Lincoln Electric 2013 MKX Owner's Manual

lincolnowner.com

lincolncanada.com

November 2012
Third Printing
Owner’s Manual
Lincoln MKX
Litho in U.S.A.

2013 OWNER’S MANUAL LINCOLN MKX

LINCOLN MKX

2013

OWNER’S
MANUAL

DA1J 19A321 AA

Table of Contents 1

Introduction 9

Child Safety 17

Child seats...........................................19

Child seat positioning ...................................19

Booster seats .........................................21

Installing child safety seats ...............................24

Child safety locks ......................................31

Safety Belts 32

Fastening the safety belts ................................34

Safety belt height adjustment .............................38

Safetybeltwarninglightandindicatorchime..................38

Safety belt-minder .....................................39

Child restraint and safety belt maintenance ...................41

Personal Safety System 42

Supplementary Restraints System 43

Driver and passenger airbags .............................45

Front passenger sensing system ...........................47

Side airbags ..........................................51

Safety canopy curtain airbags .............................52

Crash sensors and airbag indicator .........................54

Airbag disposal........................................55

Keys and Remote Control 56

General information on radio frequencies.....................56

Remote control .......................................57

Replacing a lost key or remote control.......................62

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

2 Table of Contents

MyKey 63

Settings, MyKey .......................................63

Creating.............................................64

Clearing.............................................65

System status.........................................65

Remote start, MyKey ...................................65

Troubleshooting, MyKey .................................67

Locks 69

Locking and unlocking ..................................69

SecuriCode™ keyless entry keypad .........................77

Security 79

SecuriLock® passive anti-theft system.......................79

Anti-theft alarm .......................................81

Steering Wheel 82

Adjusting the steering wheel ..............................82

Steering wheel controls .................................84

Wipers and Washers 87

Windshield wipers .....................................87

Rain-sensing wipers ....................................87

Windshield washers ....................................88

Rear-window wiper and washer ............................88

Lighting 89

Lighting control .......................................89

Autolamps ...........................................89

Instrument lighting dimmer...............................90

Headlamp exit delay ....................................90

Daytime running lamps..................................91

Front fog lamps.......................................92

Adaptive headlamps ....................................92

Directionindicators ....................................93

Interior lamps ........................................93

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Table of Contents 3

Windows and Mirrors 95

Power windows .......................................95

Exteriormirrors.......................................96

Interior mirrors .......................................98

Sun visors ...........................................99

Moonroof ...........................................100

Instrument Cluster 102

Gauges.............................................102

Warning lamps and indicators ............................102

Audible warnings and indicators ..........................107

Information Displays 108

Controls............................................108

Information messages ..................................114

Audio System 123

MyLincoln Touch™ system ..............................125

Climate Control 127

Dual automatic temperature control........................127

Rear window defroster .................................129

Cabin air filter .......................................130

Seats 132

Sitting in the correct position ............................132

Head restraints.......................................133

Power seats .........................................135

Memory function .....................................136

Heated and cooled seats ................................137

Rear seats ..........................................139

Universal Garage Door Opener 143

HomeLink® wireless control system .......................144

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

4 Table of Contents

Auxiliary Power Points 149

Storage Compartments 150

Center console .......................................150

Overhead console .....................................150

Starting and Stopping the Engine 151

Starting the engine ....................................154

Engine block heater ...................................155

Fuel and Refueling 157

Fuel quality .........................................158

Running out of fuel....................................159

Refueling...........................................160

Fuel consumption .....................................162

Transmission 166

Automatic transmission.................................166

Hill start assist .......................................170

All-Wheel Drive (If Equipped) 172

All wheel drive .......................................172

Brakes 179

Brakes .............................................179

Hints on driving with anti-lock brakes ......................180

Parking brake........................................180

Traction Control 181

TractionControl™....................................181

Stability Control 182

AdvanceTrac® .......................................183

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Table of Contents 5

Parking Aids 184

Sensing system.......................................184

Rear-view camera system ...............................186

Cruise Control 190

Using cruise control ...................................190

Using Adaptive Cruise Control............................191

Driving Aids 200

Blind Spot Information System (BLIS) with Cross Traffic

Alert(CTA).........................................200

Collision warning system ................................205

Steering ............................................209

Load Carrying 210

Cargo net...........................................210

Roof racks and load carriers .............................212

Utility hooks.........................................213

Vehicle loading .......................................213

Towing 221

Trailertowing........................................221

Wrecker towing ......................................227

Recreational towing ...................................228

Driving Hints 230

Economical driving ....................................230

Driving through water..................................231

Floormats..........................................232

Roadside Emergencies 234

Getting roadside assistance ..............................234

Hazard warning flashers ................................235

Fuel cut-off switch ....................................236

Jump-starting the vehicle ...............................236

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

6 Table of Contents

Customer Assistance 240

Reporting safety defects (U.S. only) .......................247

Reporting safety defects (Canada only) .....................247

Fuses 248

Changing a fuse ......................................248

Fuse specification chart ................................249

Maintenance 257

General information ...................................257

Opening and closing the hood ............................258

Under hood overview ..................................259

Engine oil dipstick ....................................260

Engine oil check......................................260

Engine coolant check ..................................261

Automatic transmission fluid check ........................265

Brake fluid check .....................................267

Fuel filter...........................................268

Washer fluid check ....................................268

Changing the vehicle battery .............................268

Checking the wiper blades ..............................271

Changing the wiper blades ..............................271

Air filter(s) .........................................272

Adjusting the headlamps ................................273

Changing a bulb ......................................275

Bulb specification chart.................................280

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Table of Contents 7

Vehicle Care 281

Cleaning products.....................................281

Cleaning the exterior ..................................281

Waxing.............................................283

Repairing minor paint damage ............................283

Cleaning the engine ...................................283

Cleaning the windows and wiper blades .....................284

Cleaning the interior ...................................284

Cleaning the instrument panel and instrument cluster lens .......285

Cleaning leather seats ..................................286

Cleaning the alloy wheels ...............................286

Vehiclestorage.......................................287

Wheels and Tires 290

Tire care ...........................................292

Using snow chains ....................................307

Tire Pressure Monitoring System (TPMS) ...................308

Changing a road wheel .................................313

Technical specifications.................................319

Wheel lug nut torque ..................................319

Capacities and Specifications 320

Engine specifications ..................................320

Part numbers ........................................324

Vehicle identification number ............................324

Vehicle certification label ...............................325

Transmission code designation............................326

Accessories 327

Accessories .........................................327

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

8 Table of Contents

Ford Extended Service Plan 329

Scheduled Maintenance 332

Normal scheduled maintenance and log .....................337

MyLincoln Touch™ 349

Infotainment display ...................................355

Voice recognition .....................................356

Listening to music ....................................362

Phone features .......................................384

Information Menu .....................................392

Settings............................................403

Climatefeatures......................................414

Navigation system.....................................418

Appendices 430

Index 450

The information contained in this publication was correct at the time of going to
print. In the interest of continuous development, we reserve the right to change
specifications, design or equipment at any time without notice or obligation.
No part of this publication may be reproduced, transmitted, stored in a retrieval
system or translated into any language in any form by any means without our
written permission. Errors and omissions excepted.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

© Ford Motor Company 2012

Introduction 9

ABOUT THIS MANUAL

Thank you for choosing Ford. We recommend that you take some time
to get to know your vehicle by reading this manual. The more that you
know about it, the greater the safety and pleasure you will get from
driving it.

WARNING: Always drive with due care and attention when
using and operating the controls and features on your vehicle.

Note: This manual describes a range of product features and options,
sometimes before they are generally available. Therefore, you may find
options in this manual that are not found on your vehicle.

Note: Some of the illustrations in this manual may be used for different
models, so they may appear different than your vehicle. However, the
essential information in the illustrations is always correct.

Note: Always use and operate your vehicle in line with all applicable
laws and regulations.

Note: Pass on this manual when selling your vehicle. It is an integral
part of the vehicle.

This manual may qualify the location of a component as left-hand side or
right-hand side. The side is determined when facing forward in the seat.

A

A. Right-hand side
B. Left-hand side

Protecting the Environment

You must play your part in protecting the environment. Correct
vehicle usage and the authorized disposal of waste, cleaning
and lubrication materials are significant steps toward this aim.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

B

10 Introduction

SYMBOL GLOSSARY

WARNING: You risk death or serious injury to yourself and
others if you do not follow the instruction highlighted by the

warning symbol.

These are some of the symbols you may see on your vehicle.

Symbol Description Symbol Description Symbol Description

Safety alert See Owner’s

Manual

Avoid
smoking,
flames, or
sparks

Brake
fluid – non
petroleum
base

Check fuel
cap

Child seat
tether anchor

Battery Battery acid

Brake system Cabin air

Child Safety
Door Lock
and Unlock

Cruise control Do not open

Anti-lock
braking
system

filter

Child seat
lower anchor

when hot

Engine air
filter

Engine oil Explosive gas Fan warning

Fasten safety
belt

Fuel pump
reset

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Engine
coolant

Front airbag Front fog

Fuse
compartment

Engine
coolant
temperature

lamps

Hazard
warning
flasher

Introduction 11

Symbol Description Symbol Description Symbol Description

Heated rear
window

Lighting
control

Panic alarm Parking aid

Interior
luggage
compartment
release

Low tire
pressure
warning

system

Jack

Maintain
correct fluid
level

Parking brake
system

Power
steering fluid

Service
engine soon

Windshield
defrost and
demist

DATA RECORDING

Service Data Recording

Service data recorders in your vehicle are capable of collecting and
storing diagnostic information about your vehicle. This potentially
includes information about the performance or status of various systems
and modules in the vehicle, such as engine, throttle, steering or brake
systems. In order to properly diagnose and service your vehicle, Ford
Motor Company, Ford of Canada, and service and repair facilities may
access or share among them vehicle diagnostic information received
through a direct connection to your vehicle when diagnosing or servicing
your vehicle. Additionally, when your vehicle is in for service or repair,
Ford Motor Company, Ford of Canada, and service and repair facilities
may access or share among them data for vehicle improvement purposes.
For U.S. only (if equipped), if you choose to use the SYNC® Vehicle
Health Report, you consent that certain diagnostic information may also
be accessed electronically by Ford Motor Company and Ford authorized
service facilities, and that the diagnostic information may be used for any
purpose. See the SYNC® chapter for more information.

Power
windows front
and rear

Side airbag Stability

Windshield
washer and
wiper

Power
window
lockout

control

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

12 Introduction

Event Data Recording

This vehicle is equipped with an event data recorder (EDR).
The main purpose of an EDR is to record, in certain crash or
near crash-like situations, such as an airbag deployment or
hitting a road obstacle; this data will assist in understanding how
a vehicle’s systems performed. The EDR is designed to record
data related to vehicle dynamics and safety systems for a short
period of time, typically 30 seconds or less. The EDR in this
vehicle is designed to record such data as:

• How various systems in your vehicle were operating;

• Whether or not the driver and passenger safety belts were

buckled/fastened;

• How far (if at all) the driver was depressing the accelerator
and/or the brake pedal;

• How fast the vehicle was travelling;

• Where the driver was positioning the steering wheel

(if equipped).

This data can help provide a better understanding of the
circumstances in which crashes and injuries occur.

Note: EDR data is recorded by your vehicle only if a non-trivial
crash situation occurs; no data is recorded by the EDR under
normal driving conditions and no personal data or information
(e.g., name, gender, age, and crash location) is recorded
(see limitations regarding 911 Assist and Traffic, Directions
and Information privacy below). However, parties, such as law
enforcement, could combine the EDR data with the type of
personally identifying data routinely acquired during a crash
investigation.

To read data recorded by an EDR, special equipment is required,
and access to the vehicle or the EDR is needed. In addition to
the vehicle manufacturer, other parties, such as law enforcement,
that have such special equipment, can read the information if
they have access to the vehicle or the EDR. Ford Motor Company
and Ford of Canada do not access event data recorder
information without obtaining consent, unless pursuant to court
order or where required by law enforcement, other government
authorities or other third parties acting with lawful authority.
Other parties may seek to access the information independently
of Ford Motor Company and Ford of Canada.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Introduction 13

Note: Including to the extent that any law pertaining to Event
Data Recorders applies to SYNC® or its features, please note
the following: Once 911 Assist (if equipped) is enabled (set ON),
911 Assist may, through any paired and connected cell phone,
disclose to emergency services that the vehicle has been in a
crash involving the deployment of an airbag or, in certain
vehicles, the activation of the fuel pump shut-off. Certain
versions or updates to 911 Assist may also be capable of being
used to electronically or verbally provide to 911 operators the
vehicle location (such as latitude and longitude), and/or other
details about the vehicle or crash or personal information about
the occupants to assist 911 operators to provide the most
appropriate emergency services. If you do not want to disclose
this information, do not activate the 911 Assist feature. See your
SYNC® chapter for more information.

Additionally, when you connect to Traffic, Directions and
Information (if equipped, U.S. only), the service uses GPS
technology and advanced vehicle sensors to collect the vehicle’s
current location, travel direction, and speed (“vehicle travel
information”), only to help provide you with the directions,
traffic reports, or business searches that you request. If you do
not want Ford or its vendors to receive this information, do not
activate the service. Ford Motor Company and the vendors it uses
to provide you with this information do not store your vehicle
travel information. For more information, see Traffic, Directions
and Information, Terms and Conditions. See your SYNC®
supplement for more information.

CALIFORNIA PROPOSITION 65

WARNING: Some constituents of engine exhaust, certain vehicle

components, certain fluids contained in vehicles and certain
products of component wear contain or emit chemicals known to
the State of California to cause cancer and birth defects or other
reproductive harm.

PERCHLORATE MATERIAL

Note: Certain components in your vehicle, such as airbag modules,
safety belt pretensioners, and remote control batteries, may contain
perchlorate material. Special handling may apply for service or vehicle
end of life disposal. See www.dtsc.ca.gov/hazardouswaste/perchlorate
for more information.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

14 Introduction

LINCOLN AUTOMOTIVE FINANCIAL SERVICES (U.S. ONLY)

Lincoln Automotive Financial Services offers a full range of financing and
lease plans to help you acquire your vehicle. If you have financed or
leased your vehicle through Lincoln Automotive Financial Services,
thank you for your business.

For your convenience we offer a number of ways to contact us, as well
as help manage your account.

Phone: [phone]
For more information regarding Lincoln Automotive Financial Services,

as well as access Account Manager, please go to www.LincolnAFS.com.

REPLACEMENT PARTS RECOMMENDATION

Your vehicle has been built to the highest standards using quality parts.
We recommend that you demand the use of genuine Ford and Motorcraft
parts whenever your vehicle requires scheduled maintenance or repair.
You can clearly identify genuine Ford and Motorcraft parts by looking
for the Ford, FoMoCo or Motorcraft branding on the parts or their
packaging.

Scheduled Maintenance and Mechanical Repairs

One of the best ways for you to make sure that your vehicle
provides years of service is to have it maintained in line with our
recommendations using parts that conform to the specifications detailed
in this owner’s manual. Genuine Ford and Motorcraft parts meet or
exceed these specifications.

Collision Repairs

We hope that you never experience a collision, but accidents do
happen. Genuine Ford replacement collision parts meet our stringent
requirements for fit, finish, structural integrity, corrosion protection and
dent resistance. During vehicle development, we validate that these parts
deliver the intended level of protection as a whole system. A great way
to know for sure you are getting this level of protection is to use genuine
Ford replacement collision parts.

Warranty on Replacement Parts

Genuine Ford and Motorcraft replacement parts are the only
replacement parts that benefit from a Ford Warranty. Damage caused
to your vehicle as a result of the failure of non-Ford parts may not be
covered by the Ford Warranty. For additional information, see the terms
and conditions of the Ford Warranty.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Introduction 15

SPECIAL NOTICES

New Vehicle Limited Warranty

For a detailed description of what is covered and what is not covered
by your vehicle’s New Vehicle Limited Warranty, see the warranty
information that is provided to you along with your owner’s manual.

Special Instructions

For your added safety, your vehicle is fitted with sophisticated electronic
controls.

WARNING: Please read the Supplementary Restraints System

chapter. Failure to follow the specific warnings and instructions
could result in personal injury.

WARNING: Front seat mounted rear-facing child or infant seats

should NEVER be placed in front of an active passenger airbag.

MOBILE COMMUNICATIONS EQUIPMENT

Using mobile communications equipment is becoming increasingly
important in the conduct of business and personal affairs. However,
you must not compromise your own or others’ safety when using such
equipment. Mobile communications can enhance personal safety and
security when appropriately used, particularly in emergency situations.
Safety must be paramount when using mobile communications
equipment to avoid negating these benefits.

Mobile communication equipment includes, but is not limited to, cellular
phones, pagers, portable email devices, text messaging devices and
portable two-way radios.

WARNING: Driving while distracted can result in loss of vehicle

control, accident and injury. Ford strongly recommends that you
use extreme caution when using any device or feature that may take
your focus off the road. Your primary responsibility is the safe operation
of your vehicle. We recommend against the use of any handheld device
while driving, encourage the use of voice operated systems when
possible and that you become aware of applicable state and local
laws that may affect use of electronic devices while driving.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

16 Introduction

EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLE
SPECIFIC INFORMATION

For your particular global region, your vehicle may be equipped with
features and options that are different from the features and options
that are described in this owner’s manual. A market unique supplement
may be supplied that complements this book. By referring to the market
unique supplement, if provided, you can properly identify those features,
recommendations and specifications that are unique to your vehicle.
This owner’s manual is written primarily for the U.S. and Canadian
Markets. Features or equipment listed as standard may be different
on units built for Export. See this owner’s manual for all other

required information and warnings.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Child Safety 17

GENERAL INFORMATION

See the following sections for directions on how to properly use safety
restraints for children.

WARNING: Always make sure your child is secured properly in a

device that is appropriate for their height, age and weight. Child
safety restraints must be bought separately from your vehicle. Failure
to follow these instructions and guidelines may result in an increased
risk of serious injury or death to your child.

WARNING:

recommendations for safety restraints are based on probable
child height, age and weight thresholds from NHTSA and other
safety organizations, or are the minimum requirements of law. Ford
recommends checking with a NHTSA Certified Child Passenger Safety
Technician and consulting your pediatrician to make sure your child
seat is appropriate for your child, and is compatible with and properly
installed in your vehicle. To locate a child seat fitting station and CPST,
contact the NHTSA toll free at 1-888-327-4236 or locate NHTSA on the
internet. In Canada, check with your local St. John Ambulance office for
referral to a CPST or for further information, contact your provincial
ministry of transportation, or locate your local St. John Ambulance office
by searching for St. John Ambulance on the internet, or Transport
Canada at 1–800–333–0371 (http://www.tc.gc.ca). Failure to properly
restrain children in safety seats made especially for their height, age,
and weight may result in an increased risk of serious injury or death to
your child.

All children are shaped differently. The

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

18 Child Safety

Recommendations for Safety Restraints for Children

Child size, height, weight, or
age

Infants
or
toddlers

Small
children

Larger
children

• You are required by law to properly use safety seats for infants and
toddlers in the United States and Canada.

• Many states and provinces require that small children use approved
booster seats until they reach age eight, a height of 4 feet 9 inches
(1.45 meters) tall, or 80 pounds (36 kilograms). Check your local and
state or provincial laws for specific requirements about the safety of
children in your vehicle.

• When possible, always properly restrain children twelve (12) years of
age and under in a rear seating position of your vehicle. Accident
statistics suggest that children are safer when properly restrained in
the rear seating positions than in a front seating position. See Front
Passenger Sensing System in the Supplementary Restraints System
chapter for more information.

Children weighing 40 lb (18 kg) or
less (generally age four or
younger).

Children who have outgrown or no
longer properly fit in a child safety
seat (generally children who are
less than 4 ft. 9 in. (1.45 m) tall,
are greater than age four (4) and
less than age twelve (12), and
between 40 lb (18 kg) and
80 lb (36 kg) and upward to
100 lb (45 kg) if recommended by
your child restraint manufacturer).

Children who have outgrown
or no longer properly fit in a
belt-positioning booster seat
(generally children who are at
least 4 ft. 9 in. (1.45 m) tall or
greater than 80 lb (36 kg) or
100 lb (45 kg) if recommended by
child restraint manufacturer).

Recommended
restraint type

Use a child safety seat
(sometimes called an
infant carrier,
convertible seat, or
toddler seat).

Use a belt-positioning
booster seat.

Use a vehicle safety
belt having the lap belt
snug and low across
the hips, shoulder belt
centered across the
shoulder and chest,
and seat back upright.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

CHILD SEATS

CHILD SEAT POSITIONING

Child Safety 19

Use a child safety seat (sometimes
called an infant carrier, convertible
seat, or toddler seat) for infants,
toddlers or children weighing
40 pounds (18 kilograms) or less
(generally age four or younger).

WARNING:

place a rear-facing child seat in front of an active airbag. If you must
use a forward-facing child seat in the front seat, move the vehicle seat
upon which the child seat is installed all the way back. When possible, all
children age 12 and under should be properly restrained in a rear seating
position. If all children cannot be seated and restrained properly in a rear
seating position, properly restrain the largest child in the front seat.

WARNING:

provided by the manufacturer of any child restraint to determine if
the restraint device is appropriate for your child’s size, height, weight, or
age. Follow the child restraint manufacturer’s instructions and warnings
provided for installation and use in conjunction with the instructions and
warnings provided by your vehicle manufacturer. A safety seat that is
improperly installed or utilized, is inappropriate for your child’s height, age,
or weight or does not properly fit the child may increase the risk of serious
injury or death.

WARNING: Never let a passenger hold a child on his or her lap

while your vehicle is moving. The passenger cannot protect the
child from injury in a crash, which may result in serious injury or death.

WARNING: Never use pillows, books, or towels to boost a child.

They can slide around and increase the likelihood of injury or
death in a crash.

Airbags can kill or injure a child in a child seat. NEVER

Always carefully follow the instructions and warnings

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

20 Child Safety

WARNING: Always restrain an unoccupied child seat or booster
seat. These objects may become projectiles in a crash or sudden

stop, which may increase the risk of serious injury.

WARNING: Never place, or allow a child to place, the shoulder

belt under a child’s arm or behind the back because it reduces
the protection for the upper part of the body and may increase the risk
of injury or death in a crash.

WARNING: Do not leave children or pets unattended in your

vehicle.

Use any attachment method as indicated

below by X.

LATCH

(lower
Restraint
Type

Rear­facing
child seat

Forward­facing
child seat

Forward­facing
child seat

Note: The child seat must rest tightly against the vehicle seat upon
which it is installed. It may be necessary to lift or remove the head
restraint. See the Seats chapter for information on head restraints.

Child

Weight

Up to
48 lb
(21 kg)

Up to
48 lb
(21 kg)

Over
48 lb
(21 kg)

anchors

and

top

tether

anchor)

LATCH
(lower
anchors
only)

XX

XXX

Safety
belt
and
top
tether
anchor

Safety
belt and
LATCH
(lower
anchors
and top
tether
anchor)

XX

Safety
belt
only

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Child Safety 21

BOOSTER SEATS

WARNING: Never place, or allow a child to place, the shoulder

belt under a child’s arm or behind the back because it reduces
the protection for the upper part of the body and may increase the risk
of injury or death in a crash.

Use a belt-positioning booster seat for children who have outgrown or no
longer properly fit in a child safety seat (generally children who are less
than 4 feet 9 inches (1.45 meters) tall, are greater than age four (4) and
less than age twelve (12), and between 40 pounds (18 kilograms) and
80 pounds (36 kilograms) and upward to 100 pounds (45 kilograms) if
recommended by your child restraint manufacturer). Many state and
provincial laws require that children use approved booster seats until
they reach age eight (8), a height of 4 feet 9 inches (1.45 meters) tall,
or 80 pounds (36 kilograms).

Booster seats should be used until you can answer YES to ALL of these
questions when the child is seated without a booster seat.

• Can the child sit all the way
back against their vehicle seat
with knees bent comfortably at
the edge of the seat cushion?

• Can the child sit without
slouching?

• Does the lap belt rest low across the hips?

• Is the shoulder belt centered on the shoulder and chest?

• Can the child stay seated like this for the whole trip?

Always use booster seats in conjunction with your vehicle lap and
shoulder belt.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

22 Child Safety

Types of Booster Seats

• Backless booster seats

If your backless booster seat has a removable shield, remove the shield.
If a vehicle seating position has a low seat back or no head restraint, a
backless booster seat may place your child’s head (as measured at the
tops of the ears) above the top of the seat. In this case, move the
backless booster to another seating position with a higher seat back or
head restraint and lap and shoulder belts, or consider using a high back
booster seat.

• High back booster seats

If, with a backless booster seat, you cannot find a seating position that
adequately supports your child’s head, a high back booster seat would be
a better choice.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Child Safety 23

Children and booster seats vary in size and shape. Choose a booster that
keeps the lap belt low and snug across the hips, never up across the
stomach, and lets you adjust the shoulder belt to cross the chest and rest
snugly near the center of the shoulder. The following drawings compare
the ideal fit (center) to a shoulder belt uncomfortably close to the neck
and a shoulder belt that could slip off the shoulder. The drawings also
show how the lap belt should be low and snug across the child’s hips.

If the booster seat slides on the vehicle seat upon which it is being used,
placing a rubberized mesh sold as shelf or carpet liner under the booster
seat may improve this condition. Do not introduce any item thicker than
this under the booster seat. Check with the booster seat manufacturer’s
instructions.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

24 Child Safety

INSTALLING CHILD SEATS

Using Lap and Shoulder Belts

WARNING: Airbags can kill or injure a child in a child seat.
NEVER place a rear-facing child seat in front of an active airbag.

If you must use a forward-facing child seat in the front seat, move the
seat all the way back.

WARNING: Airbags can kill or injure a child in a child seat.
Children 12 and under should be properly restrained in the rear

seat whenever possible.

WARNING: Depending on where you secure a child restraint,

and depending on the child restraint design, you may block
access to certain safety belt buckle assemblies or LATCH lower
anchors, rendering those features potentially unusable. To avoid risk of
injury, occupants should only use seating positions where they are able
to be properly restrained.

When installing a child safety seat with combination lap and shoulder
belts:

• Use the correct safety belt buckle for that seating position.

• Insert the belt tongue into the proper buckle until you hear a snap

and feel it latch. Make sure the tongue is securely fastened in the
buckle.

• Keep the buckle release button pointing up and away from the safety
seat, with the tongue between the child seat and the release button,
to prevent accidental unbuckling.

• Place the vehicle seat upon which the child seat will be installed in
the upright position.

• Put the safety belt in the automatic locking mode. See Step 5. This
vehicle does not require the use of a locking clip.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Child Safety 25

Perform the following steps when installing the child seat with
combination lap and shoulder belts:

Note: Although the child seat illustrated is a forward-facing child seat,
the steps are the same for installing a rear-facing child seat.

1. Position the child safety seat in a
seat with a combination lap and
shoulder belt.

2. Pull down on the shoulder belt
and then grasp the shoulder belt
and lap belt together.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

3. While holding the shoulder and
lap belt portions together, route
the tongue through the child
seat according to the child seat
manufacturer’s instructions. Be sure
the belt webbing is not twisted.

26 Child Safety

4. Insert the belt tongue into the
proper buckle (the buckle closest to
the direction the tongue is coming
from) for that seating position until
you hear a snap and feel the latch
engage. Make sure the tongue is
latched securely by pulling on it.

5. To put the retractor in the
automatic locking mode, grasp the
shoulder portion of the belt and pull
downward until all of the belt is
pulled out.

Note: The automatic locking mode is available on the front passenger
and rear seats. This vehicle does not require the use of a locking clip.

6. Allow the belt to retract to remove slack. The belt will click as it

retracts to indicate it is in the automatic locking mode.

7. Try to pull the belt out of the retractor to make sure the retractor is

in the automatic locking mode. You should not be able to pull more belt
out. If the retractor is not locked, unbuckle the belt and repeat Steps 5
and 6.

8. Remove remaining slack from the
belt. Force the seat down with extra
weight, for example, by pressing
down or kneeling on the child
restraint while pulling up on the
shoulder belt in order to force
slack from the belt.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Child Safety 27

This is necessary to remove the remaining slack that will exist once the
extra weight of the child is added to the child restraint. It also helps
to achieve the proper snugness of the child seat to your vehicle.
Sometimes, a slight lean toward the buckle will additionally help
to remove remaining slack from the belt.

9. Attach the tether strap (if the child seat is equipped). See Using
Tether Straps later in this chapter.

10. Before placing the child in the
seat, forcibly move the seat forward
and back to make sure the seat is
securely held in place.

To check this, grab the seat at the belt path and attempt to move it side
to side and forward and back. There should be no more than 1 inch
(2.5 centimeters) of movement for proper installation.

Ford recommends checking with a NHTSA Certified Child Passenger
Safety Technician (CPST) to make certain the child restraint is properly
installed. In Canada, check with your local St. John Ambulance office for
referral to a CPST.

Using Lower Anchors and Tethers for CHildren (LATCH)

WARNING: Never attach two child safety seats to the same

anchor. In a crash, one anchor may not be strong enough to hold
two child safety seat attachments and may break, causing serious injury
or death.

WARNING: Depending on where you secure a child restraint,

and depending on the child restraint design, you may block
access to certain safety belt buckle assemblies or LATCH lower
anchors, rendering those features potentially unusable. To avoid risk
of injury, occupants should only use seating positions where they are
able to be properly restrained.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

28 Child Safety

The LATCH system is composed of three vehicle anchor points: two
lower anchors located where your vehicle seat back and seat cushion
meet (called the seat bight) and one top tether anchor located behind
that seating position.

LATCH compatible child safety seats have two rigid or webbing mounted
attachments that connect to the two lower anchors at the LATCH
equipped seating positions in your vehicle. This type of attachment
method eliminates the need to use safety belts to attach the child
seat, however the safety belt can still be used to attach the child seat.
For forward-facing child seats, the top tether strap must also be attached
to the proper top tether anchor, if a top tether strap has been provided
with your child seat.

Your vehicle has LATCH lower
anchors for child seat installation
at the seating positions marked
with the child seat symbol.

The LATCH anchors are located at
the rear section of the rear seat
between the cushion and seat
back below the symbols as shown.
Follow the child seat manufacturer’s
instructions to properly install a
child seat with LATCH attachments.

Follow the instructions on attaching child safety seats with tether straps.
See Using Tether Straps in this chapter.

Attach LATCH lower attachments of the child seat only to the anchors
shown.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Child Safety 29

Use of Inboard Lower Anchors from the Outboard Seating
Positions (Center Seating Use)

Note: The standardized spacing for LATCH lower anchors is 11 inches.
(28 centimeters) center to center. Do not use LATCH lower anchors
for the center seating position unless the child seat manufacturer’s
instructions permit and specify using anchors spaced at least as far
apart as those in this vehicle.

The lower anchors at the center of the second row rear seat are spaced
18 inches (46 centimeters) apart. A child seat with rigid LATCH
attachments cannot be installed at the center seating position. LATCH
compatible child seats (with attachments on belt webbing) can only be
used at this seating position provided that the child seat manufacturer’s
instructions permit use with the anchor spacing stated. Do not attach a
child seat to any lower anchor if an adjacent child seat is attached to
that anchor.

Each time you use the safety seat, check that the seat is properly
attached to the lower anchors and tether anchor, if applicable. Tug the
child seat from side to side and forward and back where it is secured to
your vehicle. The seat should move less than one inch when you do this
for a proper installation.

If the safety seat is not anchored properly, the risk of a child being
injured in a crash greatly increases.

Combining Safety Belt and LATCH Lower Anchors for Attaching
Child Safety Seats

When used in combination, either the safety belt or the LATCH lower
anchors may be attached first, provided a proper installation is achieved.
Attach the tether strap afterward, if included with the child seat.

Using Tether Straps

Many forward-facing child safety seats include a tether strap
which extends from the back of the child safety seat and hooks
to an anchoring point called the top tether anchor. Tether

straps are available as an accessory for many older safety seats.
Contact the manufacturer of your child seat for information about

ordering a tether strap, or to obtain a longer tether strap if the tether
strap on your safety seat does not reach the appropriate top tether
anchor in your vehicle.

Once the child safety seat has been installed using either the safety belt,
the lower anchors of the LATCH system, or both, you can attach the top
tether strap.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

30 Child Safety

The tether strap anchors in your vehicle are in the following positions
(shown from top view):

Perform the following steps to install a child safety seat with tether
anchors:

Note: If you install a child seat with rigid LATCH attachments, do not
tighten the tether strap enough to lift the child seat off your vehicle seat
cushion when the child is seated in it. Keep the tether strap just snug
without lifting the front of the child seat. Keeping the child seat just
touching your vehicle seat gives the best protection in a severe crash.

1. Route the child safety seat tether strap over the back of the seat.

For outboard seating positions, route the tether strap under the head
restraint and between the head restraint posts. For the center seating
positions, route the tether strap over the top of the head restraint. If
needed, the head restraints can also be removed.

2. Locate the correct anchor behind
the gap cover for the selected
seating position.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

3. Pull the gap cover reward to
expose the anchors. Clip the tether
strap to the anchor as shown.

Child Safety 31

4. Tighten the child safety seat tether strap according to the
manufacturer’s instructions.

If your child restraint system is equipped with a tether strap, and the
child restraint manufacturer recommends its use, Ford also recommends
its use.

CHILD SAFETY LOCKS

The childproof locks are located on the rear edge of each rear door and
must be set separately for each door.

When these locks are set, the rear
doors cannot be opened from the
inside.

• Insert the key and turn to the
lock position (key horizontal) to
engage the childproof locks.

• Insert the key and turn to the
unlock position (key vertical) to
disengage the childproof locks.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

32 Safety Belts

PRINCIPLES OF OPERATION

WARNING: Never let a passenger hold a child on his or her lap
while the vehicle is moving. The passenger cannot protect the

child from injury in a crash.

WARNING: It is extremely dangerous to ride in a cargo area,

inside or outside of a vehicle. In a crash, people riding in these
areas are more likely to be seriously injured or killed. Do not allow
people to ride in any area of your vehicle that is not equipped with
seats and safety belts. Be sure everyone in your vehicle is in a seat
and using a safety belt properly.

WARNING: Always drive and ride with your seat back upright

and the lap belt snug and low across the hips.

WARNING: To reduce the risk of injury, make sure children sit

where they can be properly restrained.

WARNING: All occupants of the vehicle, including the driver,

should always properly wear their safety belts, even when an
airbag supplemental restraint system is provided.

WARNING:

more likely to die than a person wearing a safety belt.

WARNING: Each seating position in your vehicle has a specific

safety belt assembly which is made up of one buckle and one
tongue that are designed to be used as a pair. 1) Use the shoulder belt
on the outside shoulder only. Never wear the shoulder belt under the
arm. 2) Never swing the safety belt around your neck over the inside
shoulder. 3) Never use a single belt for more than one person.

WARNING: When possible, all children 12 years old and under

should be properly restrained in a rear seating position.

In a rollover crash, an unbelted person is significantly

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Safety Belts 33

WARNING: Safety belts and seats can become hot in a vehicle

that has been closed up in sunny weather; they could burn a
small child. Check seat covers and buckles before you place a child
anywhere near them.

WARNING: Front and rear seat occupants, including pregnant

women, should wear safety belts for optimum protection in an
accident.

All seating positions in this vehicle have lap and shoulder safety belts. All
occupants of the vehicle should always properly wear their safety belts,
even when an airbag supplemental restraint system is provided.

The safety belt system consists of:

• lap and shoulder safety belts

• shoulder safety belt with automatic locking mode (except driver

safety belt)

• height adjuster at the front outboard seating positions

• safety belt pretensioner at the front outboard seating positions

• belt tension sensor at the front outboard passenger seating position.

• safety belt warning light and chime. See Safety belt warning

light and indicator chime later in this chapter.

• crash sensors and monitoring system with readiness
indicator. See Crash sensors and airbag indicator in
the Supplemental Restraint System chapter.

The safety belt pretensioners are designed to activate in frontal,
near-frontal and side crashes, and in rollovers. The safety belt
pretensioners at the front seating positions are designed to tighten
the safety belts firmly against the occupant’s body when activated.
This helps increase the effectiveness of the safety belts. In frontal
crashes, the safety belt pretensioners can be activated alone or, if the
crash is of sufficient severity, together with the front airbags.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

34 Safety Belts

FASTENING THE SAFETY BELTS

The front outboard and rear safety restraints in your vehicle are
combination lap and shoulder belts.

1. Insert the belt tongue into the
proper buckle (the buckle closest to
the direction the tongue is coming
from) until you hear a snap and feel
it latch. Make sure the tongue is
securely fastened in the buckle.

2. To unfasten, press the release
button and remove the tongue from
the buckle.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

When in use, the rear outboard safety
belts can be used with the comfort
guides. This guide is attached to the
head restraint and is stored in a pocket
in the seat back.

Safety Belts 35

To adjust the comfort guide:

1. Slip the shoulder belt into the
belt guide.

2. Slide the guide up or down along
the webbing so that the belt is
centered on the occupant’s
shoulder.

Restraint of Pregnant Women

WARNING: Always ride and drive with your seat back upright

and the safety belt properly fastened. The lap portion of the
safety belt should fit snug and be positioned low across the hips.
The shoulder portion of the safety belt should be positioned across
the chest. Pregnant women should also follow this practice. See the
following figure.

Pregnant women should always
wear their safety belts. The lap belt
portion of a combination lap and
shoulder belt should be positioned
low across the hips below the belly
and worn as tight as comfort will
allow. The shoulder belt should be
positioned to cross the middle of
the shoulder and the center of the
chest.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

36 Safety Belts

Safety Belt Locking Modes

WARNING: After any vehicle crash, the safety belt system at all

passenger seating positions must be checked by an authorized
dealer to verify that the automatic locking retractor feature for child
seats is still functioning properly. In addition, all safety belts should be
checked for proper function.

WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE

REPLACED if the safety belt assembly automatic locking
retractor feature or any other safety belt function is not operating
properly when checked by an authorized dealer. Failure to replace the
belt and retractor assembly could increase the risk of injury in crashes.

All safety restraints in the vehicle are combination lap and shoulder
belts. The driver safety belt has the first type of locking mode, and the
front outboard passenger and rear seat safety belts have both types of
locking modes described as follows:

Vehicle Sensitive Mode

This is the normal retractor mode, which allows free shoulder belt
length adjustment to your movements and locking in response to vehicle
movement. For example, if the driver brakes suddenly or turns a corner
sharply, or the vehicle receives an impact of about 5 mph (8 km/h) or
more, the combination safety belts will lock to help reduce forward
movement of the driver and passengers.

In addition, the retractor is designed to lock if the webbing is pulled out
too quickly. If this occurs, let the belt retract slightly and pull webbing
out again in a slow and controlled manner.

Automatic Locking Mode

In this mode, the shoulder belt is automatically pre-locked. The belt will
still retract to remove any slack in the shoulder belt. The automatic
locking mode is not available on the driver safety belt.

When to Use the Automatic Locking Mode

This mode should be used any time a child safety seat, except a booster,
is installed in passenger front or rear seating positions. Children 12 years
old and under should be properly restrained in a rear seating position
whenever possible. See the Child Safety chapter.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Safety Belts 37

How to Use the Automatic Locking Mode

1. Buckle the combination lap and shoulder
belt.

2. Grasp the shoulder portion and pull
downward until the entire belt is pulled out.

3. Allow the belt to retract. As the belt
retracts, you will hear a clicking sound. This
indicates the safety belt is now in the
automatic locking mode.

How to Disengage the Automatic Locking Mode

Unbuckle the combination lap and shoulder belt and allow it to retract
completely to disengage the automatic locking mode and activate the
vehicle sensitive (emergency) locking mode.

Safety Belt Extension Assembly

WARNING: Do not use extensions to change the fit of the
shoulder belt across the torso.

If the safety belt is too short when fully extended, you can obtain a
safety belt extension assembly from an authorized dealer.

Use only extensions manufactured by the same supplier as the safety
belt. Manufacturer identification is located at the end of the webbing on
the label. Also, use the safety belt extension only if the safety belt is too
short for you when fully extended.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

38 Safety Belts

SAFETY BELT HEIGHT ADJUSTMENT

WARNING: Position the safety belt height adjusters so that the

belt rests across the middle of your shoulder. Failure to adjust
the safety belt properly could reduce the effectiveness of the seat belt
and increase the risk of injury in a collision.

Adjust the height of the shoulder belt so the
belt rests across the middle of your shoulder.

To adjust the shoulder belt height:

1. Pull on the center button and slide the height adjuster up or down.

2. Release the button and pull down on the height adjuster to make sure
it is locked in place.

SAFETY BELT WARNING LIGHT AND INDICATOR CHIME

This lamp illuminates and an audible warning will sound if the
driver’s safety belt has not been fastened when the vehicle’s
ignition is turned on.

Conditions of Operation

If... Then...

The driver’s safety belt is not buckled
before the ignition switch is turned to
the on position...

The driver’s safety belt is buckled
while the indicator light is illuminated
and the warning chime is sounding...
The driver’s safety belt is buckled
before the ignition switch is turned to
the on position...

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

The safety belt warning light
illuminates 1-2 minutes and
the warning chime sounds
4-8 seconds.
The safety belt warning light
and warning chime turn off.

The safety belt warning light
and indicator chime remain off.

Safety Belts 39

SAFETY BELT-MINDER®

This feature supplements the safety belt warning function by providing
additional reminders by intermittently sounding a chime and illuminating
the safety belt warning light when the driver’s or front passenger’s seat is
occupied and the safety belt is unbuckled.

The system uses information from the front passenger sensing system to
determine if a front seat passenger is present and therefore potentially in
need of a warning. To avoid activating the Belt-Minder® feature for objects
placed in the front passenger seat, warnings will only be given to front seat
occupants as determined by the front passenger sensing system.

If the Belt-Minder® warnings have expired (warnings for about five
minutes) for one occupant (driver or front passenger), the other
occupant can still activate the Belt-Minder® feature.

If... Then...

The driver’s and front
passenger’s safety belts are
buckled before the ignition
switch is turned to the
on position or less than
1-2 minutes have elapsed
since the ignition switch
has been turned to on...

The driver’s or front
passenger’s safety belt is not
buckled when the vehicle
has reached at least 6 mph
(9.7 km/h) and 1-2 minutes
have elapsed since the ignition
switch has been turned to on...

The driver’s or front
passenger’s safety belt becomes
unbuckled for about one
minute while the vehicle is
traveling at least 6 mph
(9.7 km/h) and more than
1-2 minutes have elapsed since
the ignition switch has been
turned to on...

The Belt-Minder® feature will not
activate.

The Belt-Minder® feature is activated

- the safety belt warning light
illuminates and the warning chime
sounds for six seconds every
25 seconds, repeating for about
five minutes or until the safety belts
are buckled.

The Belt-Minder® feature is activated

- the safety belt warning light
illuminates and the warning chime
sounds for six seconds every
25 seconds, repeating for about
five minutes or until the safety belts
are buckled.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

40 Safety Belts

Deactivating and Activating the Belt-Minder® Feature

WARNING: While the system allows you to deactivate it, this

system is designed to improve your chances of being safely
belted and surviving an accident. We recommend you leave the system
activated for yourself and others who may use the vehicle. To reduce
the risk of injury, do not deactivate or activate the system while driving
the vehicle.

Note: The driver and front passenger warning are deactivated and
activated independently. When deactivating or activating one seating
position, do not buckle the other position as this will terminate the
process.

Read Steps1-4thoroughly before proceeding with the programming
procedure.

Before following the procedure, make sure that:

• the parking brake is set

• the transmission selector lever is in position P.

• the ignition is off

• the driver and front passenger safety belts are unbuckled

1. Turn the ignition on. DO NOT START THE ENGINE.

2. Wait until the safety belt warning light turns off (about 1–2 minutes).

• Step 3 must be completed within 50 seconds after the safety belt
warning light turns off.

3. For the seating position being disabled, buckle then unbuckle the

safety belt three times at a moderate speed, ending in the unbuckled
state.

• After Step 3, the safety belt warning light will be turned on for
three seconds.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Safety Belts 41

4. Within about seven seconds of the light turning off, buckle then
unbuckle the safety belt.

• This will disable the feature for that seating position if it is currently
enabled.

• This will enable the feature for that seating position if it is currently
disabled.

One-time Belt-Minder® Disable

If at any time the driver or front passenger quickly buckles then
unbuckles the safety belt for that seating position, the system is disabled
for the current ignition cycle. The feature will enable during the same
ignition cycle if the occupant buckles and remains buckled for about
30 seconds. Confirmation is not given for the one-time disable.

CHILD RESTRAINT AND SAFETY BELT MAINTENANCE

Inspect the vehicle safety belts and child safety seat systems periodically
to make sure they work properly and are not damaged. Inspect the vehicle
and child seat safety belts to make sure there are no nicks, tears or
cuts. Replace if necessary. All vehicle safety belt assemblies, including
retractors, buckles, front safety belt buckle assemblies, buckle support
assemblies (slide bar-if equipped), shoulder belt height adjusters
(if equipped), shoulder belt guide on seat back (if equipped), child
safety seat LATCH and tether anchors, and attaching hardware, should
be inspected after a crash. Read the child restraint manufacturer’s
instructions for additional inspection and maintenance information specific
to the child restraint. Ford Motor Company recommends that all safety
belt assemblies in use in vehicles involved in a crash be replaced.
However, if the crash was minor and an authorized dealer finds that the
belts do not show damage and continue to operate properly, they do not
need to be replaced. Safety belt assemblies not in use during a crash
should also be inspected and replaced if either damage or improper
operation is noted.

For proper care of soiled safety belts, see Cleaning the Interior in the
Vehicle Care chapter.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

42 Personal Safety System

PERSONAL SAFETY SYSTEM™

The Personal Safety System provides an improved overall level of frontal
crash protection to front seat occupants and is designed to help further
reduce the risk of airbag-related injuries. The system is able to analyze
different occupant conditions and crash severity before activating the
appropriate safety devices to help better protect a range of occupants
in a variety of frontal crash situations.

Your vehicle’s Personal Safety System consists of:

• Driver and passenger dual-stage airbag supplemental restraints.

• Front outboard safety belts with pretensioners, energy management

retractors (first row only), and safety belt usage sensors.

• Driver’s seat position sensor.

• Front passenger sensing system.

• Passenger airbag off and on indicator lamp.

• Front crash severity sensors.

• Restraints control module with impact and safing sensors.

• Restraint system warning light and backup tone.

• The electrical wiring for the airbags, crash sensor(s), safety belt

pretensioners, front safety belt usage sensors, driver seat position
sensor, front passenger sensing system, and indicator lights.

How Does the Personal Safety System Work?

The Personal Safety System can adapt the deployment strategy of
your vehicle’s safety devices according to crash severity and occupant
conditions. A collection of crash and occupant sensors provides
information to the restraints control module. During a crash, the
restraints control module may activate the safety belt pretensioners
and/or either one or both stages of the dual-stage airbag supplemental
restraints based on crash severity and occupant conditions.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Supplementary Restraints System 43

PRINCIPLES OF OPERATION

WARNING: Airbags do not inflate slowly or gently, and the risk
of injury from a deploying airbag is the greatest close to the trim

covering the airbag module.

WARNING: All occupants of your vehicle, including the driver,
should always properly wear their safety belts, even when an

airbag supplemental restraint system is provided.

WARNING: Always transport children 12 years old and under
in the back seat and always properly use appropriate child

restraints.

WARNING: Never place your arm over the airbag module as a
deploying airbag can result in serious arm fractures or other

injuries.

WARNING: Airbags can kill or injure a child in a child seat.

NEVER place a rear-facing child seat in front of an active airbag.
If you must use a forward-facing child seat in the front seat, move the
seat all the way back.

WARNING: Do not attempt to service, repair, or modify the

airbag supplemental restraint systems or its fuses. Contact your
authorized dealer as soon as possible.

WARNING: Several airbag system components get hot after

inflation. Do not touch them after inflation.

WARNING: If the airbag has deployed, the airbag will not

function again and must be replaced immediately. If the airbag is
not replaced, the unrepaired area will increase the risk of injury in a
crash.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

44 Supplementary Restraints System

The airbags are a supplemental restraint system and are designed to
work with the safety belts to help protect the driver and right front
passenger from certain upper body injuries. Airbags do not inflate slowly;
there is a risk of injury from a deploying airbag.

Note: You will hear a loud bang and see a cloud of harmless powdery
residue if an airbag deploys. This is normal.

The airbags inflate and deflate rapidly upon activation. After airbag
deployment, it is normal to notice a smoke-like, powdery residue or smell
the burnt propellant. This may consist of cornstarch, talcum powder
(to lubricate the bag) or sodium compounds (for example, baking soda)
that result from the combustion process that inflates the airbag. Small
amounts of sodium hydroxide may be present which may irritate the skin
and eyes, but none of the residue is toxic. While the system is designed
to help reduce serious injuries, contact with a deploying airbag may also
cause abrasions or swelling. Temporary hearing loss is also a possibility
as a result of the noise associated with a deploying airbag. Because
airbags must inflate rapidly and with considerable force, there is the
risk of death or serious injuries, such as fractures, facial and eye injuries
or internal injuries, particularly to occupants who are not properly
restrained or are otherwise out of position at the time of airbag
deployment. Thus, it is extremely important that occupants be properly
restrained as far away from the airbag module as possible while
maintaining vehicle control.

Routine maintenance of the airbags is not required.

SOS POST-CRASH ALERT SYSTEM™

The system flashes the turn signal lamps and sounds the horn
(intermittently) in the event of a serious impact that deploys an airbag
equipped on your vehicle, such as front, side, side curtain or Safety
Canopy®.

The horn and lamps will turn off when:

• the hazard control button is pressed

• the panic button (if equipped) is pressed on the remote entry

transmitter, or

• your vehicle runs out of power.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Supplementary Restraints System 45

DRIVER AND PASSENGER AIRBAGS

WARNING: Never place your arm or any objects over an airbag

module. Placing your arm over a deploying airbag can result in
serious arm fractures or other injuries. Objects placed on or over the
airbag inflation area may cause those objects to be propelled by the
airbag into your face and torso causing serious injury.

WARNING: Airbags can kill or injure a child in a child seat.

Never place a rear-facing child seat in front of an active airbag.
If you must use a forward-facing child seat in the front seat, move the
seat all the way back.

The driver and front passenger
airbags will deploy during significant
frontal and near-frontal crashes.

The driver and passenger front airbag system consists of:

• driver and passenger airbag modules

• crash sensors and monitoring system with readiness

indicator. See Crash Sensors and Airbag Indicator
later in this chapter.

• front passenger sensing system

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

46 Supplementary Restraints System

Proper Driver and Front Passenger Seating Adjustment

WARNING:

recommends a minimum distance of at least 10 inches
(25 centimeters) between an occupant’s chest and the driver
airbag module.

To properly position yourself away from the airbag:

• Move your seat to the rear as far as you can while still reaching the
pedals comfortably.

• Recline the seat slightly (one or two degrees) from the upright
position.

After all occupants have adjusted their seats and put on safety belts,
it is very important that they continue to sit properly. Properly seated
occupants sit upright, lean against the seat back, and center themselves
on the seat cushion, with their feet comfortably extended on the floor.
Sitting improperly can increase the chance of injury in a crash event. For
example, if an occupant slouches, lies down, turns sideways, sits forward,
leans forward or sideways, or puts one or both feet up, the chance of
injury during a crash is greatly increased.

Children and Airbags

WARNING: Airbags can kill or injure a child in a child seat.

NEVER place a rear-facing child seat in front of an active airbag.
If you must use a forward-facing child seat in the front seat, move the
seat all the way back.

The National Highway Traffic Safety Administration

Children must always be properly
restrained. Accident statistics
suggest that children are safer
when properly restrained in the
rear seating positions than in the
front seating position. Failure to
follow these instructions may
increase the risk of injury in a
crash.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Supplementary Restraints System 47

FRONT PASSENGER SENSING SYSTEM

WARNING:

and under should be properly restrained in a rear seating position.

Failure to follow this could seriously increase the risk of injury or death.

WARNING: Sitting improperly out of position or with the seat

back reclined too far can take off weight from the seat cushion
and affect the decision of the front passenger sensing system, resulting
in serious injury or death in a crash.
Always sit upright against your seat back, with your feet on the floor.

WARNING: To reduce the risk of possible serious injury:

Do not stow objects in seat back map pocket or hang objects off
seat back if a child is in the front passenger seat.
Do not place objects underneath the front passenger seat or between
the seat and the center console.
Check the passenger airbag off or pass airbag off indicator lamp for
proper airbag status.
Failure to follow these instructions may interfere with the passenger
seat sensing system.

WARNING: Any alteration or modification to the front passenger

seat may affect the performance of the front passenger sensing
system which could seriously increase the risk of injury or death.

This system works with sensors that are part of the front passenger’s
seat and safety belt to detect the presence of a properly-seated occupant
and determine if the front passenger’s frontal airbag should be enabled
(may inflate) or not.

Even with Advanced Restraints Systems, children 12

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

48 Supplementary Restraints System

The front passenger sensing system
uses a passenger airbag status
indicator which will illuminate
indicating that the front passenger
frontal airbag is either ON (enabled)
or OFF (disabled). The indicator
lamp is located in the center stack
of the instrument panel.

Note: The passenger airbag status indicator OFF and ON lamps will
illuminate for a short period of time when the ignition is first turned on
to confirm it is functional.

The front passenger sensing system is designed to disable (will not
inflate) the front passenger’s frontal airbag when the front passenger
seat is unoccupied, or a rear facing infant seat, a forward-facing child
restraint, or a booster seat is detected. Even with this technology,
parents are STRONGLY encouraged to always properly restrain children
in the rear seat. The sensor also turns off the passenger front airbag and
seat-mounted side airbag when the passenger seat is empty.

• When the front passenger sensing system disables (will not inflate)
the front passenger frontal airbag, the passenger airbag status
indicator will illuminate the OFF lamp and stay lit to remind
you that the front passenger frontal airbag is disabled.

• If the child restraint has been installed and the passenger airbag
status indicator illuminates the ON lamp, then turn the vehicle off,
remove the child restraint from the vehicle and reinstall the restraint
following the child restraint manufacturer’s instructions.

The front passenger sensing system is designed to enable (may inflate)
the front passenger’s frontal airbag anytime the system senses that a
person of adult size is sitting properly in the front passenger seat.

• When the front passenger sensing system enables the front passenger
frontal airbag (may inflate), the passenger airbag status indicator will
illuminate the ON lamp and remain illuminated.

If a person of adult size is sitting in the front passenger’s seat, but the
passenger airbag status indicator OFF lamp is lit, it is possible that the
person isn’t sitting properly in the seat. If this happens:

• Turn the vehicle off and ask the person to place the seat back in the
full upright position.

• Have the person sit upright in the seat, centered on the seat cushion,
with the person’s legs comfortably extended.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Supplementary Restraints System 49

• Restart the vehicle and have the person remain in this position for
about two minutes. This will allow the system to detect that person
and enable the passenger’s frontal airbag.

• If the passenger airbag status indicator OFF lamp remains lit even
after this, the person should be advised to ride in the rear seat.

Occupant

Empty Unlit Disabled

Child Lit Disabled
Adult Unlit Enabled

Note: When the passenger airbag status indicator OFF lamp is
illuminated, the passenger side airbag (seat mounted) may be disabled
to avoid the risk of airbag deployment injuries.

After all occupants have adjusted their seats and put on safety belts,
it’s very important that they continue to sit properly. A properly seated
occupant sits upright, leaning against the seat back, and centered on
the seat cushion, with their feet comfortably extended on the floor.
Sitting improperly can increase the chance of injury in a crash event.
For example, if an occupant slouches, lies down, turns sideways, sits
forward, leans forward or sideways, or puts one or both feet up, the
chance of injury during a crash is greatly increased.

If you think that the state of the passenger airbag status indicator lamp
is incorrect, check for the following:

• Objects lodged underneath the seat

• Objects between the seat cushion and the center console

• Objects hanging off the seat back

• Objects stowed in the seat back map pocket

• Objects placed on the occupant’s lap

• Cargo interference with the seat

• Other passengers pushing or pulling on the seat

• Rear passenger feet and knees resting or pushing on the seat

Passenger Airbag

Status Indicator

Passenger Airbag

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

50 Supplementary Restraints System

The conditions listed above may cause the weight of a properly seated
occupant to be incorrectly interpreted by the front passenger sensing
system. The person in the front passenger seat may appear heavier or
lighter due to the conditions described in the previous list.

To know if the front passenger sensing system is operating
properly, see Crash Sensors and Airbag Indicator later in this

chapter.
If the airbag readiness light is lit, do the following:
The driver and adult passengers should check for any objects that may

be lodged underneath the front passenger seat or cargo interfering with
the seat.

If objects are lodged or cargo is interfering with the seat; please take the
following steps to remove the obstruction:

• Pull the vehicle over.

• Turn the vehicle off.

• Driver and adult passengers should check for any objects lodged

underneath the front passenger seat or cargo interfering with the seat.

• Remove the obstruction(s) (if found).

• Restart the vehicle.

• Wait at least two minutes and verify that the airbag readiness light in

the instrument cluster is no longer illuminated.

• If the airbag readiness light in the instrument cluster remains

illuminated, this may or may not be a problem due to the front
passenger sensing system.

Do not attempt to repair or service the system. Take your vehicle
immediately to an authorized dealer.

If it is necessary to modify an advanced front airbag system to
accommodate a person with disabilities, contact the Ford Customer
Relationship Center at the phone number shown in the Customer
Assistance section of this owner’s manual.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Supplementary Restraints System 51

SIDE AIRBAGS

WARNING:

the airbag cover, on the side of the seat backs (of the front seats),
or in front seat areas that may come into contact with a deploying
airbag. Failure to follow these instructions may increase the risk of
personal injury in the event of a crash.

WARNING: Do not use accessory seat covers. The use of

accessory seat covers may prevent the deployment of the side
airbags and increase the risk of injury in an accident.

WARNING: Do not lean your head on the door. The side airbag

could injure you as it deploys from the side of the seat back.

WARNING: Do not attempt to service, repair, or modify the

airbag, its fuses or the seat cover on a seat containing an airbag
as you could be seriously injured or killed. Contact your authorized
dealer as soon as possible.

WARNING: If the side airbag has deployed, the airbag will not

function again. The side airbag system (including the seat) must
be inspected and serviced by an authorized dealer. If the airbag is not
replaced, the unrepaired area will increase the risk of injury in a crash.

The side airbags are located on the outboard side of the seat backs of
the front seats. In certain lateral crashes, the airbag on the side affected
by the crash will be inflated. The airbag was designed to inflate between
the door panel and occupant to further enhance the protection provided
occupants in side impact crashes.

Do not place objects or mount equipment on or near

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

52 Supplementary Restraints System

The system consists of the
following:

• a tag on the seat back indicating
that side airbags are found on
your vehicle

• side airbags located inside the
seat back of the driver and front
passenger seats.

• crash sensors and monitoring system with readiness
indicator. See Crash Sensors and Airbag Indicator later
in this chapter.

• front passenger sensing system.
Note: The passenger sensing system will deactivate the passenger

seat-mounted side airbag if it detects an empty, unbuckled passenger
seat.

The design and development of the side airbag system included
recommended testing procedures that were developed by a group of
automotive safety experts known as the Side Airbag Technical Working
Group. These recommended testing procedures help reduce the risk of
injuries related to the deployment of side airbags.

SAFETY CANOPY® CURTAIN AIRBAGS

WARNING: Do not place objects or mount equipment on or near

the headliner at the siderail that may come into contact with a
deploying curtain airbag. Failure to follow these instructions may
increase the risk of personal injury in the event of a crash.

WARNING: Do not lean your head on the door. The curtain

airbag could injure you as it deploys from the headliner.

WARNING: Do not attempt to service, repair, or modify the

curtain airbags, its fuses, the A, B, C or D pillar trim, or the
headliner on a vehicle containing curtain airbags as you could be
seriously injured or killed. Contact your authorized dealer as soon
as possible.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Supplementary Restraints System 53

WARNING:

should always wear their safety belts even when an airbag
supplemental restraint system and curtain airbag is provided. Failure to
properly wear your safety belt could seriously increase the risk of injury
or death.

WARNING: To reduce risk of injury, do not obstruct or place

objects in the deployment path of the curtain airbag.

WARNING: If the curtain airbags have deployed, the curtain

airbags will not function again. The curtain airbags (including the
A, B, C or D pillar trim and headliner) must be inspected and serviced
by an authorized dealer. If the curtain airbag is not replaced, the
unrepaired area will increase the risk of injury in a crash.

The Safety Canopy will deploy during significant side crashes or when a
certain likelihood of a rollover event is detected by the rollover sensor.
The Safety Canopy is mounted to the roof side-rail sheet metal, behind
the headliner, above each row of seats. In certain lateral crashes or
rollover events, the Safety Canopy will be activated, regardless of which
seats are occupied. The Safety Canopy is designed to inflate between the
side window area and occupants to further enhance protection provided
in side impact crashes and rollover events.

All occupants of your vehicle including the driver

The system consists of:

• safety canopy curtain airbags
fitted above the trim panels over
the front and rear side windows
identified by a label or wording
on the headliner or roof-pillar
trim.

• a flexible headliner which opens above the side doors to allow air
curtain deployment.

• crash sensors and monitoring system with readiness
indicator. See Crash Sensors and Airbag Indicator in
this chapter.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

54 Supplementary Restraints System

Children 12 years old and under should always be properly restrained
in the rear seats. The Safety Canopy will not interfere with children
restrained using a properly installed child or booster seat because it is
designed to inflate downward from the headliner above the doors along
the side window opening.

The design and development of the Safety Canopy included
recommended testing procedures that were developed by a group of
automotive safety experts known as the Side Airbag Technical Working
Group. These recommended testing procedures help reduce the risk of
injuries related to the deployment of side airbags (including the Safety
Canopy).

CRASH SENSORS AND AIRBAG INDICATOR

WARNING: Modifying or adding equipment to the front end of

your vehicle (including frame, bumper, front end body structure
and tow hooks) may affect the performance of the airbag system,
increasing the risk of injury. Do not modify the front end of your
vehicle.

Your vehicle has a collection of crash and occupant sensors which
provide information to the restraints control module which deploys
(activates) the front safety belt pretensioners, driver airbag, passenger
airbag, seat mounted side airbags, and the Safety Canopy®. Based on the
type of accident (frontal impact, side impact or rollover) the restraints
control module will deploy the appropriate safety devices.

The restraints control module also monitors the readiness of the above
safety devices plus the crash and occupant sensors. The readiness of the
safety system is indicated by a warning indicator light in the instrument
cluster or by a backup tone if the warning light is not working. See the
Instrument Cluster chapter. Routine maintenance of the airbag is not
required.

A difficulty with the system is indicated by one or more of the following:

• The readiness light will either flash or stay lit.

• The readiness light will not illuminate immediately after the

ignition is turned on.

• A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem or light are repaired.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Supplementary Restraints System 55

If any of these things happen, even intermittently, have the supplemental
restraint system serviced at an authorized dealer immediately. Unless
serviced, the system may not function properly in the event of a crash.

The safety belt pretensioners and the airbag supplemental restraint
system are designed to activate when the vehicle sustains longitudinal or
lateral deceleration sufficient to cause the restraints control module to
deploy a safety device or when a certain likelihood of a rollover event is
detected by the rollover sensor.

The fact that the safety belt pretensioners or airbags did not activate for
both front seat occupants in a crash does not mean that something is
wrong with the system. Rather, it means the restraints control module
determined the accident conditions (such as crash severity, belt usage)
were not appropriate to activate these safety devices.

• Front airbags are designed to activate only in frontal and near-frontal
crashes (not rollovers, side impacts or rear impacts) unless the crash
causes sufficient longitudinal deceleration.

• The safety belt pretensioners are designed to activate in frontal,
near-frontal and side crashes, and in rollovers.

• Side airbags are designed to inflate in side-impact crashes, not
rollovers, rear impacts, frontal or near-frontal crashes, unless the
crash causes sufficient lateral deceleration.

• The Safety Canopy is designed to inflate in certain side impact crashes
or rollover events, not in rear impact, frontal or near-frontal crashes,
unless the crash causes sufficient lateral deceleration or rollover
likelihood.

AIRBAG DISPOSAL

Contact your authorized dealer as soon as possible. Airbags MUST BE
disposed of by qualified personnel.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

56 Keys and Remote Control

PRINCIPLE OF OPERATION

The remote control allows you to:

• remotely lock or unlock the vehicle doors

• remotely open the power liftgate

• remotely start or stop the engine

• arm and disarm the anti-theft system

• activate the panic alarm

• activate the global open windows.

Intelligent Access

Your vehicle will allow you to unlock and enter your vehicle without
actively using a key or remote control. You can use this feature at the
front doors or at the liftgate or trunk. You can activate the intelligent
access feature as long as you have one of your intelligent access keys
within range of the front doors or the liftgate or trunk.

GENERAL INFORMATION ON RADIO FREQUENCIES

This device complies with part 15 of the FCC Rules and with Industry
Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.

Note: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment. The term IC before the radio certification number only
signifies that Industry Canada technical specifications were met.

The typical operating range for your transmitter is approximately 33 feet
(10 meters). Vehicles with the remote start feature will have a greater
range. A decrease in operating range could be caused by:

• weather conditions

• nearby radio towers

• structures around your vehicle

• other vehicles parked next to your vehicle.

The radio frequency used by your remote control can also be used by
other short-distance radio transmissions, for example amateur radios,
medical equipment, wireless headphones, remote controls and alarm
systems. If the frequencies are jammed, you will not be able to use
your remote control. You can lock and unlock the doors with the key.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Keys and Remote Control 57

Note: Make sure your vehicle is locked before leaving it unattended.

Note: If you are in range, the remote control will operate if you press

any button unintentionally.

Intelligent Access

The system uses a radio frequency signal to communicate with your
vehicle and authorize your vehicle to unlock when one of the following
conditions is met:

• You touch the inside of the front exterior door handle.

• You press the luggage compartment button.

• You press a button on the transmitter.

If excessive radio frequency interference is present in the area or if the
transmitter battery is low, it may be necessary to mechanically unlock
your door. You can use the mechanical key blade in your intelligent
access key to open the driver door in this situation. Refer to Remote
Control in this chapter for more information on the location and use
of the mechanical key blade.

REMOTE CONTROL

Intelligent Access Key

Your vehicle is equipped with
two intelligent access keys which
operate the power locks and the
remote start system. The key must
be in the vehicle to activate the
push button start system.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

The intelligent access key also
contains a removable mechanical key
blade that can be used to unlock the
driver door. Slide the release on the
back of the transmitter to release the
mechanical key blade, then pull the
blade out.

58 Keys and Remote Control

Note: Your vehicle’s back-up keys
were issued with a security tag that
provides important vehicle key cut
information. Keep the tag in a safe
place for future reference.

Replacing the Battery

Note: Refer to local regulations when disposing of transmitter batteries.
Note: Do not wipe off any grease on the battery terminals or on the

back surface of the circuit board.
Note: Replacing the battery will not delete the transmitter from the

vehicle. The transmitter should operate normally.
The remote control uses one coin-type three-volt lithium battery CR2032

or equivalent.

Intelligent Access Transmitter

1. Remove the backup key from the transmitter.

2. Twist a thin coin under the tab
hidden behind the backup key head
to remove the battery cover. Do not
use the backup key to remove the
cover or you could damage the
intelligent access key.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

3. Remove the old battery.

Keys and Remote Control 59

4. Insert a new battery with the + facing downward. Press the battery

down to make sure it is fully in the housing.

5. Snap the battery cover back onto the transmitter and install the

backup key.

Memory Feature

This feature allows you to recall the driver seat, power mirrors and
power steering column memory positions.

Press the unlock button on the remote control or activate intelligent
access to recall memory. The seat, power mirrors and steering column
automatically move to the memory position. The mirrors will move to the
programmed position and the seat will move to the easy entry position.
The seat will move to the final position when the ignition is switched out
of off (if easy entry feature is enabled).

Programming Memory to the Transmitter

To activate this feature:

1. Move the memory features to the desired positions using the

associated controls.

2. Press and hold button 1 for five seconds. A tone will

1

sound confirming memory position has been set. Continue
to hold until a second tone is heard after five seconds.

2

3. Within three seconds press the lock button on the remote control.

4. Wait 10 seconds, then press the unlock button on the remote control.

5. Repeat this procedure for memory button 2 and another transmitter if

desired.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

60 Keys and Remote Control

Deactivating Memory from the Transmitter

To deactivate this feature:

1. Press and hold either the 1 or 2 button for five seconds. A tone will
sound when the memory store is done. Continue to hold until a second
tone is heard.

2. Within three seconds press the unlock button on the remote control.

3. Repeat this procedure for each additional transmitter if desired.

Car Finder

Press the button twice within three seconds. The horn will sound
and the turn signals will flash. We recommend you use this
method to locate your vehicle, rather than using the panic alarm.

Sounding a Panic Alarm

Press the button to activate the alarm. Press the button again
or switch the ignition on to deactivate.

Note: The panic alarm will only operate when the ignition is off.

Remote Start

WARNING:

your vehicle is parked indoors or areas that are not well ventilated.

Note: Do not use remote start if your vehicle is low on fuel.

Your vehicle has remote start if the transmitter has this button.

The remote start feature allows you to start your vehicle from outside
your vehicle. The transmitter has an extended operating range.

Vehicles with automatic climate control can be configured to operate
when the vehicle is remote started. See the Climate Control chapter for
more information. A manual climate control system will run at the setting
it was set to when your vehicle was last turned off.

Many states and provinces have restrictions for the use of remote start.
Check your local and state or provincial laws for specific requirements
regarding remote start systems.

To avoid exhaust fumes, do not use remote start if

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Keys and Remote Control 61

The remote start system will not work if:

• the ignition is on

• the alarm system is triggered

• you disable the feature

• the hood is not closed

• the transmission is not in P

• the vehicle battery voltage is too low

• the service engine soon light is on.

Remote Starting the Vehicle

Note: You must press each button within three seconds of each other.
Your vehicle will not remote start and the horn will not chirp if you do
not follow this sequence.

The label on your transmitter
details the starting procedure.
To remote start your vehicle:

1. Press the lock button to lock all the doors.

2. Press the remote start button twice. The exterior lamps will flash

twice.
The horn will chirp if the system fails to start, unless quiet start is on.

Quiet start will run the blower fan at a slower speed to reduce noise. You
can switch it on or off in the information display. See the Information
Displays chapter.

Note: If you remote start your vehicle you must have a programmed
intelligent access key inside your vehicle and press the START/STOP
button on the instrument panel once while applying the brake pedal
before driving your vehicle.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

62 Keys and Remote Control

The power windows will be inhibited during the remote start and the
radio will not turn on automatically.

The parking lamps will remain on and your vehicle will run for 5, 10, or
15 minutes, depending on the setting. See the Information Displays
chapter to select the duration of the remote start system.

Extending the Vehicle Run Time

Repeat Steps 1 and 2 with your vehicle still running to extend the run
time for another remote start duration. If the duration is set to last
10 minutes, the duration will extend by another 10 minutes beginning
after what is left of the first activation time. For example, if your vehicle
had been running from the first remote start for five minutes, your
vehicle will continue to run now for a total of 15 minutes.

Wait at least five seconds before remote starting after a vehicle
shutdown.

Turning the Vehicle Off After Remote Starting

Press the button once. The parking lamps will turn off.

You may have to be closer to your vehicle than when starting due to
ground reflection and the added noise of the running vehicle.

You can disable or enable the remote start system through the
information display. Refer to the Information Display chapter.

REPLACING A LOST KEY OR REMOTE CONTROL

You can purchase replacement or additional keys or remote controls
from an authorized dealer. A dealer can program the transmitters to your
vehicle or you may be able to program them yourself. See the Security
chapter for information on programming your transmitters.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

MyKey 63

PRINCIPLES OF OPERATION

MyKey® allows you to program keys with restricted driving modes to
promote good driving habits. All but one of the keys programmed to the
vehicle can be activated with these restricted modes. Any keys that have
not been programmed are referred to as an administrator key or admin
key which can be used to:

• create a restricted key

• program optional MyKey settings

• clear all MyKey features altogether.

Once a key has been programmed, you can access the following
information using the information display control:

• How many admin keys and MyKeys are programmed to the vehicle.

• The total distance the vehicle has been driven with a MyKey.

For vehicles equipped with intelligent access (push button start), when
both a MyKey and an admin intelligent access key (fob) are present, the
admin fob will be recognized by the vehicle to start the engine.

Standard Settings

These settings cannot be changed.

• Belt-Minder. This cannot be disabled and the five-minute timer does
not expire. The audio system is muted when MyKey Belt-Minder is
activated.

• Early low fuel. Warnings are displayed in the information display
control followed by an audible tone when the fuel tank is at 1/8 tank
or less.

• Driver assist features, if equipped on your vehicle, are forced on: rear
parking aid, BLIS® (Blind Spot Information System) with cross-traffic
alert, lane departure warning, forward collision warning system and
satellite radio adult content restriction.

Optional Settings

These settings can be configured right after a MyKey is first created or
changed afterward with an admin key.

• Vehicle speed limit of 65, 70, 75 and 80 mph (105, 113, 121 and
130 km/h). Visual warnings are displayed followed by an audible
tone when vehicle speed has reached the selected top speed.

• Vehicle speed minder of 45, 55 or 65 mph (75, 90, or 105 km/h).
Visual warnings are displayed followed by an audible tone when the
preselected vehicle speed is exceeded.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

64 MyKey

• Audio system maximum volume of 45%. A message in the audio
system is displayed when attempting to exceed the limited volume.
Also, the speed sensitive compensated volume feature will be disabled.

• Always on setting. When this is selected, you will not be able to
disable AdvanceTrac, 911 Assist or Do not disturb feature (if your
vehicle is equipped with these features).

CREATING A MYKEY

Use the information display control to create a MyKey.

1. Insert the key you want to program into the ignition or, if the vehicle

is equipped with push button start, put the Intelligent Access key in
the backup slot; see the Starting and Stopping the Engine chapter
for the backup slot location.

2. Turn the ignition on.

3. Access the main menu from the information display controls and

select Settings, then MyKey by pressing OK or the > button.

4. Press OK to select Create.

5. When prompted, hold the OK button until you see a message

informing you to label this key as a MyKey. The key will be restricted
at the next start.

The key is successfully programmed. Make sure you label it so you can
distinguish it from the admin keys.

To program optional settings for the key(s), see the
Programming/Changing Optional Settings chapter.

Programming/Changing Optional Settings

Note: All programmed keys can be cleared within the same key cycle in
which a key was programmed, otherwise an admin key is required to
clear the keys. To clear all keys, refer to Clearing all MyKeys.

You can access the optional settings through the information display
control.

1. Turn the ignition on using an admin key.

2. Access the main menu and select Settings, then MyKey.

3. Use the arrow buttons to get to an optional feature.

4. Press OK or > to scroll through settings.

5. Press OK or > to make a selection.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

MyKey 65

CLEARING ALL MYKEYS

Note: All programmed MyKeys can be cleared within the same key cycle
in which a MyKey was created, otherwise an admin key is required to
clear the keys.

To clear all MyKeys (which removes all restrictions and returns them
to admin key status), use the information display controls to do the
following:

1. Access the main menu and select Settings, then MyKey.

2. Scroll to Clear All and press the OK button.

3. Hold the OK button until ALL MYKEYS CLEARED is displayed.

CHECKING MYKEY SYSTEM STATUS

The information display controls provide information about keys
programmed to the vehicle:

• MYKEY MILES: Tracks mileage when a MyKey is used. If mileage
does not accumulate as expected, then the MyKey is not being used
by the intended user. The only way to reset this to zero is by clearing
MyKeys. If the mileage is lower than the last time you checked, then
the key system has been recently reset.

• # MYKEY(S): Indicates how many MyKeys are programmed to the
vehicle. Can also be used to detect deletion of a MyKey.

• # ADMIN KEY(S): Indicates how many admin keys are programmed
to the vehicle. Can also be used to detect if an additional key has
been programmed to the vehicle.

USING MYKEY WITH REMOTE START SYSTEMS

MyKey is NOT compatible with non-Ford-approved aftermarket remote
start systems. If you choose to install a remote start system, please see
your Ford authorized dealer for a Ford-approved remote start system.

The following information MAY help customers who choose to use a
non-Ford-approved remote start system. The actions provided below do
NOT make MyKey compatible with non-Ford-approved remote start
system, but it MAY help you to retain some MyKey functions.

Vehicles Equipped with Traditional Keys

When using a non-Ford-approved remote start system, the default
settings may recognize the remote start system as an additional admin
key with its associated privileges. It is NOT compatible with MyKey.
Restart the engine when you insert a key into the ignition cylinder; it
may help you to retain some MyKey functions.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

66 MyKey

In addition to the key that has been programmed as a MyKey, owners of
vehicles equipped with traditional keys have the option to program the
non-Ford-approved remote start system as a MyKey if the remote start
fob is used by the MyKey driver.

To program a non-Ford-approved remote start system as a MyKey, do the
following:

1. Enter the vehicle and close all doors.

2. Remote start the vehicle using a non-Ford approved remote start fob.

3. Follow Steps 1-5 in the Creating a MyKey section.

Vehicles Equipped with Intelligent Access Key (Push Button Start)

Note: It is not possible to program the remote start system as a MyKey
on vehicles equipped with intelligent access key (push button start).
Therefore, you should treat the remote start fob as you would any other
admin key. When the vehicle is started using remote start, the system
will stall the engine when you either enter the vehicle or shift the vehicle
into gear. Prior to the engine stall, the vehicle will have administrative
privileges. When you restart the engine, the vehicle will identify the user
as an admin or MyKey driver depending on the settings of the actual key
used to start the vehicle.

Note: For all vehicles, the number of MYKEY(S) PROGRAMMED or
ADMIN KEYS PROGRAMMED that is displayed in the MyKey system
status menu, may include the non-Ford-approved remote start system as
an additional key in the total count. See the Checking System Status
section.

For all vehicles with a non-Ford-approved remote start installed, it is
possible to program all real keys as MyKeys, in which case, you will need
to use your remote start system to clear all MyKeys (which removes
all restrictions and returns them to admin key status) by doing the
following:

1. Enter the vehicle and close all doors.

2. Remote start the vehicle using your non-Ford-approved remote
start fob.

3. Follow Steps 1-3 in the Clearing all MyKeys section.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

MyKey 67

MYKEY TROUBLESHOOTING

Condition Potential Causes

I cannot program a
key.

I cannot program the
optional settings.

I cannot clear the
restricted keys.

• The key in the ignition does not have admin
privileges.

The key in the ignition is the only admin key

•

(there always has to be at least one admin key).

• The intelligent access key is not in the backup
slot (vehicles with push button start).

• SecuriLock passive anti-theft system is
disabled or in unlimited mode.

• The vehicle has been started using a remote
start system that is not programmed with admin
privileges. See the Using MyKey with Remote
Start Systems chapter.

• The key in the ignition does not have admin
privileges.

• No keys are programmed to the vehicle. See
the Creating a MyKey chapter.

• The vehicle has been started using a remote
start system that is not programmed with
admin privileges. See the Using MyKey with
Remote Start System chapter.

• Key in the ignition does not have admin
privileges.

• No restricted keys are programmed to the
vehicle. See the Creating a MyKey chapter.

• The vehicle has been started using a remote
start system that is not programmed with
admin privileges. See the Using MyKey with
Remote Start System chapter.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

68 MyKey

Condition Potential Causes

I lost the only admin
key.

I lost a key. • Program spare keys as outlined under

I accidentally
programmed all keys
as restricted keys.

No restricted key
functions with
intelligent access key
(push button start).

Restricted key
programmed total
includes one additional
key.

Admin keys
programmed total
includes one additional
key.

MyKey miles do not
accumulate.

• Purchase a new key from your authorized
dealer.

SecuriLock in the Security chapter.

• The vehicle has a remote start system that
is recognized as an admin key. See the Using
MyKey with Remote Start System chapter to
reset all restricted keys using remote start.

• An admin key is present at engine start-up.

• No restricted keys are programmed to the

vehicle. See the Creating a MyKey chapter.

• An unknown key has been programmed to
the vehicle as a restricted key.

• The vehicle is equipped with a remote start
system. See the Using MyKey with Remote
Start Systems chapter.

• An unknown key has been programmed to
the vehicle as an admin key.

• Vehicle is equipped with a remote start
system. See the Using MyKey with remote
start systems chapter.

• The restricted key is not being used by the
intended user.

• The key system has been reset.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Locks 69

LOCKING AND UNLOCKING

You can use the power door lock control or the remote control to lock
and unlock the vehicle.

Power Door Locks

The power door lock control is located on the driver and front passenger
door panels.

A. Unlock

A

B

Remote Control

You can use the remote control anytime the vehicle is not running.

Unlocking the Doors (Two-Stage Unlock)

Press and hold both the lock and unlock buttons on the remote control
for four seconds to disable or enable two-stage unlocking. Disabling
two-stage unlocking allows all vehicle doors to unlock with one press of
the button. The turn signals will flash twice to indicate the unlocking
mode was changed. The unlocking mode will be applied to the remote
control, keyless entry keypad and intelligent access.

Intelligent access at the driver door will unlock all doors when two-stage
unlocking is disabled.

Locking the Doors

B. Lock

Press the button to unlock the driver doors.
Press the button again within three seconds to unlock all doors.

The turn signals will flash.

Press the button to lock all the doors. The turn signals will
illuminate.

Press the button again within three seconds to confirm that all the doors
are closed. The doors will lock again, the horn will sound and the turn
signals will illuminate if all the doors and the luggage compartment are
closed.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

70 Locks

Note: If any door or the luggage compartment is open, or if the hood is
open on vehicles equipped with an anti-theft alarm or remote start, the
horn will sound twice and the lamps will not flash.

Power Liftgate

WARNING: Make sure all persons are clear of the liftgate area
before using power liftgate control.

WARNING: Make sure the liftgate is closed to prevent exhaust

fumes from being drawn into the vehicle. This will also prevent
passengers and cargo from falling out. If you must drive with the
liftgate open, keep the vents open so outside air comes into the vehicle.

Note: Be careful when opening or closing the liftgate in a garage or
other enclosed area to avoid damaging the liftgate.

Press twice within three seconds to open or close the liftgate,
or to reverse the movement.

Activating Intelligent Access

The intelligent access key must be within 3 feet (1 meter) of your vehicle.

At the Front Doors

Pull a front exterior door handle. The door will unlock and can be
opened.

Press and hold the door handle lock
sensor to lock your vehicle. To avoid
unlocking the door inadvertently, be
sure to only touch the lock sensor
and not other areas of the door
handle.

At the Liftgate

Press the exterior liftgate release button on the top of the liftgate
pull-cup handle.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Locks 71

Smart Unlocks

The smart unlock feature is intended to prevent you from unintentionally
locking your intelligent access key inside your vehicle’s passenger
compartment or rear cargo area.

When you lock your vehicle using the driver or passenger power door
lock control (with the door open, transmission is in P and ignition off),
after you close the door the vehicle will search for an intelligent access
key in the passenger compartment. If an intelligent access key is found
inside your vehicle, all of the doors will immediately unlock and the horn
will chirp, indicating that the intelligent access key is inside.

In order to override the smart unlock feature and intentionally lock the
intelligent access key inside your vehicle, you can lock your vehicle after
all doors are closed by using the keyless entry keypad, pressing the lock
button on another intelligent access key or touching the locking area on
the handle with another intelligent access key in your hand. Refer to
SecuriCode™ Keyless Entry Keypad in this chapter for more
information on keyless entry keypad operation.

When you open one of the front doors and lock your vehicle using the
power door lock control, all doors will lock then unlock if:

• the ignition is on, or

• the ignition is off and the transmission is not in P.

Autolock Feature (If Enabled)

The autolock feature will lock all the doors when:

• all the doors are closed,

• the ignition is on,

• you shift into any gear putting your vehicle in motion, and

• your vehicle reaches a speed greater than 12 mph (20 km/h).

The autolock feature repeats when:

• you open then close any door while the ignition is on and the vehicle
speed is 9 mph (15 km/h) or lower, and

• your vehicle then reaches a speed greater than 12 mph (20 km/h).

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

72 Locks

Autounlock Feature (If Enabled)

The autounlock feature will unlock all the doors when:

• the ignition is on, all the doors are closed, and your vehicle has been
in motion at a speed greater than 12 mph (20 km/h);

• your vehicle has then come to a stop and the ignition is switched off
or to accessory; and

• the driver door is opened within 10 minutes of the ignition being
switched off or to accessory.

Note: The doors will not autounlock if you electronically lock the vehicle
after you switch the ignition off and before you open the driver door.

Deactivating or Activating

Note: You can activate or deactivate the autolock and autounlock
features independently of each other.

You can activate or deactivate these features:

• through an authorized dealer

• using the information display.

Illuminated Entry

The interior lamps, parking lamps and puddle lamps (if equipped)
illuminate when you use the intelligent access key or the keyless entry
keypad to unlock your vehicle.

The system will turn off the lights if:

• you switch the ignition on

• you press the lock button on the remote control

• you lock the vehicle using the keyless entry keypad

• they have been on for 25 seconds.

The lights will not turn off if:

• you have turned them on with the dimmer control

• any door is open.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Locks 73

Illuminated Exit

The interior dome lamps, parking lamps and puddle lamps (if equipped)
illuminate when all doors are closed and the ignition is turned off.

The lights turn off if all the doors remain closed and:

• 25 seconds elapse

• you press the START/STOP button.

Battery Saver

If you leave the courtesy lamps, dome lamps or headlamps on, the
battery saver shuts them off 10 minutes after you switch the ignition off.

Accessory Mode Battery Saver for Intelligent Access Keys

If you shut off the engine and leave the ignition in the on or accessory
mode, the ignition will shut off after 30 minutes.

LIFTGATE

WARNING: It is extremely dangerous to ride in a cargo area,

inside or outside of a vehicle. In a crash, people riding in these
areas are more likely to be seriously injured or killed. Do not allow
people to ride in any area of your vehicle that is not equipped with
seats and safety belts. Be sure everyone in your vehicle is in a seat
and using a safety belt properly.

Power Liftgate

WARNING: Make sure all persons are clear of the power liftgate

area before using the power liftgate control.

WARNING: Keep keys out of the reach of children. Do not allow

children to operate the power liftgate, or to play near to an open
or moving power liftgate.

Note: Cycling the ignition while the liftgate is power closing and is
near the latch may cause the liftgate to reverse to full open position.
Make sure that the liftgate is closed before operating or moving the
vehicle, especially in an enclosure, like a garage or a parking structure.
The liftgate or its components could be damaged.

Note: Do not drive with the liftgate open without first disabling the
power function and securing the liftgate to the vehicle.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

74 Locks

Note: In case of operation in extreme cold -40°F (-40°C), or on extreme
inclines, manual operation of the liftgate is suggested.

You can enable or disable the power liftgate using the information
display. The remote control and instrument panel button will still operate
the liftgate regardless of the setting.

Opening and Closing the Power Liftgate

Note: The liftgate movement direction can be reversed with a second
press of the instrument panel, or the control button on the liftgate, or a
second double press of the transmitter button.

The liftgate will only operate with the vehicle in P.
A chime will sound three times as the liftgate begins to power close.

A single chime indicates a problem with the close request, caused by:

• the ignition is on and the transmission is not in P;

• or the battery voltage is below the minimum operating voltage;

• or the vehicle speed is at or above 3 mph (5 km/h).

If the liftgate reverses and starts to close after an open request, a fast
continuous chime indicates excessive load on the gate or a possible strut
failure. See your authorized dealer if you still have a fast chime after the
load is removed.

To open or close from the instrument panel: Press the
instrument panel button.

To open or close with the remote control: Press the remote
control button twice within three seconds.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

To open with the outside liftgate
control button:

Unlock the liftgate with the remote

1.
control or power door unlock control.
If the intelligent access transmitter
(if equipped) is within 3 feet (1 meter)
of the liftgate, the liftgate will unlock
when you press the liftgate release
button.

Locks 75

2. Press the control button located in the top of the liftgate pull-cup
handle.

Note: Allow the power system to open the liftgate after pressing the
control. Manually pushing or pulling the liftgate may activate the
system’s obstacle detection feature and stops the power operation.

To close with the rear cargo area control: Press and release
the button.

WARNING: Keep clear of the liftgate when activating the rear

switch.

Obstacle Detection

When closing: The system will reverse to full open when it detects an
obstacle. A chime will sound three times as the liftgate begins to reopen.
Remove the obstacle to close the liftgate.

Entering the vehicle while the liftgate is closing can cause the

Note:

vehicle to bounce and activate obstacle detection. To prevent this, allow
the power liftgate to fully close before entering the vehicle. Before driving
off, check the instrument cluster for a liftgate or door ajar message and/or
warning indicator. Driving off without first checking for the liftgate or door
ajar message and/or warning indicator could result in the liftgate being left
open, unintentionally, while you are driving.

When opening: The system will stop and a chime will sound three times
when it detects an obstacle. Remove the obstacle to operate the liftgate.

Resetting the Power Liftgate

The liftgate may not operate properly and may need to be reset if any of
these conditions occur:

• a low voltage or dead battery

• disconnected battery

• the liftgate is manually closed and left ajar (unlatched)

To reset the power liftgate:

1. Disconnect the battery for 20 seconds then, reconnect the battery.

2. Manually close and fully latch the liftgate.

3. Power open the liftgate by using the transmitter, or the instrument
panel control button.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

76 Locks

Manual Operation

WARNING: Make sure that the liftgate is closed to prevent

exhaust fumes from being drawn into the vehicle. This will also
prevent passengers and cargo from falling out. If you must drive with
the liftgate door open, keep the vehicle well ventilated so outside air
comes into the vehicle.

Note: Be careful when opening or closing the liftgate in a garage or
other enclosed area to avoid damaging the liftgate.

Note: Do not hang anything (bike rack, etc.) from the spoiler, glass or
liftgate. This could damage the liftgate and its components.

Note: Do not leave the liftgate open while driving. This could damage to
the liftgate and its components.

The liftgate area is only intended for cargo, not passengers.

To open the liftgate: Press the
button located in the top of the
liftgate pull cup handle to unlatch
the liftgate, then pull on the outside
handle.

If the liftgate is not fully latched, you will receive a message information
display. Check the liftgate door to make sure it is fully latched.

In the event of a power failure, the latch can be accessed and released
from the inside using the access panel on the liftgate trim.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Locks 77

SECURICODE™ KEYLESS ENTRY KEYPAD

You can use the keypad to:

• lock or unlock the doors

• recall memory features

• enable and disable autolock and autounlock

• program and erase user codes

• arm and disarm the anti-theft alarm.

The keypad can be operated with the factory-set 5-digit entry code;
this code is located on the owner’s wallet card in the glove box and is
available from your authorized dealer. You can also create up to five of
your own 5-digit personal entry codes.

Programming a Personal Entry Code

To create your own personal entry code:

1. Enter the factory-set code.

2. Press the 1•2 on the keypad within five seconds.

3. Enter your personal 5-digit code. You must enter each number within
five seconds of each other.

4. For memory recall feature, enter the sixth digit 1•2 to store driver 1
settings or 3•4 to store driver 2 settings.

Note: Pressing 5•6, 7•8,or9•0 keypad numbers as a sixth digit will
not recall a driver memory setting.

Note: The factory-set code cannot be associated with a memory setting.

5. The doors will lock and then unlock to confirm that programming is
complete.

You may also program a personal entry code through the MyFord Touch
or MyLincoln Touch system. Refer to the MyFord Touch or MyLincoln
Touch chapter.

Tips:

• Do not set a code that uses five of the same number.

• Do not use five numbers in sequential order.

• The factory-set code will work even if you have set your own personal

code.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

78 Locks

Erasing a Personal Code

1. Enter the factory-set 5-digit code.

2. Press and release the 1•2 on the keypad within five seconds.

3. Press and hold the 1•2 for two seconds. This must be done within
five seconds of completing Step 2.

All personal codes are now erased and only the factory-set 5-digit code
will work.

Anti-Scan Feature

The keypad will go into an anti-scan mode if you enter the wrong code
seven times (35 consecutive button presses). This mode disables the
keypad for one minute and the keypad lamp will flash.

The anti-scan feature will turn off after:

• one minute of keypad inactivity

• pressing the unlock button on the remote control

• the ignition is turned on

• unlocking the vehicle using intelligent access.

Unlocking and Locking the Doors

To unlock the driver door: Enter the factory-set 5-digit code or your
personal code. You must press each number within five seconds of each
other. The interior lamps will illuminate. Note: All doors will unlock if
the two-stage unlocking feature is disabled. Refer to Locking and
Unlocking earlier in this chapter.

To unlock all doors: Enter the factory-set code or your personal code,
then press the 3•4 control within five seconds.

To lock all doors: Press and hold 7• 8 and 9•0 at the same time with
the driver door closed. You do not need to enter the keypad code first.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Security 79

SECURILOCK® PASSIVE ANTI-THEFT SYSTEM

Note: The system is not compatible with non-Ford aftermarket remote
start systems. Use of these systems may result in vehicle starting
problems and a loss of security protection.

Note: Metallic objects, electronic devices or a second coded key on the
same key chain may cause vehicle starting issues if they are too close to
the key when starting the engine. Prevent these objects from touching
the coded key while starting the engine. Switch the ignition off, move all
objects on the key chain away from the coded key and restart the engine
if a problem occurs.

Note: Do not leave a duplicate coded key in the vehicle. Always take
your keys and lock all doors when leaving the vehicle.

The system is an engine immobilization system. It is designed to help
prevent the engine from being started unless a coded key programmed
to your vehicle is used. Using the wrong key may prevent the engine
from starting. A message may appear in the information display.

If you are unable to start the engine with a correctly coded key, a
malfunction has happened and a message may appear in the information
display.

Automatic Arming

Your vehicle arms immediately after you switch the ignition off.

Automatic Disarming

Your vehicle disarms when you switch the ignition on with a coded key.

Replacement Keys

Note: Your vehicle comes equipped with two intelligent access keys.
The intelligent access key functions as a programmed key that operates

the driver door lock and activates the intelligent access with push button
start systems, as well as a remote control.

If your intelligent access key is lost or stolen and you do not have
an extra coded key, you will need to have your vehicle towed to an
authorized dealer. The key codes need to be erased from your vehicle
and new coded keys will need to be programmed.

Store an extra programmed key away from the vehicle in a safe place to
help prevent any inconveniences. See your authorized dealer to purchase
additional spare or replacement keys.

Programming a Spare Intelligent Access Key

Note: A maximum of four intelligent access keys can be programmed
to your vehicle. You must take your vehicle and all access keys to your

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

80 Security

authorized dealer to be erased and reprogrammed if you would like to
replace a previously programmed access key with a new access key,
or if you already have four access keys programmed to your vehicle.

You must have two previously programmed intelligent access keys
inside the vehicle and the new unprogrammed intelligent access keys
readily accessible. See your authorized dealer to have the spare key
programmed if two previously programmed keys are not available.

Make sure that the vehicle is off before beginning this procedure. Make
sure that all doors are closed before beginning and that they remain
closed throughout the procedure. Perform all steps within 30 seconds
of starting the sequence. Stop and wait for at least one minute before
starting again if any steps are performed out of sequence.

Read and understand the entire procedure before you begin.

1. Place the new unprogrammed
intelligent access key, with the
buttons facing down, in the pocket
inside of the center console.

2. Press the driver or passenger
power door unlock control three
times.

3. Press and release the brake pedal
one time.

4. Press the driver or passenger
power door lock control three times.

5. Press and release the brake pedal one time. The indicator on the
START/STOP button should begin to rapidly flash, indicating the
programming mode has been entered and two programmed intelligent
access keys have been detected in the vehicle.

6. Press the START/STOP button within one minute. A message will
appear in the information display indicating that the new intelligent
access key was programmed.

7. Remove the intelligent access key from the center console pocket and
press the unlock button on the newly programmed intelligent access key
to exit programming mode.

8. Verify that the remote entry functions operate (press lock then
unlock, making sure you end in unlock) and that the vehicle starts with
new intelligent access key.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Security 81

ANTI-THEFT ALARM

The system will warn you of unauthorized entry to your vehicle.
The turn signal lamps will flash and sound the horn up to a total of 10

times when:

• any door, the hood or the luggage compartment is opened without
using the keypad, the remote control or the intelligent access
transmitter

• the ignition is turned on with an invalid key.

Take all keys and remote controls to your authorized dealer if there is
any potential alarm problem with your vehicle.

Arming the Alarm

The system is ready to arm whenever the ignition is off. Lock the vehicle
to arm the alarm.

The turn signal lamps will flash once after locking the vehicle to indicate
the alarm is in the pre-armed mode and will become fully armed in
20 seconds.

Once fully armed, any intelligent access keys found inside the vehicle
may be disabled and will not start the engine. Press the remote control
unlock button to re-enable them.

Disarming the Alarm

To disarm the alarm, do any of the following:

• Press the power door unlock button within the 20-second pre-armed
mode will.

• Press the unlock button on the remote control.

• Unlock the doors with the keyless entry pad.

• Enter the vehicle using intelligent access.

• Press the panic button on the remote control. The alarm system will

still be armed, but this shuts off the horn and turn lamps when the
alarm is sounding.

Note: If the driver’s door is unlocked with a key, a chime will sound
when you open the door and a message will appear in the information
display. You will have 12 seconds to disarm the alarm using any of the
actions above, otherwise the alarm will trigger.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

82 Steering Wheel

ADJUSTING THE STEERING WHEEL

WARNING: Do not adjust the steering wheel when your vehicle
is moving.

Note: Make sure that you are sitting in the correct position. See Sitting
in the Correct Position in the Seats chapter.

1. Unlock the steering column.

2. Adjust the steering wheel to the
desired position.

3. Lock the steering column.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Steering Wheel 83

Power Tilt and Telescope Steering Column (If Equipped)

WARNING: Do not adjust the steering wheel when your vehicle
is moving.

Note: Make sure that you are sitting in the correct position. Refer to
Sitting in the Correct Position in the Seats chapter.

Use the control on the side of the
steering column to adjust the
position.

To adjust:

• tilt: use the top or bottom of the control

• telescope: use the front or rear of the control.

Easy Entry and Exit Feature

When you switch the ignition off, the steering column will move to
the full up and in position to allow extra room to exit your vehicle. The
column will return to the previous setting when you switch the ignition
on. You can enable or disable this feature in the information display.

Memory Feature

The steering column position saves when you do a memory set function.
You can recall it with the memory feature. Refer to the Seats chapter.

Pressing the adjustment control during memory recall will cancel the
operation. The column will respond to the adjustment control.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

84 Steering Wheel

AUDIO CONTROL

SEEK: Press to select the next or

IA

D

E

M

L

O

SEEK

T

U

M

V

E

VOL (Volume): Press to increase or decrease the volume.

VOICE CONTROL (IF EQUIPPED)

A

previous stored preset or track.
Press and hold to select the next or
previous frequency or seek through
a track.

MEDIA: Press repeatedly to scroll
through available audio modes.

MUTE: Press to silence the radio.

A. Phone mode
B. Voice recognition

K

E

E

S

VOL

B

See the MyLincoln Touch chapter.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Steering Wheel 85

CRUISE CONTROL

Type 1

Type 2

RES

SET

See the Cruise Control chapter for information on this feature.

CNCL

ON

OFF

GAP

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

86 Steering Wheel

INFORMATION DISPLAY CONTROL

Refer to the Information Displays
chapter for more information.

Cluster Display Control Features

Use this control to adjust the right
side of the cluster display. Navigate
through the screen and press OK
to select. Refer to the MyLincoln
Touch™ chapter.

HEATED STEERING WHEEL (IF EQUIPPED)

See the MyLincoln Touch chapter.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Wipers and Washers 87

WINDSHIELD WIPERS

Note: Fully defrost the windshield in icy conditions before turning on
the windshield wipers.

Note: Make sure the windshield wipers are switched off before entering
a car wash.

Note: Clean the windshield and wiper blades if they begin to leave
streaks or smears. If that does not resolve the issue, install new wiper
blades.

Note: Do not operate the wipers on a dry windshield. This may scratch
the glass, damage the wiper blades or cause the wiper motor to burn out.
Always use the windshield washers before wiping a dry windshield.

Rotate the end of the control away
from you to increase the speed of

2

1

0

Speed Dependent Wipers (If Equipped)

When your vehicle speed increases, the interval between wipes will
decrease when intermittent wipe is selected.

the wipers. Rotate toward you to
decrease the speed of the wipers.

Press the stalk down and release for
a single swipe of the wipers.

RAIN-SENSING WIPERS (IF EQUIPPED)

Note: Wet road conditions may result in inconsistent or unexpected
wiping or smearing. Lower the sensitivity, switch to normal or high-speed
wiping or turn the wipers off to reduce smearing.

Note: Turn off the wipers before entering a car wash.

Use the rotary control to adjust the
sensitivity to one of the interval

A
U
T

O

moisture settings. The wipers will not
cycle until moisture is detected on
the windshield. The wiper speed will
vary based on the amount of moisture
detected on the windshield and the
sensitivity setting. The wipers will

continue to wipe as long as moisture is detected.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

88 Wipers and Washers

This feature can be turned on or off using the information display.
Keep the outside of the windshield clean, especially the area around the

interior mirror where the sensor is located, or sensor performance may
be affected.

WINDSHIELD WASHERS

Note: Do not operate the wipers on a dry windshield. This may scratch
the glass, damage the wiper blades or cause the wiper motor to burn out.
Always use the windshield washer before wiping a dry windshield.

Note: Do not operate the washer when the washer reservoir is empty.
This may cause the washer pump to overheat.

Press the end of the stalk to
activate the washer.

2
1

0

• A brief press causes the wipers to swipe three times with washer fluid.

• A long press and hold will activate the wipers and washer fluid for up

to 10 seconds.

A wipe will occur a few seconds after washing to clear any remaining washer
fluid. This feature can be turned on and off in the information display.

REAR-WINDOW WIPER AND WASHERS

Rotate the control to select:
2 — Intermittent operation

2
1

0

(shortest pause between wipes).
1 — Intermittent operation (longest

pause between wipes).
0 — Off.

Rotate and hold the control to either the top or bottom position to
activate the rear washer. The control will return to the 2 or 0 position
when you release it.

When you select reverse gear, the rear wiper will switch on to
intermittent if the front wipers are activated. This feature may be
enabled or disabled in the information display.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

LIGHTING CONTROL

High Beams

Headlamp Flasher

Lighting 89

A. Off
B. Parking lamps, instrument panel

lamps, license plate lamps and tail
lamps

C. Headlamps

Push the lever forward to switch the
high beams on.

Push the lever forward again or pull
the lever toward you to switch the
high beams off.

•Pull toward you slightly to activate
and release to deactivate.

AUTOLAMPS

WARNING: In severe weather conditions, it may be necessary to
switch your headlamps on manually.

Note: If the vehicle is equipped with autolamps, it will have the
windshield wiper rainlamp feature. When the windshield wipers are
turned to low- or high-speed wiping during daylight, and the headlamp
control is in the autolamp position, the exterior lamps will turn on after
a brief delay and will remain on until the wipers are turned off.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

90 Lighting

The autolamp system provides light
sensitive automatic on-off control
of the exterior lights normally
controlled by the headlamp control.

The headlamps will remain on for a
period of time after you switch the
ignition off. You can adjust the time
delay using the message center
in the instrument cluster. See

Information displays.

INSTRUMENT LIGHTING DIMMER

Press repeatedly or press and hold
until the desired level is reached.

In the uplevel message center

Note:

only, a message will pop up that will
show incrementally where the
dimmer is in relation to the dimming
steps. These steps will also vary for
daytime and night time dimming.

Note: If the battery is disconnected, discharged, or a new battery is
installed, the dimmer will set the illuminated components to the
maximum setting automatically.

HEADLAMP EXIT DELAY

You can set the delay time to keep the headlamps on for up to three
minutes after the ignition is turned off.

Follow the steps below to change the delay time (Steps 1 through 6
must be done within 10 seconds):

1. Turn the ignition off.

2. Turn the lighting control to the autolamp position.

3. Turn the lighting control to the off position.

4. Turn the ignition on.

5. Turn the ignition off.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Lighting 91

6. Turn the lighting control to the autolamp position. The headlamps and
parking lamps will turn on.

7. Turn the lighting control to the off position when the desired delay
time has been reached. The headlamps and parking lamps will turn off.
You can set the headlamp exit delay to one of the following settings:

• Off

• 10 seconds

• 20 seconds

• 30 seconds

• 60 seconds

• 90 seconds

• 120 seconds

• 180 seconds.

Note: You can also adjust the time delay using the display controls in
the instrument cluster. See the Information Displays chapter.

DAYTIME RUNNING LAMPS (IF EQUIPPED)

WARNING: Always remember to turn on your headlamps at

dusk or during inclement weather. The Daytime Running Lamp
(DRL) system does not activate the tail lamps and generally may not
provide adequate lighting during these conditions. Failure to activate
your headlamps under these conditions may result in a collision.

The system switches the headlamps on with a reduced output (vehicles
equipped with halogen headlamps) or turns the front fog lamps on
(vehicles equipped with HID headlamps) in low light situations.

To switch the system on:

1. Switch the ignition on.

2. Switch the lighting control to the off, autolamp or parking lamp
position.

3. Make sure the transmission selector lever is not in position P.

4. Make sure the parking brake is disengaged.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

92 Lighting

FRONT FOG LAMPS

The fog lamps can be turned on when the
lighting control is in the headlamps, parking
lamps or autolamps positions and the high
beams are not turned on.

ADAPTIVE HEADLAMPS (if equipped)

The headlamp beams move in the same direction as the steering wheel
which provides more visibility when driving around curves.

A. Without adaptive headlamps

B. With adaptive headlamps

A

B

Note: The system has a power-up movement check feature. When the
vehicle is started, the lamps track left to right, then back to center to
alert the driver that the system is working properly. There is a delay of
two to five seconds before the adaptive headlamp system will operate
when the vehicle is driven, as the system is inactive below 3 mph
(5 km/h).

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Lighting 93

DIRECTION INDICATORS

The turn signal lever does not mechanically lock in the upward or
downward position when activated. The turn signal control activation and
cancellation is electronic.

• Push down to activate the left turn
signal.

• Push up to activate the right turn
signal.

• Push the lever again in either direction to manually cancel turn signal
operation.

Note: Tap the lever up or down to make the direction indicators flash
only three times to indicate a lane change.

INTERIOR LAMPS

Dome lamp control

Use to manually turn the dome lamp on.

• Press the control. This will turn on the
interior courtesy lights. The lights will
remain on until the control is pressed
again.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

94 Lighting

Front Row Map Lamps (If Equipped)

To turn on the map lamps, press the outer edge of the clear lens. The
front row map lamp lights when:

• any door is opened.

• the dome lamp button on the

instrument panel is activated.

• the remote entry controls are
pressed and the ignition is off.

Map/dome lamp (if equipped)

The dome lamp lights when:

• any door is opened.

• the dome lamp button on the

instrument panel is activated.

• any of the remote entry controls
are pressed and the ignition is off.

The map lamps are activated by pressing the controls on either side of
the lens.

Rear courtesy lamp

Located in the rear cargo area, the courtesy
lamp lights when:

• any door is opened.

• any of the remote entry controls are

pressed and the ignition is off.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Windows and Mirrors 95

POWER WINDOWS

WARNING: Do not leave children unattended in your vehicle
and do not let children play with the power windows. They may

seriously injure themselves.

WARNING: When closing the power windows, you should verify
they are free of obstructions and make sure that children and

pets are not in the proximity of the window openings.

Press or lift the switches to operate
the windows.

AUTO

Rear Window Buffeting

You may hear a wind throb or buffeting noise when one or both of the
rear windows are open. This noise can be reduced by lowering a front
window approximately 2–3 inches (5–8 centimeters).

One-Touch Up or Down (Front Windows)

This feature automatically opens or closes the window.
Press or lift the switch completely and release. The window will fully

open or close. Press or lift it again to stop the window.

AUTO

• Press the switch to the first
detent and hold to open the
window.

• Lift the switch to the first detent
and hold to close the window.

Global Opening

Note: The ignition must be off and the accessory delay feature must not
be activated to operate this feature.

Press and hold the unlock button on the remote control to begin opening
the front windows and venting the moonroof (if equipped). Release the
button once motion starts. The windows and moonroof will continue
opening.

Press the lock or unlock button on the remote control to stop motion.

Bounce-Back

The window will stop automatically while closing and reverse some
distance if there is an obstacle in the way.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

96 Windows and Mirrors

Overriding the Bounce-Back Feature

WARNING: When you override the bounce-back feature the
window will not reverse if it detects an obstacle. Take care when

closing the windows to avoid personal injury.

Pull up the window switch and hold within two seconds of the window
reaching the bounce-back position. The window will travel up with no
bounce-back protection. The window will stop if you release the switch
before the window is fully closed.

Accessory Delay

You can use the window switches for several minutes after you switch
the ignition off, or until you open either front door.

Window Lock

A. Unlock
B. Lock

A

Press the control to lock or unlock the rear window controls.

EXTERIOR MIRRORS

Power Exterior Mirrors

WARNING: Do not adjust the mirror while your vehicle is in
motion.

A

B

B

C

A. Left mirror
B. Off
C. Right mirror

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Windows and Mirrors 97

To adjust your mirrors:

1. Select the mirror you want to adjust.

2. Move the control in the direction you want to tilt the mirror.

3. Return the control to the center position to lock mirrors in place.

Fold-Away Exterior Mirrors

Push the mirror toward the door window glass. Make sure that you fully
engage the mirror in its support when returning it to its original position.

Memory Mirrors

You can save and recall the mirror positions through the memory
function. See Memory function in the Seats chapter.

Auto-Dimming Feature

The driver’s side exterior mirror will automatically dim when the interior
auto-dimming mirror is activated.

Signal Indicator Mirrors (If Equipped)

The outer portion of the appropriate mirror housing blinks when you
activate the turn signal.

Integrated Blind Spot Mirrors (If Equipped)

WARNING: Objects in the blind spot mirror are closer than they
appear.

Blind spot mirrors have an integrated convex mirror built into the upper
outboard corner of the exterior mirrors. They are designed to assist you
by increasing visibility along the side of your vehicle.

Check the main mirror first before a lane change, then check the blind
spot mirror. If no vehicles are present in the blind spot mirror and the
traffic in the adjacent lane is at a safe distance, signal that you are going
to change lanes. Glance over your shoulder to verify traffic is clear, and
carefully change lanes.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

98 Windows and Mirrors

The image of the approaching vehicle
is small and near the inboard edge
of the main mirror when it is at a
distance. The image becomes larger
and begins to move outboard across
the main mirror as the vehicle

C

B

A

Blind Spot Information System (BLIS®) with Cross Traffic
Alert (CTA) (If Equipped)

Refer to Blind Spot Information System (BLIS®) with Cross Traffic
Alert (CTA) in the Driving Aids chapter.

approaches (A). The image will
transition from the main mirror and
begin to appear in the blind spot
mirror as the vehicle approaches (B).
The vehicle will transition to your
peripheral field of view as it leaves
the blind spot mirror (C).

INTERIOR MIRROR

WARNING: Do not adjust the mirror when your vehicle is
moving.

Note: Do not clean the housing or glass of any mirror with harsh
abrasives, fuel or other petroleum or ammonia based cleaning products.

You can adjust the interior mirror to your preference. Some mirrors also
have a second pivot point. This lets you move the mirror head up or
down and from side to side.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)

Windows and Mirrors 99

Auto-Dimming Mirror

Note: Do not block the sensors on the front and back of the mirror.
Mirror performance may be affected. A rear center passenger or raised
rear center head restraint may also block light from reaching the sensor.

The mirror will dim automatically to reduce glare when bright lights are
detected from behind your vehicle. It will automatically return to normal
reflection when you select reverse gear to make sure you have a clear
view when backing up.

SUN VISORS

Slide-On-Rod

Rotate the visor toward the side
window and extend it rearward for
extra sunlight coverage.

Retract the visor before moving it
back toward the windshield and
storing it.

Illuminated Visor Vanity Mirror

Lift the cover to switch on the
lamp.

2013 MKX (mkx)
Owners Guide gf, 3rd Printing
USA (fus)