Lightwave LW830WH User Manual

connect

Inline Relay

Operation Manual

Model No: JSJS LW830

It is important to install this product in accordance
with the tting instructions below. Failure to do so
may render your guarantee void.

IMPORTANT: PLEASE RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE AND FOR GUIDANCE ON
THE ASSOCIATION OF REMOTE HANDSETS. FOR
HELP AND SETUP GUIDANCE PLEASE VISIT
www.lightwaverf.com

OVERVIEW:

Manual Button/
LED Indicator

Time Delay Switch

Cable Cover

Cable Clamp

The Inline Relay is designed to switch mains rated
resistive loads and is rated at up to 3000w. It is mains
powered and includes a built-in time delay switch.
The relay can be operated using any LightwaveRF
Connect Remote or other transmitter.

FITTING AND WIRING INSTRUCTIONS:

Important Things to Consider Before you Begin

1). Before commencing work, ALWAYS isolate the
mains power supply and remove the fuse in the fuse
box or switch o the circuit breaker in the consumer
unit.

2). If unit is to be used as a replacement for an existing
product, remove existing unit from its location and
disconnect the wiring.

3). Connect the wires as shown in appropriate wiring
diagrams. Use green/yellow sleeving on any earth
conductors not insulated. Ensure terminals are
properly tightened and no bare wire is visible. When
mounting products into mounting boxes make sure
conductors are not trapped.

4). Products must be installed in accordance with the
latest building and IEE wiring regulations. If in any
doubt, please contact a qualied electrician.

INSTALLATION:

Switched Live &
Neutral OUT

Resistive Load
(e.g. bulb)
Max 3000w

Earth in/out
Terminals

Live & Neutral IN

Installing the Inline Relay

1) Switch o the mains power

2) Connect the incoming Live and Neutral wires from
the 230v mains circuit to the live and neutral
terminals as shown in the diagram (incoming wires
marked L & N).

3) Connect the incoming earth wire to one of the
earth terminals indicated on the diagram. There are
two terminals to accommodate an incoming AND an
outgoing earth if required.

4) Connect the swtiched live and outgoing neutral
wire connected to the switched circuit to the
corresponding terminals as shown in the diagram.

IMPORTANT: Remember that the maximum loading
for the Relay is 3000w (resistive load). Exceeding this
limit could cause damage to the device.

SETUP:

IMPORTANT: Make sure that the relay is accessible
once installed in order to operate the maunal
button for pairing.

Pairing with a LightwaveRF transmitter

1) Press and hold the manual button on the Inline
Relay until the LED starts to ash.

Manual button

2) Press the ‘on’ or ‘up’ button on the transmitter. The
LED will ash quickly for 2 seconds to indicate a
successful pairing.

NOTE: The Inline Relay can be paired with up to 6
separate transmitters at any one time.

Unpairing with a LIghtwaveRF transmitter

1) Press and hold the manual button on the Inline
Relay until the LED starts to ash.

2) Press the ‘o’ or ‘down’ button on the transmitter
(the LED will ash quickly for 2 seconds to indicate a
successful unpairing of that device).

Complete Memory Reset

1) Press and hold the manual button. Release the
button once the LED begins to ash. Press and hold a
second time until the LED ashes more quickly.

2) Press (don't hold) the manual button a third time.
The LED will ash quickly for 2 seconds to indicate
that the memory has been cleared.

Setting the timer

The Inline Relay has an automatic time delay function
built-in. This oers 8 separate time delays ranging
from 3 seconds to 8 hours. After being turned on,
once the allotted time has elapsed, the relay will
automatically turn o.

Setting:

‘0’ : No timer set (default standard on/o operation).

‘3s’: Automatically turn o after 3 seconds.

‘30s’: Automatically turn o after 30 seconds.

‘1m’: Automatically turn o after 1 minute.

‘10m’: Automatically turn o after 10 minute.

‘2h’: Automatically turn o after 2 hours.

‘4h’: Automatically turn o after 4 hours.

‘8h’: Automatically turn on/o after 8 hours.

Additional independent time delays can also be set
using the ‘timer’ function on the LightwaveRF
Smartphone app (requires the LightwaveRF Wi-Link).

OPERATION:

1) Press the ‘on’ button on the transmitter to turn the
circuit on.

2) Press the ‘o’ button on the transmitter to turn the
circuit o.

3) Press the Manual button to toggle the Relay on/o
Manually.

NOTE: If the RF range between the transmitter and
receiver is too great to achieve reliable operation, the
LightwaveRF SIGNAL BOOSTER may be used in
conjunction with this product to increase the signal
strength over greater distances.

SPECIFICATION:

Radio frequency: 433.92 MHz
Input: 230V~ / 50Hz
Output: max. 3000 watts for resistive load
Operating distance: 30 meter closed eld.
Standby power consumption: ≦ 1w.

Birmingham Science Park Aston

Faraday Wharf

Holt Street

Birmingham

B7 4BB

Tel: [phone]

Email: [e-mail]