Linak CBD6S 200W, DESKLINE DL2, CBD6S 300W, DP1U, DPF1M User Manual

Page 1 of 24

U S E R MA N U A L

DL2 and CBD6S systems

To learn more about LINAK please visit:

WWW . L I N AK . C O M

Page 2 of 24

Page 3 of 24

Contents

Preface

..............................................................................................................................................................4

Valid for ................................................................................................................................................. 5

Important information.......................................................................................................................... 6

Safety instructions ............................................................................................................................... 6

General ......................................................................................................................................................6

Before installation, reinstallation or troubleshooting ....................................................................... 7

Before start-up...........................................................................................................................................7

During operation ............................................................................................................................. 7

Misc................................................................................................................................................. 7

Only for EU markets ..................................................................................................................................8

Only for Non EU markets ..........................................................................................................................8

Misuse .......................................................................................................................................................8

Repairs

.............................................................................................................................................................9

Manufacturer’s declaration ................................................................................................................. 9

Misc. on the DESKLINE® system

....................................................................................................... 10

Warranty ...................................................................................................................................... 10

Maintenance ................................................................................................................................ 10

ETL-markering ................................................................................................................................... 11

Description of the DESKLINE

®

system

............................................................................................. 12

Mounting guidelines for DL2 ........................................................................................................... 13

Bending moment ............................................................................................................................... 14

Mounting guidelines CBD6S (SMPS)

................................................................................................ 15

Electrical connection of the DL2 with control box

.......................................................................... 16

Initialisation of the DL2 with control box ....................................................................................... 17

Disposal of LINAK’s products

............................................................................................................ 18

Labels

................................................................................................................................................. 19

Drawing appendix ............................................................................................................................. 20

Declaration of conformity ................................................................................................................ 23

Addresses

........................................................................................................................................... 24

Page 4 of 24

Preface

We are delighted that you have chosen a product from LINAK A/S. LINAK systems are high-tech products
based on many years of experience in the manufacture and development of actuators, electric control boxes,
controls, and chargers.

We are also constantly improving our products to meet customer requirements.
This User Manual will tell you how to install, use and maintain your LINAK DESKLINE® products.
We are sure that the DESKLINE® products will give you many years of problem-free operation. Before our

products leave the factory they undergo full function and quality testing. Should you nevertheless experience
problems with your systems, you are always welcome to contact our service departments or service centres.

LINAK subsidiaries and distributors all over the world have authorised service centres, which are always ready
to help you.

LINAK provides a warranty on all its products. This warranty, however, is subject to correct use in accordance
with the specifications, maintenance being done correctly and any repairs being carried out at a service
centre, which is authorised to repair LINAK products.

Changes in installation and use of LINAK systems can affect their operation and durability. Changes must
therefore only be made by agreement with LINAK A/S and are made at your own risk.

LINAK A/S

Page 5 of 24

Valid for:

This User Manual is valid for the following products:

(See the first 3 - 5 characters on the label)

Lifting columns: DL2

Control boxes: CBD6S 200W, CBD6S 300W

Controls: DP1U/DPF1M (if memory function is required)

DP1C/DPT/DPF1C (if memory function and display is required) or
DPA/DPB/DPH/DP1K/DP1V/DPF1K (if only up/down is required.)

Page 6 of 24

Important information

Important information on LINAK® products can be found under the
following headings:

Warning!

Failure to comply with these instructions may result in accidents
involving serious personal injury.

Failing to follow these instructions can result in the product being
damaged or being destroyed.

Safety instruction
General

Safe use of the system is possible only when the operating instructions
are read completely and the instructions contained are strictly observed.

Failure to comply with instructions marked with the ”NOTE” symbol may
result in serious damage to the system or one of its components.

It is important for everyone who is to connect, install, or use the
systems to have the necessary information and access to this User
Manual. Follow the instructions for mounting – risk of injury if these
instructions are not followed.

The appliance is not intended for use by young children or infirm
persons without supervision.

If there is visible damage on the product it must not be installed.
Note that during construction of applications, in which the actuator

is to be fitted, there must be no possibility of personal injury, for
example the squeezing of fingers or arms.

Assure free space for movement of application in both directions to
avoid blockade.

Page 7 of 24

Before installation, re-installation, or troubleshooting

•

Stop the DL2

•

Switch off the power supply and pull out the mains plug.

•

Relieve the DL2 of any loads, which may be released during the work.

Before start-up:

•

Make sure that the system has been installed as instructed in this User
Manual.

•

Make sure that the voltage of the control box is correct before the
system is connected to the mains.

•

System connection. The individual parts must be connected before the
control box is connected to the mains. See the User Manual for LINAK
actuators, if necessary.

During operation:

•

If the control box makes unusual noises or smells, switch off the mains
voltage immediately.

•

Take care that the cables are not damaged.

•

Unplug the mains cable on mobile equipment before it is moved.

•

The products must only be used in an environment, that corresponds
to their IP protection.

Misc.

The actuator system has a sound level below 55dB(A) in typical
applications.

Updated manuals and declarations can always be found here:

www.linak.com/deskline

Page 8 of 24

Only for EU markets

This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have given
supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.

Only for Non EU markets

Persons who do not have the necessary experience or knowledge of
the product/products must not use the product/products. Besides,
persons with reduced physical, sensory or mental abilities must not
use the product/products, unless they are under surveillance or they
have been thoroughly instructed in the use of the apparatus by a
person who is responsible for the safety of these persons.

Moreover, children must be under surveillance to ensure that they
do not play with the product.

It is the operator’s responsibility to ensure that there is free space for
the application to move without risk for the operator or bystanders
before operating the application.

Misuse

Do not overload the actuators – this can cause danger of personal
injury and damage to the system.

Do not use the actuator system for lifting persons. Do not sit or
stand on a table while operating – risk of personal injury.

Do not use the system in environments other than the intended
indoor use

Page 9 of 24

Repairs

In order to avoid the risk of malfunction, all DESKLINE® repairs must only be carried out by authorised LINAK
workshops or repairers, as special tools must be used and special gaskets must be fitted. Lifting units under
warranty must also be returned to authorised LINAK workshops.

Warning!

If any of the DESKLINE® products are opened, there will be a risk of subsequent malfunction.

Warning!

The DESKLINE® systems do not withstand cutting oil.

DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY

LINAK A/S

Smedevænget 8

DK - 6430 Nordborg

Herewith declares that LINAK DESKLINE® products as characterized by the following models and types:

Control Boxes CBD4, CBD5, CBD6, CBD6S

And
Linear Actuators LA31, DB4, DB5, DB6, DB7, DB9, DB12, DB14, DB16, LA23
Lifting Columns DL1A, DL2, DL4, DL5, DL6, DL7, DL8, DL9, DL10, DL11, DL12, DL14, DL15,

DL16, DL17, LP2, LP3, BASE1

And
Desk Panels DP, DPA, DPB, DPH, DPF, DPT, DP1C, DP1K, DP1L, DP1V, DP1U, WDPL1
RF Controls HB10, HB20, RFR and RFT

And
Accessories SLS

comply with the following parts of the Machinery Directive 2006/42/EC, ANNEX I, Essential health and
safety requirements relating to the design and construction of machinery:

1.5.1 Electricity supply

The relevant technical documentation is compiled in accordance with part B of Annex VII and that this
documentation or part hereof will be transmitted by post or electronically to a reasoned request by the
national authorities.

This partly completed machinery must not be put into service until the final machinery into
which it is to be incorporated has been declared in conformity with the provisions of the
Machinery Directive 2006/42/EC where appropriate.

Nordborg, 2014-04-10

LINAK A/S

John Kling, B.Sc.E.E.
Certification and Regulatory Affairs
Authorized to compile the relevant technical documentation

Page 10 of 24

Misc. on the DESKLINE® system

Warranty

There is a 36 months’ warranty on the DESKLINE products against manufacturing faults from the production
date of the individual products (see label).
LINAK A/S’ warranty is only valid in so far as the equipment has been used and maintained correctly and has
not been tampered with. Furthermore, the system must not be exposed to violent treatment. In the event of
this, the warranty will be ineffective/invalid. For further details, please see LINAK A/S ordinary conditions of
sale.

Maintenance

Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for damage and
breaks.
Inspect the connections, cables, and plugs and check for correct functioning as well as fixing points.

Service of double-insulated products:

Class II

A Class II or

double insulated

electrical appliance is one which has been designed in such a way that it does
not require a safety connection to electrical earth (US: ground).
The basic requirement is that no single failure can result in dangerous voltage becoming exposed so that it
might cause an electric shock and that this is achieved without relying on an earthed metal casing. This is
usually achieved at least in part by having two layers of insulating material surrounding live parts or by using
reinforced insulation.
There is no earthing/grounding means provided on the product, and no earthing/grounding means is to be
added to the product.
In Europe, a double insulated appliance must be labelled “Class II”, “double insulated” or bear the double
insulation symbol (a square inside another square).
Servicing a double-insulated product requires extreme care and knowledge of the system, and is to be done
only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the
parts they replace.

The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).

Page 11 of 24

ETL-marking

Due to space limitations, the complete ETL-marking demands are not represented on the marking plates.
The full ETL Recognized Component markings are shown here.

C/N 120690

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United
States

C/N 9901916

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United
States

C/N 4008003

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United States

C/N 4008004

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United States

C/N 4008005

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United States

C/N 4008671

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United States

C/N 4009507

Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09

ETL Recognized Component mark for Canada and United States

Page 12 of 24

Description of the DESKLINE® system

Each DESKLINE® actuator/column is equipped with a motor and parallel/memory drive is ensured by means of
software in the CBD6S that also takes account of an uneven load on the desk. Soft start and stop are also
part of this software, which ensures a soft start and stop when adjusting the desk.

Application of the DESKLINE® system:

Irrespective of the load the

duty cycle max. 5% ~ 1 min./ 19 min., max. 1 min. at continuous use

followed by 19 min. pause

stated in the data sheets, must

NOT

be exceeded as this will result in an
overheating of the motor and control box. Exceeding the duty cycle will result in a dramatic reduction of the
life of the system.

The system range contains the following products:

•

1 control box CBD6S 200W or CBD6S 300W (SMPS - Switch Mode Power Supply)

•

1, 2, 3 or 4 DL2 lifting columns

•

1 exchangeable mains cable

•

motor cables (1 - 4 (4))

•

1 DP1U/DPF1M (if memory function is required) DP1C/DPT/DPF1C (if memory function and display is
required) or 1 DPA/DPB/DPH/DP1K/DP1V/DPF1K (if only up/down is required.)

Page 13 of 24

Mounting guidelines for DL2

The DL2 column is supplied with either 8 mm end plates or 3 mm end plates.
8 mm end plates:

For mounting on the desk frame there are 4 holes for M10 bolts. It is recommended to use all 4 bolts.
3 mm end plates:

For mounting on the desk frame there are 4 holes in the column for DG 80 x 35 screws. It is recommended to
use all 4 screws.

As the table top amplifies the sound we advise you to place a vibration/shock-absorbing material between
the table top and the table frame.

The outer profile of the DL2 column has tracks, which can be used for mounting a bracket. The mounting
bracket can be used for e.g.:

Mounting a customised cover (for encapsulation of the DL2).
Mounting of a computer

Figure 1

Example of how to mount a DL2 system

Page 14 of 24

Bending moment

Spindle top

Y+

X-

X+

Y-

Figure 2

To limit the influence from the bending moment it is recommended to place the heaviest load in the shaded
area (see figure 2) in which the spindle is placed. The spindle part is placed in the same side as the cable
outlet.
See the DL2 data sheet for further information regarding bending moment.

LINAK recommends that the DESKLINE® system should be used in push applications.

Page 15 of 24

Mounting guidelines CBD6S (SMPS)

The control box is to be fastened with 2 screws with a head diameter between ø 8 and ø 10 mm. Out of
regard for the tension surface ø 10 mm is preferable due to lower surface tension. See drawing appendix for
placing of mounting holes and the space the CBD takes up.

CBD6S 200W and CBD6S 300W

The CBD must not be packed in heat insulating material, but must be placed so that it can emit waste heat
into the surroundings. There are no ventilation holes to consider, the CBD emits heat through the surface.
The plug must be visible when the CBD is mounted so that the supply to the CBD can be disconnected at
replacement, if any.
The mounting screws on the control box must be fastened with a max. torque of 1 Nm.
The mounting surface to which the control box is attached should have a surface evenness of better than ±

0.5 mm.

Bottom with cable grooves

The bottom of CBD6S (SMPS) is equipped with two cable grooves improving the cable management when
mounting. The grooves can be used to bypass the CBD for both motorcables and the mains cable (EU version
only) from one side to the other, giving a cleaner design.

Remember to lead the cables through the grooves before mounting the control box.

For mounting and operation of the desk panel, please see the separate user manual for desk panels.

Page 16 of 24

Electrical connection of the DL2 with control box

The systems is to be connected as shown on figure 3. Each DL2 is to be connected to the sockets on the
control box by means of the motor cables, which have a 6-pin plug in each end.

Finally the mains cable is to be mounted and power switched on. Please note that the control box
must only be connected to the voltage stated on the label.

DL

Hook for cable relief

DL

DP

Mains cable

Figure 3

Page 17 of 24

Initialisation of the DL2 with control box

Press the down button and the legs/actuators run down to the “end-stop position”.

Approx. 3 mm

Page 18 of 24

Disposal of LINAK’s products

As LINAK’s customers often ask us how our products can be disposed of or scrapped we have prepared this
guidance that enables a classification to different waste fractions for recycling or combustion.

Guidance

We recommend that our products be disassembled as much as possible and divided into different waste
groups for recycling or combustion.
For example, waste can be sorted into metals, plastics, cable scrap, combustible material, and recoverable
resources.

Some of these main groups can be further divided into subgroups; e.g. metal can be divided into steel/
aluminium/copper and plastic can be divided into ABS/PA/PE/PP.

As an example, the table below breaks down the different components in LINAK products to various recycling
groups:

Product

Components

Recycling group

Columns/ Actuator :

Spindle and motor
Plastic housing
Cable
PCB boards

Scrap
Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap

Control Box :

PCB boards
Plastic housing
Cable
Transformer

Electronics scrap
Plastic recycling or combustion
Cable scrap or combustion
Metal scrap

Handset/Control :

Plastic housing
Cable
PCB board

Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap

By now almost all our casted plastic parts are supplied with an interior code for plastic type and fibre
contents, if any.

Main groups of disposal

Product main groups

Metal scrap

Cable scrap

Electronics scrap

Plastic recycling

or combustin

Comments
DL2

X X X X

CBD6S (SMPS)

X X X X

DPXX

X X X

Disposal of batteries

Details regarding safe disposal of used and leaking batteries:
Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK
recommends that used or leaking batteries are disposed through local recycling system. Please do not throw
used or leaking batteries in normal household waste or in nature. This will cause damage to the enviroment.

How to deal with leaking batteries.

Leaking batteries should be disposed as described above.
If leaking batteries are discovered in the product the batteries must be removed at once to minimise damage
to the product. If leaking batteries are left in the product it might become defect.

It is recommended to use plastic gloves when handeling leaking batteries. The contents of a leaking batteries
can cause chemical burns and respiratory irritation.

If exposed to the contents of a leaking battery, please wash with soap and water. If irritation persists, please
seek medical attention. In case of eye contact, please flush eyes thoroughly with water for 15 minutes and
seek medical attention."

Page 19 of 24

Labels

Label for DL2

Label for CBD6S 200W (SMPS)

Label for CBD6S 300W (SMPS)

up to 4 channels

LINAK APPLICATION POLICY

The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK
product defined as hardware, software, technical advice, etc. related to an existing or a new customer
application.

LINAK products as defined above are applicable for a wide range of applications within the Medical,
Furniture, Desk and Industry areas. Yet, LINAK cannot know all the conditions under which LINAK products
will be installed, used, and operated, as each individual application is unique.

The suitability and functionality of the LINAK product and its performance under varying conditions
(application, vibration, load, humidity, temperature, frequency, etc.) can only be verified by testing, and shall
ultimately be the responsibility of the LINAK customer using any LINAK product.

LINAK shall be responsible solely that LINAK products comply with the specifications set out by LINAK and it
shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for
the application in question.

Page 20 of 24

DRAWING APPENDIX

DL2 Lifting Column

a

mm top plate

lmmtoppl te

77

1

'

Dl2 with built-in CBD6S

Modular jack connector

fix

LINAK A/5

DL1001C

3 mm bottom plate

.5 for DG 80x35 screws

'

Page 21 of 24

-

m

CBD6S 200W (SMPS)

r

0

;

--.

I

11 I

•

._-111}

I"

12

------t---•.

co

l

\

l

86.5

-

exagonal (M6 nut)

Page 22 of 24

CmD

It

a

- t41 \

-------:

I

12

86.5

R

CBD6S 300w (SMPS) up to 4 channels

n

l

rtm=J

w

- --

+

-$------

--------

u.

I

265

N

-o

1

-

Hexagonal (M6 nut)

Page 23 of 24

DECLARATION OF CONFORMITY

LINAK A/S

Smedevasnget 8

DK - 6430 Nordborg

hereby declares that LINAK Actuator System composed of:

Control 8ox(s) C8D6S

And
Linear Actuator(s) 31xxxH-xxxxx50S , 084, 085 , 086 , 087, 089 , 0812 , 0814 , 0816 , LA23 and I or
Lifting Column(s) DL 1A, DL2, DL4, DL5, DL6, DL7, DL8, DL9, DL 10, DL 11, DL 12, DL14, DL 15, DL16, DL17, 8ASE1

And
Desk Panel(s)
Handset(s)

DP1C, DP1K , DP1L, DP1V, DP1U, DPA , DP8 , DPF, DPH, OPT, WDPL 1
RFTOOO , RFRLOOx , H81xRF3000 , H82xRFxOOO

and / or

complies with EMC Directive: 2004/ 108/ EC according to following standards:
EN 61000-6-1:2007 , EN 61000-6-3:2007 , EN 55014-1 :2007+A1+A2, EN 55022:2011 Class 8,

complies with Low Voltage Directive 2006/95/ EC according to the standard:
EN 60335-1 :2012

complies with Machinery Directive 2006/42/ EC according to the standard:
EN 13849-1:2008 SRP/ CS Cat. 8 , PL =band SRESW PL = b

complies with RoHS2 Directive 2011/65/ EU according to the standard:
EN 55581:2012

and
RF Controls: RF-transmitter: H81xRF3000 RF-

transmitter: H82xRFxOOO RF­receiver: RFTOOO , RFRL

and/or
and/or

complies with the Radio equipment and Telecommunications terminal equipment Directive 1999/ 5/ EC:
EN 300220-2:2007 , EN 61000-6-1:2007 , EN 61000-6-3:2007 ,
EN 60335-1:2012 , EN 62311:2008

Nordberg , 2014-04-09

LINAK A/5

John Kling, 8.Sc.E.E.
Certification and Regulatory Affairs
Authorized to compile the relevant technical documentation

Original Declaration

Page 24 of 24

Copyrigh

t

©

LINAK

2014.0

6 MA-M9-02-518-B

LINAK

A/S

r

eserve

the

right

to

make

technica

l

alterations

FACTORIES

CHINA

LINAK (Shenzhen) Actuator Systems, Ltd.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.cn

DENMARK

LINAK A/S - Group Headquarters, Guderup
Phone: [phone]
Fax: [phone]
Fax: [phone] (Sales)
E-mail: [email protected]
www.linak.com

SLOVAKIA

LINAK Slovakia s.r.o.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.com

USA

LINAK U.S. Inc.
North and South American Headquarters
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak-us.com

SUBSIDIARIES

AUSTRALIA

LINAK Australia Pty. Ltd
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.com.au

AUSTRIA

LINAK Repräsentanz Österreich (Wien)
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.at

BELGIUM & LUXEMBOURG

LINAK Actuator-Systems NV/SA
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.be

BRAZIL

DENMARK

LINAK Danmark A/S
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.dk

FINLAND

LINAK OY
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.fi

FRANCE

LINAK France E.U.R.L
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.fr

GERMANY

ITALY

LINAK Italia S.r.l.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.it

JAPAN

LINAK K.K.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.jp

MALAYSIA

LINAK Actuators Sdn. Bhd.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.my

NETHERLANDS

NORWAY

LINAK Norge AS
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.no

POLAND

LINAK Polska
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.pl

REPUBLIC OF KOREA

LINAK Korea Ltd.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.kr

RUSSIAN FEDERATION

SWITZERLAND

LINAK AG
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.ch

TAIWAN

LINAK A/S Taiwan Representative Office
Phone: [phone]
Fax: [phone]
Mobile: [phone]
E-mail: [email protected]
www.linak.com.tw

TURKEY

LINAK İth. İhr. San. ve Tic. A.Ş.
Phone: + 90 312 4726338
Fax: + 90 312 4726635
E-mail: [email protected]
www.linak.com.tr

LINAK Do Brasil Comércio De Atuadores Ltda. LINAK GmbH

LINAK Actuator-Systems B.V.

000 LINAK

UNITED KINGDOM

Phone: [phone] – 7070
Fax: [phone] – 7060
E-mail: [email protected]
www.linak.com.br

CANADA

LINAK Canada Inc.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak-us.com

CZECH REPUBLIC

LINAK C&S S.R.O.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.de

INDIA

LINAK A/S India Liaison Office
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.in

IRELAND

LINAK UK Limited - Ireland
Phone: [phone]
Fax: [phone]

[phone] (UK Mobile)

Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.nl

NEW ZEALAND

LINAK New Zealand Ltd.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.co.nz

Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.ru

SPAIN

LINAK Actuadores, S.L.u
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.es

SWEDEN

LINAK Scandinavia AB
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

LINAK UK Limited
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.linak.co.uk

www.linak.cz

[phone] (Republic Of Ireland Mobile)
E-mail: [email protected]
www.linak.co.uk

www.linak.se

DISTRIBUTORS

ARGENTINA

Novotec Argentina SRL
Phone: +[54] (11) 4303-8900

+[54] (11) 4303-8989
Fax: +[54] (11) 4032-0184
E-mail: [email protected]
www.novotecargentina.com

AUSTRALIA

Ballarat Industrial Supplies
www.ballind.com.au

BL Shipways & Co
www.blshipway.com.au

Gas Strut Marine and Industrial
www.gasstrutmarine.com.au

Prime Motion & Control
www.primehyd.com.au

West Vic Industrial Supplies
www.westvicindustrial.com.au

COLOMBIA

MEM Ltda
Phone: +[57] (1) 334-7666
Fax: +[57] (1) 282-1684

IRAN

Bod Inc.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.bod.ir

PERU

Percy Martin Del Aguila Ubillus
Phone: [phone]

RUSSIAN FEDERATION

000 FAM
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.fam-drive.ru

SINGAPORE

Servo Dynamics Pte. Ltd.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.servo.com.sg

SOUTH AFRICA

Industrial Specialised Applications CC

For contact details on other countries please
visit www.linak.com or contact:

LINAK INTERNATIONAL

Phone: [phone]
Fax: [phone]
Fax: [phone] (Sales)
E-mail: [email protected]
www.linak.com

Terms of use

The user is responsible for determining the suitability of LINAK
products for specific application. LINAK takes great care in providing
accurate and up-to-date information on its products.
However, due to continuous development in order to improve its
products, LINAK products are subject to frequent modifications and
changes without prior notice. Therefore, LINAK cannot guarantee the
correct and actual status of sai d information on its products.
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the
same reasons as mentioned above, guarantee the availability of any
particular product. Therefore, LINAK reserves the right to discontinue

the sale of any product displayed on its website or listed in its

E-mail: [email protected]

Phone: [phone] or [phone] (Switch Board)

catalogues or other written material drawn up by LINAK.

www.memltda.com.co

INDONESIA

Pt. Himalaya Everest Jaya
Phone: [phone],

[phone]
Fax: [phone],

[phone]
E-mail: [email protected]
www.hej.co.id

Fax: [phone]
E-mail: [email protected]
www.isaza.co.za

UNITED ARAB EMIRATES

Mechatronics
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.mechatronics.ae

All sales are subject to the Standard Terms of Sale and Delivery for
LINAK. For a copy hereof, please contact LINAK.