Aluminum Drive Roll Kits
KP1507 Series
INSTALLATION INSTRUCTIONS
Table of Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
General Description . . . . . . . . . . . . . . . . . . . . . .1
Contents of Kit . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Conduit & Bushing . . . . . . . . . . . . . . . . . . . . . .3
Drive Roll & Wire Guide . . . . . . . . . . . . . . . . . .4
Pressure Door Spring . . . . . . . . . . . . . . . . . . .5
Operation & Feeding Recommendations . . . . . .7
Fast Mate Guide Tubes . . . . . . . . . . . . . . . . . .7
Guns, Liners and Tips . . . . . . . . . . . . . . . . . . .8
IM614
October, 1997
SAFETY
Follow all safety guidelines in your power source and feeder operators manuals and any additional guidelines
covered in this manual.
GENERAL DESCRIPTION
The KP1507 series of drive roll kits contain a number of components, in addition to the drive rolls, to optimize the
wire feeder for aluminum feeding. These components are specifically designed to protect the aluminum wire
from abrasion and deformation, thereby avoiding many common aluminum feeding problems.
The provided plastic wire conduit and conduit bushing protect the wire from abrasion on it’s way into the wire
guides. The low friction plastic split wire guides protect the wire from abrasion, and support the wire as close as
possible to the drive rolls. The drive rolls have a special groove shape and finish. In addition, lower pressure
springs are provided for installation in the pressure door (except for kit KP1507-3/32A (2.4mm)). These springs
are optimized for aluminum feeding.
World's Leader in Welding and Cutting Products Premier Manufacturer of Industrial Motors
Sales and Service through Subsidiaries and Distributors Worldwide
22801 St. Clair Ave. Cleveland, Ohio 44117-1199 U.S.A. Tel. (216) 481-8100
KIT SIZES & CONTENTS
The table and figure below lists and illustrates the various K1507 series aluminum drive roll kits for the various
wire sizes. Also listed are the components included in each kit.
Drive Roll Kit KP1507-035A KP1507-040A KP1507-3/64A KP1507-1/16A KP1507-3/32A
Metric Wire Size 0,9 mm 1,0 mm 1,2 mm 1,6 mm 2,4 mm
English Wire Size .035 in .040 in 3/64 in (.047) 1/16 in (.063) 3/32 in (.094)
Included Items
1 Drive Rolls S22944-035A* S22944-040A* S22944-3/64A* S22944-1/16A* S22944-3/32A*
(Qty 4))
2 Inner Wire M18796-1 M18796-1 M18796-2 M18796-3 M18796-4
Guide
3 Outer Wire S22737-1 S22737-1 S22737-1 S22737-1 S22737-1
Guide
4 Conduit S23750-1 S23750-1 S23750-1 S23750-1 S23750-2
Bushing
5 Pressure T11862-57 T11862-57 T11862-57 T11862-57 Use Original
Spring
6 Knurled Knob S22933 S22933 S22933 S22933 S22933
Assembly
7 Flex Tube T10642-226 T10642-226 T10642-226 T10642-226 T10642-226
(Magnum Conduit)
8 Trust Washer T14043 T14043 T14043 T14043 T14043
(Qty 2)
9 1/8 Socket (T11563-2) (T11563-2) (T11563-2) (T11563-2) (T11563-2)
Key
10 5/32 Socket (T11563-5) (T11563-5) (T11563-5) (T11563-5) (T11563-5)
Key
11 7/64 Socket (T11563-6) (T11563-6) (T11563-6) (T11563-6) (T11563-6)
Key
*Drive rolls are packaged in quantities of 2 when ordered as a replacement part.
Item 1 Item 2 Item 3
Drive Rolls (Qty 4) Inner Wire Guide Outer Wire Guide
Item 4
Conduit Bushing
Item 5 Item 6
Pressure Springs (Qty 2) Knurled Knob Assembly
Item 7 Item 8
Conduit
Thrust Washers (Qty 2)
Figure 1 - Aluminum Drive Roll Kit Components
Items 9,10 & 11
Hex Keys
KP1507 SERIES ALUMINUM DRIVE ROLL KIT
2
INSTALLATION INSTRUCTIONS
Feed Head
Knurled Knob
Item 6
Conduit Bushing
Item 4
Set screw
location
Conduit
Item 7
WARNING
ELECTRIC SHOCK Can Kill
1. CONDUIT AND BUSHING
INSTALLATION
Refer to figure 2 and follow the following steps:
1. Turn off the welding power source.
• Only qualified persons should perform
this installation.
• Turn off the welding power source before installing
or changing drive rolls or guides.
• When inching with the gun trigger, the electrode and
drive mechanism are electrically “hot”.
------------------------------------------------------------------------
The installation instructions are divided into three sections:
1. Conduit bushing and conduit installation
2. Drive roll and wire guide installation
3. Pressure door spring installation (all kits except
KP1507-3/32A).
Note: Installation of the included pressure door
springs is not required, but is recommended for optimum wire feeding performance.
Figure 2 - Conduit Bushing and Conduit Installation
2.Loosen the set screw which secures the existing
incoming guide bushing and remove the bushing.
3. Thread the thumb screw into the new bushing.
Install the new conduit bushing into the wire feed
head.
Recommended Conduit Length:
Power Feed 10 13.0 in. (330 mm) as provided
LN-10, STT-10 11.5 in. (290 mm)
DH-10 10.0 in (250 mm)
Power Feed 11 1.0 in (25 mm)
4. FOR LINCOLN CONDUIT: Measure the conduit
and cut to the desired length. A tubing cutter makes
the best cut. A hacksaw or utility knife may also be
used.
5. Back out the thumb screw from the bushing insert
the conduit. Tighten the thumb screw. The thumb
screw threads will lock the conduit in place.
KP1507 SERIES ALUMINUM DRIVE ROLL KIT
3
2. DRIVE ROLL AND WIRE GUIDE
DRIVE
ROLL
SHAFTS
GUN ADAPTER
OPEN
LOCATING PIN
DRIVE
ROLLS
LOCATING PIN
PRESSURE
DOOR
(OPEN POSITION)
OPEN
INNER
GUIDE
KNURLED
KNOB
OUTER
WIRE GUIDE
INSTALLATION
Refer to figure 3 and follow the following steps:
1. Turn off the welding power source.
wire guide has arrows on it and must be installed
with the arrows pointing in the direction of wire travel.
2. Pull open the pressure door to expose the drive
rolls and wire guides.
3. Unscrew the knurled knob thumb screws counter
clockwise from the feed plate. Remove the outer
wire guide
4. Remove any existing drive rolls by pulling them
straight off the shaft. Wiggling the rolls makes
removal easier
5. Remove the Inner guide.
6. Orient the new inner wire guide that is supplied with
the kit groove side out. Install on feed plate by
locating over the two locating pins. Note: The inner
Figure 3 - Drive Roll Installation
7. Install each drive roll by pushing it over the shaft
until it seats against the locating shoulder on the
drive roll shaft.
8. Install the plastic outer wire guide, that is supplied
with the kit, by sliding it over the locating pins and
tightening the thumbscrews clockwise.
9. Engage the upper drive rolls if they are in the
“open” position and close the pressure door.
KP1507 SERIES ALUMINUM DRIVE ROLL KIT
4
3. PRESSURE DOOR SPRING
Wire Feeding
Direction
5
4
3
9
1
10
11
8
12
6
2
7
13
INSTALLATION
Note: This does not apply to the KP1507-3/32A kit,
which retains the original springs in the door.
1.Turn OFF Welding Power Source.
Disassembly:
2.Pull Open Item 1 (Pressure Door).
TOOLS REQUIRED: (supplied with kit)
• 7/64 HEX KEY WRENCH
• 5/32 HEX KEY WRENCH
HARDWARE REQUIRED: (supplied with kit)
• 2 STEEL THRUST WASHERS
• 2 SPRINGS
Refer to figure 4 and follow the following steps:
Procedure:
Figure 4 - Pressure Door Assembly
Item Description
1 Pressure door
2 Pressure arm
3 Cover plate
4 #10-24x.62 cap screw
5 Lock washer
6 Spring retaining rod
7 Spring
8 #6-32x1.00 cap screw
9 Indicator
10 Plastic thrust washer
11 Steel thrust washer
12 Adjustment knob
13 Steel thrust washer
3.Using the 5/32 Hex Key Wrench remove Item 4
(#10-24 Socket Head Cap Screw), and Remove
Item 3 (Cover Plate).
4.Turn Item 12 (Adjustment Knob) counter clockwise
until Item 7 (Springs) are fully relaxed.
5.Using the 7/64 Hex Key Wrench remove both Item 8
(#6-32X1.00 Socket Head Cap Screws).
Note:
This view shown is for a right side pressure
door assembly found on single head feeders.
Dual head feeders will have a left and right
side assembly. The parts used on the left and
right assemblies are identical. It is the way
they are assembled that makes them a Left
side or a Right side. Right and left heads are
designated by looking at the feeder from the
front (gun end).
KP1507 SERIES ALUMINUM DRIVE ROLL KIT
5
6 Remove Item 6 (Spring Retaining Rod) by grasp-
10
11
12
6
2
8
13
7
9
10
11
12
6
2
8
13
7
9
ing Item 12 (Adjustment Knob) and sliding it out of
Item 1 (Pressure Door). Item 10 (Plastic Thrust
Washers) and Item 11 (Steel Thrust Washer) will
also be removed along with Item 6 (Spring
Retaining Rod).
11. Repeat Step 9 and then go to step 12.
12. Continue to slide Item 6 (Spring Retaining Rod)
into Item 1 (Pressure Door) until Item 12
(Adjustment Knob) is seated against Item 1
(Pressure Door).
7. Remove Item 7 (Springs) from Item 1 (Pressure
Door)
Note: Be sure to save these springs for converting
the Wire Feeder back to feeding solid steel or
cored steel wire. Use these instructions for the
conversion.
Reassembly with new springs:
8. Slide Item 6 (Spring Retaining Rod) into Item 1
(Pressure Door) until it is just past the first Item 2
(Pressure Arm)
Note: Item 12 (Adjustment Knob), Item 10 (Plastic
Thrust Washers), and Item 11 (Steel Thrust
Washer) should still be on Item 6 (Retaining Rod)
9. Place 1 Item 13 (Steel Thrust Washer supplied
with kit) and 1 Item 7 (Spring supplied with Kit)
over Item 6 (Spring Retaining Rod).
Note: Be sure that the springs being installed are
for the proper type of wire to be fed. (Light springs
for aluminum, heavy springs for steel)
13. Slide Item 7 (Springs) and Item 13 (Steel Thrust
Washers) until they are against each of Item 2
(Pressure Arm).
14. The threaded hole in item 6 (Spring Retaining
Rod) nearest item 12 (Adjusting Knob) should be
lined up with the hole in item 9 (Indicator). Thread
item 8 (#6-32X1.00 Socket Head Cap Screw) into
and thru item 6 (Spring Retaining Rod) and then
approximately 2 turns into item 9 Indicator.
Note: If the threaded hole and indicator are NOT
lined up turn item 12 (Adjustment Knob) as
required clockwise or counter clockwise to adjust
the position of the threaded hole in item 6 (Spring
Retaining Rod) until it lines up with the indicator or
gently slide the indicator using the end of the 7/64
Hex Key Wrench until it is lined up.
15. Thread the other item 8 (#6-32X1.00 Socket Head
Cap Screw) into and thru the other threaded hole
in item 6 (Spring Retaining Rod) until it bottoms
on item 1 (Pressure Door) and then back off
approximately 1 turn.
10 Continue to slide Item 6 (Spring Retaining Rod)
into Item 1 (Pressure Door) until it is just past the
second Item 2 (Pressure Arm).
Figure 5 - Feed Head Component Orientation
Direction of wire feeding
Left Side Feed Head
Orientation
Dual Head Feeders Only
(Left as viewed from front of wire feeder)
KP1507 SERIES ALUMINUM DRIVE ROLL KIT
16 Before continuing, use the diagrams in figure 5 to
check the orientation and position of items
2,6,7,8,9,10,11,12, and 13.
Direction of wire feeding
Right Side Feed Head
Orientation
6
Dual & Single Head Feeders
17. Place Item 3 (Cover Plate) into Item 1 (Pressure
6
9
8
3
Door). Using the 7/64 Hex Key Wrench tighten
Item 8 (#6-32 1.00 Socket Head Cap Screw) until
the base of the screw head is even with the top
surface of Item 3 (Cover Plate) This is the screw
that was installed in Step 14 and is nearest to
Item 12 (Adjustment Knob). See figure 6 below for
reference.
ALUMINUM FEEDING RECOMMENDATIONS
• For optimum aluminum wire feeding, wire feeders
equipped with Lincoln Fast-Mate gun adapters
should be fitted with the appropriate S24129-* series
plastic lined Fast-Mate guide tube. These Fast-Mate
adapter guide tubes are designed specifically for
feeding aluminum (See part number listings in table
1):
Figure 6 - Cover Plate Installation (end view)
18. Using the 5/32 Hex Key Wrench secure Item 3
(Cover Plate) to Item 1 (Pressure Door) with Item
4 (#10-24X.625 Socket Head Cap Screw) and
Item 5 (Lock washer).
19. Turn Item 12 (Adjustment Knob) until the Item 8
(#6-32X1.00 Socket Head Cap Screws) begins
compressing Item 7 (Springs).
20. Close Item 1 (Pressure Door).
• Shorter guns will provide more robust wire feeding
performance. A 10ft (3.0 meter) gun is an excellent
choice. Longer guns should be reserved for the
harder alloys of aluminum.
• Lincoln offers dedicated models of Magnum water
cooled guns equipped specifically for aluminum
welding.(See
• The welding gun should be equipped with a plastic
liner that is designed for aluminum welding. Lincoln
sells liners designed for this purpose. (See
Liners and Tips
• The K1634-1 Wire reel cover kit can be installed to
keep the wire clean.
Guns, Liners and Tips
section):
section)
Guns,
FAST-MATE GUIDE TUBES
Table 1 below shows the various plastic lined guide
tubes that are recommended for use with Lincoln
Fast-Mate gun adapters when feeding aluminum.
The Installation of the Pressure Door Springs is now
complete.
OPERATION
Once installation of the kit is complete, the drive roll
pressure should be set to the lowest setting that provides adequate wire feeding force. When adjusted in
this manner, the drive rolls will not deform the wire.
Also, if a wire feed stoppage does occur at the gun,
the rolls will tend to slip on the wire rather than “bird
nest” the wire at the drive rolls.
Depending on the operating conditions, it may be necessary to clean the drive roll grooves periodically.
This operation removes any accumulated aluminum
from the grooves. Cleaning the roll grooves is performed with the rolls removed from the wire feeder,
and is best accomplished by using a commercially
available abrasive impregnated string or cord.
Table 1 S24129 Guide Tubes
Wire Size .030-.035 in .035-3/64 in 1/16 in
.8mm-.9mm .9mm-1.2mm 1.6mm
Tube Color Black Blue Red
FM Adapters
K489-2 S24129-4 S24129-5 S24129-6
K487-7 S24129-13 S24129-14 S24129-15
PowerFeed-11 S24129-1 S24129-2 S24129-3
KP1507 SERIES ALUMINUM DRIVE ROLL KIT
7
GUNS, LINERS and TIPS
The following are the various Magnum guns recommended for feeding aluminum when the appropriate
liners and contact tips are installed .
MAGNUM 450WC WATER COOLED GUN
MAGNUM 300, MAGNUM 300FM, MAGNUM 400,
MAGNUM 400FM, MAGNUM 400DSFM GUNS
Aluminum Liners for 10 ft (3.0 meter) guns:
M18732-1 (.030-.035 in, .8mm-.9mm) Black
M18732-5 (.035-3/64 in, .9mm-1.2mm) Blue
M18732-3 (1/16 in, 1.6mm) Red
Complete guns set up for aluminum feeding:
K684-7 10 ft (3.0 meter) length, .035-3/64 (.9mm -
1.2mm) wire
K684-8 10 ft (3.0 meter) length, 1/16in (1.6 mm)
wire
Aluminum Liners for 10 ft (3.0 meter) guns:
M18732-1 (.030-.035 in, .8mm-.9mm) Black
M18732-5 (.035-3/64 in, .9mm-1.2mm) Blue
M18732-3 (1/16 in, 1.6mm) Red
Aluminum Liners for 15 ft (4.5 meter) and shorter
guns:
M18732-2 (.030-.035 in, .8mm-.9mm) Black
M18732-6 (.035-3/64 in, .9mm-1.2mm) Blue
M18732-4 (1/16 in, 1.6mm) Red
Aluminum Contact Tips:
S22334-035A (.035 in, .9 mm)
S22334-040A (.040 in, 1.0 mm)
S22334-364A (3/64 in, 1.2 mm)
S22334-116A (1/16 in, 1.6 mm)
Note: M17714-1 and -2 liners can be used, but the
M18732 series is recommended.
Aluminum Liners for 15 ft (4.5 meter) and shorter
guns:
M18732-2 (.030-.035 in, .8mm-.9mm) Black
M18732-6 (.035-3/64 in, .9mm-1.2mm) Blue
M18732-4 (1/16 in, 1.6mm) Red
Note: M17714-1 and -2 liners can be used, but the
M18732 series is recommended.
Aluminum Contact Tips:
S18697-45 (.035 in, .9 mm) Notched
S18697-46 (3/64 in, 1.2 mm) Notched
S19391-9 (3/64 in, 1.2 mm)
S19392-7 (3/64 in, 1.2 mm) Heavy Duty
S19392-8 (1/16 in, 1.6 mm) Heavy Duty
MAGNUM 200 AND MAGNUM 200FM GUNS
Aluminum Liners:
M17714-1 (.035-3/64, .9mm-1.2mm)
Aluminum Contact Tips:
S18697-45 (.035 in, .9 mm) Notched
S18697-46 (3/64 in, 1.2 mm) Notched
S19391-9 (3/64 in, 1.2 mm)
S19392-7 (3/64 in, 1.2 mm) Heavy Duty
KP1507 SERIES ALUMINUM DRIVE ROLL KIT
8
Loading...