Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________
Installation, Operating and Servicing
Instructions
Silverlink 600 Vertical Travel Salamanders
AS3, AS4
IS 384 ECN 3607 Page 1 of 10
CONTENTS
Important Information
2
Warnings and Precautions
3
Technical Data
3
Checklist of Enclosures
3
Installation and Commissioning
3 - 6
Operating Instructions
6
Cleaning
7
Servicing, Maintenance and Component Replacement
8
Fault Finding
8
Spare Parts List
8
Accessories
8
Service Information and Guarantee
9
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE
IS 384 ECN 3607 Page 2 of 10
WARNINGS AND PRECAUTIONS
TECHNICAL DATA
Model
Height (mm)
Width (mm)
*Depth (mm)
Weight (kg)
AS3
500
600
550 (inc. handle)
45.0
AS4
500
600
550 (inc. handle)
47.5
CHECK LIST OF ENCLOSURES
Warranty Card
Instructions Manual
Drip / crumb tray
Wire tray
Wire support rack
Heat shield
INSTALLATION AND COMMISSIONING
This appliance must be installed, commissioned and serviced by a qualified person
in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
*NB. Appliances are 640mm deep when wall mounted.
This appliance must be earthed.
An equipotential bonding terminal is provided to allow cross bonding with other
equipment.
IS 384 ECN 3607 Page 3 of 10
If replacing the plug connect the terminals as follows:
Model
Supply Requirement
Supply Connection
Power Rating (kW)
AS3
Single phase 11.7 A
Single phase 13A plug
2.8
AS4
Single phase 19.5 A
5 way terminal block
4.5
Green and Yellow wire Earth E
Blue wire Neutral N
Brown wire Live L
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)
Power Ratings
Model AS3 is fitted with a 3 pin plug for connection to a standard switched socket.
Model AS4 must be connected by a qualified electrician.
Means of isolation with at least 3mm contact separation in all poles must be
incorporated into the fixed wiring of the AS4.
The fixed wiring insulation must be protected by insulated sleeving having a
temperature rating of at least 60 Deg C.
Appliances may be counter or wall mounted. For either installation, remove and
discard the 2 transportation screws (A) from rear panel. (Fig 2).
Counter Mounted
Install this appliance on a level surface ensuring all vents are unobstructed. Any
partitions, walls or furniture must be of non-combustible material and not be closer
than 300 mm (Fig 1 A). Dimension B 60mm minimum – 220mm maximum.
Dimension C depth when wall mounted.
Ensure a space of at least 500 mm between the working surface and any ceiling.
IS 384 ECN 3607 Page 4 of 10
Fig 1
Wall Mounted (Brackets required – see accessories)
Use clearance dimensions as for counter mounted.
Unscrew bolts 1-4 (Fig 2) half a turn.
Fig 2
Measure and drill holes for wall mounting brackets (Fig 3). Bolt brackets to wall.
Fig 3
IS 384 ECN 3607 Page 5 of 10
Lift appliance into position, locating screws 1-4 (Fig 2) into keyways on brackets
OPERATING INSTRUCTIONS
(Fig 4).
Fig 4
Push back (1) and push down (2) until appliance locks into place.
Only qualified or trained personnel should use this appliance.
Raise element hood to highest position.
Switch on appliance – On/Off switch will illuminate.
Allow 15 minutes to warm up.
Place plates or dishes onto grill tray.
Adjust height of hood to desired position.
Never operate with hood in lowest position for more than 30 minutes.
Avoid contact between food and the element.
Audible timer does not control the power; appliance must be switched off using the
switch.
IS 384 ECN 3607 Page 6 of 10
CLEANING
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent, do not use abrasive
materials. Dry with a soft cloth.
In extreme conditions, a branded cleaner such as ‘Carbon Off’ may be used.
The wire grid, drip tray and tray support frame are removable for cleaning. When
re-assembling, ensure the stop pins (A) beneath the drip tray are located behind the
front uprights (B) of the fixed tray runners (C) to avoid the tray tipping when drawn
forward. (Cut-away view – Fig 5).
Fig 5
IS 384 ECN 3607 Page 7 of 10
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
Part Number
Description
Used on
CB10
Counterweight
AS3
CB11
Counterweight
AS4
CO215
Contactor
AS4
EC04
Handle end cap
AS3, AS4
EL50
Element
AS3
EL237
Element
AS4
FE35
Foot
AS3, AS4
KN163
Knurled Knob – top heat shield
AS3, AS4
KN272
Knob - timer
AS3, AS4
PL202
Mains cable & plug
AS3
RO135
Nylon roller – counterbalance strap
AS3, AS4
SS05
Nylon support strap
AS3, AS4
SW69
On/Off switch
AS3, AS4
TE10
Small terminal block
AS3, AS4
TE45
Large terminal block
AS4
TI38
Timer
AS3, AS4
TU105
Handle tube
AS3, AS4
WI16
Wire tray runner
AS3, AS4
WI17
Wire tray support
AS3, AS4
WI18
Wire tray grid
AS3, AS4
FAULT FINDING
SPARE PARTS LIST
There are no recommended user servicing instructions for these appliances. All
servicing, maintenance and component replacement on these appliances should be
carried out by one of our recommended service engineers.
Please refer to the Service Help Desk number on the final page of this manual.
IS 384 ECN 3607 Page 8 of 10
Part Number
Description
Used on
BR41
Wall mounting bracket
AS3
BR51
Wall mounting bracket
AS4
ACCESSORIES
IS 384 ECN 3607 Page 9 of 10
Product code
All available on serial plate
Type number
Serial number
SERVICE INFORMATION
For help with the installation, maintenance and use of your Lincat equipment,
please contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.
To ensure your service enquiry is handled as efficiently as possible, please tell us:
Brief details of the problem
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is
in addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:
Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
Consumable items (such as filters, glass, bulbs, slot toaster elements and door
seals.)
Damage due to incorrect installation, modification, unauthorised service work or
damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.
Service calls to equipment under warranty will be carried out in accordance with the
conditions of sale. Unless otherwise specified, a maximum of 15 minutes of
administrative time, not spent directly carrying out servicing work, is provided for
within the warranty. Any requirement for staff attending the call to spend greater time
than 15 minutes due to administrative requirements, such as on health and safety risk
assessments, will be chargeable at the prevailing rate.
IS 384 ECN 3607 Page 10 of 10
Loading...