Page 1
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________
Installation, Operating and Servicing
Instructions
Lynx Deck Pizza Oven
LDPO
IS 730 ECN 4511 Page 1 of 8
Page 2
CONTENTS
Important Information
2
Warnings and Precautions
3
Technical Data
3
Checklist of Enclosures
3
Installation and Commissioning
4
Operating Instructions
5-6
Cleaning
7
Servicing, Maintenance and Component Replacement
7
Fault Finding
7
Spare Parts List
7
Accessories
7
Service Information and Guarantee
8
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE
IS 730 ECN 4511 Page 2 of 8
Page 3
WARNINGS AND PRECAUTIONS
TECHNICAL DATA
Height (mm)
300
Width (mm)
530
Depth (mm)
560
Weight (kg)
28
Power Rating (kW)
2.2
CHECK LIST OF ENCLOSURES
Instructions manual
Kiln Bat
This appliance must be installed, commissioned and serviced by a qualified person
in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
The thermostats within this unit contain Potassium-Sodium alloy that react with
water and can cause burns. Under no circumstances should the capillary/bulb be
cut open.
IS 730 ECN 4511 Page 3 of 8
Page 4
INSTALLATION AND COMMISSIONING
This appliance must be earthed.
An equipotential bonding terminal is provided to allow cross bonding with other
equipment.
If replacing the plug connect the terminals as follows:
Green and Yellow wire Earth E
Blue wire Neutral N
Brown wire Live L
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)
Install this appliance on a level surface ensuring all vents are unobstructed. Any
partitions, walls or furniture must be of non-combustible material. Minimum
distances A 100mm, B 100mm – see Fig 1. Allow 50mm at rear of unit for vent.
IS 730 ECN 4511 Page 4 of 8
Page 5
A
H
D
B
C
E
G
F
I
J
OPERATING INSTRUCTIONS
Fig 2 – (FRONT VIEW)
Fig 3 - REAR VIEW
A – DOOR HANDLE
B – 20 MINS MECHANICAL TIMER
C – GREEN NEON (POWER)
D – BASE CONTROL THERMOSTAT (1 – 6)
E – BASE THERMOSTAT AMBER NEON (HEATING)
F – OVEN CONTROL THERMOSTAT (Up to 400oC)
G – OVEN THERMOSTAT AMBER NEON (HEATING)
H – THERMOMETER (TEMPERATURE DIAL)
I – MAINS POWER INLET
J – OVEN VENT
IS 730 ECN 4511 Page 5 of 8
Page 6
Setting
Approximate Temperature (°C)
1
50
2
100
3
150
4
200
5
250
6
300
Only qualified or trained personnel should use this appliance.
With all the control knobs in the ‘off/ 12 o’clock’ position, plug the unit into a 13A wall
socket and switch on. The green neon (C) located on the fascia will then illuminate
indicating power to the appliance.
Set the oven element control knob (F) to the desired temperature. The amber neon
(G) will illuminate.
Note: Oven is thermostatically controlled, the amber neon will only illuminate when
temperature drops below desired temperature.
Turn the base element control knob (D) to desired setting. The amber neon (F) will
illuminate.
Temperatures on both thermostats are approximate, dial for indication only.
At high oven temperatures such as 370oC, the base element will only need to power
on when stone cools below 300oC (e.g. when food is heavily loaded)
Note: Base is thermostatically controlled. The amber neon will only illuminate when
base stone drops below temperatures listed below:
Allow approximately 20-30 minutes for unit to reach max temperature on pre heat.
The oven cavity temperature is indicated by the dial (H).
Timer (B) is a mechanical timer only. Set to desired time (Minutes), a short bell will
sound when time has lapsed.
To turn the appliance off, set control knobs (D) and (F) to the off 12 o’clock position
and switch outlet socket to off. The green neon will no longer be illuminated, indicating
no power to the unit.
IS 730 ECN 4511 Page 6 of 8
Page 7
CLEANING
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
Part Number
Description
LT01
Load Tool
FAULT FINDING
SPARE PARTS LIST
ACCESSORIES
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent, do not use abrasive materials.
Dry with a soft cloth.
Occasionally remove the kiln bats and sweep/ vacuum out any debris from the base of
the appliance. It is suggested a lever is used to aid in removing the stone from the slot
at front of the unit.
All servicing, maintenance and component replacement on this appliance should be
carried out by one of our recommended service engineers.
Please refer to the Service Help Desk number on the final page of this manual.
Please contact the spares department for all spares requirements.
IS 730 ECN 4511 Page 7 of 8
Page 8
Product code
All available on serial plate
Type number
Serial number
SERVICE INFORMATION
For help with the installation, maintenance and use of your Lincat equipment,
please contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.
To ensure your service enquiry is handled as efficiently as possible, please tell us:
Brief details of the problem
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is
in addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:
Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
Consumable items (such as filters, glass, bulbs, slot toaster elements and door
seals.)
Damage due to incorrect installation, modification, unauthorised service work or
damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.
Service calls to equipment under warranty will be carried out in accordance with the
conditions of sale. Unless otherwise specified, a maximum of 15 minutes of
administrative time, not spent directly carrying out servicing work, is provided for
within the warranty. Any requirement for staff attending the call to spend greater time
than 15 minutes due to administrative requirements, such as on health and safety risk
assessments, will be chargeable at the prevailing rate.
IS 730 ECN 4511 Page 8 of 8
Loading...