Lincat CO133M, CO223M, CO133T, CO235M, CO223T Installation, Operating And Servicing Instructions

...

Download

Installation, Operating and Servicing Instructions

CONVECTOR

Electric Convection Ovens

CO133M, CO133T, CO223M, CO223T

CO235M, CO235T

Please make a note of your product details for future use:

Date Purchased:_________________________

Model Number:__________________________

Serial Number:__________________________

Dealer:_________________________________

_______________________________________

IS 731 ECN 4421 Page 1 of 15

CONTENTS

Important Information 2 Warnings and Precautions 3 Checklist of Enclosures 3 Technical Data 3 - 4 Installation and Commissioning 5 Operating Instructions 6 - 10 Fault Finding 10 Cleaning 11 Servicing, Maintenance and Component Replacement 11 - 12 Spare Parts List 13 Accessories 14 Service Information and Guarantee 15

IMPORTANT INFORMATION

Read these instructions carefully before using this product, paying particular attention to all sections that carry warning symbols, caution symbols and notices. Ensure that these are understood at all times

WARNING!

This symbol is used whenever there is a risk of personal injury.

CAUTION!

This symbol is used whenever there is a risk of damaging your Lincat product.

NOTE:

This symbol is used to provide additional information, hints and tips.

KEEP THIS MANUAL FOR FUTURE REFERENCE

IS 731 ECN 4421 Page 2 of 15

WARNINGS AND PRECAUTIONS

This appliance must be installed, commissioned and serviced by a qualified person in accordance with national and local regulations in force in the country of installation.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person.

Ensure that the plug/socket is accessible at all times.

Strip plastic coating and clean the appliance before use.

During operation parts may become hot - avoid accidental contact.

Disconnect this appliance before servicing, maintenance or cleaning.

CHECK LIST OF ENCLOSURES

Instructions Manual Shelves (2 off CO223M, CO223T). Shelves (3 off CO133M, CO133T, CO235M, CO235T). Water connection hose (CO133T, CO223T, CO235T).

TECHNICAL DATA

Model Supply Rating Capacity

CO133M 1P+N+E, 50-60 HZ 3.0kW

CO133T 1P+N+E, 50-60 HZ 3.0kW

CO223M 1P+N+E, 50-60 HZ 3.0kW

CO223T 1P+N+E, 50-60 HZ 3.0kW

1P+N+E, 50-60 HZ

CO235M

CO235T

3P+N+E, 50-60 HZ

1P+N+E, 50-60 HZ 3P+N+E, 50-60 HZ

4.8kW

3 x 2/3GN 3 x 400x300 3 x 460 x 330

2 x 1/1GN 2 x 660x460 2 x 600 x 400

3 x 1/1GN 3 x 660x460 3 x 600 x 400

Tray Spacing

80 55

110 70

90 70.5

Weight (kg)

IS 731 ECN 4421 Page 3 of 15

WATER CONNECTION

VENT

ELECTRICAL CONNECTION

320

610

645

RESET

460

WATER, ELECTRICAL CONNECTIONS

170 410

750

CO1xx VERSIONS

WATER CONNECTION

VENT

ELECTRICAL CONNECTION

850 320

WATER, ELECTRICAL CONNECTIONS

170

510

CO2xx VERSIONS

IS 731 ECN 4421 Page 4 of 15

810

645

RESET

640

INSTALLATION AND COMMISSIONING

This appliance must be earthed.

An equipotential bonding terminal is provided to allow cross bonding with other equipment.

If replacing the plug connect the terminals as follows:

Green and Yellow wire Earth E Blue wire Neutral N Brown wire Live L

Means of isolation with at least 3mm contact separation in all poles must be incorporated into the fixed wiring of the CO235M and CO235T. These units must be connected by a qualified electrician (see power ratings).

The fixed wiring insulation must be protected by insulated sleeving having a temperature rating of 60 Deg C.

Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)

Install this appliance on a level surface ensuring all vents are unobstructed. Any partitions, walls or furniture must be of non-combustible material. Minimum distances A 200mm B 1000mm – see Fig 1. Leave 100mm for services.

An air filter will need occasional access. (See Fig 3 for position).

The water supply pressure must be from 2 - 6 bar (200kPa-600kPa). Lincat recommend that a water filter should be installed. Refer to Lincat’s website for the recommended option

IS 731 ECN 4421 Page 5 of 15

Fig 2

OPERATING INSTRUCTIONS

Only qualified or trained personnel should use this appliance.

MODELS CO133M, CO223M and CO235M

A- On/Off E- Fan Speed B- Power supply indicator F- 120 minute timer C- Oven heating indicator G- Reset D- Temperature control knob H- Filter

Fig 3

Connect the appliance to the electricity supply. The green neon (A) illuminates indicating power to the appliance. Select the On/Off switch, the switch will illuminate and the fan will start rotating.

Select the desired fan speed, slow or fast.

Set the thermostat to the desired temperature, the amber neon will indicate that the unit is heating.

When at the set temperature the amber light will turn off and will alternate on or off to maintain the set temperature.

Load products onto the shelves and if required set the timer.

When the set time expires the buzzer/lights will sound/flash.

Carefully open the door and remove the cooked products. Opening the door will cancel the buzzer and flashing lights.

IS 731 ECN 4421 Page 6 of 15

Note: When the door is opened, if the fan is set to fast speed, the fan will switch from fast to slow speed and return to fast speed when the door is closed.

To turn the unit off set the temperature control knob to the off position and switch off at the mains.

MODELS: CO133T, CO223T and CO235T

A- Touch Screen

C- USB

B- Reset D- Filter

Fig 4

Only qualified or trained personnel should use this appliance.

Connect the appliance to the electricity supply. The unit will beep once and will self-test the elements and fans. The screen will show the CONVECTOR logo and then go to the home screen.

Refer to the Programming guide for the user interface operation and programming.

To use the unit simply select the correct program. The unit will Pre-heat to the set temperature and beep when ready to be loaded with product.

Place the food in the oven and press cook. The oven will cook the food and when the set time expires the buzzer/lights will sound/flash. On screen timers will also indicate the timer has expired.

Press done and remove the food from the oven.

To adjust the clock settings go to the home screen, click on the clock in the top right corner, select the hours or minutes to change, adjust and save.

IS 731 ECN 4421 Page 7 of 15

Move

Home

Oven mode

Recipe

Manager

Standby

Machine

Move and

recipes

Select recipe

How to programme your Touch screen Convector

(COxxxT models).

Home screen

This is where you run recipes from (just press the recipe you want). You can switch into the oven mode from here. Pressing recipe manager takes you into the programming area

settings

Recipe Manager

This lets you select a recipe to edit (just press the recipe). Here you can also reassign the order recipes are presented in, access further oven settings and run updates

reorder your

to edit

IS 731 ECN 4421 Page 8 of 15

Return to

home

Change icon

Return to recipe

Save

Steps

touch to

recipe steps

Humidity

Injection settings

Fan speed

Adjust the fan s

peed and humidity injection.

Return to recipe

Tap the end of the bar for small increments,

manager

Recipe summary and edit screen

This is where you view your recipe with changes highlighted in green. Press on the steps to edit them. Press on the name bar to rename the recipe. Attach or change an icon from the library. Click on to save to keep your recipe. Or exit without saving.

add or edit

settings

Home

summary

Recipe summary and edit screen

This is where you adjust the times, temperature and set humidity injection and fan speeds. The recipe summary button takes you back to the summary screen so you can review changes and save.

The humidity injection occurs at the start of each stage

Touch time or temp then adjust with the slider

Move between steps If you are ready to review the changes press the recipe summary button and save or exit

IS 731 ECN 4421 Page 9 of 15

swipe for large increments

Return to

home

Tap to see actual

Touch to

Temperature

setting

Fan speed

Humidity injection

Single or 4

temperature

enter time

Timer screen

In oven mode you can change the temperature and run up to 4 count down timers. Alternatively don’t enter a time and it will maintain the set temperature indefinitely.

The fan speed can be increased or decreased. A humidity injection level can be set (this then operates in 30 second steps at the beginning of the programmed cycle).

level settings

shelf timer mode

Humidity can be added by pressing the humidity injection setting. In oven mode humidity is added on demand. In program mode it is injected at the start of each step.

Higher levels of humidity can be achieved by incorporating additional steps in the cooking program and adding humidity within these steps.

Humidity injection levels can be set from 1 – 5.

FAULT FINDING

This appliance is fitted with a safety thermostat, which will cut power to the appliance under fault conditions. If when turning the unit on it fails to operate firstly check the power supply to the unit then the reset before contacting Lincat service.

IS 731 ECN 4421 Page 10 of 15

To re-set the safety thermostat, firmly push the red button which is recessed under the front edge of the unit see (Fig 3 – 4). This re-set cannot be activated until the appliance is cool. If this continues to happen please call our service department.

Please refer to the Service Help Desk number on the final page of this manual.

CLEANING

Your product has a manufacturer’s warranty. This requires you maintain and care for your product and follow maintenance instructions. If you fail to maintain your unit or damage components Lincat may charge you for a warranty repair. Please check the website for terms and conditions.

Do not use a water jet or steam cleaner, and do not immerse this appliance.

Clean all panels with warm water and mild detergent, do not use abrasive materials.

Dry with a soft cloth.

Please refer to the Lincat website for the recommended cleaning products.

Avoid damaging the thermostat bulbs inside the oven when cleaning.

To assist cleaning remove shelf supports – see Servicing.

SERVICING, MAINTENANCE AND COMPONENT REPLACEMENT

All servicing, maintenance and component replacement on this appliance should be carried out by one of our recommended service engineers.

Regularly check the filter, see Fig 3 or 4, on the right hand side of the unit. It may be cleaned in a dishwasher. Allow to fully dry before re-fitting.

Do not use the unit without the filter.

The door seal and bulbs are considered consumable parts and are not covered by the warranty. The door seal on all units and the bulbs on the COxxxM units are customer replaceable part. COxxxT bulbs require a screwdriver and disassembly of the light housing to replace. Lincat recommend a qualified person undertakes this operation.

IS 731 ECN 4421 Page 11 of 15

Door inner glass removal and refitting

With the door open, hold the lower edge of the inner glass and one of the metal tabs at the top. Carefully pull the glass towards you whilst lifting the metal tab. With the glass now free at the top, lift the glass panel clear.

To refit, position onto the locating pins on the lower edge and close against the upper locating pins.

Pull the tabs towards you until the glass drops onto the upper locating pins then push to engage.

Light bulb replacement

Mechanical units.

Carefully remove the glass cover and using a flat bladed screwdriver. Remove the bulb. Fit new bulb and replace cover.

Touch units.

Remove four screws holding the cover plate, carefully remove the cover plate, gasket and glass lens. Remove the bulb. Fit new bulb and re-assemble.

Shelf racks removal and refitting

See Fig 5 (Door removed for clarity).

TURN TO UNDO

Fig 5

IS 731 ECN 4421 Page 12 of 15

LIFT TO REMOVE

TURN TO UNDO

Part Number

Description

Used on

SPARE PARTS LIST

You can search for your spare parts on Lincat.co.uk using your products serial number.

CA208 Run Capacitor All Models CO215 Contactor CO235M, CO235T EL332 3.0 Kw Element CO133M, CO133T, CO223M, CO223T EL330 4.5 Kw element CO235M, CO235T GL705/S Inner glass CO133M, CO133T GL703/S Inner glass CO223M, CO223T, CO235M, CO235T HI189 RH Door Hinge All Models HI190 LH Door Hinge All Models HI191 Door Hinge Roller All Models IMP02 Impellor All Models LE85 Adjustable Leg All Models MO31 Bi-Directional Motor All Models KN526 Control Knob CO133M, CO223M, CO235M KN527 120 minute timer knob CO133M, CO223M, CO235M NE46 Green neon CO133M, CO223M, CO235M NE47 Amber neon CO133M, CO223M, CO235M PI12 Inlet connection hose CO133T, CO223T, CO235T PL306 Plug and lead CO133M, CO133T, CO223M, CO223T SE92 Door seal CO133M, CO133T SE93 Door seal CO223M, CO223T, CO235M, CO235T SH137 Shelf CO223M, CO223T, CO235M, CO235T SH138 Shelf CO133M, CO133T SO23 Solenoid valve CO133T, CO223T, CO235T

SW34 Fan speed switch CO133M, CO223M, CO235M X54900 Door switch All Models SW97 On/Off switch CO133M, CO223M, CO235M TC47 Thermocouple CO133T, CO223T, CO235T TH46 Thermostat CO133M, CO223M, CO235M TH203 Safety Cut out All Models TI56 120 minute timer CO133M, CO223M, CO235M TS04 Thumb screw All Models FAS250 Knob clip CO133M, CO223M, CO235M BU227 Oven light bulb All Models

IS 731 ECN 4421 Page 13 of 15

Part

Descripti

on Used on

ACCESSORIES

Number

CO100/FS Floor stand

6 runners

CO200/FS Floor stand

6 runners

CO100/LFSK Low floor stand

and stacking kit

CO200/LFSK Low floor stand

and stacking kit

ACIK03 Compact filter kit, 300 litre life. Suitable for most

installations.

ACIK04 Standard filter kit, 1500 litre life CO133T,

2/3 GN, 400 x 300 Baking Sheets 460 x 330 Baking Sheets 1/1 GN, 600 x 400 Baking Sheets 660 x 460 Baking Sheets

Stand and oven vent kit CO133M,

Stand and oven vent kit CO223M,

CO133M, CO133T

CO223M, CO223T, CO235M, CO235T

CO133T

CO223T, CO235M, CO235T CO133T, CO223T, CO235T

CO223T, CO235T

SERVICE INFORMATION

For help with the installation, maintenance and use of your Lincat equipment, please contact our service department:

IS 731 ECN 4421 Page 14 of 15

For non-UK customers, please contact your local Lincat dealer

•

All service work, other than routine cleaning should be carried out by one of our authorised service agents. We cannot accept responsibility for work carried out by other persons.

To ensure your service enquiry is handled as efficiently as possible, please tell us:

• Brief details of the problem Product code Type number Serial number

Lincat reserve the right to carry out any work under warranty, given reasonable access to the appliance, during normal working hours, Monday to Friday, 08:30 to 17:00.

GUARANTEE

This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is in addition to, and does not diminish your statutory or legal rights.

 UK: 01522 875520

All available on serial plate

The guarantee does not cover:

• Accidental damage, misuse or use not in accordance with the manufacturer’s

instructions

• Consumable items (such as filters, glass, bulbs, slot toaster elements and door

seals.)

• Damage due to incorrect installation, modification, unauthorised service work or

damage due to scale, food debris build-up, etc.

The manufacturer disclaims any liability for incidental, or consequential damages.

Attendance is based on reasonable access to the appliance to allow the authorised technician to carry out the warranty work.

Service calls to equipment under warranty will be carried out in accordance with the conditions of sale. Unless otherwise specified, a maximum of 15 minutes of administrative time, not spent directly carrying out servicing work, is provided for within the warranty. Any requirement for staff attending the call to spend greater timethan 15 minutes due to administrative requirements, such as on health and safety risk assessments, will be chargeable at the prevailing rate.

IS 731 ECN 4421 Page 15 of 15

Lincat CO133M, CO223M, CO133T, CO235M, CO223T Installation, Operating And Servicing Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual