Page 1
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________
Installation, Operating and Servicing
Instructions
Lynx Electric Convection Ovens
LCOT, LCOS, LCOXL
IS 733 ECN 4552 Page 1 of 9
Page 2
CONTENTS
Important Information
2
Warnings and Precautions
3
Technical Data
3
Checklist of Enclosures
3
Installation and Commissioning
3
Operating Instructions
5
Cleaning
6
Servicing, Maintenance and Component Replacement
7
Fault Finding
7
Spare Parts List
7
Service Information and Guarantee
8
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE
IS 733 ECN 4552 Page 2 of 9
Page 3
WARNINGS AND PRECAUTIONS
TECHNICAL DATA
Model
Height (mm)
Width (mm)
Depth (mm)
Weight (kg)
LCOT
520
495
570
29.3
LCOS
520
405
570
28.4
LCOXL
605
670
570
49.6
CHECK LIST OF ENCLOSURES
Instruction manual
1
Wire shelves LCOT, LCOS
2
Wire shelves LCOXL
3
Feet LCOXL
4
INSTALLATION AND COMMISSIONING
This appliance must be installed, commissioned and serviced by a qualified person
in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
This appliance must be earthed.
An equipotential bonding terminal is provided to allow cross bonding with other
equipment.
If replacing the plug connect the terminals as follows:
Green and Yellow wire Earth E
IS 733 ECN 4552 Page 3 of 9
Page 4
Blue wire Neutral N
B
A
A
Brown wire Live L
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)
Install this appliance on a level surface ensuring all vents are unobstructed. Install
this appliance on a level surface ensuring all vents are unobstructed. Any partitions,
walls or furniture must be of non-combustible material. Minimum distances A
100mm B 1000mm – see Fig 1.
Fig 1
IS 733 ECN 4552 Page 4 of 9
Page 5
Power Ratings
Model
kW
Amps
LCOT, LCOS, LCOXL
2.5
10.9
OPERATING INSTRUCTIONS
RESET BUTTON
Only qualified or trained personnel should use this appliance.
Connect the appliance to an electricity supply and switch on at the socket. Press the
switch on the appliance to the ‘On’ position – the switch and interior light illuminate,
and the fan operates.
Turn the temperature control knob to the desired setting – the amber neon
illuminates and extinguishes when temperature is reached.
During operation, the amber neon will periodically illuminate as the element cycles.
Adjacent to the temperature control is a 55 minute mechanical timer.
This appliance is fitted with a safety thermostat, which will cut power to the appliance
under fault conditions. If the switch illuminates but the appliance does not heat up,
the safety thermostat may need re-setting. This is achieved by pressing the red
button located as shown in Fig 2. Note that in the event of the safety thermostat
operating, the appliance must be allowed to cool before it can be re-set.
Fig 2
IS 733 ECN 4552 Page 5 of 9
Page 6
CLEANING
1. Back off bolts 2mm
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent. Do not use abrasive
materials, and do not use caustic or chloride based cleaners. Dry with a soft cloth.
If required, the shelf supports in the oven may be removed to allow a thorough clean
of the interior. The shelves are bolted in place tightly during transport to avoid
damage. On delivery, back off the 3 bolts holding each shelf by 2mm. This will allow
the shelf supports to be pushed upward slightly and then lifted out through the
keyhole slot provided. On re-fitting, the bolts do not need to be retightened, which
will allow the shelf supports to be clipped in and clipped out as necessary in the
future.
IS 733 ECN 4552 Page 6 of 9
Fig 3
Page 7
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
Part Number
Description
BU55
Door hinge bush
EL232
Element
FA106/S
Fan
FE37
Foot LCOT, LCOS
FE10
LCOXL
GA75
Fan gasket
GL707
Door inner glass LCOT
GL709
Door inner glass LCOS
GL711
Door inner glass LCOXL
KN250
Control/Timer knob
LA14
Lamp
LE14
Clear cover for On/Off switch
NE42
Amber neon
PL202
Mains cable
SE35
Door seal top – LCOT or Door seal side LCOXL
SE94
Door seal side – LCOT, LCOS
SE95
Door seal top - LCOS
SE96
Door seal top - LCOXL
SH139
Shelf LCOT
SH140
SH141
Shelf LCOXL
SW69
Switch
TH46
Control thermostat
FAULT FINDING
SPARE PARTS LIST
Door inner glass: Slide glass up to clear side brackets and remove from top. To
replace the glass, reverse the procedure.
Light bulb: Lever off the glass cover using a small flat bladed screwdriver. Unscrew
bulb. To replace the bulb, reverse the procedure.
Door seals: These simply hook out of the holes. Hook out to remove and replace by
hooking the new seal into position.
All other servicing, maintenance and component replacement on this appliance
should be carried out by one of our recommended service engineers.
Please refer to the Service Help Desk number on the final page of this manual.
IS 733 ECN 4552 Page 7 of 9
Page 8
TH203
Safety thermostat
TI37
Timer
Product code
All available on serial plate
Type number
Serial number
SERVICE INFORMATION
For help with the installation, maintenance and use of your Lincat equipment, please
contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.
To ensure your service enquiry is handled as efficiently as possible, please tell us:
Brief details of the problem
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is in
addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:
Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
Consumable items (such as filters, glass, bulbs, slot toaster elements and door
seals.)
Damage due to incorrect installation, modification, unauthorised service work or
damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.
Service calls to equipment under warranty will be carried out in accordance with the
conditions of sale. Unless otherwise specified, a maximum of 15 minutes of
administrative time, not spent directly carrying out servicing work, is provided for within
the warranty. Any requirement for staff attending the call to spend greater time than 15
IS 733 ECN 4552 Page 8 of 9
Page 9
minutes due to administrative requirements, such as on health and safety risk
assessments, will be chargeable at the prevailing rate.
IS 733 ECN 4552 Page 9 of 9
Loading...