LigoWave NFT1NI User Manual

NFT 1Ni manual

User’s Guide

Revision 1.0

this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Deliberant.

Notice

Deliberant reserves the right to change specifications without prior notice. While the information in this manual has been compiled with great care, it may not be deemed an

assurance of product characteristics. Deliberant shall be liable only to the degree specified in the terms of sale and delivery.

The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is subject to written authorization from Deliberant.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement

This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 50 cm between the radiator and user body.

If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: V2V-NFT1NI Or Contains FCC ID: 7607ANFT1NI”

When the module is installed inside another device, the user manual of this device must contain below warning statements;

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

deliberant Page 2

(1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product

Important note:

This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. 50 cm minimum distance has to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for a population/uncontrolled environment can be satisfied.

Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.

IC Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Cetappareilestconforme aux CNR exemptes de licenced'IndustrieCanada . Son fonctionnementestsoumis aux deux conditions suivantes : ( 1 ) Cedispositif ne peut causer d'interférences ; et ( 2 ) Cedispositifdoit accepter touteinterférence , y compris les interférences qui peuvent causer un mauvaisfonctionnement de l'appareil.

IC Radiation Exposure Statement: This modular complies with IC RF radiation exposure limits set forth for an uncontrolled

environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 50 cm between the radiator and user body.

Cettemodulairedoitêtreinstalléetutilisé à une distance minimum de 50 cm entre le radiateur et le corps de l'utilisateur.

If the IC number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 7607A-NFT1NI”

When the module is installed inside another device, the user manual of this device must contain below warning statements;

1. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

deliberant Page 3

The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product

Important Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 50cm between the radiator & your body.

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 50 cm de distance entre la source de rayonnement et votre corps.

This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module.

Trademarks

Deliberant logo is trademark of Deliberant LLC.

All other registered and unregistered trademarks in this document are the sole property of their respective owners.

deliberant Page 4

User’s Guide

Contents

Copyright ............................................................................................................................................. 2

Notice .................................................................................................................................................. 2

FCC Statement .................................................................................................................................... 2

IC Statement ....................................................................................................................................... 3

Trademarks ......................................................................................................................................... 4

CONTENTS ........................................................................................................................................... 5

ABOUT THIS GUIDE ............................................................................................................................. 6

Prerequisite Skills and Knowledge ...................................................................................................... 6

Conventions Used in this Document ................................................................................................... 6

Abbreviation List .................................................................................................................................. 6

FWBD-1907 SPECIFICATION .............................................................................................................. 8

FIRST CONNECTION .......................................................................................................................... 11

CONFIGURATION GUIDE .................................................................................................................. 13

Appling and Saving Configuration Changes ..................................................................................... 13

Status ................................................................................................................................................ 13

Information ..................................................................................................................................... 14

Statistics ......................................................................................................................................... 15

Wireless ......................................................................................................................................... 16

Settings .............................................................................................................................................. 18

Network Configuration ................................................................................................................... 18

Bridge Mode ................................................................................................................................... 18

Router IPv4 Mode .......................................................................................................................... 22

Wireless ......................................................................................................................................... 25

Wireless Mode: Access Point (auto WDS) ................................................................................................ 25

Wireless Mode: Access Point (iPoll 2) ....................................................................................................... 29

Wireless Mode: Station (WDS/iPoll 2) ....................................................................................................... 32

Wireless Mode: Station (ARPNAT) ........................................................................................................... 34

Wireless Security ...................................................................................................................................... 39

Wireless ACL ............................................................................................................................................ 42

Services Configuration ................................................................................................................... 44

Date & time ............................................................................................................................................... 44

Remote Management ................................................................................................................................ 45

SNMP ........................................................................................................................................................ 46

Ping watchdog ........................................................................................................................................... 46

WNMS ....................................................................................................................................................... 47

System Configuration .................................................................................................................... 47

Device settings ............................................................................................ ..............................................47

System functions ....................................................................................................................................... 48

User accounts ................................................................ ................................................................ ........... 48

LED settings .............................................................................................................................................. 49

Advanced settings ..................................................................................................................................... 49

Firmware Upgrade ......................................................................................................................... 50

Tools .................................................................................................................................................. 52

Antenna Alignment ........................................................................................................................ 52

Site Survey ..................................................................................................................................... 53

Link Test ........................................................................................................................................ 53

Support .............................................................................................................................................. 54

Troubleshooting ............................................................................................................................. 54

System Log .................................................................................................................................... 55

deliberant Page 5

User’s Guide

Additional information that may be helpful but which is not required.

Important information that should be observed.

bold

Menu commands, buttons, input fields, links, and configuration keys are displayed in bold

italic

References to sections inside the document are displayed in italic.

code

File names, directory names, form names, system-generated output, and user typed entries are displayed in constant-width type

Abbreviation

Description

ACL

Access Control List

AES

Advanced Encryption Standard

AMSDU

Aggregated Mac Service Data Unit

Access Point

CRC

Cyclic Redundancy Check

DHCP

Dynamic Host Control Protocol

EAP

Extensible Authentication Protocol

GHz

Gigahertz

GMT

Greenwich Mean Time.

GUI

Graphical User Interface

About this Guide

Prerequisite Skills and Knowledge

To use this document effectively, you should have a working knowledge of Local Area Networking (LAN) concepts and wireless Internet access infrastructures.

Conventions Used in this Document

The following typographic conventions and symbols are used throughout this document:

Abbreviation List

deliberant Page 6

User’s Guide

Abbreviation

Description

IEEE

Institute of Electrical and Electronics Engineers

IGMP

Internet Group Management Protocol

ISP

Internet Service Provider

Internet Protocol

LAN

Local Area Network

LED

Light-Emitting Diode

MAC

Media Access Control

Mbps

Megabits per second

MHz

Megahertz

MIMO

Multiple Input, Multiple Output

MSCHAPv2

Microsoft version of the Challenge-handshake authentication protocol, CHAP.

NAT

Network address translation – translation of IP addresses (and ports)

Personal Computer

PDA

Personal Digital Assistant

PTP

Point To Point

PSK

Pre-Shared Key

QoS

Quality of Service

PEAP

Protected Extensible Authentication Protocol

RSSI

Received Signal Strength Indication – received signal strength in mV, measured on BNC outdoor unit connector

Receive

SISO

Simple Input, Simple Output

SNMP

Simple Network Management Protocol

SMTP

Simple Mail Transfer Protocol

SSID

Service Set Identifier

TCP

Transmission Control Protocol

TKIP

Temporal Key Integrity Protocol

TTLS

Tunneled Transport Layer Security (EAP-TTLS) protocol

Transmission

UDP

User Datagram Protocol

UAM

Universal Access Method

VLAN

Virtual Local Area Network

VoIP

Voice over Internet Protocol

WDS

Wireless Distribution System

WEP

Wired Equivalent Privacy

WISPr

Wireless Internet Service Provider roaming

WLAN

Wireless Local Area Network

WPA

Wi-Fi Protected Access

WPA2

Wi-Fi Protected Access 2

deliberant Page 7

User’s Guide

NFT 1Ni specification

The NFT 1Ni is a versatile, very efficient, and stable 2.4 GHz hardware platform. Platform is equipped

with high output power 802.11n MIMO radio.

The robust hardware is coupled with an advanced and feature-rich operating system optimized for

high performance communications which allows compatibility with older 802.11b/g standard while

adding support for the latest wireless communications.

Block diagram

Note 1: Antenna 0 and Antenna 1 frequency range is 2412MHz - 2462MHz (CH1 to CH13).

Note 2: FEM - Front End Module. FEM includes RF PA, RF Switch and RF LNA.

Note 3: BPF – Band Pass Filter.

Note 4: LPF – Low Pass Filter.

Note 5: AR9341 contains contains internal Voltage Regulator making +1.2V from 3.3V.

deliberant Page 8

User’s Guide

Feature

Description

Notes

CPU

AR9341

RAM

64MB

Flash memory

16MB

Watchdog timer

Built into CPU

Reset push button

Connected to GPIO

LED’s

6 LED’s connected to

GPIO

Power, LAN, 4x received signal strength

Ethernet

2x 10/100 Ethernet port

Power options

Power-Over-Ethernet or DC Jack

PoE polarity independent via Eth pins 4/5 and7/8.

Power supply

24V

Serial port (UART)

Test points

3.3V TTL level, not end user accessible

Operating temperature range

From 0C to +65C

Humidity

0 ~ 90 % (non-condensing)

Power consumption

up to 4.6W

Parameter

Description

WLAN standard

IEEE 802.11 b/g/n

Radio mode

MIMO 2x2

Radio frequency band

2.412 GHz to 2.462 GHz

Channel size

20, 40MHz

Modulation schemes

802.11 g/n: OFDM (64-QAM, 16-QAM, QPSK, BPSK)

802.11 b: DSS (CCK, DQPSK, DBPSK)

Data rates

802.11 n: 300, 270, 240, 180, 120, 90, 60, 30 Mbps

802.11 g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps

802.11 b: 11, 5.5, 2, 1 Mbps

Hardware information

Wireless information

deliberant Page 9

User’s Guide

Features

General

Ability to define/limit frequency, channel width, EIRP, modulation

Advanced wireless functionality

Auto-channel, auto-modulation

Operating mode

Router, Bridge

Wireless operating modes

AP auto WDS, Station, Station WDS, Virtual radios (VSSID), iPoll access point, iPoll client

Wireless security

WPA/WPA2 Personal, WPA/WPA2 Enterprise

Wireless QoS

WMM

WAN protocols

Static IP, DHCP client, PPPoE client

Network

NAT

Services

DHCP server, SNMP server, Wireless and Ethernet statistics

Management

HTTP GUI, SSH CLI, SNMP read, WNMS, troubleshooting file, reset via reset tool

Tools

Site survey, Antenna alignment

State

Current

Voltage

Power consumption

Idle

103 mA

24 V

2.47 W

Max load

192 mA

24 V

4.61 W

Software

Power consumption

deliberant Page 10

User’s Guide

The default administrator login settings are: Login: admin Password: admin01

First Connection

The default product address is 192.168.2.66.

Follow the steps for first connection to the device:

Step 1. Connect an Ethernet cable between your computer and the AP. Step 2. Make sure your computer is set to the same subnet as the AP, i.e. 192.168.2.150 Step 3. Start your Web browser. Step 4. Each devices uses following default settings:

 WAN IP: 192.168.2.66  Subnet mask: 255.255.255.0  Username: admin  Password: admin01

The initial login screen looks as follow:

deliberant Page 11

User’s Guide

Step 5. Confirm the user agreement. According to the chosen country the regulatory domain

settings may differ. You are not allowed to select radio channels and RF output power values other the permitted values for your country and regulatory domain.

Step 6. After successful administrator login you will see the main page of the device Web

management interface. The device now is ready for configuration.

deliberant Page 12

User’s Guide

It is not required to press Save changes in every Web GUI tab. The device remembers all changes made in every tab and after action button is used, all changes will be applied.

Configuration Guide

This document contain product‘s powerful web management interface configuration description allowing setups ranging from very simple to very complex.

Appling and Saving Configuration Changes

There are three general buttons located on the right top corner of the WEB GUI allowing managing device configuration:

Save changes – if pressed new configuration settings are applied instantly and written to the

permanent device memory.

Test changes – if pressed the device will start operating with newly set configuration settings for

3 minutes. During this test time the administrator is able to gauge if device is working properly, and then Save changes. In case wrong settings were chosen (or even after faulty settings administrator have lost connection with the device), the device automatically reverts back configuration to an old one.

Discard changes – if pressed parameter changes are discarded. It should be noted that if Save

changes is pressed it is not possible to discard changes.

Status

After login, the main Web management page displays Status Information page. The header of Web management page displays main information about device: Firmware version, Product name, Uptime, CPU load, Ethernet port(s) status, Connected client count.

Figure 1 - Web Management Interface

deliberant Page 13

User’s Guide

Information

The Information page displays a summary of status information of your device. It shows important information for the APC operating mode, radio and network settings.

Figure 2 – Device Information Page

Radio – displays summary of the radio interface configuration. Wireless – displays general information about the wireless connection. The wireless information will

differ on Access Point, Station, iPoll wireless modes:  Access point (autoWDS) and (Access Point (iPoll 2) – displays access point operating

information: SSID, Security type, SSID Broadcast status, VLAN and number of connected clients.

 Station (WDS/iPoll) and Station (ARPNAT) – displays settings at which the station is connected

to the access point: SSID, Security type, Peer’s MAC address, Tx/Rx rate, Protocol.

Network mode – displays short summary about current network configuration (bridge or router).

deliberant Page 14

User’s Guide

Statistics

The Statistics sections id divided into two sections and displays network interface counters and traffic graphs of wired and wireless interfaces:

Figure 3 – Network Statistics: Interface counters

Interface counters – displays table of interface statistics. The SSID name is displayed in the brackets near the radio interface (and VAPs).

MAC address– displays the MAC address of the particular interface. Tx data – displays the transmitted data. Rx data – displays the received data. Tx packets – displays the number of transmitted packets. Rx packets – displays the number of received packets. Tx errors – displays the number of the TX errors. Rx errors – displays the number of the RX errors.

The wired and wireless interface graphs display real-time data traffic. If particular device is working as Station, the additional graph of the signal and noise levels will be displayed:

deliberant Page 15

User’s Guide

Status Wireless section is not available if APC is operating as Station (WDS/iPoll) or Station (ARPNAT). In this case all necessary information about wireless connection with AP unit will be on

Information page, wireless table.

Wireless

The Wireless page displays the receive/transmit statistics between AP and successfully associated wireless clients (click Counters tab, if necessary to view information of connected clients in Rx/Tx counters):

Figure 4 – Access Point's Wireless Statistics

deliberant Page 16

User’s Guide

In case the access point has more than one wireless interface (VAPs), the appropriate number of tables with information about connected wireless clients will be displayed.

Station – displays MAC address and Friendly name of the successfully connected wireless client. IP address – displays wireless client IP address. Signal – indicates the signal strength of the access point main and auxiliary antennas that the station

communicates with displayed dBm.

Tx/Rx rate – displays transmit/receive data rates in Mbps. Tx/Rx CCQ, % - displays the wireless Client Connection Quality (CCQ), the value in percent that

shows how effective the bandwidth is used regarding the theoretically maximum available bandwidth.

Protocol – displays the protocol at which the access point communicates with the particular station. Link uptime – displays the duration of the particular session. Kick selected – select to end the connection to this station.

deliberant Page 17

User’s Guide

Settings

Network Configuration

The Settings | Network Configuration page allows you to control the network configuration of the device. First, the device operation mode must be defined to work as a bridge or router (IPv4 or IPv6). The content of the window varies depending on your selection:

Figure 5 – Network Mode Options

Network mode – choose the device operating mode. Network settings will vary according to the selected Network mode. The Bridge mode allows configuring device IPv4 and IPv6 LAN IP settings, while the Router mode requires more parameters such as LAN network settings, WAN network settings, LAN DHCP settings.

Bridge Mode

When device is configured to operate in Bridge mode, only device LAN settings should be configured on the Network configuration page:

deliberant Page 18

User’s Guide

When assigning IP address make sure that the chosen IP address is unused and belongs to the same IP subnet as your wired LAN, otherwise you will lose the connection to the device from your current PC. If you enable the DHCP client, the browser will lose the connection after saving, because the IP address assigned by the DHCP server is not predictable.

Figure 6 – Bridge Mode Settings

Enable management VLAN – enable a VLAN tagging for management traffic. Access to the AP for management purposes can further be limited using VLAN tagging. By defining Management VLAN, the device will only accept management frames that have the appropriate Management VLAN ID. All other frames using any management protocol will be rejected.

Management VLAN ID – specify the VLAN ID [2-4095]. When device interfaces are configured with a specific VLAN ID value, only management frames that matching configured VLAN ID will be accepted by device.

IPv4 Configuration

IP method – specify IP reception method: IP addresses can either be retrieved from a DHCP server or configured manually:

 Static – the IP address must be specified manually.  Dynamic – the IP address for this device will be assigned from the DHCP server. If DHCP server

is not available, the device will try to get an IP. If has no success, it will use pre-configured fallback IP address. The fallback IP settings can be changed to custom values.

IP address – specify IP address for device Subnet mask – specify a subnet mask for device. Default gateway – specify a gateway IP address for device.

deliberant Page 19

User’s Guide

DNS server – specify the Domain Naming Server. Secondary IP – specify the alternative IP address and the netmask for APC unit management.

IPv6 Configuration

Click the IPv6 slide to enable IPv6 configuration:

Figure 7 – Bridge IPv6 Settings

IPv6 method – specify IPv6 reception method: IPv6 addresses can either be retrieved from a DHCPv6 server or configured manually:

 Static – the IPv6 address must be specified manually.  Dynamic stateless IP – the DHCPv6 client only obtains network parameters other than IPv6

address

 Dynamic stateful IP – the DHCPv6 clients require IPv6 address together with other network

parameters (e.g. DNS Server, Domain Name, etc.).

IPv6 address – specify the IPv6 Address for the interface. IPv6 prefix length– enter the Prefix Length for the address.

deliberant Page 20

User’s Guide

IPv6 default gateway – specify IPv6 address for default gateway. IPv6 DNS server – specify the Domain Naming Server IPv6 addresses.

deliberant Page 21

User’s Guide

Router IPv4 Mode

This section allows customizing parameters of the Router to suit the needs of network, including ability to use the built-in DHCP server. When device is configured to operate as Router, the following sections should be specified: WAN network settings, LAN network settings and LAN DHCP settings.

Figure 8 – Router IPv4 Settings

Enable NAT – select to enable NAT (Network Address Translation), that functions by transforming the private IP address of packets originating from hosts on your network so that they appear to be coming from a single public IP address and by restoring the destination public IP address to the appropriate private IP address for packets entering the private network, the multiple PCs on your network would then appear as a single client to the WAN interface.

WAN Settings

WAN network settings include settings related to the WAN interface. The access type of the WAN interface can be configured as: Static IP, Dynamic IP, PPPoE client.

IP method – choose Static to specify IP settings for device WAN interface:

deliberant Page 22

User’s Guide

Figure 9 – Router IPv4 WAN Settings: Static IP

IP address – specify static IP address. Subnet mask – specify a subnet mask. Default gateway – specify a gateway. DNS server – specify primary and/or secondary DNS server Secondary IP – enable to specify the alternative IP address and the netmask for APC unit

management.

WAN mode – choose Dynamic to enable DHCP client on the WAN side. This option does not need any parameters:

Figure 10 – Routers IPv4 WAN Settings: Dynamic IP

DHCP fallback setting – specify IP address, Subnet mask, Default gateway and optionally DNS server for DHCP fallback. In case the APC unit will not get the IP address from the DHCP, the specified fallback IP settings will be used.

Enable secondary IP – specify the alternative IP address and the netmask for APC unit management.

DNS servers – allows selecting if automatically assigned or alternative DNS servers should be used

deliberant Page 23

User’s Guide

WAN mode – choose PPPoE to configure WAN interface to connect to an ISP via a PPPoE:

Figure 11 – Routers IPv4 WAN Settings: PPPoE client

User name – specify the user name for PPPoE. Password – specify the password for PPPoE. MTU – specify the MTU (Maximum Transmission Unit) in bytes. Enable secondary IP – specify the alternative IP address and the netmask for APC unit

management. DNS settings – allows selecting if automatically assigned or alternative DNS servers should be used.

LAN Network Settings

LAN configuration include settings related to the LAN interface.

Figure 12 – Router LAN Settings

IP address – specify the IP address of the device LAN interface. Subnet mask – specify the subnet mask of the device LAN interface. Enable DHCP server – select to enable DHCP server on LAN interface.

 IP address from – specify the starting IP address of the DHCP address pool.  IP address to – specify the ending IP address of DHCP address pool.  Lease time – specify the expiration time in seconds for the IP address assigned by the DHCP

server.

deliberant Page 24

User’s Guide

Before changing radio settings manually verify that your settings will comply with local government regulations. At all times, it is the responsibility of the end-user to ensure that the installation complies with local radio regulations.

Wireless

The APC device can operate in four wireless modes: Access Point (autoWDS), Access Point (iPoll 2), Station (auto iPoll 2) and Station (ARPNAT).

Figure 13 – Device Wireless Operating Mode

Depending on the wireless operation mode selection some of the displayed configuration parameters will differ (e.g. security or advanced wireless settings).

Operating mode – select wireless operation mode:  Station (auto iPoll 2) – with this wireless mode the APC will act as Station and will automatically

turn on iPoll 2 mode if detects that selected AP is operating in iPoll 2 protocol.

 Station (ARPNAT) – in this mode Station connects to other radios operating as an Access Point.

Wireless Mode: Access Point (auto WDS)

Enable radio – use slide to enable or disable APC radio. Operating country - displays APC unit operating country. The Country selection determines the

available channels and transmission power level based on regulatory restrictions in the operating country. The country has been selected on the first step of the APC unit's installation, though can be updated if required.

deliberant Page 25

User’s Guide

IEEE mode – specify the wireless network mode. Tx power (dBm) – set the unit’s transmitting power at which the device will transmit data. The larger

the distance, the higher transmit power is required. To set transmit power level use the slider or enter the value manually. When entering the transmit power value manually, the slider position will change according to the entered value. The maximum transmit power level is limited to the allowed value by country in which device is operating regulatory agency.

Channel – displays the channel at which the AP is operating, or indicates that autochannel function is used. Click the button and the channel selection window will be displayed:

Channel width – The default channel bandwidth for 802.11 radio is 20MHz. The 802.11n allow channel bonding in such way the total channel width becomes 40MHz.

Channel table – select the channel(s) at which the Access Point will operate. If more than one channel is selected, then autochannel feature will be enabled. Automatic channel selection allows AP to select a channel which is not used by any other wireless device or, if there are no free channels available - to select a channel which is least occupied. The table displays detailed information about each channel: TX limit, EIRP limit.

Advanced Radio Settings

Advanced parameters allow configuring the device to get the best performance/capacity of the link. Max 802.11n MCS index – choose the maximum rates to specify the modulation and coding scheme

(MCS) rates at which data can be transmitted between the access point and the client. If there will be an interference encountered, the APC will step down to the highest rate that allows data transmission.

Max legacy data rate – choose the maximum data rate in Mbps at which AP should transmit packets. The AP will attempt to transmit data at the highest data rate set. If there will be an interference encountered, the APC will step down to the highest rate that allows data transmission.

AMSDU – enable the AMSDU packet aggregation. If enabled, the maximum size of the 802.11 MAC frames will be increased.

Short GI – enable short guard interval. If selected, then 400ns value will be used, else 800ns. RTS/CTS – specify the RTS threshold using slider or enter the value manually [0-2347 bytes]. The

RTS threshold determines the packet size of a transmission and, through the use of an access point, helps control traffic flow.

ACK timeout – specify the ACK timeout using slider or enter the value manually. Ack timeout can be entered by defining the link distance or specifying time value. Too low value of the ACK timeout will give very low throughput. A high value may slow down the link in noisy environment. A low value is far worse than a value slightly too high. ACK Timeout value should be tuned to the optimal value for the maximum link throughput.

deliberant Page 26

User’s Guide

For detailed information about security settings and WACL refer at the respective sections Wireless Security and Wireless ACL.

Wireless Settings (AP)

Figure 14 - Wireless Settings

The wireless table allows configure main AP parameters, such as SSID, Security, WACL, etc. Click on the edit icon and the wireless settings window will be displayed:

Figure 15 – Wireless AP Settings

SSID – specify the SSID of the wireless network device. Broadcast SSID – enables or disables the broadcasting of the SSID for AP.

deliberant Page 27

User’s Guide

Advanced AP Settings

Client isolation – select to enable the layer 2 isolation that blocks clients from communicating with each other. Client isolations is available only in Access Point (auto WDS) and Access Point Repeater mode.

Map to data VLAN ID – specify the VLAN ID for traffic tagging on particular radio interface. The Station devices that associate using the particular SSID will be grouped into this VLAN.

Max connected clients - specify the maximum number of associated wireless clients on the AP radio.

Min client signal (dBm) - if enabled, the AP will drop the connection for clients that have signal level below configured threshold.

Quality of service (WMM) – enable to support quality of service for prioritizing traffic. Management over wireless – controls the wireless administrative access. For security reasons, it is

recommended disable wireless access and instead requires a physical network connection using an Ethernet cable for administrative access to APC.

deliberant Page 28

User’s Guide

Wireless Mode: Access Point (iPoll 2)

Figure 16 – iPoll Access Point’s Wireless Settings

Enable radio – use slide to enable or disable APC radio. Operating country - displays APC unit operating country. The Country selection determines the

Tx power (dBm) – set the unit’s transmitting power at which the device will transmit data. The larger the distance, the higher transmit power is required. To set transmit power level use the slider or enter the value manually. When entering the transmit power value manually, the slider position will change according to the entered value. The maximum transmit power level is limited to the allowed value by country in which device is operating regulatory agency.

Channel – displays the channel at which the AP is operating, or indicates that autochannel function is used. Click the button and the channel selection window will be displayed:

Channel width – The default channel bandwidth for 802.11 radio is 20MHz. The 802.11n allow channel bonding in such way the total channel width becomes 40MHz.

Channel table – select the channel(s) at which the Access Point iPoll 2 will operate. If more than one channel is selected, then autochannel feature will be enabled. Automatic channel selection allows AP to select a channel which is not used by any other wireless device or, if there are no free channels available - to select a channel which is least occupied. The table displays detailed information about each channel: TX limit, EIRP limit.

deliberant Page 29

User’s Guide

Advanced Radio Settings

Max data rate (Mbps) – choose the maximum rates to specify the modulation and coding scheme (MCS) rates at which data can be transmitted between the access point and the client. If there will be an interference encountered, the APC will step down to the highest rate that allows data transmission.

Wireless Settings (AP)

Figure 17 - Wireless Settings

The wireless table allows configure main AP parameters, such as SSID, Security, WACL, etc. Click on the edit icon and the wireless settings window will be displayed:

Advanced AP Settings

Map to data VLAN ID – specify the VLAN ID for traffic tagging on particular radio interface. The Station devices that associate using the particular SSID will be grouped into this VLAN.

Max connected clients - specify the maximum number of associated wireless clients on the AP radio.

Min client signal (dBm) - if enabled, the AP will drop the connection for clients that have signal level below configured threshold.

Quality of service (WMM) – enable to support quality of service for prioritizing traffic.

deliberant Page 30

User’s Guide

Management over wireless – controls the wireless administrative access. For security reasons, it is recommended disable wireless access and instead requires a physical network connection using an Ethernet cable for administrative access to APC.

deliberant Page 31

User’s Guide

Wireless Mode: Station (WDS/iPoll 2)

With this wireless mode, the APC will operate as wireless Station, though it automatically switch on the iPoll 2 mode if the specified access point will be detected as an AP iPoll 2. If the Station finds two networks with the same SSID, where one is iPoll 2, another 11n, the connection priority will be iPoll 2.

Enable radio – use slide to enable or disable APC radio. Operating country - displays APC unit operating country. The Country selection determines the

Channel width - The default channel bandwidth for 802.11 radio is 20MHz. The 802.11n allow channel bonding in such way the total channel width becomes 40MHz.

Advanced Radio Settings

Advanced parameters allow configuring the device to get the best performance/capacity of the link. Max 802.11n MCS index – choose the maximum rates to specify the modulation and coding scheme

(MCS) rates at which data can be transmitted between the access point and the client. If there will be an interference encountered, the device will step down to the highest rate that allows data transmission.

Max legacy data rate – choose the maximum data rate in Mbps at which device should transmit packets. It will attempt to transmit data at the highest data rate set. If there will be an interference encountered, the device will step down to the highest rate that allows data transmission.

AMSDU – enable the AMSDU packet aggregation. If enabled, the maximum size of the 802.11 MAC frames will be increased.

Short GI – enable short guard interval. If selected, then 400ns value will be used, else 800ns. Fragmentation – specify the Fragmentation threshold using slider or enter the value manually [256-

2346 bytes]. This is the maximum size for a packet before data is fragmented into multiple packets. Setting the Fragmentation threshold too low may result in poor network performance. Only minor modifications of this value are recommended.

deliberant Page 32

User’s Guide

RTS/CTS – specify the RTS threshold using slider or enter the value manually [0-2347 bytes]. The RTS threshold determines the packet size of a transmission and, through the use of an access point, helps control traffic flow.

Wireless Settings (Station)

Figure 18 - Wireless Settings

The wireless table allows configure main station parameters, such as SSID of the AP unit, Security, etc. Click on the edit icon and the wireless settings window will be displayed:

Figure 19 – Wireless AP Settings

SSID – specify the SSID of the wireless network device manually, or scan for iPoll 2 Access Points automatically:

deliberant Page 33

User’s Guide

For detailed information about security settings refer at the respective sections Wireless Security.

If auto scan for SSID is used, the results will be displayed in the Search SSID table, thus simply click on the required AP and SSID will be selected:

Advanced AP Settings

Quality of service (WMM) – enable to support quality of service for prioritizing traffic. Wireless VLAN ID – specify the VLAN ID for traffic tagging on particular radio interface. The Station

devices that associate using the particular SSID will be grouped into this VLAN.

Wireless Mode: Station (ARPNAT)

Use Wireless Configuration to setup radio interface of the device.

deliberant Page 34

User’s Guide

Figure 20 – Station Wireless Settings

Enable radio – use slide to enable or disable APC radio. Operating country - displays APC unit operating country. The Country selection determines the

IEEE mode – specify the wireless network mode. Tx power (dBm) – set the unit’s transmitting power at which the device will transmit data. The larger

Channel width - The default channel bandwidth for 802.11 radio is 20MHz. The 802.11n allow channel bonding in such way the total channel width becomes 40MHz.

Advanced Radio Settings

Advanced parameters allow configuring the device to get the best performance/capacity of the link.

deliberant Page 35

User’s Guide

Max 802.11n MCS index – choose the maximum rates to specify the modulation and coding scheme (MCS) rates at which data can be transmitted between the access point and the client. If there will be an interference encountered, the device will step down to the highest rate that allows data transmission.

AMSDU – enable the AMSDU packet aggregation. If enabled, the maximum size of the 802.11 MAC frames will be increased.

Short GI – enable short guard interval. If selected, then 400ns value will be used, else 800ns. Fragmentation – specify the Fragmentation threshold using slider or enter the value manually [256-

Wireless Settings (Station)

Figure 21 - Wireless Settings

The wireless table allows configure main station parameters, such as SSID of the AP unit, Security, etc. Click on the edit icon and the wireless settings window will be displayed:

deliberant Page 36

User’s Guide

Figure 22 – Wireless Station Settings

SSID – specify the SSID of the wireless network device manually, or scan for iPoll 2 Access Points automatically:

If auto scan for SSID is used, the results will be displayed in the Search SSID table, thus simply click on the required AP and SSID will be selected:

deliberant Page 37

User’s Guide

For detailed information about security settings refer at the respective sections Wireless Security.

Advanced AP Settings

Quality of service (WMM) – enable to support quality of service for prioritizing traffic. Wireless VLAN ID – specify the VLAN ID for traffic tagging on particular radio interface. The Station

devices that associate using the particular SSID will be grouped into this VLAN.

deliberant Page 38

User’s Guide

Security method

Access Point (autoWDS)

Access Point (iPoll 2)

Station

(WDS/iPoll 2)

Station (ARPNAT)

Open

× × ×

WEP 64bit/128bit

Personal WPA/WPA2

× × ×

Enterprise WPA/WPA2

× × ×

Wireless Security

If APC acts as an Access Point (auto WDS) or Access Point (iPoll 2) the wireless security settings will be used by the wireless stations for association. Thus wireless station security settings must conform the settings configured on the AP that station is associated with.

The APC supports various authentication/encryption methods:

 Open – no encryption.  WEP – encrypts the data portion of each packet exchanged on a wireless network using a 64-bit

or 128-bit WEP encryption key.

 Personal WPA/WPA2 – authorizes and identifies clients based on a secret key that changes

automatically at regular intervals.

 Enterprise WPA/WPA2 – RADIUS server based authentication (requires configured RADIUS

server).

Available security methods, according APC operating wireless mode is listed in the table below:

Open

By default there is no encryption enabled on the APC device:

Figure 23 – Wireless Security: Open with RADIUS MAC Authentication Enabled

WEP Encryption

WEP encryption can be either 64bit or 128bit.Select the required one and enter the rest parameters:

deliberant Page 39

User’s Guide

Figure 24 –Wireless Security: WEP Security

Key index - select the WEP key index [1-4]. Each number represents one of the four static keys of WEP. The selected key index will be used for frame encryption and decryption.

Key – specify the passkey, for the chosen WEP security:  For WEP 64bit encryption – 5 HEX pairs (e.g. aa:bb:cc:dd:ee), or 5 ASCII characters (e.g.

abcde);

 For WEP 128bit encryption – 13 HEX pairs (e.g. aa:bb:cc:dd:ee:ff:gg:hh:00:11:22:33:44), or 13

ASCII characters (e.g. abcdefghijklm);

WPA/WPA2 Personal

To setup WPA/WPA2 Personal encryption, need to select appropriate security type and specify the passphrase:

Figure 25 –Wireless Security: Personal WPA/WPA2 Security

Passphrase – specify WPA or WPA2 passphrase [8-63 characters].

WPA/WPA2 Enterprise for Access Points

APC has possibility to configure WPA/WPA2 Enterprise encryption with RADIUS authentication. Properly configured AP will accept wireless stations requests and will send the information to configured RADIUS server for client authentication.

deliberant Page 40

User’s Guide

The properly configured RADIUS server is required for WPA/WPA2 Enterprise encryption.

Figure 26 –Wireless Security: Enterprise WPA/WPA2 Security for AP

Auth. server IP/Port – specify the IP address and the port of the authentication RADIUS server where the authentication requests will be send to.

Auth. server key – enter the key for the authentication on specified RADIUS server. Accounting server – use slide to enable accounting RADIUS server, if required. Acc. server IP/Port – specify the IP address and the port of the accounting RADIUS server where

the accounting stats will be send to. Acc. server key – enter the key for the authentication on specified accounting RADIUS server.

WPA/WPA2 Enterprise for Stations

If APC is operating in Station wireless mode, Station will send requests to AP, which will redirect authentication parameters to required RADIUS server.

deliberant Page 41

User’s Guide

Identity and Password on the Station must match the identity and password running on the RADIUS server's user list.

Wireless ACL is active only in Access Point (auto WDS) and Access Point (iPoll 2) wireless modes.

Figure 27 –Wireless Security: Enterprise WPA/WPA2 Security for Stations

EAP method – choose EAP method:

 EAP-TTLS  PEAP

Identity – specify the identity of the authentication to the RADIUS server. Password – specify the password of the authentication to the RADIUS server.

Wireless ACL

Access Control provides the ability to limit associations wirelessly, based on MAC address, to an AP by creating an Access Control List (ACL) on each wireless interface (including VAPs).

Figure 28 – Wireless ACL Configuration

deliberant Page 42

User’s Guide

MAC filter policy – define the policy:

 Open – no rules applied.  Allow MAC in the list – only listed MAC clients can connect to the AP (white list).  Deny MAC in the list – only listed MAC clients can NOT connect to the AP (black list).

To add new rule, press the Add button.

To remove the rule, click the delete icon next to required record. To edit the rule, click the pencil icon next to required record.

deliberant Page 43

User’s Guide

Services Configuration

Use Services menu is divided into further five sections:

 Date & time  Remote management  SNMP  Ping watchdog  WNMS

Figure 29 - Services Menu

Date & time

Use this section to manage the system time and date on the device automatically, using the Network Time Protocol (NTP), or manually, by setting the time and date on the device.

The NTP (Network Time Protocol) client synchronizes the clock of the device with the defined time server. Choose NTP from the configuration menu, select your location time zone and enter NTP server in order to use the NTP service.

Figure 30 – Date&time: NTP Configuration

Enable NTP – select this option as enabled to configure NTP.

deliberant Page 44

User’s Guide

Timezone – select the timezone. Time zone should be specified as a difference between local time and GMT time.

NTP server – specify the trusted NTP server IP or hostname for time synchronization. Test NTP servers - click this button to check if the specified servers responses successfully.

To adjust the clock settings manually, disable NTP option and specify the following settings:

Figure 31 – Date&time: Manual Configuration

Enable NTP – disable this option to set date&time manually. Timezone – select the timezone. Time zone should be specified as a difference between local time

and UTC time.

Date – specify the new date value in format DD/MM/YYYY Time – specify the time in format HH:MM.

Remote Management

Use this menu to manage access to the APC via SSH and Telnet:

Figure 32 – Remote Management Configuration

Enable SSH – enable or disable SSH access to device. SSH port – specify the SSH service port. By default SSH port is 22. Enable telnet – enable or disable telnet access to device. Telnet port – specify the telnet port. By default SSH port is 23.

deliberant Page 45

User’s Guide

SNMP

SNMP is the standard protocol that is widely used for remote network management over the Internet. With the SNMP service enabled, the device will act as SNMP agent.

Figure 33 – SNMP Service Settings

Enable SNMP – specify the SNMP service status. R/O community – specify the read-only community name for SNMP version 1 and version 2c. The

read-only community allows an APC unit manager to read values, but denies any attempt to change values.

Ping watchdog

Enable Ping Watchdog for continuous monitoring of the APC unit network connection with the specified trusted host. If enabled, the APC unit will send Ping requests periodically to the host and in case there is no response within a specified time period, the Ping Watchdog will reboot the APC unit.

Figure 34 –Ping Watchdog

Enable ping watchdog – click to enable Ping Watchdog function. Host/IP address – specify the host where the Ping requests will be sent to. Test host/IP address - click this button to check if the specified host responses successfully. Ping interval - specify the interval, in minutes, between Ping requests. Ping fail count to reboot - specify the count of failed Ping replies. After specified count of Ping

failures, the APC unit will reboot itself automatically.

deliberant Page 46

User’s Guide

WNMS

Wireless Network Management System (WNMS) is a centralized monitoring and management system for wireless network devices. The communication between managed devices and the WNMS server is always initiated by an WNMS client service running on every device.

Enable WNMS agent – select to enable WNMS agent. Server/Collector URL – specify the URL of the WMS server to which that heartbeat notifications will

be sent to. Test connection - click this button to check if the specified server responses successfully.

System Configuration

System menu allows you to manage main APC settings and perform main system actions (reboot, restore configuration, etc.). The section is divided into further five sections:

 Device settings  System functions  User accounts  LED settings  Advanced settings

Friendly device name – specify name of the APC that will be used to identify the unit. Contact information – specify the name of the contact person, such as a network administrator, for

the APC.

Device location – describe the location of the device. Longitude – specify the longitude coordinates of the device [specific decimal format, e.q. 54.869446]. Latitude – specify the latitude coordinates of the device [specific decimal format, e.q. 23.891058].

Both coordinates helps indicate accurate location of the device.

deliberant Page 47

User’s Guide

Resetting the device is an irreversible process. Current configuration and the administrator password will be set back to the factory default.

For security reasons it is recommended to change the default administrator username and password as soon as possible.

Default administrator logon settings are: Username: admin Password: admin01

System functions

Figure 35 - System Functions

New configuration will be effective after the Apply button is activated and system reboot cycle is completed. Previous system configuration is deleted after Apply button is activated. It is highly recommended to backup the system configuration before uploading the new configuration.

Restore configuration – click to upload an existing configuration file to the device. Reboot device – reboot device with the last saved configuration. Reset device to factory defaults – click to restore unit's factory configuration.

User accounts

Figure 36 – User Accounts

Click Edit button next to user for changing credentials:

deliberant Page 48

User’s Guide

The only way to gain access to the web management if you forget the administrator password is to reset the unit to factory default settings.

Device discovery function is available only on Station (WDS/iPoll2) and Station (ARPNAT) wireless modes.

Figure 37 – User Account Settings

Username – change the administrator’s username. Old password – enter the old administrator password. New password – enter the new administrator password for user authentication. Verify password – re-enter the new password to verify its accuracy.

LED settings

The APC has possibility to control LEDs:

Figure 38 – Device LED Control

LED status – use the slide to disable or enable LED signals.

Advanced settings

Enable this feature to allow the APC unit discovery within reach of a single multicast packet.

deliberant Page 49

User’s Guide

The device system firmware upgrade is compatible with all configuration settings. When

the device is upgraded with a newer version or the same version builds, all the system’s

configuration will be preserved after the upgrade.

Figure 39 – Device discovery

Device discovery – select to enable APC discovery function.

Firmware Upgrade

The current version of the device firmware is shown on the upper left corner of the Web interface.

Figure 40 – Firmware Version

Click the (Update) link near the running firmware name and select the proper firmware image in the Firmware Update pop-up window, then click Upload button:

Figure 41 – Firmware Upload

The new firmware image is uploaded to the controller’s temporary memory. It is necessary to save the firmware into the device permanent memory. Click the Upload button:

deliberant Page 50

User’s Guide

Do not switch off and do not disconnect the device from the power supply during the firmware upgrade process as the device could be damaged.

Figure 42 –Firmware Upgrade

Current version – displays version of the current firmware. Uploaded version – displays version of the uploaded firmware. Upgrade – upgrade device with the uploaded image and reboot the system.

deliberant Page 51

User’s Guide

Tools

Antenna Alignment

The Antenna Alignment tool measures signal quality between the Station and AP. For best results during the antenna alignment test, turn off all wireless networking devices within range of the device except the device(s) with which you are trying to align the antenna. Watch the constantly updated display as you adjust the antenna.

Figure 43 – Antenna Alignment

Start – press this button to start antenna alignment. Stop – press this button to stop antenna alignment. Averaging – if this option enabled, the graph will display the average Signal Strength of both

antennas.

deliberant Page 52

User’s Guide

It is recommended to ensure that there is no traffic on the link before running the Link Test as results may not be completely accurate.

Site Survey

The Site Survey tool shows overview information for wireless networks in a local geographic area. Using this test, an administrator can scan for working wireless devices, check their operating channels, encryption and see signal/noise levels.

To perform the Site Survey test currently, click the Start scan:

Last updated – displays when the last scan was performed.

Link Test

Use the Link test tool to check the quality of the established iPoll 2 link. This tool tests the throughput at selected packet sizes and iterations.

Figure 44 – Linktest Results

Packet size - select packet sizes in bytes at which the test will be performed.

deliberant Page 53

User’s Guide

Iterations - select number of test iterations. iPoll 2 Access Point – displays the Access Point information (iPoll 2 station side).

iPoll 2 station – select the Station the Link Test will be performed with (iPoll 2 Access Point side).

Traffic direction – select the traffic direction for the performing test. Start – click to start the throughput test. Stop – click to stop the throughput test.

Support

Troubleshooting

The troubleshooting file contains valuable information about device configuration, routes, log files, command outputs, etc. When using the troubleshooting file, the device quickly gathers troubleshooting information automatically, rather than requiring you to gather each piece of information manually. This is helpful for submitting problems to the support team.

Figure 45 – Troubleshooting File Download

Download– click to download the troubleshooting file. This may take a few minutes to gather information and to complete download.

deliberant Page 54

User’s Guide

System Log

The system log viewer utility provides debug information about the system services and protocols. If the device's malfunction occurs recorded messages can help operators to locate misconfiguration and system errors.

Click the refresh icon, on the upper right corner, to view current system messages.

Antennas:

Only below approved antennas can be used for this modular installation: Type1: Manufacture: ExtraLink, Model: 2400A-12, Gain: 12dBi, Number: 2

Type2: Manufacture: Shenzhen fengliyuan, Model: FS-2400F, Gain: 3dBi, Number: 2

deliberant Page 55

LigoWave NFT1NI User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual