Lincat D3H, D3H/75, D5H, C6H, D5H/75 Installation, Operating And Servicing Instructions

...

IS 282 ECN 3607 Page 1 of 8

Installation, Operating and Servicing Instructions

Seal Heated Merchandisers C6H, D3H and D5H – all models

Please make a note of your product details for future use:

Date Purchased:_________________________ Model Number:__________________________ Serial Number:__________________________ Dealer:_________________________________ _______________________________________

IS 282 ECN 3607 Page 2 of 8

CONTENTS

Important Information

Warnings and Precautions

Technical Data

Checklist of Enclosures

Installation and Commissioning

3-4

Operating Instructions

5-6

Cleaning

6-7

Servicing, Maintenance and Component Replacement

Fault Finding

Spare Parts List

Service Information and Guarantee

IMPORTANT INFORMATION

Read these instructions carefully before using this product, paying particular attention to all sections that carry warning symbols, caution symbols and notices. Ensure that these are understood at all times.

WARNING!

This symbol is used whenever there is a risk of personal injury.

CAUTION!

This symbol is used whenever there is a risk of damaging your Lincat product.

NOTE:

This symbol is used to provide additional information, hints and tips.

KEEP THIS MANUAL FOR FUTURE REFERENCE

IS 282 ECN 3607 Page 3 of 8

WARNINGS AND PRECAUTIONS

This appliance must be Installed, Commissioned and Serviced by a qualified person in accordance with national and local regulations in force in the country of installation.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person.

Ensure that the plug/socket is accessible at all times.

Strip plastic coating and clean the appliance before use. During operation parts may become hot - avoid accidental contact. Disconnect this appliance before servicing, maintenance or cleaning.

TECHNICAL DATA

D3H/75

D5H/75

D5H/100

C6H/75

C6H/100

Volume (l)

113.0

163.0

220.0

284.0

380.0

Width (mm)

750

1000

750

1000

Depth (mm)

350

500

650

Height (mm)

575

755

Weight (kg)

34.0

43.0

55.0

57.0

71.0

Power rating (kW)

0.8

1.5

2.0

1.5

2.0

CHECK LIST OF ENCLOSURES

Warranty card

Instructions manual

Shelves

Base plate(s)

Crumb tray

Water bath and lid

3mm Allen key

INSTALLATION AND COMMISSIONING

This appliance must be earthed.

IS 282 ECN 3607 Page 4 of 8

An equipotential bonding terminal is provided to allow cross bonding with other equipment.

If replacing the plug connect the terminals as follows: Green and Yellow wire Earth E Blue wire Neutral N Brown wire Live L

Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary

polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)

Install this appliance on a level surface ensuring all vents are unobstructed. Any

partitions, walls or furniture must be of non-combustible material. Minimum

distances A 100mm B 500mm – see Fig 1.

Fig 1

IS 282 ECN 3607 Page 5 of 8

OPERATING INSTRUCTIONS

Only qualified or trained personnel should use this appliance.

This appliance relies on the circulation of warm air passing through and around the

shelves. Ensure circulation is not obstruct by overloading product or by using

aluminium foil.

This appliance is intended for displaying pre-heated food – not for heating

food.

Fig 2

Identification (Fig 2)

1. Cable 2. On/Off switch 3. Light switch 4. Temperature controller 5. Crumb tray

/ Water bath

Ensure the base plates lie flat within the base and the shelves are secure. Close all

doors – front and rear. Connect to the electricity supply, switch on the light (3) then

switch on the ‘On/Off’ switch (2). C6 appliances are factory set to 85 Deg C. Press

and hold the ‘Set’ button to confirm this.

IS 282 ECN 3607 Page 6 of 8

D3 and D5 models have a manual temperature control (4). Turn to setting 5 and

wait 30 minutes before loading with pre-heated food. Adjust the temperature as

required.

C6 models have a digital display controller (4). Wait 30 minutes until the display

shows 85 Deg C. Load with pre-heated food. Adjustment between 75-95 Deg C is

available by pressing and holding the ‘Set’ button and using the buttons marked <<-

< and >->>.

Note: The temperature display relates to the air temperature inside the

cabinet – not the food temperature.

Humidity feature - Fig 3

Fig 3

The integral water bath B with lid A is intended to be used to keep food moist when

the appliance is lightly loaded. Fill with warm water. To prevent condensation, do

not over-load shelves with food. Check the water level – be aware the water bath

will become hot during use.

Adjusting shelf positions

Disconnect from electricity supply and allow appliance to cool. Slide the doors to

the centre and lift up and out of the bottom runners to remove. Remove the

shelves. Use the Allen key provided to adjust the shelf supports. At the rear, the

shelf supports are situated behind the cable panel. Remove the screws in the cable

panel and open the panel until adjustment of the shelf supports can be made. Do

not completely remove the cable panel. Replace the panel, ensuring cables are

not trapped.

CLEANING

Do not use a water jet or steam cleaner, and do not immerse this appliance.

IS 282 ECN 3607 Page 7 of 8

Remove the rear doors, shelves and base plates. Brush crumbs into the tray Fig 3 C. Shelves and supports may be washed in a dishwasher.

Clean all panels with warm water and mild detergent, do not use abrasive materials.

Dry with a soft cloth.

SERVICING, MAINTENANCE AND COMPONENT REPLACEMENT

Replacing a light tube

Disconnect the appliance from the supply. Allow tube to cool. Use the Allen key provided to remove the end caps from the light unit. Remove the diffuser from the clips. Rotate the tube 900 and pull down until released. Replace the starter if necessary by rotating anticlockwise and removing. Fit the new tube by reversal of the above sequence.

All other servicing, maintenance and component replacement on this appliance

should be carried out by one of our recommended service engineers.

Please refer to the Service Help Desk number on the final page of this manual.

Part Number

Description

Used on

BU171

Light tube

All

EL218

Element

EL162 (75 models)

Element

D5 C6 EL161 (100 models)

Element

GL68

Starter

All

HP17 (75 models)

Base plate

HP18 (100 models)

Base plate

HP19 (100 models)

Base plate

HP20 (75 models)

Base plate

HP21

Base plate

KN203

Control knob

D3 D5

SH93

Shelf

SH91(75 models)

Shelf

SH92 (100 models)

Shelf

SH97 (75 models)

Shelf

SH98 (100 models)

Shelf

S/M0085

Self service door knob

D5 C6

FAULT FINDING

SPARE PARTS LIST

IS 282 ECN 3607 Page 8 of 8

For help with the installation, maintenance and use of your Lincat equipment,

please contact our service department:

 UK: 01522 875520

For non-UK customers, please contact your local Lincat dealer

All service work, other than routine cleaning should be carried out by one of our

authorised service agents. We cannot accept responsibility for work carried out by

other persons.

To ensure your service enquiry is handled as efficiently as possible, please tell us:

 Brief details of the problem

 Product code

All available on serial plate

 Type number

 Serial number

Lincat reserve the right to carry out any work under warranty, given reasonable

access to the appliance, during normal working hours, Monday to Friday, 08:30 to

17:00.

GUARANTEE

This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is

in addition to, and does not diminish your statutory or legal rights.

The guarantee does not cover:

 Accidental damage, misuse or use not in accordance with the manufacturer’s

instructions

 Consumable items (such as filters, glass, bulbs, slot toaster elements and door

seals.)

 Damage due to incorrect installation, modification, unauthorised service work or

damage due to scale, food debris build-up, etc.

The manufacturer disclaims any liability for incidental, or consequential damages.

Attendance is based on reasonable access to the appliance to allow the authorised technician to carry out the warranty work.

Service calls to equipment under warranty will be carried out in accordance with the conditions of sale. Unless otherwise specified, a maximum of 15 minutes of administrative time, not spent directly carrying out servicing work, is provided for within the warranty. Any requirement for staff attending the call to spend greater time than 15 minutes due to administrative requirements, such as on health and safety risk assessments, will be chargeable at the prevailing rate.

SERVICE INFORMATION

Lincat D3H, D3H/75, D5H, C6H, D5H/75 Installation, Operating And Servicing Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual