Linak DL12, DB12, DL17 systemwith CBD4, CBD5, CBD6 User Manual

Page 1 of 36

USER MANUAL

DL12, DB12, DL14,
DB14, DL17 system
with CBD4, CBD5 or CBD6

To learn more about LINAK, please visit:

WWW.LINAK.COM

Page 2 of 36

Page 3 of 36

Contents

Preface ............................................................................................................................................... 4

Important information ....................................................................................................................... 5

Safety instructions .............................................................................................................................. 5

General .......................................................................................................................................... 5

Before installation, reinstallation or troubleshooting ........................................................................ 6

Before start-up ............................................................................................................................... 6

During operation ............................................................................................................................ 6

Misc. .............................................................................................................................................. 6

Only for EU markets........................................................................................................................ 7

Only for Non EU markets ................................................................................................................ 7

Misuse ............................................................................................................................................ 7

Repairs ............................................................................................................................................... 8

Manufacturer’s declaration ................................................................................................................ 8

Misc. on the DESKLINE

®

system ......................................................................................................... 9

Warranty ........................................................................................................................................ 9

Maintenance .................................................................................................................................. 9

Description of the DESKLINE

®

system ............................................................................................. 10

Mounting guidelines for the DL14 system ...................................................................................... 11

Mounting top .............................................................................................................................. 11

Mounting foot ............................................................................................................................. 13

Mounting guidelines for the column DL12 .................................................................................... 14

Mounting top .............................................................................................................................. 14

Mounting foot ............................................................................................................................. 14

Mounting guidelines for the column DL17 .................................................................................... 15

Mounting top .............................................................................................................................. 15

Mounting foot ............................................................................................................................. 15

Mounting guidelines for DB12 and DB14 ...................................................................................... 16

Mounting guidelines for the CBD4/CBD5/CBD6S ........................................................................... 18

Electrical connection of the DB/DL system ..................................................................................... 19

Initialisation of the DESKLINE parallel system ................................................................................ 20

Anti-Collision

TM

.................................................................................................................................. 21

PIEZO

TM

: description of the feature ................................................................................................ 22

Accessories and repair ...................................................................................................................... 23

Disposal of LINAK products .............................................................................................................. 24

Labels ............................................................................................................................................. 25

Drawing appendix ............................................................................................................................ 27

Declaration of conformity ................................................................................................................ 33

Addresses .......................................................................................................................................... 36

Page 4 of 36

Preface

We are delighted that you have chosen a product from LINAK A/S. LINAK systems are high-tech products
based on many years of experience in the manufacture and development of actuators, electric control boxes,
controls, and chargers.

We are also constantly improving our products to meet customer requirements.

This User Manual will tell you how to install, use and maintain your LINAK DESKLINE

®

products.

We are sure that the DESKLINE

®

products will give you many years of problem-free operation. Before our
products leave the factory they undergo full function and quality testing. Should you nevertheless experience
problems with your systems, you are always welcome to contact our service departments or service centres.

LINAK subsidiaries and distributors all over the world have authorised service centres, which are always ready
to help you.

LINAK provides a warranty on all its products. This warranty, however, is subject to correct use in accordance
with the specifications, maintenance being done correctly and any repairs being carried out at a service
centre, which is authorised to repair LINAK products.

Changes in installation and use of LINAK systems can affect their operation and durability. Changes must
therefore only be made by agreement with LINAK A/S and are made at your own risk.

LINAK A/S

Page 5 of 36

Safety instructions

General

Important information

Important information on LINAK

®

products can be found under the

following headings:

Warning!

Failure to comply with these instructions may result in accidents
involving serious personal injury.

Failing to follow these instructions can result in the product being
damaged or being destroyed.

Safe use of the system is possible only when the operating instructions
are read completely and the instructions contained are strictly observed.

Failure to comply with instructions marked with the ”NOTE” symbol may
result in serious damage to the system or one of its components.

It is important for everyone who is to connect, install or use the
systems to have the necessary information and access to this User
Manual. Follow the instructions for mounting – risk of injury if these
instructions are not followed.

The appliance is not intended for use by young children or infirm
persons without supervision.

If there is visible damage on the product, it must not be installed.

Note that during construction of applications, in which the actuator
is to be fitted, there must be no possibility of personal injury, for
example squeezing of fingers or arms.

Assure free space for movement of applications in both directions
to avoid blockade.

Page 6 of 36

Before installation, reinstallation, or troubleshooting

• Stop the DB/DL.

• Switch off the power supply and pull out the mains plug.

• Relieve the DB/DL of any loads, which may be released during the work.

Before start-up:

• Make sure that the system has been installed as instructed in this User
Manual.

• Make sure that the voltage at the control box is correct before the
system is connected to the mains.

• System connection. The individual parts must be connected before the
control box is connected to the mains. See the User Manual for LINAK
actuators, if necessary.

During operation:

• If the control box makes unusual noises or smells, switch off the mains
voltage immediately.

• Take care that the cables are not damaged.

• Unplug the mains cable on mobile equipment before it is moved.

Misc.

The actuator system has a sound level below 55dB(A) in typical
applications.

Updated manuals and declarations can always be found here:

www.linak.com/deskline

Page 7 of 36

Only for EU markets

This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have given
supervision or instruction concerning the use of the appliance in a
safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.

Only for Non EU markets

Persons who do not have the necessary experience or knowledge of
the product/products must not use the product/products. Besides,
persons with reduced physical, sensory or mental abilities must not
use the product/products, unless they are under surveillance or they
have been thoroughly instructed in the use of the apparatus by a
person who is responsible for the safety of these persons.

Moreover, children must be under surveillance to ensure that they
do not play with the product.

It is the operator’s responsibility to ensure that there is free space for
the application to move without risk for the operator or bystanders
before operating the application.

Misuse

Do not overload the actuators – this can cause danger of personal
injury and damage to the system.

Do not use the actuator system for lifting persons. Do not sit or
stand on a table while operating – risk of personal injury.

Do not use the system in environments other than the intended
indoor use

Page 8 of 36

Repairs

In order to avoid the risk of malfunction, all DESKLINE® repairs must only be carried out by authorised LINAK
workshops or repairers, as special tools must be used and special gaskets must be fitted. Lifting units under
warranty must also be returned to authorised LINAK workshops.

Warning!

If any of the DESKLINE

®

products are opened, there will be a risk of subsequent malfunction.

Warning!

The DESKLINE

®

systems do not withstand cutting oil.

Page 9 of 36

Misc. on the DESKLINE® system

Warranty

There is a 36 months’ warranty on DESKLINE products against manufacturing faults from the production date
of the individual products (see label).
LINAK A/S warranty is only valid in so far as the equipment has been used and maintained correctly and has
not been tampered with. Furthermore, the system must not be exposed to violent treatment. In the event of
this, the warranty will be ineffective/invalid. For further details, please see standard terms of sale and delivery
for LINAK A/S.

Maintenance

Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for damage and
breaks.
Inspect the connections, cables and plugs and check for correct functioning as well as fixing points.

Service of double insulated products:

Class II

A Class II or double insulated electrical appliance is one which has been designed in such a way that it does
not require a safety connection to electrical earth (US: ground).
The basic requirement is that no single failure can result in dangerous voltage becoming exposed so that it
might cause an electric shock and that this is achieved without relying on an earthed metal casing. This is
usually achieved at least in part by having two layers of insulating material surrounding live parts or by using
reinforced insulation.
There is no earthing/grounding means provided on the product, and no earthing/grounding means is to be
added to the product.
In Europe, a double insulated appliance must be labelled “Class II”, “double insulated” or bear the double
insulation symbol (a square inside another square).
Servicing a double-insulated product requires extreme care and knowledge of the system, and is to be done
only by qualified service personnel. Replacement parts for a double insulated product must be identical to the
parts they replace.

The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).

Page 10 of 36

Description of the DESKLINE® system

Each DESKLINE® actuator/column is equipped with a motor and parallel/memory drive is ensured by means of
software in the CBD4/CBD5/CBD6 that also takes account of an oblique load on the desk. Soft start and stop
are also part of this software, which ensures a soft start and stop when adjusting the desk.

Application of the DESKLINE

®

system:

Irrespective of the load, the duty cycle 10% ~ 6 min./ hour or max. 2 min. at continuous use stated in
the data sheets, must NOT be exceeded as this will result in a superheating of the motor and the control box.
Exceeding the duty cycle will result in a dramatic reduction of the life of the system.

The DB/DL system range contains following products:

• 1 control box CBD4/CBD5/CBD6

• DL12, DB12, DL14, DB14 or DL17 (1 - 4)

• 1 exchangeable mains cable

• motor cables (1 - 4)

• 1 DP1U/DPF1M (if memory function is required) DP1C//DPT/DPF1C (if memory function and display
are required) or 1 DPA/DPB/DP1K/DP1V/DPFK (if only up/down is required).

Page 11 of 36

Mounting guidelines for the DL14 system

Mounting top

The top of the column is supplied with 4 M6 threaded holes meant for mounting onto the desk frame. We
advise you to fasten the desk frame by means of 4 pcs. M6 screws of a good quality (min. 8.8) and of a
suitable length, which must not go further than max. 14 mm into the column. The thrust moment must not
exceed 10 Nm.

Screw length
Min. B + 9 mm
Max. B + 14 mm

Page 12 of 36

As the desktop amplifies the sound, we advise you to place a vibration/shock absorbing material
between the desktop and the desk frame.

Table top
Absorbing
material

Height of the DL in the lowest position

Min. desk height

Floor level

LINAK recommends that the DESKLINE® DL system should be used in push applications.

(Example of how to mount a 2-parallel DESKLINE

®

DL system)

Page 13 of 36

Mounted with 2 x M8

Mounted with 4 x M6

Mounting guidelines for the column DL14

Mounting foot

The DL14 is supplied with 4 M6 threaded holes and 2 M8 screws for mounting of the foot. You can either
use 2 M8 screws or 4 M6 screws dependent on your foot design. We advise you to use screws of a good
quality min. 8.8 and of a suitable length, which must not go further than 16 mm into the DL14 column.
The thrust moment must not exceed 10 Nm in the bottom plate thread. The holes in the foot ought to be
sufficiently larger than ø6 so that it is possible to bring the foot to a level line at assembly/mounting of the
table.

Page 14 of 36

Mounting guidelines for the column DL12

Min. 12 mm

MC6

Mounting foot

The DL12 is supplied with 4 x M6 threaded holes.
We advise you to use screws of a good quality min.

8.8 and of a suitable length. The length needs to be
minimum 9 mm.
The screw torque must not exceed 10 Nm in the
bottom plate thread.
The holes in the foot ought to be sufficiently larger
than ø6 so that it is possible to bring the foot to a
level line at assembly/mounting of the table.

Min. 9 mm

SECTION SKRUE_BUND-SKRUE_BUND

MC6

As the desktop amplifies the sound, we advise you to place a vibration/shock absorbing material
between the desktop and the desk frame.

(Example of how to mount the DESKLINE

®

system)

Mounting top

The top of the column is supplied with 4 x M6
threaded holes meant for mounting onto the desk
frame. We advise you to fasten the desk frame by
means of 4 x M6 screws of a good quality (min. 8.8)
and of a suitable length, minimum 12 mm. The screw
torque must not exceed 10 Nm.

Page 15 of 36

Mounting guidelines for the column DL17

Mounting foot

The DL17 is supplied with 4 x MG threaded holes and
2 x M8 screws for mounting of the foot. You can use
either 2 x M8 screws or 4 x MG screws dependent on
your foot design. We advise you to use screws of a
good quality min. 8.8 and of a suitable length, which
must not go into the DL7 column further than 16
mm. The screw torque must not exceed 10 Nm in the
bottom plate thread.
The holes in the foot ought to be sufficiently larger
than (1)6 so that it is possible to bring the foot to a
level line at assembly/mounting of the table.

Mounting top

The top of the column is supplied with 4 x MG
threaded holes meant for mounting onto the desk
frame . We advise you to fasten the desk frame by
means of 4 x MG screws of a good quality (min. 8.8)
and of a suitable length of minimum 10 mm and must
not go into the column further than maximum 14
mm. The screw torque must not exceed 10 Nm

Min. 10 mm

Max. 14 mm

MC 6

Top Plate

Min 10 mm

Max. 16 mm

Min. 10 mm

Max. 16 mm

Min. 10 mm

Max. 14 mm

MC 6

MC 8

Bottom Plate

MC 6

Top Plate

As the desktop amplifies the sound, we advise you to place a vibration/shock absorbing material
between the desktop and the desk frame.

(Example of how to mount the DESKLINE

®

system)

Page 16 of 36

Mounting guidelines for DB12 and DB14

For detailed information on how to mount the DB12 or the DB14, please contact LINAK A/S.

The top of the motor is supplied with holes for the self-tapping special screws.These screws together with the
2 rubber washers are supplied with the DB12/DB14.
On the top of the motor there is the special rubber suspension, which should always be used when the DB12/
DB14. is mounted in a column. The top flange where the motor is mounted must be 4 mm thick ±1 mm, and
the 2 mounting holes should be ø12 mm with a centre distance of 36 mm. The screw torque must be 2
Nm ±0.1 Nm.

Middle tube: For detailed information on how to mount the middle tube of your column, please
contact LINAK A/S

Bottom: At the bottom of the DB12 or the DB14 the inner spindle should be mounted by means
of a 22-teeth spline profile and a M5 screw in the bottom of the spindle.

Top:

Special screws

Rubber washer

Rubber suspension

Motor

Page 17 of 36

The DB12/DB14 gives the possibility of synchronous drive of the middle profile - to make sure that
the profiles are in the right place, you have to secure that both the hollow and the massive spindles
are driven in the bottom position. For detailed information on how to mount the DB12/DB14, please
contact LINAK A/S.

From the factory, the DB12/DB14 is delivered with the hollow spindle driven into end position. Please
observe that the solid spindle may roll out during transportation/handling, but it must be rolled back
to end position before mounting in the profile.

As the desktop amplifies the sound,we advise you to place a vibration/shock absorbing material
between the desktop and the desk frame

Do not drive the DB12/DB14 to the outer end position before mounting. This will result in damaging
the DB.

Example of how to mount the DESKLINE

®

system

Page 18 of 36

The CBD must not be packed in heat insulating material, but must be placed so that it can emit waste heat
into the surroundings. There are no ventilation holes to consider, the CBD emits heat through the surface.
The plug must be visible when the CBD is mounted so that the supply to the CBD can be disconnected at
replacement, if any.
The mounting screws on the control box must be fastened with a max. torque of 1 Nm.
The mounting surface to which the control box is attached should have a surface evenness of better than
±0.5 mm.

CBD5/CBD6 - bottom with cable grooves

The bottom of the CBD5/CBD6 is equipped with two cable grooves improving the cable management when
mounting. The grooves can be used to bypass the CBD for both motor cables and the mains cable (EU version
only) from one side to the other, giving a cleaner design.

Remember to lead the cables through the grooves before mounting the control box.

For mounting and operation of the desk panel, please see the separate user manual for desk panels.

Mounting guidelines CBD4/CBD5/CBD6

The control box is to be fastened with 4 screws (3 screws for the CBD5 and theCBD6) with a head diameter
between ø 8 and ø 10 mm. Out of regard for the surface tension ø 10 mm is preferable due to lower surface
tension. See drawing appendix for placing of mounting holes and the space the CBD takes up.

CBD4 - Control box

CBD5 - Control box

CBD6 - Control box

Page 19 of 36

Figure 7

DP/WDPL

Mains cable

DL/DB

Hook for cable relief

Electrical connection of the DB/DL system

The DB/DL system is to be connected as shown on figure 7. The DB/DL is to be connected to the sockets on
the control box by means of the motor cables, which have a 6-pin plug in each end.

Finally, the mains cable is to be mounted and power switched on. Please note that the control box
must only be connected to the voltage stated on the label.

CBD4/CBD5/CBD6 with earth

The CBD4/CBD5/CBD6 earth cable to be mounted on the desk construction (typically the top frame)in a way
that ensures good electrical contact. The function of the earth cable is to earth the desk and ground static
electricity. The earth connection does not protect other electrical products.

CBD4/CBD5 with mains cut-off (non ZERO models)

If the power cable is damaged it has to be replaced by an authorized LINAK service centre to avoid
any danger.

Page 20 of 36

Initialisation of the DESKLINE parallel system

The DESKLINE system is initialised by pressing the down button once or twice and holding it down until the
DB/DL runs into end stop. It will then automatically run approx. 5 mm out again and hereafter slowly run in
again. Only release the down button when the movement has stopped completely.

If the button is released before the sequence is completed, the initialisation is interuppted and must
be started again from the beginning.

The first two times the system runs into the outward end stop, it will automatically run approx. 3 mm back in
inward direction.

Approx. 5 mm

The CBD5 and the CBD6 can control the DL5 and the DL6 in 2 parallel while the CBD4 can control the DL5
and the DL6 in 2, 3, and 4-parallel so that the desk is always kept horizontal.

Page 21 of 36

Anti-Collision™

The function (anti-collision) is an option for the standard CBD4/CBD5/CBD6 advanced/control box software
0077432 version 1.66 and later. A system with anti-collision can limit material damages on a desk if a
collision with a solid object should occur.

Enabling the anti-collision

To enable the anti-collision function a little plug called a dongle must be mounted in one of the 2 control
ports. The function is only active when the dongle is mounted. – If you remove the dongle again, you disable
the function.

Method of operation

When the DLs/DBs are running the CBD4/CBD5/CBD6 monitors the current consumption on each channel
using a special algorithm. If the current consumption on one channel is increased by more than a predefined
slope, a collision is assumed and all channels are stopped immediately and all DLs/DBs will start to run in the
opposite direction (approx. 50 mm). This return drive is done automatically and continues with or without
any control key pressed (for max. 2.5 sec.).

The anti-collision sensitivity is different in upward and downward direction. Upwards the force is approx. 20
kg. Downwards the load will be approx. 40 kg + the load on the DL/DB (the desk + what is on top of the
desk). The 40 kg are needed to activate the anti-collision function.

Situations where the anti-collision does not work

There are situations where the anti-collision will not be activated. These situations are:

• If the collision happens during the initialisation phase

• If the collision happens within the first 1000 msec or after the control button has been released

• If the collision happens between the floor and the table and the load on the desk + the weight of the legs
are lower than 40 kg

• If the collision happens over too long time, e.g. if the collision is with a soft object.

Page 22 of 36

PIEZO™: description of the feature

For optimised safety against squeezing and blocking on a desk, LINAK has developed the DBs and columns
with an integrated sensor, called PIEZO. The option minimises the risk for damages on a desk caused by
squeezing or blocking of obstacles in up and down direction. Examples could be driving down into an office
chair or into a container or up into a windowsill. To a certain extent, the system also increases the personal
safety, but it does not comply with legislation describing personal safety.

PIEZO allows the DBs or columns to have the standard built-in dimension and the standard stroke length.
There are no visible changes to the column.

Examples where PIEZO avoids squeezing situations.

Page 23 of 36

Accessories and repair

Ordering accessories

Order from your nearest LINAK® dealer or subsidiary.

Accessories

Please contact your nearest LINAK dealer for information.

Repairs

Systems should only be repaired by an authorised LINAK service centre or an engineer. Systems to be
repaired under warranty must be sent to an authorised LINAK service centre.

Warning!

By unauthorised opening of the system there is a risk that it may malfunction at a later date.

Spare parts

Please contact your nearest LINAK dealer for information on spare parts.

Page 24 of 36

Disposal of LINAK products

As LINAK customers often ask us how our products can be disposed of or scrapped, we have prepared this
guidance that enables a classification to different waste fractions for recycling or combustion.

Guidance

We recommend that our products be disassembled as much as possible and divided into different waste groups
for recycling or combustion.
For example, waste can be sorted into metals, plastics, cable scrap, combustible materials and recoverable resources.

Some of these main groups can be further divided into subgroups; e.g. metal can be divided into steel/
aluminium/copper and plastic can be divided into ABS/PA/PE/PP.

As an example, the table below breaks down the different components in LINAK products to various recycling
groups:

Product Components Recycling group

Columns/ Actuator : Spindle and motor

Plastic housing
Cable
PC boards

Metal scrap
Plastic recycling or combustion
Cable scrap or combustion
Electronic scrap

Control Box : PC boards

Plastic housing
Cable
Transformer

Electronic scrap
Plastic recycling or combustion
Cable scrap or combustion
Metal scrap

Handset/Control : Plastic housing

Cable
PC boards

Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap

By now, almost all our casted plastic parts are supplied with an interior code for plastic types and fibre
contents, if any.

Main groups of disposal

Product main groups Metal scrap Cable scrap Electronics scrap Plastic recycling

or combustin

Comments

DL12

DB12 X X X X

DL14 X X X X

DB14 X X X X

DL17

CBD4/CBD5/CBD6 X X X X

DPXX X X X

Disposal of batteries

Details regarding safe disposal of used and leaking batteries:
Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK
recommends that used or leaking batteries are disposed through local recycling systems. Please do not throw
used or leaking batteries in normal household waste or in nature. This will cause damage to the enviroment.

How to deal with leaking batteries

Leaking batteries should be disposed as described above.
If leaking batteries are discovered in the product, the batteries must be removed at once to minimise damage
to the product. If leaking batteries are left in the product, it might become defective.
It is recommended to use plastic gloves when handling leaking batteries. The contents of leaking batteries
can cause chemical burns and respiratory irritation.
If exposed to the contents of a leaking battery, please wash with soap and water. If irritation persists, please
seek medical attention. In case of eye contact, please flush eyes thoroughly with water for 15 minutes and
seek medical attention."

Page 25 of 36

Label for DL14

Label for DB14 Label for DL17Label for DL12Label for DB12

Label for CBD6

Label for CBD5

Label for CBD4

Page 26 of 36

LINAK APPLICATION POLICY

The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK
product defined as hardware, software, technical advice, etc. related to an existing or a new customer
application.

LINAK products as defined above are applicable for a wide range of applications within the Medical,
Furniture, Desk and Industry areas. Yet, LINAK cannot know all the conditions under which LINAK products
will be installed, used, and operated, as each individual application is unique.

The suitability and functionality of the LINAK product and its performance under varying conditions
(application, vibration, load, humidity, temperature, frequency, etc.) can only be verified by testing, and shall
ultimately be the responsibility of the LINAK customer using any LINAK product.

LINAK shall be responsible solely that LINAK products comply with the specifications set out by LINAK and it
shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for
the application in question.

Page 27 of 36

DRAWING APPENDIX

DL12

60

+1

0

100

+1

0

89.6

49.6

545 3.5

518

3.5

94.8

54.8

1178
1205

Page 28 of 36

DL14

Page 29 of 36

DL17

57.2

63.6

70

+1

0

70

+1

0

518 3.5

57.2

63.6

1178

+6.5

-4.5

Page 30 of 36

DB12

DB14

Nominal lenght 500 3 mm

Minimum lenght retracted at max. load 496

3 mm

12

4

42

48

36

Page 31 of 36

CBD4

3

2

1

B

A

C

B

4

278

80

100.6

119

62

51

247

5.5

5.5

CBD5

Page 32 of 36

CBD6

Page 33 of 36

Page 34 of 36

Page 35 of 36

Page 36 of 36

Copyright

©

LINAK 2013.10 MA-M9-02-503 LINAK A/S reserve the right to make technical alterations

Terms of use

The user is responsible for determining the suitability of LINAK
products for specific application. LINAK takes great care in providing
accurate and up-to-date information on its products.
However, due to continuous development in order to improve its
products, LINAK products are subject to frequent modifications and
changes without prior notice. Therefore, LINAK cannot guarantee the
correct and actual status of said information on its products.
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the
same reasons as mentioned above, guarantee the availability of any
particular product. Therefore, LINAK reserves the right to discontinue
the sale of any product displayed on its website or listed in its
catalogues or other written material drawn up by LINAK.
All sales are subject to the Standard Terms of Sale and Delivery for
LINAK. For a copy hereof, please contact LINAK.

FACTORIES

CHINA

LINAK (Shenzhen) Actuator Systems, Ltd.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.cn

SUBSIDIARIES

AUSTRALIA

LINAK Australia Pty. Ltd
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.com.au

AUSTRIA

LINAK Repräsentanz Österreich (Wien)
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.at

BELGIUM & LUXEMBOURG

LINAK Actuator-Systems NV/SA
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.be

BRAZIL

LINAK Do Brasil Comércio De Atuadores Ltda.
Phone: [phone] – 7070
Fax: [phone] – 7060
E-mail: [email protected]

www.linak.com.br

CANADA

LINAK Canada Inc.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak-us.com

CZECH REPUBLIC

LINAK C&S S.R.O.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.cz

DISTRIBUTORS

ARGENTINA

Novotec Argentina SRL
Phone: +[54] (11) 4303-8900
+[54] (11) 4303-8989
Fax: +[54] (11) 4032-0184
E-mail: [email protected]

www.novotecargentina.com

AUSTRALIA

Ballarat Industrial Supplies

www.ballind.com.au

BL Shipways & Co

www.blshipway.com.au

Gas Strut Marine and Industrial
www.gasstrutmarine.com.au

Prime Motion & Control
www.primehyd.com.au

West Vic Industrial Supplies

www.westvicindustrial.com.au

COLOMBIA

MEM Ltda
Phone: +[57] (1) 334-7666
Fax: +[57] (1) 282-1684
E-mail: [email protected]
www.memltda.com.co

INDONESIA

Pt. Himalaya Everest Jaya
Phone: [phone],
[phone]
Fax: [phone],
[phone]
E-mail: [email protected]

www.hej.co.id

DENMARK

LINAK A/S - Group Headquarters, Guderup
Phone: [phone]
Fax: [phone]
Fax: [phone] (Sales)
E-mail: [email protected]

www.linak.com

SLOVAKIA

LINAK Slovakia s.r.o.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.com

USA

LINAK U.S. Inc.
North and South American Headquarters
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak-us.com

DENMARK

LINAK Danmark A/S
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.dk

FINLAND

LINAK OY
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.fi

FRANCE

LINAK France E.U.R.L
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.fr

GERMANY

LINAK GmbH
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.de

INDIA

LINAK A/S India Liaison Office
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.in

IRELAND

LINAK UK Limited - Ireland
Phone: [phone]
Fax: [phone]
[phone] (UK Mobile)
[phone] (Republic Of Ireland Mobile)
E-mail: [email protected]

www.linak.co.uk

ITALY

LINAK Italia S.r.l.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.it

JAPAN

LINAK K.K.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.jp

MALAYSIA

LINAK Actuators Sdn. Bhd.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.my

NETHERLANDS

LINAK Actuator-Systems B.V.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.nl

NEW ZEALAND

LINAK New Zealand Ltd.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.co.nz

NORWAY

LINAK Norge AS
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.no

POLAND

LINAK Polska
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.pl

REPUBLIC OF KOREA

LINAK Korea Ltd.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.kr

RUSSIAN FEDERATION

000 LINAK
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.ru

SPAIN

LINAK Actuadores, S.L.u
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.es

SWEDEN

LINAK Scandinavia AB
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.se

SWITZERLAND

LINAK AG
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.ch

TAIWAN

LINAK A/S Taiwan Representative Office
Phone: [phone]
Fax: [phone]
Mobile: [phone]
E-mail: [email protected]

www.linak.com.tw

TURKEY

LINAK İth. İhr. San. ve Tic. A.Ş.
Phone: + 90 312 4726338
Fax: + 90 312 4726635
E-mail: [email protected]

www.linak.com.tr

UNITED KINGDOM

LINAK UK Limited
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.linak.co.uk

IRAN

Bod Inc.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.bod.ir

PERU

Percy Martin Del Aguila Ubillus
Phone: [phone]

RUSSIAN FEDERATION

000 FAM
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.fam-drive.ru

SINGAPORE

Servo Dynamics Pte. Ltd.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

www.servo.com.sg

SOUTH AFRICA

Industrial Specialised Applications CC
Phone: [phone] or [phone] (Switch Board)
Fax: [phone]
E-mail: [email protected]
www.isaza.co.za

UNITED ARAB EMIRATES

Mechatronics
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
www.mechatronics.ae

For contact details on other countries please
visit www.linak.com or contact:

LINAK INTERNATIONAL

Phone: [phone]
Fax: [phone]
Fax: [phone] (Sales)
E-mail: [email protected]

www.linak.com