Lilin CMR70823.6 N/P, CMR70843.6 N/P, CMR70846 N/P, CMR70886 N/P, CMR70883.6 N/P Instruction Manual

...

Download

INSTRUCTION MANUAL

CMR7082/7084/7088 N/P 3.6/6

D/N ATR 700TVL IR CAMERA

CMR7082X3.6 N/P

D/N ATR 700TVL VARI-FOCAL IR CAMERA

IMPORTANT SAFEGUARDS

GRAPHIC SYMBOL EXPLANATION

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature

shock to persons.

accompanying the unit.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED

BYAN INCORRECT TYPE.

DISPOSE OF USED BATTERIESACCORDING

TO THE INSTRUCTIONS

CAUTION

Do not drop or strike this equipment.

Do not install the equipment near any naked flames or heat sources.

Do not expose this unit to rain or excessive moisture, avoid smoke and dust.

Do not cover cloth or to install this unit in poorly ventilated places.

Do not continue to operate if there appears to be fault.

Do not touch the power connection with wet hands.

Do not damage the power cord or leave it under pressure.

Sensitive electronics inside are vulnerable to excessive shock.

Excessive heat could damage this unit.

Please the camera in an environmental housing for protection. If the camera gets wet, unplug it and have it checked by qualified service personnel.

This may lead to overheating.

If the unit ceases to function, contact qualified service personnel for help.

Risk of short circuit or electric shock.

Risk of fire or shock circuit.

CONGRATULATIONS

Thank you for purchasing this D/N ATR 700TVL (Vari-Focal)IR Camera. You now own one of the many fine CCTV products we manufactured. This product has been carefully inspected under rigid quality control and should reach you in perfect condition. With reasonable care, it will provide years of reliable performance.

We recommend that you read this installation and operation manual thoroughly before installing and operation your new system.

Here you will find all the information you need to set up and use the system. If any questions are not answered in the manual, please contact your dealer. Before proceeding, please read and observe all instructions and warnings contained in this manual. Retain this manual with the original bill of sale for future reference and, if necessary, warranty service.

When unpacking your new camera, check for missing or damaged items. If any item is missing, or if damage is evident, I . Contact your dealer for assistance.

DO NOT

NSTALL OR OPERATE THIS PRODUCT

WARRANTY INFORMATION

Please complete the following product purchase information. The factory will requests this information when contacted for technical support, or warranty repair. It is also valuable in case of loss or theft.

Purchase Date Serial Number Model Number

TABLE OF CONTENTS

PART DESCRIPTION & DIMENSION INSTALLATION CONFIGURATION OF THE MENU

SETTING MENU AND FUNCTION To Open and Exit the Menu screen LENS SHUTTER/AGC WHITE BAL (White Balance) BACKLIGHT (Backlight Compensation) PICTADJUST (Picture Adjust) ATR (Adaptive Tone Reproduction) PRIVACY NR (Noise Reduction) CAMERA ID SYNC LANGUAGE CAMERA RESET

SPECIFICATIONS

1 2 7 9 9

9 10 12 14 15 16 16 17 18 19 19 19 20

TOP COVER BOTTOM CHASSIS BRACKET PANADJUSTMENT SCREW TILTADJUSTMENT SCREW WINDOW VIDEO OUTPUT JACK (CMR7082) DC POWER INPUT JACK ()DC12V 10%, CMR7082

Unit: mm

154

101

72.5

PART DESCRIPTION & DIMENSION

DC power input

Video output

INSTALLATION

FIG. 1

FIG. 2

1. CMR7082

1-1. Take out the camera from the inner box first. Plug the video cable and

power cable to video output jack and DC power input jack of the camera (FIG.1). Then fix bracket to the wall(FIG.2).

1-2. Loosen the screws of top cover with screw driver(FIG.3).

FIG. 3

2. CMR7084/8

2-1. Take out the camera from the inner box first. Loosen the pan adjustment

screw with hexagon screw driver. Then, separated the bracket from the camera body(FIG.4). Put the power cable and video cable through the bracket and then fix it to the wall(FIG.5&FIG.6).

FIG. 4

FIG. 6

FIG. 5

2-2. Open the top cover with screw driver(FIG.7).

FIG. 7

2-3. Next, Put the power cable and video cable through the bottom chassis and

rubble(FIG.8) and then fix the camera body on the bracket(FIG.9).

Video Output

Video Cable

FIG. 9

FIG. 8

2-4. Plug and fix the power cable to the terminal and plug the video cable to

vidoe output of the camera(FIG.10). Also for the security, please use the adhesive tape to wrap the connection of video cable(FIG.11).

FIG. 11

FIG. 10

Live

Earth

Neutral

Note :

When using two-cord power cable, please connect them to "Live" and "Neutral".

3. Loosen the pan and tilt adjustment screw on the bracket to turn the camera body to the desired angle and then tighten the screws(FIG.12).

4-1. USER OSD SETTING

Setting switches and Functions. A. (UP)

B. (LEFT)

FIG. 12

4. First, adjust the lens on focus and zoom to form the optimal video image after that tighten the screws(FIG.13). Then adjust the OSD menu to form the optimal image. Please refer to page7~19.

: Press to move the cursor upwards or to select

items.

: Press to move the cursor to the left and to select

or adjust the parameters of the selected item. The parameters changes each time this button is pressed.

FIG. 13

ZOOM

FOCUS

RIGHTLEFT

DOWN

SET

FIG. 15

5. Replace the top cover and tighten the screws(FIG.14&FIG.15).

FIG. 14

C. (RIGHT)

D. (DOWN)

E. SET : Executes selections and displays a submenu for an

item with the mark.

: Press to move the cursor to the right and

select or adjust the parameters of the selected item. The parameters changes each time this button is pressed.

: Press to move the cursor downwards or to select

items.

CONFIGURATION OF THE MENU

SETUP MENU

LENS

SHUTTER/ AGC

AUTO

MANUAL

HIGH LUMINANCE

LOW LUMINANCE

MODE SHUT+AGC SHUTTER 1/60(1/50) 1/100(1/120) 1/250~1/10000

AGC 6.00 12.00 18.00 24.00 30.00 36.00 42.00 44.80

///////

MODE

MODE AGC OFF

BRIGHTNESS(000~255)

BRIGHTNESS x0.25 x0.50 x0.75 x1.00

///

AUTO IRIS SHUT+AUTO IRIS

MODE AUTO OPEN CLOSE

SPEED(000~255)

TYPE DC

WHITE BAL

ATR

PICT ADJUST

BACKLIGHT BLC HLC OFF

ATW

OFF

MIRROR OFF/ ON

B-GAIN(000~255)

LUMINANCE LOW MID HIGH

SPEED(000~255)

PUSH

BRIGHTNESS(000~255) CONTRAST(000~255) SHARPNESS(000~255) HUE(000~255) GAIN(000~255)

R-GAIN(000~255)

CONTRAST LOW MIDLOW MID MIDHIGH HIGH

/// /

DELAY CNT(000~255)

USER 1

USER 2

ANTI CR MANUAL LEVEL(000~255) PUSH LOCK

ATW FRAME x0.50 x1.00 x1.50 x2.00

///

ENVIRONMENT INDOOR OUTDOOR

PRIVACY

OFF

AREA SEL 1/8~8/8

TOP [000~244(NTSC), 000~288(PAL)] BOTTOM [000~244(NTSC), 000~288(PAL)] LEFT [000~474(NTSC), 000~468(PAL)] RIGHT [000~474(NTSC), 000~468(PAL)] COLOR(1~8) TRANSP 0.00 0.50 0.75 1.00

///

MOSAIC OFF ON/

NR MODE Y/C OFF/ Y/ C

Y LEVEL(000~015) C LEVEL(000~015)

CAMERA ID

SYNC INT

LANGUAGE ENGLISH// / / / /

DEUTSCH FRANCAIS PYCCK PORTUGUES

ESPANOL

OFF ON

CAMERA RESET

SETTING MENU AND FUNCTION

TO Open and Exit the Menu screen

1. Press "SET" button. The Menu screen appears on the monitor. Check the current settings on the menu.

2. Push or button to select the options then use or button to select a mode.

NEXT: To the next setup menu. BACK: Return to the previous. RETURN: Return to the previous. SAVE ALL: Used to save the various setting of the internal OSD menu in the EEPROM together. EXIT: Exit the setup menu.

SETUP MENU

AUTO

AUTO ATW BLC

OFF OFF

LENS

SHUTTER/AGC WHITE BAL BACKLIGHT PICTADJUST ATR PRIVACY

NEXT EXIT SAVE ALL

SETUP MENU

OFF INT ENGLISH

CAMERA ID SYNC LANGUAGE CAMERA RESET

BACK EXIT SAVE ALL

LENS

This function is used to set the mechanical iris of the lens.

1. Select [LENS] option.

2. Push or button to select a mode. LENS mode changes as follows:

AUTO: Select the auto iris lens. MANUAL: Select the manual iris lens.

3. Select an AUTO then press "SET" button. The AUTO IRIS menu appears.

AUTO MANUAL

AUTO IRIS

AUTO

080

TYPE

MODE SPEED

RETURN

AUTO (AUTO IRIS)

FUNCTION OPTION DESCRIPTION

TYPE

SPEED

MODE

000~255

AUTO OPEN

Sets the type of mechanical iris. DC: Direct drive signal.

Sets the convergence speed of the mechanical iris.

Sets the type of control to be exercised over the mechanical iris. AUTO: The mechanical iris is controlled

automatically. OPEN: The mechanical iris is fixed to open. CLOSE: The mechanical iris is fixed to close.

1. Without LENS option in the CMR7082/7084/7088N/P .

2. Only DC mode on the TYPE option. Because a DC auto iris lens is used with the CMR7082X3.6N/P.

NOTES

SHUTTER/AGC

This function is used to set AE(Auto Exposure) or ME(Manual Exposure).

1. Select [SHUTTER/AGC] option.

2. Push or button to select an AUTO or MANUAL then press "SET" button. The AUTO SETUP or MANUAL SETUP menu appears. SHUTTER/AGC mode changes as follows:

AUTO: Select the AE control. MANUAL: Select the ME control.

AUTO MANUAL

AUTO SETUP

SHUT+AUTO IRIS

024

AGC x0.50

HIGH LUMINANCE

BRIGHTNESS

LOW LUMINANCE MODE BRIGHTNESS

RETURN

MODE

AUTO (AE)

FUNCTION OPTION DESCRIPTION

HIGH LUMINANCE

AUTO IRIS

SHUT+AUTO IRIS

Specifies AE control on the medium and high brightness side. AUTO IRIS: Fixed electronic shutter.

[1/60sec.(NTSC), 1/50sec.(PAL)] SHUT+AUTO IRIS: Auto electronic shutter.

[1/60sec.(1/50sec.)~1/100,000sec.]

MODE

000~255 Specifies the medium and high

brightness side reference.

BRIGHTNESS

LOW LUMINANCE

AGC

OFF

Specifies AE control on the low brightness side. AGC: AGC ON OFF: AGC OFF

MODE

x0.25 x0.50 x0.75 x1.00

Specifies the low brightness side reference.

BRIGHTNESS

MANUAL (ME)

FUNCTION OPTION DESCRIPTION

MODE SHUT+AGC "SHUT+AGC" is the only option available

for the ME operation mode. There are no other options.

MANUAL SETUP

SHUT+AGC

1/60

6.00

MODE

SHUTTER AGC

RETURN

AGC

SHUTTER

6.00

12.00

18.00

24.00

30.00

36.00

42.00

44.80

1/60(NTSC), 1/50(PAL)

1/100(NTSC), 1/120(PAL)

1/250

1/500 1/1000 1/2000 1/4000

1/10000

Sets the AGC value(dB) for ME.

Sets the ME shutter speed(in fractions of a second).

Please select AUTO mode on the SHUTTER/AGC option. If you select MANUAL mode, the over exposure may occur.

NOTE

WHITE BAL (WHITE BALANCE)

This function is used to set the white balance operation mode.

1. Select [WHITE BAL] option.

2. Push or button to select a mode. WHITE BAL mode changes as follows:

ATW PUSH USER1 USER2 PUSH LOCK MANUAL ANTI CR

ATW

239

016 x1.00 INDOOR

SPEED

DELAY CNT ATW FRAME ENVIROMENT

RETURN

ATW (Auto Tracking White balance) This function automatically tracks the changes in the color temperature, and adjusts the white balance. The color temperatures ranging from 1800K to 10500K.

FUNCTION OPTION DESCRIPTION

SPEED

DELAY CNT

ATW FRAME

ENVIROMENT

000~255 000~255

x0.50 x1.00 x1.50 x2.00

INDOOR

OUTDOOR

Adjusts the pull-in speed of ATW. Sets the time-based hysteresis of ATW.

Sets the pull-in frame magnification.

Sets the pull-in frame(indoor/outdoor) of ATW. INDOOR: Select the indoor pull-in frame. OUTDOOR: Select the outdoor pull-in frame.

PUSH (Full pull-in) This function adjusts the white balance regardless of the subject conditions.

USER2 WB

045 026

B-GAIN

R-GAIN

RETURN

USER1 WB

029 034

B-GAIN

R-GAIN

RETURN

USER1 The gain values for the outdoor fixed mode are used as the adjustment items of USER1 on the internal OSD menu.

USER2 The gain values for the fluorescent light fixed mode are used as the adjustment items of USER2 on the internal OSD menu.

FUNCTION OPTION DESCRIPTION

B-GAIN

R-GAIN

000~255

Used for the B gain operation in the WB fixed gain mode.

Used for the R gain operation in the WB fixed gain mode.

ANTI CR (Color Rolling suppression) This function minimizes the color changes(color rolling) over long periods caused by very small differences between the flicker frequency of non-inverter fluorescent lights and the drive frequency of the image sensor devices.

MANUAL (Manual WB) The B and R gain values for manual WB are set on this screen.

MANUAL WB

058

LEVEL

RETURN

FUNCTION OPTION DESCRIPTION

LEVEL 000~255 Sets the B and R gain values for manual WB.

By incrementing or decrementing the B gain value, the R gain value is also adjusted in tandem.

PUSH LOCK (Hold) The WB gain level established when operation has transferred to the PUSH LOCK mode is held.

1. Push or button to select [PUSH LOCK] Mode then press "SET" button.

BACKLIGHT (BACKLIGHT Compensation)

This function is used to set the backlight compensation operation.

1. Select [BACKLIGHT] option.

2. Push or button to select a mode. BACKLGIHT mode changes as follows:

BLC: Backlight compensation ON. HLC: HLC(High Light Compensation)

function ON. HLC is a function that improves the visual recognition of license plates and other such objects by suppressing or masking strong hight sources(such as the headlights of automobiles) in dark places.

OFF: Backlight Compensation OFF.

BLC HLC OFF

SETUP MENU

AUTO AUTO ATW

OFF OFF

BLC

LENS SHUTTER/AGC WHITE BAL

PICTADJUST ATR PRIVACY

NEXT EXIT SAVE ALL

BACKLIGHT

PICT ADJUST (PICTURE ADJUST)

1. Select [PICT ADJUST] option and press "SET" button. The PICT ADJUST menu appears.

2. Push or button to select a mode or set the function level(000~255). PICT ADJUST mode changes as follows:

MIRROR BRIGHTNESS CONTRAST GAIN HUE SHARPNESS

PICTADJUST

OFF

000 128 128 128 128

MIRROR

BRIGHTNESS CONTRAST SHARPNESS HUE GAIN

RETURN

FUNCTION OPTION DESCRIPTION

BRIGHTNESS

CONTRAST

SHARPNESS

HUE

GAIN

MIRROR

000~255 000~255 000~255 000~255 000~255

OFF

Sets the screen brightness. Sets the screen contrast. Sets the screen sharpness. Adjusts the hue. Adjusts the gain.

Sets the horizontal flip for the display output. OFF: Normal output. ON: Horizontal flipped output

ATR (Adaptive Tone Reproduction)

The ATR(Adaptive Tone Reproduction) function provides gradation compensation to improve the contrast of subjects whose gradation has been lost in cases where, for instance, both low-louminance areas and highluminance areas exist in the same picture.

1. Select [ATR] option.

2. Push or button to select a ON and press "SET" button. The ATR menu appears.

3. Push or button to set the luminance level and contrast level. LUMINANCE level changes as follows:

CONTRAST level changes as follows:

LOW MID HIGH

ATR

LOW

LUMINANCE

CONTRAST

RETURN

LOW MIDLOW MID MIDHIGH HIGH

FUNCTION OPTION DESCRIPTION

LUMINANCE

CONTRAST

LOW

MID

HIGH

LOW

MIDLOW

MID

MIDHIGH

HIGH

Sets the extent of the luminance compression.

Sets the extent of the contrast enhancement.

This function is used to set up to eight privacy masks.

1. Select [PRIVACY] option.

2. Push or button to select a ON and press "SET" button. The PRIVACY menu appears.

3. Push or button to select a mode or set the mask frame position.

PRIVACY

1/8

020 070 020 090

1.00 OFF

AREA SEL

TOP BOTTOM LEFT

RIGHT COLOR TRANSP MOSAIC RETURN

FUNCTION OPTION DESCRIPTION

AREA SEL

TOP

BOTTOM

LEFT

RIGHT

1/8, 2/8, 3/8, 4/8, 5/8, 6/8, 7/8, 8/8,

000~244(NTSC)

000~288(PAL)SI

000~244(NTSC)

000~288(PAL)SI

000~474(NTSC)

000~468(PAL)SI

000~474(NTSC)

000~468(PAL)SI

Selects the mask frame to be adjusted.

Sets the top side of the mask frame selected by the AREA SEL parameter.

Sets the bottom side of the mask frame selected by the AREA SEL parameter.

Sets the left side of the mask frame selected by the AREA SEL parameter.

Sets the right side of the mask frame selected by the AREA SEL parameter.

COLOR 1~8 Sets the colors of the mask frames.

TRANSP

MOSAIC

0.00

0.50

0.75

1.00

OFF

Sets the transparency ratio of the mask frames. The same transparency ratio value is set for all the mask frames.

Sets the mask frame mosaic function to ON or OFF. OFF: Mosaic function OFF. ON: Mosaic function ON.

NR (Noise Reduction)

This function is used to set the noise reduction.

1. Select [NR] option and press "SET" button. The NR menu appears.

2. Push or button to select one of four modes for NR or set the different filter strength. NR mode changes as follows:

Y/C

004 004

NR MODE

Y LEVEL C LEVEL

RETURN

Y/C OFF Y C

FUNCTION OPTION DESCRIPTION

NR MODE Y/C

OFF

Sets the 2D NR filter mode. Y/C: Y and C filters ON. OFF: Through Y: Y filter ON. C: C filter ON.

Y LEVEL C LEVEL

000~015 000~015

Sets the Y filter strength. Sets the C filter strength.

CAMERA ID

This function is used to set the camera ID.

1. Select [CAMERA ID] option.

2. Use or button to select a ON and press "SET" button. The CAMERA ID menu appears.

CAMERA ID

RETURN

(

)

YDZ

0F1G2H3

8N9

-P!Q"

U&V

CHR1 CHR2

CLR POS

CAMERA ID

RETURN

CHR1 CHR2

CLR POS

3.Use,,orbutton to select a letter, numeral or symbol.

(Blank): Inserts a space at the cursor position. CHR1: Letters A to Z, numerals 0 to 9, symbols. CHR2: 40 traditional Chinese.

: Moves cursor to left, right, up or down. CLR: If you enter the wrong code, select CLR then press "SET" button. POS: Us

e,,orbutton to move position of CAMERA ID on the

screen.

SYNC

This function is used to display the current synchronization mode. The SYNC mode is fixed to the INT(Internal synchronization).

SETUP MENU

OFF

ENGLISH

INT

NR CAMERA ID

LANGUAGE CAMERA RESET

BACK EXIT SAVEALL

SYNC

LANGUAGE

This function is used to select the language in which to display the internal OSD menu.

1. Select [LANGUAGE] option.

2. Push or button to select a language.

SETUP MENU

OFF INT

ENGLISH

SYNC

CAMERA ID

CAMERA RESET

BACK EXIT SAVE ALL

LANGUAGE

CAMERA RESET

This function is initializes all the internal OSD menu setting together.

1. Select [CAMERA RESET] option.

2. Press "SET" button to reset the camera setting to initial setting.

SETUP MENU

OFF INT ENGLISH

SYNC LANGUAGE

CAMERA ID

BACK EXIT SAVE ALL

CAMERA RESET

SPECIFICATIONS

Model No.

Lens

Power Input Voltage System

Sync. Mode

Menu Control

Pick Up Element

Effective Pixels

Chip Size Horizontal & Vertical

Sync. Frequency

Scanning System

Resolution Minimum Illumination

Shutter

Adaptive Tone Reproduction

S/N Ratio

Auto Gain Control White Balance

Noise Reduction Picture Adjust Privacy Masking Privacy Masking Zone OSD Language

Power Consumption

Back Light Compensation

Video Output

Operating Temperature

Gamma Characteristic

IP Rating Window

Infrared LED

Beam Spread

Peak Wavelength

Focal Length Iris

Angle of view

Auto

Luminance

Manual

Contrast

CMR7082N/P3.6

1/60(1/50)S ~ 1/100,000S

LOW / MID / HIGH

1/60(1/50)S, 1/100(1/120)S, 1/250S, 1/500S, 1/1,000S, 1/2,000S, 1/4,000S, 1/10,000S

LOW / MIDLOW / MID / MIDHIGH / HIGH

NTSC or PAL

AC24V ( 10%)

Internal

OSD Control

1/3" Exview HAD CCD Sensor

976(H) x 494(V) [NTSC]

976(H) x 582(V) [PAL]

5.58mm(H) x 4.67mm(V)

15.734 KHz / 59.94Hz [NTSC]

15.625 KHz / 50Hz [PAL]

2:1 Interlace

Color: 700TV Lines, Mono: 750TV Lines

0.2Lux/F1.8, 0Lux(IR On)

More Then 50dB (AGC-OFF)

AUTO / MANUAL

ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH LOCK

Y/C/Y/C/OFF

MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN

ON / OFF

8 Zones

ENGLISH/JAPANESE/GERMANS/FRENCH/RUSSIAN/PORTUGUESE/SPANISH/SIMPLY CHINESE

7.8W

BLC / HLC(High Light Compensation) / OFF

IP66

65 Heat Resistant Glass

850nm

CVBS 1.0Vp-p, 75ohm

-10 ~ +50

(14 ~ 122 )

=0.45

D/N ATR 700TVL IR CAMERA

AC100~240V

3.6mm F2.0

54.5 92

Radiant Distance

Dimension Weight

30M

Body:82mm(W) x 72.5mm(H) x 154mm(D), Bracket: 101mm(L)

530g

Design and specifications are subject to change without notice.

CMR7082N/P6 CMR7084N/P3.6 CMR7084N/P6 CMR7088N/P3.6 CMR7088N/P6

DC12V ( 10%)

6mm

F1.8

44.5

33.1 56

3.6mm F2.0

54.5 92

6mm

F1.8

44.5

33.1 56

3.6mm F2.0

54.5 92

6mm F1.8

44.5

33.1 56

11W

540g

66-CMR708CSE-1

Model No.

Lens

Power Input Voltage System

Sync. Mode

Menu Control

Pick Up Element

Effective Pixels

Chip Size Horizontal & Vertical

Sync. Frequency

Scanning System

Infrared Cut Filter Resolution

Minimum Illumination

Shutter

Adaptive Tone Reproduction

S/N Ratio

Auto Gain Control White Balance

Noise Reduction Picture Adjust Privacy Masking Privacy Masking Zone OSD Language

Power Consumption

Back Light Compensation

Video Output

Operating Temperature

Gamma Characteristic

IP Rating Window

Infrared LED

Beam Spread

Peak Wavelength

Focal Length Iris

Angle of view

Color

Auto

Luminance

Mono

Manual

Contrast

IR On

CMR7082X3.6N/P

0.045Lux / F1.4

1/60(1/50)S ~ 1/100,000S

LOW / MID / HIGH

0.009Lux / F1.4

1/60(1/50)S, 1/100(1/120)S, 1/250S, 1/500S, 1/1,000S, 1/2,000S, 1/4,000S, 1/10,000S

LOW / MIDLOW / MID / MIDHIGH / HIGH

NTSC or PAL

DC12V ( 10%)

Internal

OSD Control

1/3" Exview HAD CCD Sensor

976(H) x 494(V) [NTSC]

976(H) x 582(V) [PAL]

5.58mm(H) x 4.67mm(V)

15.734 KHz / 59.94Hz [NTSC]

15.625 KHz / 50Hz [PAL]

2:1 Interlace

Color: 700TV Lines, Mono: 750TV Lines

0Lux

More Then 50dB (AGC-OFF)

Auto Selectable, Automatic Switch From Color Mode to Monochrome

AUTO / MANUAL

ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH LOCK

Y/C/Y/C/OFF

MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN

ON / OFF

8 Zones

ENGLISH/JAPANESE/GERMANS/FRENCH/RUSSIAN/PORTUGUESE/SPANISH/SIMPLY CHINESE

6.8W

BLC / HLC(High Light Compensation) / OFF

IP66

65 Heat Resistant Glass

850nm

CVBS 1.0Vp-p, 75ohm

-10 ~ +50

(14 ~ 122 )

=0.45

D/N ATR 700TVL VARI-FOCAL IR CAMERA

3.3 ~ 12mm F1.4

89.8 ~ 23.9

63.6 ~ 17.9

125.7 ~ 29.9

Radiant Distance

Dimension Weight

30M

Body:82mm(W) x 72.5mm(H) x 154mm(D), Bracket: 101mm(L)

550g

Design and specifications are subject to change without notice.

MERIT LILIN ENT. CO., LTD

http://www.meritlilin.com

CMR7082/7084/7088 N/P 3.6/6

66-CMR708CSE

D/N ATR 700TVL IR CAMERA

CMR7082X3.6 N/P

D/N ATR 700TVL VARI-FOCAL IR CAMERA

Lilin CMR70823.6 N/P, CMR70843.6 N/P, CMR70846 N/P, CMR70886 N/P, CMR70883.6 N/P Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual