Page 1
Page 1 of 32
LINAK.COM/DESKLINE
DL8, DL9, DL10 and DL11 system
User manual
Page 2
Page 2 of 32
Contents
Preface............................................................................................................................................. 3
Important information .................................................................................................................. 4
Safety instructions ......................................................................................................................... 4
Before installation, re-installation or troubleshooting ................................................................... 5
Before start-up ........................................................................................................................... 5
During operation ......................................................................................................................... 5
Misc. .......................................................................................................................................... 5
Only for EU markets ....................................................................................................................... 6
Only for Non EU markets .............................................................................................................. 6
Misuse ............................................................................................................................................. 6
Repairs ............................................................................................................................................. 7
Manufacturer’s declaration........................................................................................................... 7
Misc. on the DESKLINE
®
DL8/DL9/DL10/DL11 system ................................................................ 8
Warranty..................................................................................................................................... 8
Maintenance............................................................................................................................... 8
Description of the DESKLINE
®
system ......................................................................................... 9
Mounting guidelines for the DL8/DL9/DL10/DL11 (motor housing) .............................................. 10
Mounting guidelines for the DL8/DL9 (foot part) ......................................................................... 11
Mounting guidelines for the DL10/DL11 (foot part) ..................................................................... 11
Mounting for the desk (misc.) ..................................................................................................... 12
Mounting guidelines CBD4/CBD5/CBD6 ..................................................................................... 14
Electrical connection of the DL8/DL9/DL10/DL11 system ........................................................ 15
Initialisation of the DESKLINE DL8/DL9/DL10/DL11 parallel system ...................................... 16
Anti-Collision
TM
.............................................................................................................................. 17
DL11 with PIEZO
TM
: description of the feature .......................................................................... 18
Disposal of LINAK’s products ..................................................................................................... 19
Labels ............................................................................................................................................ 20
Drawing appendix ......................................................................................................................... 21
Declaration of conformity ............................................................................................................ 29
Addresses ....................................................................................................................................... 32
Page 3
Page 3 of 32
Preface
Dear User,
We are delighted that you have chosen a product from LINAK®.
LINAK systems are high-tech products based on many years of experience in the manufacture and development
of actuators, electric control boxes, controls and chargers.
This User Manual does not address the end-user. It is intended as a source of information for the manufacturer
of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics. It
is the responsibility of the manufacturer of the end-use product to provide a User Manual where relevant safety
information from this manual is passed on to the end-user.
We are sure that your LINAK product/system will give you many years of problem-free operation.
Before our products leave the factory they undergo full function and quality testing. Should you nevertheless
experience problems with your LINAK product/system, you are always welcome to contact your local dealer.
LINAK subsidiaries and some distributors situated all over the world have authorised service centres, which are
always ready to help you.
LINAK provides a warranty on all its products. This warranty, however, is subject to correct use in accordance
with the specifications, maintenance being done correctly and any repairs being carried out at a service centre,
which is authorised to repair LINAK products.
Changes in installation and use of LINAK products/systems can affect their operation and durability. The
products are not to be opened by unauthorised personnel.
The User Manual has been written based on our present technical knowledge. We are constantly working on
updating the information and we therefore reserve the right to carry out technical modifications.
LINAK A/S
Page 4
Page 4 of 32
Safety instruction
General
Important information
Important information on LINAK
®
products can be found under the following
headings:
Warning!
Failure to comply with these instructions may result in accidents involving
serious personal injury.
Failing to follow these instructions can result in the product being damaged
or being destroyed.
Safe use of the system is possible only when the operating instructions are read
completely and the instructions contained are strictly observed.
Failure to comply with instructions marked with the ”NOTE” symbol may result in
serious damage to the system or one of its components.
It is important for everyone who is to connect, install, or use the systems to
have the necessary information and access to this User Manual. Follow the
instructions for mounting – risk of injury if these instructions are not followed.
The appliance is not intended for use by young children or infirm persons
without supervision.
If there is visible damage on the product it must not be installed.
Note that during construction of applications, in which the actuator is to
be fitted, there must be no possibility of personal injury, for example the
squeezing of fingers or arms.
Assure free space for movement of application in both directions to avoid
blockade.
Page 5
Page 5 of 32
Before installation, re-installation, or troubleshooting
• Stop the DL8/DL9/DL10/DL11
• Switch off the power supply and pull out the mains plug.
• Relieve the DL8/DL9/DL10/DL11 of any loads, which may be released during
the work.
Before start-up:
• Make sure that the system has been installed as instructed in this User Manual.
• Make sure that the voltage of the control box is correct before the system is
connected to the mains.
• System connection. The individual parts must be connected before the control box
is connected to the mains. See the User Manual for LINAK actuators, if necessary.
During operation:
• If the control box makes unusual noises or smells, switch off the mains voltage
immediately.
• Ensure that the cables are not damaged.
• Unplug the mains cable on mobile equipment before it is moved.
Misc.
The actuator system has a sound level below 55dB(A) in typical applications.
Updated manuals and declarations can always be found here:
www.linak.com/deskline
Page 6
Page 6 of 32
Only for EU markets
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
Only for Non EU markets
Persons who do not have the necessary experience or knowledge of the
product/products must not use the product/products. Besides, persons with
reduced physical, sensory or mental abilities must not use the product/
products, unless they are under surveillance or they have been thoroughly
instructed in the use of the apparatus by a person who is responsible for the
safety of these persons.
Moreover, children must be under surveillance to ensure that they do not play
with the product.
It is the operator’s responsibility to ensure that there is free space for the
application to move without risk for the operator or bystanders before
operating the application.
Misuse
Do not overload the actuators – this can cause danger of personal injury and
damage to the system.
Do not use the actuator system for lifting persons. Do not sit or stand on a
table while operating – risk of personal injury.
Do not use the system in environments other than the intended indoor use.
Page 7
Page 7 of 32
Repairs
In order to avoid the risk of malfunction, all DESKLINE® repairs must only be carried out by authorised LINAK workshops or
repairers, as special tools must be used and special gaskets must be fitted. Lifting units under warranty must also be returned
to authorised LINAK workshops.
Warning!
If any of the DESKLINE
®
products are opened, there will be a risk of subsequent malfunction.
Warning!
The DESKLINE
®
systems do not withstand cutting oil.
Page 8
Page 8 of 32
Misc. on the DESKLINE® DL8/DL9/DL10/DL11 system
Warranty - 60 months on DESKLINE® (NEW)
This will be valid for all DESKLINE® products produced after the 1st of May 2015.
Products produced before 1
st
of May 2015 will still be covered by 36 months.
Products used in DESKLINE application: If these products are used in another application, they will be covered by 18 months
warranty.
If there is any doubt that returned products are within the warranty period it is to be treated as if they are covered by the
warranty. We recommend that you use the date of the Control box or actuator as reference if possible. We will have our
purchase no. printed on the label.
Maintenance
Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for damage and breaks.
Inspect the connections, cables, and plugs and check for correct functioning as well as fixing points.
Service of double-insulated products:
Class II
A Class II or double insulated electrical appliance is one which has been designed in such a way that it does not require a
safety connection to electrical earth (US: ground).
The basic requirement is that no single failure can result in dangerous voltage becoming exposed so that it might cause an
electric shock and that this is achieved without relying on an earthed metal casing. This is usually achieved at least in part by
having two layers of insulating material surrounding live parts or by using reinforced insulation.
There is no earthing/grounding means provided on the product, and no earthing/grounding means is to be added to the
product.
In Europe, a double insulated appliance must be labelled “Class II”, “double insulated” or bear the double insulation symbol (a
square inside another square).
Servicing a double-insulated product requires extreme care and knowledge of the system, and is to be done only by qualified
service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace.
The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).
Page 9
Page 9 of 32
Description of the DESKLINE® system
Each DESKLINE® actuator/column is equipped with a motor and parallel/memory drive is ensured by means of software in the
CBD4/CBD5/CBD6 that also takes account of an uneven load on the desk. Soft start and stop are also part of this software,
which ensures a soft start and stop when adjusting the desk.
Application of the DESKLINE® system:
Irrespective of the load the duty cycle 10% ~ 6 min./ hour or max. 2 min. at continuous use stated in the data sheets,
must NOT be exceeded as this will result in an overheating of the motor and control box. Exceeding the duty cycle will result in
a dramatic reduction of the life of the system.
The system range contains the following products:
• 1 control box CBD4/CBD5/CBD6
• DL8, DL9, DL10 or DL11 (1 - 3 (4))
• 1 exchangeable mains cable
• motor cables (1 - 3 (4))
• 1 DP1U/DPF1M (if memory function is required) DP1C/WDPL/DPT/DPF1C (if memory function and display is required) or 1
DPA/DPB/DP1K/DP1V/DPFK/DPF1K (if only up/down is required) or DPF1D (if display is required).
Page 10
Page 10 of 32
Mounting guidelines for the DL8/DL9/DL10/DL11 system
Mounting guidelines for DL8/DL9/DL10/DL11 (motor housing)
The motor housing is supplied with 6 M6 threaded holes meant for mounting onto the desk frame. We advise you to fasten the
desk frame by means of 6 pcs. M6 screws of a good quality (min. 8.8) and a suitable length, which must not go further into
the motor housing than max.10 mm. The thrust moment must not exceed 7.5 Nm.
It is recommended to use all six M6 threaded holes to mount the desk frame. The values of the bending moments of
the lifting units are only valid if the desk frame is mounted in this way. Tests with fixing the motor housing only by
means of the 4 threaded holes have proved that this is not enough to obtain a sufficient torsional stability of the desk.
The column may not be twisted. If the column is twisting / rotated it may cause a failure. The maximum moment that
the column can adapt in the rotation direction is 200 Nm.
Use all 6 threaded mounting holes M6 for screws.
Thrust moment is 7.5Nm
DL motor housing: be aware of the screw length.
Page 11
Page 11 of 32
Mounting guidelines for the DL8 and DL9 (foot part)
The DL8/DL9 is supplied with 4 M6 threaded holes for the mounting of the foot.
We advise you to fasten the foot by means of 4 pcs. M6 screws of a good quality (min. 8.8) and of a suitable length, which
must not go further into the DL8/DL9 column than 20 mm.
The thrust moment must not exceed 10 Nm in the bottom plate thread. The 4 holes in the bottom of the DL8/DL9 are placed
on a Ø 42 mm diameter circle.
Mounting guidelines for the DL10 (foot part)
The DL10 is supplied with 4 M6 threaded holes for the mounting of the foot.
We advise you to fasten the foot by means of 4 pcs. M6 screws of a good quality (min. 8.8) and of a suitable length, which
must not go further into the DL10 column than 20 mm.
The thrust moment must not exceed 10 Nm in the bottom plate thread. The 4 holes in the bottom of the DL10 are placed on a
Ø 46 mm diameter circle.
The holes in the foot must be sufficiently
larger than Ø 6 so that it is possible to
bring the foot to a level line at assembly/
mounting.
Page 12
Page 12 of 32
Mounting guidelines for the DL11 (foot part)
The DL11 is supplied with 4 M6 and 2 M8 threaded holes for mounting of the foot. We advise you to fasten the foot by means
of 4 pcs. M6 screws or 2 pcs M8 screws of a good quality (min. 8.8) and of a suitable length. The holes in the foot ought to be
sufficiently larger than ø6 so that it is possible to bring the foot to a level line at assembly/mounting.
The 4 M6 holes in the bottom of the column are placed on an Ø46mm pitch circle. The 2 M8 holes have their center 25 mm
from the center of the column.
96.5
177.1
32.53
50
32.53
46
35.4
Bottomplate
2XM8
4XM6
Foot
Mounting of the foot part of standard DL11
M6 screws must not go further than 20mm into the DL11 column. M8 screws must go min. 9 mm and not further than 11 mm
into the column. The thrust moment must not exceed 10Nm in the bottom plate thread.
Mounting of the foot part of standard DL11 with PIEZO™
M6 screws must not go further than 16mm into the DL11 column. M8 screws must go min. 9 mm and not further than 11 mm
into the column. The thrust moment must not exceed 10Nm in the bottom plate thread.
Page 13
Page 13 of 32
Mounting of the desk (misc.)
As the desktop amplifies the sound, we advise you to place a vibration/ shock absorbing material between the
desktop and the desk frame.
With a desktop thickness of 25 mm, it is necessary for the lowest edge of the lifting unit to be mounted max. 15 mm above
floor level to obtain a desk height of only 600 mm in the lowest position. If e.g. 2 mm vibration absorbing material is placed
between the desktop and the desk frame the lifting unit must be mounted max.
13 mm above floor level.
Page 14
Page 14 of 32
LINAK recommends that the DESKLINE® DL8/DL9/DL10/DL11 system should only be used in push applications with
the motor housing uppermost.
Placement of a monitor directly above the motor may cause malfunction of the monitor. Magnets inside the motor
may interrupt the picture on the monitor depending on the distance and type of monitor.
If this is the case the problem may be solved by placing an iron plate/tube or another magnetic material, somewhat
larger than the profile between the motor and the tabletop.
The mounting screws on the DP, DPA or DPB must be fastened with a max. torque of 1 Nm.
Example of how to mount a 2 parallel DESKLINE
®
DL8/DL9/DL10/DL11 system
Placement of a monitor directly above the motor housing may cause malfunction of the monitor. Magnets inside the motor
may interrupt the picture on the monitor depending on the distance and type of monitor. If this is the case, the problem may
be solved by placing an iron plate/tube or another magnetic material, somewhat larger than the motor housing, between the
motor and the desktop.
Page 15
Page 15 of 32
The CBD must not be packed in heat insulating material, but must be placed so that it can emit waste heat into the
surroundings. There are no ventilation holes to consider, the CBD emits heat through the surface.
The plug must be visible when the CBD is mounted so that the supply to the CBD can be disconnected at replacement, if any.
The mounting screws on the control box must be fastened with a max. torque of 1 Nm.
The mounting surface to which the control box is attached should have a surface evenness of better than ± 0.5 mm.
CBD6 - bottom with cable grooves
The bottom of CBD6 is equipped with two cable grooves improving the cable management when mounting. The grooves can
be used to bypass the CBD for both motorcables and the mains cable (EU version only) from one side to the other, giving a
cleaner design.
Remember to lead the cables through the grooves before mounting the control box.
For mounting and operation of the desk panel, please see the separate user manual for desk panels.
Mounting guidelines CBD4/CBD5/CBD6
The control box is to be fastened with 4 screws (3 screws for CBD5 and CBD6) with a head diameter between ø 8 and ø
10 mm. Out of regard for the tension surface ø 10 mm is preferable due to lower surface tension. See drawing appendix for
placing of mounting holes and the space the CBD takes up.
CBD4 - Control box
CBD5 - Control box
CBD6 - Control box
Page 16
Page 16 of 32
Mains cable
DP
DL8/DL9/
DL10/DL11
Figure 7
Electrical connection of the DL8/DL9/DL10/DL11 system
The systems is to be connected as shown on figure 7. Each DL8/DL9/DL10/DL11 is to be connected to the sockets on the
control box by means of the motor cables, which have a 6-pin plug in each end.
Finally the mains cable is to be mounted and power switched on. Please note that the control box must only be
connected to the voltage stated on the label.
CBD4/CBD5/CBD6 with earth
The CBD4/CBD5/CBD6 earth cable to be mounted on the desk construction (typically the top frame)in a way that ensures good
electrical contact. The function of the earth cable is to earth the desk and ground static electricity. The earth connection does
not protect other electrical products.
CBD4/CBD5 with mains cut-off (non ZERO models)
If the power cable is damaged it has to be replaced by an authorized LINAK service centre to avoid any danger.
Page 17
Page 17 of 32
Initialisation of the DESKLINE DL8/DL9/DL10/DL11 parallel system
Press the down button and the legs/actuators run down to the “buffer” causing cut-off due to excess current. Hereafter
they run approx. 3 mm (from software version 1.66, previosely 5 mm) upwards and thereby free of the “buffer”. When the
movement stops, the system is initialised. During the entire initialisation procedure, the down button must be pressed down.
If the button is released before the sequence is completed then the initialisation is interruppted and must be started
again from the beginning.
It is sometimes necessary to press the down button twice to start the initialisation. This is because the system can be in
different modes when the initialisation starts. There will be a 1.25 sec. delay. If an error situation occurs at the end stop
positions or the DL8/DL9/DL10/DL11 are changed to another stroke length, then the CBD4/CBD5/CBD6 has to be initialised
again.
The first two times the system runs into the outward end stop, it will automatically run approx. 3 mm back in inward direction.
The CBD5 and CBD6 can control the DL8/DL9/DL10/DL11 in 2 parallel while the CBD4 can control in 2, 3, and 4 parallel so
that the desk is always kept horizontal.
Approx. 5
mm
Page 18
Page 18 of 32
Anti-Collision™
The function anti-collision is a new option for the standard CBD4/CBD5/CBD6 advanced control box. A system with anticollision can limit material damages to a desk if a collision with a solid object should occur.
Anti-collision is working for DL9. The other DL types require a configuration of the control box.
Enabling the anti-collision
To enable the anti-collision function a little plug called a dongle must be mounted in one of the 2 control ports. The function is
only active when the dongle is mounted. – If you remove the dongle again you disable the function.
Method of operation
When the DL’s are running the CBD4/CBD5/CBD6 monitors the current consumption on each channel use a special algorithm.
If the current consumption on one channel is increased more than a predefined value a collision is assumed and all channels
are stopped immediately and all DL’s will start to run in the opposite direction (approx. 50 mm). This return drive is done
automatically and continues with or without any control button pressed (for max. 2.5 sec.).
The anti-collision sensitivity is different in up and downward direction. Upwards the force is approx. 20 kg. Downwards the
load will be approx. 40 kg + the load on the DL (the desk + what is on top of the desk). The 40 kg are needed to activate the
anti-collision function.
Situations where the anti-collision does not work
There are situations where the anti-collision will not be activated. These situations are:
• If the collision happens during the initialisation phase
• If the collision happens within the first 1000 m sec or after the control button has been released
• If the collision happens between the floor and the table and the load on the desk + the weight of the legs is lower than
40 kg.
• If the collision time span is too long time, e.g. if the collision is with a soft object
Page 19
Page 19 of 32
DL9 and DL11 with PIEZO™: description of the feature
For optimised safety against squeezing and blocking on a desk, LINAK has developed a DL11 columns with integrated sensor,
called PIEZO. The new option minimises the risk for damages on a desk caused by squeezing or blocking of obstacles in up and
down direction. Examples could be driving down into an office chair or into a container or up into a windowsill. To a certain
extent, the system also increases the personal safety, but it does not comply with legislation describing personal safety.
PIEZO allows the DL11 columns to have the standard built-in dimension and the standard stroke length. There are no visible
changes to the column.
Do not use the DL11 with PIEZO in combination with a crossbar or a foot construction where you place the column in a
tube welded on the foot.
Examples where PIEZO avoids squeezing situations.
Page 20
Page 20 of 32
Disposal of LINAK’s products
As LINAK’s customers often ask us how our products can be disposed of or scrapped we have prepared this guidance that
enables a classifi cation to different waste fractions for recycling or combustion.
Guidance
We recommend that our products be disassembled as much as possible and divided into different waste groups for recycling or
combustion.
For example, waste can be sorted into metals, plastics, cable scrap, combustible material, and recoverable resources.
Some of these main groups can be further divided into subgroups; e.g. metal can be divided into steel/aluminium/copper and
plastic can be divided into ABS/PA/PE/PP.
As an example, the table below breaks down the different components in LINAK products to various recycling groups:
Product Components Recycling group
Columns/ Actuator : Spindle and motor
Plastic housing
Cable
PCB boards
Scrap
Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap
Control Box : PCB boards
Plastic housing
Cable
Transformer
Electronics scrap
Plastic recycling or combustion
Cable scrap or combustion
Metal scrap
Handset/Control : Plastic housing
Cable
PCB board
Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap
By now almost all our casted plastic parts are supplied with an interior code for plastic type and fibre contents, if any.
Main groups of disposal
Product main groups Metal scrap Cable scrap Electronics scrap Plastic recycling
or combustin
Comments
DLX x x x x
CBD4/CBD5/CBD6 x x x x
DPXX x x x
WDPL x x x
Disposal of batteries
Details regarding safe disposal of used and leaking batteries:
Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK recommends that
used or leaking batteries are disposed through local recycling system. Please do not throw used or leaking batteries in normal
household waste or in nature. This will cause damage to the enviroment.
How to deal with leaking batteries.
Leaking batteries should be disposed as described above.
If leaking batteries are discovered in the product the batteries must be removed at once to minimise damage to the product. If
leaking batteries are left in the product it might become defect.
It is recommended to use plastic gloves when handeling leaking batteries. The contents of a leaking batteries can cause
chemical burns and respiratory irritation.
If exposed to the contents of a leaking battery, please wash with soap and water. If irritation persists, please seek medical
attention. In case of eye contact, please flush eyes thoroughly with water for 15 minutes and seek medical attention."
Page 21
Page 21 of 32
Labels
Label for CBD5
Label for CBD4
Labels for DL10 and DL11
Labels for DL8 and DL9
Page 22
Page 22 of 32
Label for CBD6
Page 23
Page 23 of 32
DL8
DRAWING APPENDIX
Page 24
Page 24 of 32
Standard DL9
1210
+8
-3
560
+5
-2
9
57
+1
0
63.5
70
+1
0
46
17
17.4
35.4
145
177
63
97
17
29.7
29.7
4xM6
4xM6
2xM6
Page 25
Page 25 of 32
Extended version DL9XL
1710
+8
-3
730
+5
-2
57
+1
0
63.5
70
+1
0
17.4
35.4
145
177
4xM6
11.5
17
46
2xM6
63
97
29.7
29.7
4xM6
17
Page 26
Page 26 of 32
DL10
1145
+5
-2
645 2
35.4
17.4145
177.1
4xM6
32.53
32.53
4xM6
97
17
46
70
+1
0
2xM6
63
17
Page 27
Page 27 of 32
1210
+8
-3
575
+5
-2
70
+1
0
17
17.4145
177
35.4
46
2xM6
97
63
17
4xM6
4xM6
32.53
32.53
2xM8
1210
+8
-3
560
+5
-2
70
+1
0
4xM6
17.4
17
145
177
46
63
97
2xM6
17
35.4
4xM6
32.53
32.53
2xM8
DL11
DL11 PIEZO
TM
Page 28
Page 28 of 32
1705
+8
-3
740
+5
-2
70
+1
0
4xM6
17
17.4
177
145
46
2xM6
97
63
17
35.4
4xM6
32.53
32.53
2xM8
DL11XL
CBD4
3
2
1
B
A
C
B
4
278
80
100.6
119
62
51
247
5.5
5.5
Page 29
Page 29 of 32
CBD6
CBD5
Page 30
Page 30 of 32
Page 31
Page 31 of 32
LINAK APPLICATION POLICY
The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as
hardware, software, technical advice, etc. related to an existing or new customer application.
LINAK products as defined above are applicable for a wide range of applications within the Medical, Furniture, Desk and
Industry areas. Yet, LINAK cannot know all the conditions under which LINAK products will be installed, used, and operated, as
each individual application is unique.
The suitability and functionality of the LINAK product and its performance under varying conditions (application, vibration,
load, humidity, temperature, frequency, etc.) can only be verified by testing, and shall ultimately be the responsibility of the
LINAK customer using any LINAK product.
LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it shall be the
responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question.
Page 32
Page 32 of 32
Copyright
©
LINAK 2018.01 MA-M9-02-333-L LINAK A/S reserve the right to make technical alterations
Terms of use
The user is responsible for determining the suitability of LINAK products for specific application. LINAK takes great care in providing accurate and
up-to-date information on its products.
However, due to continuous development in order to improve its products, LINAK products are subject to frequent modifications and changes
without prior notice. Therefore, LINAK cannot guarantee the correct and actual status of said information on its products.
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability of any
particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or
other written material drawn up by LINAK.
All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK.
FACTORIES
China
LINAK (Shenzhen) Actuator Systems, Ltd.
Tel: +86 755 8610 6656
Tel: +86 755 8610 6990
E-mail: [email protected]
www.linak.cn
Denmark - Headquarters
LINAK A/S - Group Headquarters
Tel: +45 73 15 15 15
Fax: +45 74 45 80 48
Fax (Sales): +45 73 15 16 13
E-mail: [email protected]
www.linak.com
USA
LINAK U.S. Inc.
North and South American Headquarters
User support: +1 800 392 7638
Tel: +1 502 253 5595
Fax: +1 502 253 5596
E-mail: [email protected]
www.linak-us.com
SUBSIDIARIES
Australia
LINAK Australia Pty. Ltd
Tel: +61 3 8796 9777
Fax: +61 3 8796 9778
E-mail: [email protected]
www.linak.com.au
Austria
LINAK Repräsentanz - Österreich (Wien)
Tel: +43 (1) 890 7446
Fax: +43 (1) 890 744615
E-mail: [email protected]
www.linak.at
Belgium
LINAK Actuator-Systems NV/SA
(Belgium & Luxembourg)
Tel: +32 (0)9 230 01 09
Fax: +32 (0)9 230 88 80
E-mail: [email protected]
www.linak.be - www.fr.linak.be
Brazil
LINAK DO BRASIL COMÉRCIO DE
ATUADORES LTDA.
Tel: +55 (11) 2832 – 7070
Fax: +55 (11) 2832 – 7060
E-mail: [email protected]
www.linak.com.br
C
anada
LINAK Canada Inc.
Tel: +1 502 253 5595
Fax: +1 416-255-7720
E-mail: [email protected]
www.linak-us.com
Czech Republic
Denmark - International
LINAK International
Tel: +45 73 15 15 15
Fax: +45 74 45 90 10
Fax (Sales): +45 73 15 16 13
E-mail: [email protected]
www.linak.com
Denmark - Sales
Finland
LINAK OY
Tel: +358 10 841 8700
E-mail: linak@linak.fi
www.linak.fi
France
LINAK FRANCE E.U.R.L
Tel: +33 (0) 2 41 36 34 34
Fax: +33 (0) 2 41 36 35 00
E-mail: [email protected]
www.linak.fr
Germany
India
LINAK A/S India Liaison Office
Tel: +91 120 4531797
Fax: +91 120 4786428
E-mail: [email protected]
www.linak.in
Italy
LINAK ITALIA S.r.l.
Tel: +39 02 48 46 33 66
Fax: +39 02 48 46 82 52
E-mail: [email protected]
www.linak.it
Japan
Malaysia
LINAK Actuators Sdn. Bhd.
Tel: +60 4 210 6500
Fax: +60 4 226 8901
E-mail: [email protected]
www.linak.my - www.linak.co.id
www.linak.pk - www.linak.ph
Netherlands
LINAK Actuator-Systems B.V.
Tel: +31 76 5 42 44 40
Fax: +31 76 5 42 61 10
E-mail: [email protected]
www.linak.nl
New Zealand
LINAK New Zealand Ltd
Tel: +64 9580 2071
Fax: +64 9580 2072
E-mail: [email protected]
www.linak.com.au
Norway
DISTRIBUTORS
Argentina
NOVOTEC ARGENTINA SRL
Tel: 011-4303-8989/8900
Fax: 011-4032-0184
E-mail: [email protected]
www.novotecargentina.com
Colombia
India
Mechatronics Control Equipments India Pvt Ltd
Tel: +91-44-28558484, 85
E-mail: [email protected]
www.mechatronicscontrol.com
Indonesia
PT. HIMALAYA EVEREST JAYA
Tel: +6 221 544 8956, +6 221 544 8965
Fax: +6 221 619 1925
Fax (Sales): +6 221 619 1925
E-mail: [email protected]
www.hej.co.id
Iran
Israel
Russia
Singapore
Servo Dynamics Pte Ltd
Tel: +65 6844 0288
Fax: +65 6844 0070
E-mail: [email protected]
www.servo.com.sg
South Africa
Industrial Specialised Applications CC
Tel: +27 011 466 0346
E-mail: [email protected]
www.isaza.co.za
United Arab Emirates
Poland
LINAK Polska
Tel: +48 22 295 09 70
E-mail: [email protected]
www.linak.pl
Republic of Korea
LINAK Korea Ltd.
Tel: +82-(0)2-6231-1515
Fax: +82-(0)2-6231-1516
E-mail: [email protected]
www.linak.kr
Russia
Spain
LINAK Actuadores, S.L.u
Tel: +34 93 588 27 77
Fax: +34 93 588 27 85
E-mail: [email protected]
www.linak.es
Sweden
LINAK Scandinavia AB
Tel: +46 8 732 20 00
Fax: +46 8 732 20 50
E-mail: [email protected]
www.linak.se
Switzerland
LINAK AG
Tel: +41 43 388 31 88
Fax: +41 43 388 31 87
E-mail: [email protected]
www.de.linak.ch - www.fr.linak.ch
www.it.linak.ch
Taiwan
LINAK (Shenzhen) Actuator systems Ltd.
Taiwan Representative office
Tel: +886 2 27290068
Fax: +886 2 27290096
E-mail: [email protected]
www.linak.tw
Turkey
LINAK İth. İhr. San. ve Tic. A.Ş.
Tel: + 90 312 4726338
Fax: + 90 312 4726635
E-mail: [email protected]
www.linak.com.tr
United Kingdom
LINAK UK Limited
Tel: +44 (0)121 544 2211
Fax: +44 (0)121 544 2552
E-mail: [email protected]
www.linak.co.uk
Loading...