Installation, Operating and Servicing
Instructions
Waterboiler EB3FX, EB4FX, EB6FX,
EB6TFX, EB3FX/PB AND EB3FX/TT
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________
IS590 ECN 3846 Page 1 of 12
CONTENTS
Important Information 2
Warnings and Precautions 3
Technical Data 3
Checklist of Enclosures 3
Installation and Commissioning 4
Operating Instructions 5
Cleaning 8
Descaling Servicing, 8
Maintenance and Component Replacement 9
Fault Finding 9
Spare Parts List 9
Accessories 9
Service Information and Guarantee 10
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE
.
IS590 ECN 3846 Page 2 of 12
WARNINGS AND PRECAUTIONS
EB3FX
EB4FX
EB6FX
EB6TFX
EB3FX/PB
EB3FX/TT
This appliance must be installed, commissioned and serviced by a qualified person
in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
TECHNICAL DATA
Height (mm) 600 600 690 690 600 600
Width (mm) 250 250 250 250 250 250
Depth (mm) 525 525 525 525 525 525
Weight (kg) 15 15 18 18 15 16
Power rating(kW) 3 4.5 6 6 3 3
Current rating (A) 13 20 26 26 13 13
CHECK LIST OF ENCLOSURES
Warranty card
Instructions manual
Drip tray
Drip tray insert
Connection hose
Silicone drain hose assembly
IS590 ECN 3846 Page 3 of 12
INSTALLATION AND COMMISSIONING
This appliance must be earthed.
If replacing the plug connect the terminals as follows:
Green and Yellow wire Earth E
Blue wire Neutral N
Brown wire Live L
Means of isolation with at least 3mm contact separation in all poles must be
incorporated into the fixed wiring of EB4FX, EB6FX and EB6TFX appliances.
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)
Install this appliance on a level surface ensuring all vents are unobstructed.
Only install this unit in locations where it can be overseen by trained personnel.
Inlet water pressure should be between 2 and 6 bar. (0.2MPa to 0.6MPa)
Ambient air temperature shall be between 5 and 30 deg C
Electrical supply
The EB3FX series are supplied with a 13 amp plug to BS1363.
The EB4FX is supplied with a bulkhead cable connector. Connect a 2.5mm2 3 core
cable.
The EB6FX and EB6TFX are supplied with a bulkhead cable connector. Connect a
2
4mm
Means of isolation with at least 3mm contact separation in all poles must be
incorporated into the fixed wiring of these appliances.
Water supply and waste connection (All)
Connect the supplied white water inlet hose to the inlet connection point on the
base of the boiler and the other end to the mains supply via an accessible isolating
tap with a ¾” BSP thread.
Use the hose set supplied with the appliance - any previous hose set is not to be reused.
Ensure the metal overflow pipe protrudes through the metal base of the boiler.
Potable water. If solid particles are known to be in the supply, add an extra inline
filter or strainer
3 core cable.
IS590 ECN 3846 Page 4 of 12
OPERATING INSTRUCTIONS
General arrangement
A
B
C
D
E
F
A Tank Cap
B Touchscreen display
C Dispense tap
D Serial plate location
E Water filter
F Lower drain valve (below
slide down cover)
G Drip tray
G
Only qualified or trained personnel should use this appliance.
First Use
Switch on the water and electricity supplies. Leave the boiler to fill for 30 minutes.
New filters have a small amount of loose, harmless, carbon particles. Drain off
approximately 5 litres of water when first setting up or replacing filter.
A new unit starts in a default mode with timers and ECO options turned off.
The unit will display ‘Wait’ whilst it fills and heats. It will display ‘Ready’ when water
can be drawn off.
IS590 ECN 3846 Page 5 of 12
Touchscreen display configuration
C
E
F
G
KEY Pressing allows
A Power button On, off, Timed and ECO modes
B Timed operation Access to timer settings
C ECO operation Access to ECO options
D Clock Access to clock settings
E Ready, Wait Clock, descale, PIN lock and
temperature
F Element on
G Filter life icon Reset filter life after replacement
H Water in
When the boiler is supplied the ECO mode, timed mode and clock function are all
turned off.
To select these options press the “Power button”, select the feature required and
follow the on-screen instructions.
To adjust the temperature, clock or to perform a boiler descale press “Ready”, select
the option and follow the on-screen instructions.
Eco mode only fills the tank to the mid-way point. It reduces the rapid draw-off but
saves energy and reduces heat-up time from cold
A
B
D
H
IS590 ECN 3846 Page 6 of 12
Predictive Eco monitors the boilers usage and decides when the unit should switch in
and out of Eco mode. This is best used with the timed option to save the most amount
of energy.
All units are fitted with a settings PIN lock. Press Ready and then Settings to access
the PIN setting screen. The EB3F/PB is fitted with an extra setting to lock the dispense
tap operation and an additional time setting that is used to set the maximum time after
the last dispense that the boiler is unlocked for. A master PIN code is available from
Lincat Service should you forget the user set PIN.
Filter Replacement
The filter display shows the estimated life remaining in the filter cartridge. A reminder
message is displayed when the filter needs changing.
To replace the filter:
Twist the base of the filter (E) 90 degrees to the left and lower the cartridge out of the
appliance. It will contain a small amount of water.
Insert the new filter into the recess and lock in place by twisting to the right.
Press the “Filter life icon” and follow the on-screen instructions to reset the filter life.
Drain off approximately 5 litres of water to remove any loose carbon particles from the
filter.
The boiler will not fill if the filter is removed as the filter head incorporates a shut-off
valve.
IS590 ECN 3846 Page 7 of 12
CLEANING
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent and do not use abrasive
materials. Dry with a soft cloth.
Slide out and empty the drip tray regularly, and wipe the dispensing tap spout daily
to remove limescale deposits.
DESCALING
De-scaling is an important maintenance task and must be performed to maintain the
warranty.
This range of units has a de-scaling routine built into the software. It guides the user
through the process and advises when to open /close valves and when to add the
de-scaler.
To decide if the boiler needs a de-scale, whilst wearing gloves carefully remove the
blue cap (with the scale dipstick attached) on the top of the boiler.
Allow the water to dry on the dipstick. Where the dipstick has been in the water it will
be covered in the same amount of scale as the rest of the tank. When it is about 0.5 to
1mm thick the tank should be de-scaled.
The de-scale routine takes about an hour to complete and the boiler cannot be used
during the routine.
Lincat offer a purpose designed de-scaler powder, part number DP10 that should be
used.
If there is a fault with the unit it will not be possible to de-scale the unit using the inbuilt programme. The unit will have to be manually chemically de-scaled. Do not
mechanically de-scale with a scraper.
IS590 ECN 3846 Page 8 of 12
Part Number
Description
Used on
EB3FX/PB
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
All maintenance and component replacement on this appliance should be carried
out by one of our recommended service engineers.
FAULT FINDING
Please refer to the Service Help Desk number on the final page of this manual.
SPARE PARTS LIST
For spare parts for your waterboiler please contact the Lincat Spares department on
01522-875510. Refer to the serial plate for the model and serial number of your
waterboiler, as this will help us quickly identify the part you require.
ACCESSORIES
BR55 Wall bracket EB3FX, EB4FX, EB3FX/TT, and
BR56 Wall bracket EB6FX and EB6TFX
FC04 Replacement filter All models
DP10 Descaler powder All models
IS590 ECN 3846 Page 9 of 12
•
•
•
SERVICE INFORMATION
For help with the installation, maintenance and use of your Lincat equipment,
please contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.
To ensure your service enquiry is handled as efficiently as possible, please tell us:
• Brief details of the problem
Product code
Type number
All available on serial plate
Serial number
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty.
This requires you maintain and care for your product and follow maintenance
instructions. If you fail to maintain your unit or damage components Lincat may
charge you for a warranty repair.
The guarantee is in addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:
• Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
• Consumable items (such as filters, glass, bulbs, slot toaster elements and door
seals.)
• Damage due to incorrect installation, modification, unauthorised service work or
damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.
IS590 ECN 3846 Page 10 of 12
Service calls to equipment under warranty will be carried out in accordance with the
conditions of sale. Unless otherwise specified, a maximum of 15 minutes of
administrative time, not spent directly carrying out servicing work, is provided for
within the warranty. Any requirement for staff attending the call to spend greater time
than 15 minutes due to administrative requirements, such as on health and safety risk
assessments, will be chargeable at the prevailing rate.
IS590 ECN 3846 Page 11 of 12
This page intentionally blank
IS590 ECN 3846 Page 12 of 12
Loading...