Lincat Seal C6A/75B, Seal C6A/100S, Seal C6A/100B, Seal C6A/75S Installation, Operating And Servicing Instructions

Please make a note of your product details for
future use:

Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________

Installation, Operating and Servicing
Instructions

Seal Ambient Merchandisers
C6A/75B, C6A/75S, C6A/100B, C6A/100S

IS 283 ECN 3607 Page 1 of 6

CONTENTS

Important Information

2

Warnings and Precautions

3

Technical Data

3

Checklist of Enclosures

3

Installation and Commissioning

3-4

Operating Instructions

4

Cleaning

4

Servicing, Maintenance and Component Replacement

5

Fault Finding

5

Spare Parts List

5

Service Information and Guarantee

6

IMPORTANT INFORMATION

Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.

WARNING!

This symbol is used whenever there is a risk of personal injury.

CAUTION!

This symbol is used whenever there is a risk of damaging your Lincat product.

NOTE:

This symbol is used to provide additional information, hints and tips.

KEEP THIS MANUAL FOR FUTURE REFERENCE

IS 283 ECN 3607 Page 2 of 6

WARNINGS AND PRECAUTIONS

TECHNICAL DATA

C6A/75

C6A/100

Height (mm)

755

Width (mm)

750

1000

Depth (mm)

650

Weight (kg)

41.7

51.5

Volume (l)

284

380

Power rating (W)

18

CHECK LIST OF ENCLOSURES

Warranty card

Instructions manual

2 x shelves

3mm Allen key

INSTALLATION AND COMMISSIONING

This appliance must be Installed, Commissioned and Serviced by a qualified
person in accordance with national and local regulations in force in the country of
installation.

If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.

Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
Disconnect this appliance before servicing, maintenance or cleaning.

This appliance must be earthed.

An equipotential bonding terminal is provided to allow cross bonding with other
equipment.

IS 283 ECN 3607 Page 3 of 6

If replacing the plug connect the terminals as follows:

OPERATING INSTRUCTIONS

CLEANING

Green and Yellow wire Earth E
Blue wire Neutral N
Brown wire Live L

Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)

Install this appliance on a level surface.

Only qualified or trained personnel should use this appliance.
Ensure the base plates lay flat within the base, and the shelves are secure.

Connect the appliance to the electricity supply and switch on the light using the
green switch.

Adjusting the shelf positions

Disconnect from the electricity supply. Slide the doors to the middle and lift up and
out of the runners to remove. Lift and rotate the shelves to remove. Use the Allen

key provided to adjust the shelf supports – at the front remove the two screws and
replace in the appropriate holes, at the rear the screws are located behind the cable
panel. Carefully remove the cable panel first and then reposition the rear shelf
supports. Replace the cable panel ensuring the cable is not trapped.

Do not use a water jet or steam cleaner, and do not immerse this appliance.
Remove the rear doors, shelves and base plates. Brush the crumbs into the tray.

Shelves, shelf supports and base trays may be washed in a dishwasher, clean all
other panels with warm water and mild detergent, do not use abrasive materials.
Dry with a soft cloth.

IS 283 ECN 3607 Page 4 of 6

SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT

Part Number

Description

Used on

BU171

Light tube

All

BP28

Front base plate

75 models

BP29

Rear base plate

BP30

Front base plate

100 models

BP31

Rear base plate

GL68

Lamp starter

All

S/M0085

Self service door knob

S models

SH97

Shelf

75 models

SH98

Shelf

100 models

FAULT FINDING

SPARE PARTS LIST

Replacing a light bulb
Disconnect from the electricity supply and ensure the bulb is cool to touch.
Using the Allen key provided remove the end caps from the light unit. Remove the

diffuser from the clips. Remove the tube by carefully rotating 900 and slowly ease
down until it is released. Replace the starter at the same time – to remove the
starter rotate it clockwise. Reverse the sequence to fit the new tube.

All other servicing, maintenance and component replacement on this appliance
should be carried out by one of our recommended service engineers.

Please refer to the Service Help Desk number on the final page of this manual.

IS 283 ECN 3607 Page 5 of 6

 Product code

All available on serial plate

 Type number

 Serial number

SERVICE INFORMATION

For help with the installation, maintenance and use of your Lincat equipment,
please contact our service department:

 UK: 01522 875520

For non-UK customers, please contact your local Lincat dealer

All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.

To ensure your service enquiry is handled as efficiently as possible, please tell us:
 Brief details of the problem

Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.

GUARANTEE

This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is
in addition to, and does not diminish your statutory or legal rights.

The guarantee does not cover:

 Accidental damage, misuse or use not in accordance with the manufacturer’s

instructions

 Consumable items (such as filters, glass, bulbs, slot toaster elements and door

seals.)

 Damage due to incorrect installation, modification, unauthorised service work or

damage due to scale, food debris build-up, etc.

The manufacturer disclaims any liability for incidental, or consequential damages.

Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.

Service calls to equipment under warranty will be carried out in accordance with the
conditions of sale. Unless otherwise specified, a maximum of 15 minutes of
administrative time, not spent directly carrying out servicing work, is provided for
within the warranty. Any requirement for staff attending the call to spend greater time
than 15 minutes due to administrative requirements, such as on health and safety risk
assessments, will be chargeable at the prevailing rate.

IS 283 ECN 3607 Page 6 of 6