Lincoln 1130, 1132, 1133, D Series Operating And Installation Manual
PISTOL GRIP GREASE GUN
Models 1130
16 OZ. CAPACITY
14-1/2 OZ. CARTRIDGE
1132,1133
Series "D"
* OPTIONAL 91108 FILLER NIPPLE.
Must be ordered separately.
70458-5
©*70458-7
© 70458-9
© 70458-8
70458-3
70458-1
70458-4
93485
61620
55264
16665 45917
62939 13789
Model
1130
©Indicateschang
e
Model
1130
67020
**
5852
Model
1132
OPERATING INSTRUCTIONS
Model
1130
71518
**
5852
**RefertoServiceManua
l
SectionF4,Page2Series.
F
illthelubricantcontainer.Referto
instructions.
reversepagefor
Wipefittingscleanbeforelubricating.Pushcoupleronto
fittingataslightangleandthencentercoupleronthe
fitting.Squeezepistolgriptolubricate,takingcareno
t t
o
damagesealsbyexcessivepressureorlubricantvolume
.
Afterlubricating,turncouplerataslightangletoreleas
e
gripofthecouplerjaws.
Model
1133
SERVICE PARTS
PART DESCRIPTION
PART DESCRIPTION
5852
Hydrauli
c couple
r
70458-3Adapte
r
13789
Followerhandle
70458-4Gasket
16665
Follower rod
70458-5Head&handl
e
45917
Tubecap
70458-7Plug
55264
Followerspring
70458-8spring
61620
Containertube
70458-9Ba
ll
62939
Space
r
71518
Hos
e
67020
Pipenipple
93465
Followerassembl
y
70458-1
Headassembly
ADIVISIONOF
LINCOLN ST. LOUIS
McNEIL
SECTION -
D7
4010 GOODFELLOWBLVD •ST LOUIS,MO 63120 • (314) 679-4200
CORPORATION
PAGE
-46C
L-APR-84
Printed in United States of America
FORM 10304C
TO INSTALL A LUBRICANT CARTRIDGE
er handle. Exert force on the follower handle until lubricant
1) Remove head and plunger assembly from container tube.
oozes from the tube and head interface. Tighten container tube
into the head and plunger assembly.
2) To remove an empty cartridge, pull back on the follower handle
until the follower rod is fully extended. Then, carefully release
5) Disengage the follower rod from the follower by rotating the
the follower handle to eject the empty cartridge from the con-
follower handle. Push the follower rod into the container.
tainer tube. Pull back on the follower handle. When the follower
rod is fully extended, pull it sideways to latch the rod groove into
TO EXPEL AIR POCKETS
the keyhole slot in the container cap.
1) Unscrew the container tube l-1/2 turns from the head and
plunger assembly.
2) Withdraw the follower rod from the container cap and engage it
with the follower by rotating the follower handle. Exert force on
the follower handle until lubricant oozes from the tube and head
interface.
3) Tighten container tube into the head end-plunger assembly. Dis-
engage the follower rod from the follower by rotating the
follower handle. Push the follower rod into the container.
3) Remove the caps from both ends of the cartridge and insert the
large open end of the cartridge into the container tube.
IMPORTANT
4) Loosely assemble the head and plunger assembly to the contamer tube. Disengage the follower rod from the container cap.
Engage the follower rod with the follower by rotating the follow-
Air pockets in thecartridge lubricant will
cause the grease gun to lose itsprime.
TO CONVERT GREASE GUN TO ALLOW FILLING 5) Loosely assemble the head and plunger assembly to the filled
FROM BULK CONTAINER OR FILLER PUMP
container tube. Release the follower rod from the container cap
and disengage the follower rod from the follower by rotating the
1) Unscrew the container cap from the container tube. Pull on the
follower handle. Push the follower rod into the container. Slowly
follower handle to extract the follower and spring from the unscrew the container tube from the head and plunger assembly
container tube. until lubricant oozes from the interface. Tighten container tube
2) Grasp follower between thumb and forefinger and flip the
follower lip from the rear to the front side.
NOTE: The follower resembles a cup. When the grease gun is
assembled for use with bulk lubricant, the cup opens
toward the head assembly.
3) Reassemble follower into container tube and position with the
follower handle so that the container cap can be tightened onto
the container tube.
into the head and plunger assembly.
TO FILL GREASE GUN WITH A FILLER PUMP
Engage the follower rod with the
follower by rotating the follower
TO FILL GREASE GUN FROM
handle. Insert the grease gun
BULK LUBRICANT CONTAINER
filler nipple into the filler pump
socket. Operate the filler pump
1)Remove head and plunger assembly from container tube.
to fill the grease gun container.
When the follower rod groove is
2) Pack lubricant into cavity of the head and plunger assembly.
exposed, the container is fried
3) Insert the open end of the container tube into lubricant. Slowly
(follower rod will be extended
pull the follower handle back while pushing the container tube
approximately 8 inches). Dis-
deeper into the lubricant to prevent air pockets from being
engage the follower rod from the
pulled into the container tube.
follower by rotating the follower
handle. Push the follower rod
4) When the follower rod is fully extended, pull it sideways to latch
into the container.
the rod groove into the keyhole slot in the container cap.
RETAIN THIS INFORMATION FOR FUTURE REFERENCE
When ordering replacement parts, list: Part Number, Description, Model Number, and Series Letter.
LINCOLN ST. LOUIS provides a Distributor Network that stocks equipment and replacement parts.
A list of Authorized Service Departments will be furnished upon request.
Loading...