Lightronics WSRXF User Manual
Page 1 of 3
WSRFX WIRELESS DMX RECEIVER
Version 0.0 OWNERS MANUAL 07/16/2009
DESCRIPTION
The WSRFX is a compact RF receiver unit which can
receive a USITT DMX-512 lighting control signal
from a compatible wireless DMX transmitter or
wireless equipped DMX lighting console. The received
DMX signal is available on a standard DMX 5 pin
Female XLR connector for a connection to a normal
wired DMX system. The WSRFX is supplied with a
UL listed external power supply and an antenna.
The WSRFX operates with a single specific compatible
wireless DMX transmitter or console at a time.
Receiver units get the same information they would get
using a cable connected to a DMX lighting console.
Multiple WSRXF receivers may be operated with a
single transmitter or console.
The wireless system uses the 2.45 GHz band and
operates at low power (< 100mW). The operating
range is approximately 1400 ft. indoors and about 4000
ft. for outdoor operation. This range could vary
significantly depending on the surrounding conditions.
A link between one or more WSRFX receivers and one
compatible transmitter unit is invoked to enable
wireless operation. The linking operation is performed
at the transmitter. Once linked, the receiving units can
operate ONLY with that specific transmitter. The link
is retained even when the receiver and/or transmitter
are powered off. Receiver units may be released from
the link either at the transmitter or at the receiver. If
released at the transmitter then ALL linked receivers
will be released. If unlinked at the receiver then
ONLY that receiver will be released.
INSTALLATION
POWER CONNECTION
The WSRFX is powered by an external 120VAC
power supply which provides 13VAC at 700mA to the
unit. It can be powered by another source if it meets
the requirements marked on the WSRFX. The power
connector on the unit is a 2.1mm male plug.
Connect the main body of the power supply to any
convenient 120VAC outlet. Then connect the 2.1mm
plug to the WSRFX.
ANTENNA CONNECTION
Carefully thread the antenna on the gold antenna
connector on one end of the unit. It should be finger
tight only. The connectors can be damaged or jammed
if too tight. The antenna will swivel to a convenient
orientation while connected.
DMX OUTPUT CONNECTION
Connect the DMX signal cable to the 5 Pin Female
XLR connector on the end of the WSRFX.
Connect the other end of the cable to a normal DMX
Dimmer or dimmer chain.
DMX CONNECTOR
PIN NUMBER
1 DMX COMMON
2 DMX DATA 3 DMX DATA +
4 NOT USED
5 NOT USED
SIGNAL NAME
OPERATION
LINK CONTROL BUTTON
This pushbutton switch is used to release the link with
its current transmitter.
STATUS INDICATOR LED
The indicator shows the status of the unit as follows:
OFF………………NO POWER OR NOT LINKED
SLOW FLASH…..NO DMX
FAST FLASH……LINKING IN PROGRESS
ON………………..LINKED and RECEIVING DMX
LINKING RECEIVERS
Links are always performed at the transmitter. Links
will not be established with receivers already linked to
another transmitter device.
You should begin by unlinking the receiver at the
receiver itself since it could be linked to a transmitter
other than the one you have.
www.lightronics.com
Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
W
Page 2 of 3
WSRFX WIRELESS DMX RECEIVER
Version 0.0 OWNERS MANUAL 07/16/2009
At the transmitter - Push the link control button once
(do not hold down). The indicator LED will go to fast
flash for about 10 seconds. It will then go to an ON
state.
The link indicator on the WSRXF receiver will also go
to fast flash and may continue this for several more
seconds after the transmitters indicator goes to ON.
The link indicator on the receiver will go to an ON
state when the link is stable.
UNLINKING A SINGLE RECEIVER
At the receiver - Hold the link control button down for
about 5 seconds.
The receiver indicator LED will go OFF showing that
no link is active.
UNLINKING ALL RECEIVERS AT THE
TRANSMITTER
At the transmitter - Hold down the link control button
down for about 5 seconds.
The transmitter indicator LED will go to slow flash
showing that no links are active.
The receiver unit(s) status indicator will go OFF.
Note that receivers linked to a different transmitter will
not be released.
MAINTENANCE AND REPAIR
OWNER MAINTENANCE
There are no user serviceable parts in the unit. Service
by other than Lightronics authorized agents will void
your warranty.
CLEANING
The unit exterior may be cleaned using a soft cloth
dampened with a mild detergent/water mixture.
DO NOT IMMERSE the unit in any liquid or allow
liquid to get into the controls. DO NOT USE any
solvent based or abrasive cleaners on the unit.
OPERATING AND MAINTENANCE ASSISTANCE
Dealer and Lightronics Factory personnel can help you
with operation or maintenance problems. Please read
the applicable parts of this manual before calling for
assistance.
If service is required - contact the dealer from whom
you purchased the unit or contact Lightronics, Service
Dept., 509 Central Drive, Virginia Beach, VA 23454
TEL: (757) 486-3588.
FRONT VIEW
HOLD > 5 SEC.
TO RELEASE LINK
LINK CONTROL
BUTTON
DMX OUT
ANTENNA
CONNECTOR
REAR VIE
POWER
5 PIN FEMALE
XLR CONNECTOR
LED ON SOLID
LINK + DMX OK
LED SLO FLASH
LINKED - NO DMX
LED FAST FLASH
LINK IN PROGRESS
STATUS
INDICATOR
LED
Wireless DMX Rece ive r
WSRXF
8 15VAC
700mA
www.lightronics.com
Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Loading...