Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________
Installation, Operating and Servicing
Instructions
Seal Heated Display Bars
HB1, HB2, HB3, HB4, LD2, LD3, LD4
IS 280 ECN 3607 Page 1 of 9
CONTENTS
Important Information
2
Warnings and Precautions
3
Technical Data
3
Checklist of Enclosures
3
Installation and Commissioning
4-5
Operating Instructions
6
Cleaning
7
Servicing, Maintenance and Component Replacement
7
Fault Finding
7
Spare Parts List
8
Accessories
8
Service Information and Guarantee
9
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE
IS 280 ECN 3607 Page 2 of 9
WARNINGS AND PRECAUTIONS
TECHNICAL DATA
Model
Height (mm)
Width (mm)
Depth (mm)
Weight (kg)
HB1
115
381
531
7
HB2
115
754
531
11
HB3
115
1094
531
15
HB4
115
1434
531
19
LD2
562
790
538
18
LD3
562
1130
538
24
LD4
562
1470
538
30
CHECK LIST OF ENCLOSURES
Warranty card
Instructions manual
Glass sneeze screen (LD models)
Sneeze screen fixing kit (LD models)
This appliance must be Installed, Commissioned and Serviced by a qualified
person in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
IS 280 ECN 3607 Page 3 of 9
INSTALLATION AND COMMISSIONING
This appliance must be earthed.
An equipotential bonding terminal is provided to allow cross bonding with other
equipment.
If replacing the plug connect the terminals as follows:
Green and Yellow wire Earth E
Blue wire Neutral N
Brown wire Live L
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)
Install this appliance on a level surface ensuring all vents are unobstructed. Any
partitions, walls or furniture must be of non-combustible material. Minimum
distances A 100mm B 500mm – see Fig 1.
Fig 1
IS 280 ECN 3607 Page 4 of 9
Do not remove the feet otherwise the appliance will overheat.
Model
kW
Amps
HB1
0.5
2.2
HB2
1.0
4.3
HB3
1.4
6.1
HB4
1.75
7.6
LD2
1.5
6.5
LD3
2.4
10.4
LD4
2.75
12.0
Power Ratings
For LD models, attach the glass sneeze screen to the appliance. To avoid
damaging the glass, it is important to assemble the fixings in the order shown in
Fig 2. Use a second person to support the glass during assembly.
Place the glass behind the metal cover and align the holes.
Push the bolt (A) through from the outside. Push the nylon sleeve (B) over the bolt
from the inside. Place on the washer (C) and fit the locknut (D). Do not overtighten.
Fig 2
IS 280 ECN 3607 Page 5 of 9
OPERATING INSTRUCTIONS
Only qualified or trained personnel should use this appliance.
Consulting Fig 3(LD model shown), connect the appliance to the electrical supply
and switch on (B).
Turn the control knob (A) to the desired setting and wait 20 minutes for the
appliance to heat up.
Place the containers with hot food on the hob surface and switch on the infrared
lamps (C).
Fig 3
IS 280 ECN 3607 Page 6 of 9
CLEANING
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
FAULT FINDING
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent, do not use abrasive
materials. Dry with a soft cloth.
The infrared lamps on LD models are replaceable. Disconnect the appliance from
the supply and allow to cool.
The bulb holders are sprung loaded - carefully push old lamp against either end
terminal until the opposite end is free.
Remove lamp and reverse procedure to insert replacement. Handle the
replacement lamp by the ceramic end caps and avoid touching the glass.
All other servicing, maintenance and component replacement on this appliance
should be carried out by one of our recommended service engineers.
Please refer to the Service Help Desk number on the final page of this manual.
IS 280 ECN 3607 Page 7 of 9
Part Number
Description
Used on
EL134
Element
HB4, LD4
EL135
Element
HB3, LD3
EL136
Element
HB2, LD2
EL214
Element
HB1
FE10
Foot
All
GL492
Glass screen
LD2
GL493
Glass screen
LD3
GL494
Glass screen
LD4
KN203
Control knob
All
LA210
Infrared lamp
LD Models
LA211
Lamp holder
LD models
PL202
Plug and lead
All
SW69
On/Off switch
All
SW70
Light switch
LD models
TH69
Thermostat
All
Part Number
Description
Used on
HBBM2
Bain marie adaptor including GN dishes and lids
HB2
HBBM3
HB3
HBBM4
HB4
LDBM2
LD2
LDBM3
LD3
LDBM4
LD4
SPARE PARTS LIST
ACCESSORIES
IS 280 ECN 3607 Page 8 of 9
Product code
All available on serial plate
Type number
Serial number
SERVICE INFORMATION
For help with the installation, maintenance and use of your Lincat equipment,
please contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.
To ensure your service enquiry is handled as efficiently as possible, please tell us:
Brief details of the problem
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is
in addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:
Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
Consumable items (such as filters, glass, bulbs, slot toaster elements and door
seals.)
Damage due to incorrect installation, modification, unauthorised service work or
damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.
Service calls to equipment under warranty will be carried out in accordance with the
conditions of sale. Unless otherwise specified, a maximum of 15 minutes of
administrative time, not spent directly carrying out servicing work, is provided for
within the warranty. Any requirement for staff attending the call to spend greater time
than 15 minutes due to administrative requirements, such as on health and safety risk
assessments, will be chargeable at the prevailing rate.
IS 280 ECN 3607 Page 9 of 9
Loading...