and buttons on the Mode Select Panel are locked.

• Start and End Options Locked = The Start and End parameters on the Mode Select Panel are

locked, all others are unlocked.

• Weld Mode Option Locked = The weld mode cannot be changed from the Mode Select Panel,

all others Mode Select Panel settings are unlocked.

• Wave Control Options Locked = The Wave Control parameters on the Mode Select Panel are

locked, all others are unlocked.

• Start, End, Wave Options Locked = The Start, End and Wave Control parameters on the

Mode Select Panel are locked, all others are unlocked.

• Start, End, Mode Options Locked = The Start, End and Weld Mode Select parameters on the

Mode Select Panel are locked, all others are unlocked.

• This parameter can only be accessed using Power Wave Manager software.

B-34

P.505 Setup Menu Lock

Determines if the setup parameters can be modified by the operator without entering a passcode. No = The operator can change any set menu parameter without first entering the passcode even if the passcode is non-zero (default). Yes = The operator must enter the passcode (if the passcode is non-zero) in order to change any setup menu parameters. This parameter can only be accessed using Power Wave Manager software.

P.506 Set User Interface Passcode

Prevents unauthorized changes to the equipment. The default passcode is zero which allows full access. A nonzero passcode will prevent unauthorized: changes to memory limits, saving to memory (if P.502 = Yes), changes to setup parameters (if P.505 = Yes). This parameter can only be accessed using Power Wave Manager software.

P.509 UI Master Lockout

Locks all user interface controls, preventing the operator from making any changes. This parameter can only be accessed using Power Wave Manager software.

POWER WAVE® C300 CE

Page 55

B-35

OPERATION

USER DEFINED PARAMETERS

Parameter Definition

P.507 UI Clear All Memories

Allows the operator to quickly set all memories to the default weld mode and welding parameters. Presently, this option does not exist in any setup menu.

P.509 UI Master Lockout

Locks all user interface controls, preventing the operator from making any changes. This parameter can only be accessed using Power Wave Manager.

B-35

POWER WAVE® C300 CE

Page 56

C-1

ACCESSORIES

C-1

OPTIONS / ACCESSORIES

K857 REMOTE OUTPUT CONTROL

Portable current control provides the same dial range as the current control on the welder. Consists of a 6-pin Amphenol connector which plugs into the remote control Amphenol. 25 foot cable length.

TIG OPTIONS

Lincoln Electric offers a full line of TIG Torches. Contact your local Lincoln

Electric sales office for more information.

K870 FOOT AMPTROL*

Depress pedal to increase current. Depressing pedal fully achieves maximum set current. Fully raising the pedal finishes the weld and starts the Afterflow cycle.

WIRE FEEDER OPTIONS

K2490-1 MAGNUM®250LX SPOOL GUN

Air-Cooled, 25 ft. 280 amps,60% duty cycle Feeds .025”-3/64” (0.6-1.2mm) diameter aluminum wire on 2lbs. (0.9kg.) spool.

The Magnum 250LX spool gun is a professional grade solution for feeding small spools of aluminum and steel wire.

K2519-1 CONTROL CABLE EXTENSION

Extend your spool gun reach with a 25 ft. (7.5 m) control cable extension. Features a 7-pin female MS-type connector on the spool gun end and a 7-pin male MS-type connector on the power source end.

PUSH PULL GUNS

K963-3 HAND AMPTROL*

Provides 25 ft (7.6m) of remote current control for TIG welding. (6-pin plug connection).

K814 ARC START SWITCH (25FT., 7.6m)*

CUT LENGTH CONSUMABLES

TIG welding filler metals are available for welding stainless steel, mild steel, aluminum and copper alloys.

* Requires K2909-1

12 pin - 6 pin Remote Adapter Cable

Lincoln Electric offers both the Cougar™ pistol grip and Panther™ gooseneck style push-pull guns for feeding aluminum wire. Both Air and Water cooled versions are available. Contact your local Lincoln Electric sales office for more information.

K1738-1 SPOOL GUN HOLDER

K2378-1 CANVAS COVER

K2734-1 POWER WAVE® C300 CE CART

WELD FUME EXTRACTORS

Lincoln Electricʼs® WELD FUME EXTRACTORS are portable, low vacuum/high volume self-cleaning filtration system designed for heavy duty extraction and filtration of welding fumes. Easily wheeled around the shop-wide central systems servicing many welding stations.

POWER WAVE® C300 CE

Page 57

D-1

MAINTENANCE

SAFETY PRECAUTIONS

WARNING

ELECTRIC SHOCK can kill.

•Do not operate with covers removed.

•Turn off power source before installing or servicing.

•Do not touch electrically hot parts.

• Turn the input power to the welding power source off at the fuse box before working in the terminal strip.

• Only qualified personnel should install, use or service this equipment.

------------------------------------------------------------------------

ROUTINE MAINTENANCE

Routine maintenance consists of periodically blowing out the machine, using a low-pressure air stream, to remove accumulated dust and dirt from the intake and outlet louvers, and the cooling channels in the machine.

D-1

PERIODIC MAINTENANCE

Calibration of the POWER WAVE® C300 CE is critical to its operation. Generally speaking the calibration will not need adjustment. However, neglected or improperly calibrated machines may not yield satisfactory weld performance. To ensure optimal performance, the calibration of output Voltage and Current should be checked yearly.

CALIBRATION SPECIFICATION

Output Voltage and Current are calibrated at the factory. Generally the machine calibration will not need adjustment. However, if the weld performance changes, or the yearly calibration check reveals a problem, use the calibration section of the Diagnostics Utility to make the appropriate adjustments.

The calibration procedure itself requires the use of a grid, and certified actual meters for voltage and current. The accuracy of the calibration will be directly affected by the accuracy of the measuring equipment you use. The Diagnostics Utility includes detailed instructions, and is available on the Service

Navigator CD or at www.powerwavesoftware.com.

POWER WAVE® C300 CE

Page 58

E-1

TROUBLESHOOTING

HOW TO USE TROUBLESHOOTING GUIDE

WARNING

Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel. Unauthorized repairs performed on this equipment may result in danger to the technician and machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical Shock, please observe all safety notes and precautions detailed throughout this manual.

__________________________________________________________________________

E-1

This Troubleshooting Guide is provided to help you locate and repair possible machine malfunctions. Simply follow the three-step procedure listed below.

Step 1. LOCATE PROBLEM (SYMPTOM).

Look under the column labeled “PROBLEM (SYMPTOMS)”. This column describes possible symptoms that the machine may exhibit. Find the listing that best describes the symptom that the machine is exhibiting.

Step 2. POSSIBLE CAUSE.

The second column labeled “POSSIBLE CAUSE” lists the obvious external possibilities that may contribute to the machine symptom.

Step 3. RECOMMENDED COURSE OF ACTION

This column provides a course of action for the Possible Cause, generally it states to contact your local Lincoln Authorized Field Service Facility.

If you do not understand or are unable to perform the Recommended Course of Action safely, contact your local Lincoln Authorized Field Service Facility.

WARNING

ELECTRIC SHOCK can kill.

• Turn the input power OFF at the welding power source before installation or changing drive rolls and/or guides.

• Do not touch electrically live parts.

• When inching with the gun trigger, electrode and drive mechanism are "hot" to work and ground and could remain energized several seconds after the gun trigger is released.

• Welding power source must be connected to system ground per the National Electrical Code or any applicable local codes.

• Only qualified personnel should perform maintenance work.

Observe all additional Safety Guidelines detailed throughout this manual.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER WAVE® C300 CE

Page 59

E-2

TROUBLESHOOTING

USING THE STATUS LED TO TROUBLESHOOT SYSTEM PROBLEMS

Not all of the Power Wave C300 CE errors will be displayed on the user interface. There are three status lights that contain error sequences that may not show up on the user interface. If a problem occurs it is important to note the condition of the status lights. Therefore, prior to cycling power to

the system, check the power source status light for error sequences as noted below.

There are two status lights located above the wire drive in the wire feeder compartment. One of the status lights is for the main control board ( labeled “status”, and one for the wire drive module. The third status light is internal and is located on the input control board.

TABLE E.1

Light

Condition

Main control board status light and Wiredrive Status Light

E-2

There is an audible beeper associated with this input control boardʼs status light. So the error codes on the input board can be detected through either the status light or the status beeper.

Included in this section is information about the Status Lights and some basic troubleshooting charts for both machine and weld performance.

The status lights on the main control board and the wire drive module are dual-color LEDʼs. Normal operation for each is steady green. Where as the status light on the input control board is one color. Normal operation is for the status light to be off ( and the buzzer to be off).

Error conditions are indicated in the following Table E.1.

Meaning

Input control board

Steady Green

Blinking Green

Fast Blinking Green

Alternating Green and Red

Steady Red

Blinking Red

System OK. Power source is operational, and is communicating normally with all

healthy peripheral equipment connected to its ArcLink network.

Occurs during power up or a system reset, and indicates the POWER

WAVE® C300 CE is mapping (identifying) each component in the sys-

tem. Normal for first 1-10 seconds after power is turned on, or if the

system configuration is changed during operation.

Indicates Auto-mapping has failed

Non-recoverable system fault. If the Status lights are flashing any combination of red and green, errors are present. Read the error code(s)

before the machine is turned off.

Error Code interpretation through the Status light is detailed in the

Service Manual. Individual code digits are flashed in red with a long

pause between digits. If more than one code is present, the codes will

be separated by a green light. Only active error conditions will be

accessible through the Status Light.

Error codes can also be retrieved with the Diagnostics Utility (includ-

ed on the Service Navigator CD or available at www.power-

wavesoftware.com). This is the preferred method, since it can access

historical information contained in the error logs.

To clear the active error(s), turn power source off, and back on to

reset.

Not applicable.

Error Code interpretation -

Individual code digits are flashed in red with a long pause between digits. These error codes are three digit codes that all start with a number three.

Status LED off

Not applicable.

System OK

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER WAVE® C300 CE

Page 60

E-3

TROUBLESHOOTING

Observe all Safety Guidelines detailed throughout this manual

E-3

ERROR CODES FOR THE POWER WAVE®

The following is a partial list of possible error codes for the POWER WAVE® C300 CE. For a complete listing consult the Service Manual for this machine.

MAIN CONTROL BOARD ( “STATUS” LIGHT)

Error Code #

Indication

36 Thermal error

54 Secondary (Output) over current error

56 Chopper communication error

58 Primary Fault error

Other

WIRE DRIVE MODULE

81 Motor Overload

Indicates over temperature. Usually accompanied by Thermal LED. Check fan operation. Be sure process does not exceed duty cycle limit of the machine

The long term average secondary (weld) current limit has been exceeded. NOTE: The long term average secondary current limit is 325 amps.

Indicates communication link between main control board and chopper has errors. If cycling the input power on the machine does not clear the error, contact the Service Department.

Review error code from input board status light or status beeper. Most likely caused by an over power condition which caused an under voltage on the primary bus. If cycling the input power on the machine does not clear the error, contact the Service Department.

Error codes that contain three or four digits are defined as fatal errors. These codes generally indicate internal errors on the Power Source Control Board. If cycling the input power on the machine does not clear the error, contact the Service Department.

Long term average motor current limit has been exceeded. Typically indicates mechanical overload of system. If problem continues consider higher torque gear ratio (lower speed range).

82 Motor Overcurrent

Absolute maximum motor current level has been exceeded. This is a short term average to protect drive circuitry.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER WAVE® C300 CE

Page 61

E-4

Error Code #

TROUBLESHOOTING

Observe all Safety Guidelines detailed throughout this manual

INPUT CONTROL BOARD

Indication

E-4

331 Peak input current limit

333 Under-voltage lockout

336 Thermal Fault

337 Pre-charge timeout

346 Transformer primary over current

Other

Input current limit has been exceeded. Typically indicates short term power overload. If problem persists contact Service Department.

+15 VDC supply on Input control board too low. Verify input voltage is within the acceptable range. If problem persists contact service department.

Thermostat on primary module tripped. Typically caused by bottom fan not working.

Problem with start-up sequence. If problem persists contact Service Department.

Transformer current too high. Typically indicates short term power overload. If problem persists contact service department.

Contact the Service Department.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER WAVE® C300 CE

Page 62

E-5

Observe all Safety Guidelines detailed throughout this manual

PROBLEMS

(SYMPTOMS)

TROUBLESHOOTING

POSSIBLE

CAUSE

Basic Machine Problems

E-5

RECOMMENDED

COURSE OF ACTION

Input fuses keep blowing

Machine will not power up (no lights)

1. Improperly sized input fuses.

2. Improper Weld Procedure requiring output levels in excess of machine rating.

3. Major physical or electrical damage is evident when the covers are removed.

1. No Input Power

2. Input voltage is too low or too high.

1. Make sure fuses are properly sized. See installation section of this manual for recommended sizes.

2. Reduce output current, duty cycle, or both.

3. Contact your local authorized Lincoln Electric Field Service facility for technical assistance.

1. Make sure input supply disconnect has been turned ON. Check input fuses. Make certain that the Power Switch (SW1) on the power source is in the “ON” position.

2. Make certain that input voltage is correct, according to the Rating Plate located on the rear of the machine.

Machine wonʼt weld, canʼt get any output.

This problem will normally be accompanied by an error code. See “Status Light” section of this document for additional information.

Input voltage is too low or too high.

2. Thermal Error.

3. Secondary current limit has been exceeded. (see error 54)

3a. Input control board fault (see

input control board error status).

1. Make certain that input voltage is correct, according to the Rating Plate located on the rear of the machine.

2. See “Thermal LED is ON” sec- tion.

3. Possible short in output circuit. If condition persists, contact an authorized Lincoln Electric Field Service facility.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER WAVE® C300 CE

Page 63

E-6

PROBLEMS

(SYMPTOMS)

TROUBLESHOOTING

Observe all Safety Guidelines detailed throughout this manual

POSSIBLE

CAUSE

RECOMMENDED

COURSE OF ACTION

E-6

Thermal LED is ON

“Real Time Clock” no longer functioning

General degradation of weld performance

Improper fan operation

Basic Machine Problems (Continued)

1. Improper fan operation.

2. Open thermostat circuit.

1. Control PC Board Battery.

Weld and Arc Quality Problems

1. Wire feed problem.

2. Cabling problems.

1. Check for proper fan operation. Fan should run in a low speed setting when the machine is idle and in a high speed when the output is triggered. Check for material blocking intake or exhaust louvers, or for excessive dirt clogging cooling channels in machine.

2. Check for broken wires, open connections or faulty thermostats in the thermostat circuit.

1. Replace the battery (Type: BS2032)

1. Check for feeding problems. Make sure proper gear ratio has been selected.

2. Check for bad connections, excessive loops in cable, etc.

3. Loss of, or improper Shielding Gas.

4. Verify weld mode is correct for process.

5. Machine calibration.

6. Wire feed problem.

NOTE: The presence of heat in the external welding circuit indicates poor connections or undersized cables.

3. Verify gas flow and type are correct.

4.Select the correct weld mode for

the application.

5. The power source may require calibration. (current, voltage, WFS).

6. Check for feeding problems. Make sure proper gear ratio has been selected.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER WAVE® C300 CE

Page 64

E-7

Observe all Safety Guidelines detailed throughout this manual

PROBLEMS

(SYMPTOMS)

Weld and Arc Quality Problems (Continued)

Wire burns back to tip at the end of the weld.

TROUBLESHOOTING

POSSIBLE

CAUSE

1. Burnback Time

E-7

RECOMMENDED

COURSE OF ACTION

1. Reduce burnback time and/or work point.

Machine output shuts down during a weld.

Machine wonʼt produce full output.

Excessively long and erratic arc.

1. Secondary current limit has been exceeded, and the machine shuts down to protect itself.

2. System Fault

1. Input voltage may be too low, limiting output capability of the power source.

2. Machine calibration.

1. Wire feed problem.

2. Loss of, or improper Shielding Gas

1. Adjust procedure or reduce load to lower current draw from the machine.

2. A non-recoverable fault will interrupt welding. This condition will also result in a status light blinking. See the Status Light section for more information.

1. Make certain that the input voltage is proper, according to the Rating Plate located on the rear of the machine.

2. Calibrate secondary current and voltage.

1. Check for feeding problems. Make sure proper gear ratio has been selected.

2. Verify gas flow and type are correct

3. Machine calibration.

3. Calibrate secondary current and voltage.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER WAVE® C300 CE

Page 65

E-8

PROBLEMS

(SYMPTOMS)

TROUBLESHOOTING

Observe all Safety Guidelines detailed throughout this manual

POSSIBLE

CAUSE

Ethernet

RECOMMENDED

COURSE OF ACTION

E-8

Cannot Connect

1. Physical connection.

2. IP address information.

3. Ethernet Speed

1. Verify that the correct patch cable or cross over cable is being used (refer to local IT department for assistance).

1a. Verify the cables are fully insert-

ed into the bulk head connector.

1b. Th e LED under the PC board

ethernet connector will be lit when the machine is connected to another network device.

2. Use the appropriate PC utility to verify the correct IP address information has been entered.

2a. Verify no duplicate the IP

addresses exist on the network.

3. Verify that the network device connected to the Power Wave is either a 10-baseT device or a 10/100-baseT device.

Connection Drops while welding

1. Cable Location

1. Verify Network cable is not located next to current carrying conductors. This would include input power cables and welding output cables.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER WAVE® C300 CE

Page 66

F-1

Enhanced Diagram

WIRING DIAGRAM

F-1

POWER WAVE® C300 CE

NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the

machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number.

Page 67

F-2

DIMENSION PRINT

F-2

POWER WAVE® C300 CE

Page 68

NOTES

POWER WAVE® C300

Page 69

NOTES

POWER WAVE® C300

Page 70

WARNING

Spanish

AVISO DE

PRECAUCION

G Do not touch electrically live parts or

electrode with skin or wet clothing.

G Insulate yourself from work and

ground.

G No toque las partes o los electrodos

bajo carga con la piel o ropa mojada.

G Aislese del trabajo y de la tierra.

G Keep flammable materials away.

G Mantenga el material combustible

fuera del área de trabajo.

G Wear eye, ear and body protection.

G Protéjase los ojos, los oídos y el

cuerpo.

French

ATTENTION

German

WARNUNG

Portuguese

ATENÇÃO

Japanese

Chinese

Korean

Arabic

G Ne laissez ni la peau ni des vête-

ments mouillés entrer en contact avec des pièces sous tension.

G Isolez-vous du travail et de la terre.

G Berühren Sie keine stromführenden

Teile oder Elektroden mit Ihrem Körper oder feuchter Kleidung!

G Isolieren Sie sich von den

Elektroden und dem Erdboden!

G Não toque partes elétricas e elec-

trodos com a pele ou roupa molhada.

G Isole-se da peça e terra.

G Gardez à l’écart de tout matériel

inflammable.

G Entfernen Sie brennbarres Material!

G Mantenha inflamáveis bem guarda-

dos.

G Protégez vos yeux, vos oreilles et

votre corps.

G Tragen Sie Augen-, Ohren- und Kör-

perschutz!

G Use proteção para a vista, ouvido e

corpo.

READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.

SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.

LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.

LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HERSTELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.

Page 71

G Keep your head out of fumes. G Use ventilation or exhaust to

remove fumes from breathing zone.

G Turn power off before servicing.

G Do not operate with panel open or

guards off.

WARNING

G Los humos fuera de la zona de res-

piración.

G Mantenga la cabeza fuera de los

humos. Utilice ventilación o aspiración para gases.

G Gardez la tête à l’écart des fumées. G Utilisez un ventilateur ou un aspira-

teur pour ôter les fumées des zones de travail.

G Vermeiden Sie das Einatmen von

Schweibrauch!

G Sorgen Sie für gute Be- und

Entlüftung des Arbeitsplatzes!

G Mantenha seu rosto da fumaça. G Use ventilação e exhaustão para

remover fumo da zona respiratória.

G Desconectar el cable de ali-

mentación de poder de la máquina antes de iniciar cualquier servicio.

G Débranchez le courant avant l’entre-

tien.

G Strom vor Wartungsarbeiten

abschalten! (Netzstrom völlig öffnen; Maschine anhalten!)

G Não opere com as tampas removidas. G Desligue a corrente antes de fazer

serviço.

G Não toque as partes elétricas nuas.

G No operar con panel abierto o

guardas quitadas.

G N’opérez pas avec les panneaux

ouverts ou avec les dispositifs de protection enlevés.

G Anlage nie ohne Schutzgehäuse

oder Innenschutzverkleidung in Betrieb setzen!

G Mantenha-se afastado das partes

moventes.

G Não opere com os paineis abertos

ou guardas removidas.

Spanish

AVISO DE

PRECAUCION

French

ATTENTION

German

WARNUNG

Portuguese

ATENÇÃO

Japanese

Chinese

Korean

Arabic

LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.

Page 72

• World's Leader in Welding and Cutting Products •

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com