Lincat Seal FDB4, Seal FDB5, Seal FDB6, Seal FDB8, Seal FDB10 User And Installation Instructions Manual

IS277 ECN 3850

User and Installation Instructions

Seal Refrigerated Food Display and
Preparation Bars

FDB4, FDB5, FDB6, FDB8. FDB10, FPB5,
FPB7

IS277 ECN 3850

Page 2

Dear Customer,
Thank you for purchasing this Lincat product.

This is just one of over 450 different items of catering equipment available which is
constantly being extended and improved. Details are available from your local
distributor or direct from us.
Used for the purposes for which it is intended, and with careful maintenance as
outlined in this User Guide, your Lincat product will give years of trouble free use.

IMPORTANT INFORMATION

Please read all of the safety and operating instructions carefully
before using this product. Please pay particular attention to all
sections of this User Guide that carry warning symbols and notices.

WARNING!
This is a Warning symbol. This symbol is used throughout the
user guide whenever there is a risk of personal injury. Ensure
that these warnings are read and understood at all times.

CAUTION!

This is a Caution symbol. This symbol is used throughout the User
Guide whenever there is a risk damaging your Lincat product. Ensure
that these warnings are read and understood at all times.

NOTE:

This is a Note symbol. This symbol is used throughout the User Guide to
provide additional information, hints and tips.

NOTE

IS277 ECN 3850

Page 3

CONTENTS

Contents Page

Safety instructions………………………………………………………4
Product specification………………………………………………….. 5
Features………………………………………………………………….. 5
Technical specification…………………………………………………5
Pack contents…………………………………………………….………5
Spare parts list………………………………………………………….. 5
Installation……………………………………………………………….. 6
Connecting to the electricity supply……………………………. 6
Operating instructions………………………………………………….7
Defrosting…………………………………………………………. 7
Cleaning and maintenance……………………………………………. 7
Service information…………………………………………………….. 8
Conditions of guarantee…..…………………………………….…….. 8

USE OF THE FOOD DISPLAY BARS AND PREPARATION BARS

The Food Display Bars and Preparation Bars are intended to be used on
counter tops to display chilled food products placed in Gastronorm (GN)
containers.

IS277 ECN 3850

Page 4

SAFETY INSTRUCTIONS

WARNING!
Basic safety precautions, including the following, should be
followed to reduce the risk of personal injury. Make sure you

have read all of these instructions before switching on the unit.
Keep this User Guide in a safe place for future reference for you and your
staff.
Do not clean the unit with a water jet.

REMOVAL OF PACKAGING

In the interest of hygiene, you should clean the product after unpacking and
ensure all plastic coatings are removed before use.

This unit is heavy. Take care when moving it.

GENERAL

Do not try to modify this product.
Ensure that the electrical supply cable is not damaged.

If the supply cable is damaged, it should be replaced by Lincat Ltd or suitably
qualified persons, in order to avoid a hazard.

IS277 ECN 3850

Page 5

PRODUCT SPECIFICATION

PACK CONTENTS

FEATURES

SPARE PARTS LIST

TECHNICAL SPECIFICATION

Food Display Bar – FDB4, FDB5, FDB6, FDB8, FDB10
Food Preparation Bar – FPB5, FPB7

Stainless steel body
Static refrigeration

Electronic control
Manual defrost

230V, 50Hz, single phase

Model

FDB4

FDB5

FDB6

FDB8

FDB10

FPB5

FPB7

GN container
capacity (100mm
deep maximum)

1/3 GN

4 5 6

8

10 5

7

Max. Operating
Temperature

O

C

25

25

25

25 25 25

25

Power rating

Watt

170

170

170

170

170

170

170

Width

mm

1045

1222

1399

1753

2107

1225

1580

Depth

mm

375

375

375

375

375

375

375

Height

mm

245

245

245

245

245

262

262

Weight (net)

kg

22

24

25

29

32

25

29

Volume (gross)

litres

NA

NA

NA

NA

NA

NA

NA

Volume (net)

litres

NA

NA

NA

NA

NA

NA

NA

Refrigerant

R134a

Refrigerated Food Display Bar or Preparation Bar (with cable and 13 Amp
plug). Glass section or stainless steel lid (if ordered with unit)

User Guide and Guarantee Card

Model

Component

Part no.

ALL FDB & FPB

MODELS

Tangential fan

FA51

Condenser

G/CD01

Compressor

G/CR10

Removable filter

G/FI25

Digital stat

S/E0486

Switch

SW67

IS277 ECN 3850

Page 6

INSTALLATION

Ensure the unit is installed on a sound level surface and not in direct
sunlight, damp or extreme temperature conditions. If the ambient
(operating) air temperature exceeds the one shown in the Technical

Specification (P.5), damage to the refrigeration system could occur.
The feet must not be removed, as this will damage the supply cable and
eventually the internal components.

For safety regulations, the plug must always be accessible.

Leave the product to stand for three hours before connecting to the
power supply and switching on.

CONNECTING TO THE ELECTRICITY SUPPLY

Ensure that the voltage of your electricity supply corresponds to the
serial plate details. The product is supplied with a 13 Amp plug. To
replace the plug, follow these instructions:

 green and yellow wire to 'E' or (Earth)
 blue wire to 'N' (Neutral)
 brown wire to 'L' (Live)

THIS APPLIANCE MUST BE EARTHED.

NOTE

IS277 ECN 3850

Page 7

OPERATING INSTRUCTIONS

CLEANING AND MAINTENANCE

Connect the unit to the electricity
supply. Switch the unit on (green
switch), insert empty Gastronorm
containers (100mm deep maximum)
with lids and wait until the
temperature display shows -2O C. At
this point introduce your chilled food
product. It is good working practice
to periodically monitor the food
temperature and to use lids on GN containers. The unit is not designed for long­term storage.

The temperature display relates to the temperature measured in the

well of the unit, not the temperature of the food product.

DEFROSTING

The unit is not designed to defrost automatically. For best performance you
should carry out the following defrosting instructions daily. Switch the unit off,
disconnect from the electricity supply and remove the containers. After 30
minutes some water may form in the well. Dry with a cloth.

CLEANING

Disconnect the product from the electricity supply before starting to

clean. Use a mild detergent in hot water and a soft cloth. Do not use
abrasive creams or scourers. Use a suitable polish on the exterior metal
surfaces by spraying onto the cloth (not directly onto the steel).

MAINTENANCE

It is recommended that a qualified refrigeration service engineer
checks this unit annually. It should not be necessary to alter the
digital controller, as it has been factory set.

For best performance you should clean the filter weekly (see Picture 1).
Slide out; use a soft brush to remove particles and replace. Do not
place the filter in water.

NOTE NOTE

1

2

3

4

1. Temperature Display

2. On/Off Switch

3. Cable

4. Filter Position

1

IS277 ECN 3850

Page 8

SERVICE INFORMATION

GUARANTEE

For help regarding the installation, maintenance and use of your Lincat
equipment, please contact our Service Department:

 01522 875520

All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out
by other persons.

To ensure your call is service enquiry is handled as efficiently as possible, you
need to have the following details available:

Brief details of problem
Product code, type number and serial number of unit (both on serial plate)
Code number of spare part (see spare parts list), if known

Lincat reserve the right to carry out any work under warranty during normal
working hours, i.e. Monday to Friday, 8.30 a.m. – 5.00 p.m.

This unit carries a comprehensive UK twelve-month warranty. The
guarantee is in addition to, and does not diminish, your statutory or legal
rights.

The guarantee does not cover: -

 Accidental damage, misuse (or use not in accordance with the instructions in

this User Guide), or consumable items

 Damage due to incorrect installation, modification or unauthorised service

work

 The manufacturer disclaims any liability for incidental, or consequential

damages