How it Works
Lightronics
Loading...
FXLE1260W
User Manual
4 pgs124.89 Kb0

Lightronics FXLE1260W User Manual

Download
Page 1 of 4 FXLE1260W LED FIXTURE
Version 0.1 OWNERS MANUAL 07/24/2013
FEATURES AND SPECIFICATIONS
DESCRIPTION
The FXLE1260W is a LED ellipsoidal fixture suitable for stage, disco, night club, and other artistic applications. It has automatic stand alone control modes and can operate via a DMX-512 external signal.
A mounting yoke enables the fixture to be operated in various positions and orientation.
INSTALLATION
LOCATION
The FXLE1260W is rated IP20 and is intended for
INDOOR USE ONLY.
Locate the unit in a well ventilated area away from moisture and heat. Maintain a minimum spacing of 20" between the unit and other objects. The maximum ambient operating temperature is 45
º
C (113ºF). Keep the vent holes clear. Holes are provided on the yokes to install a lighting bar pipe clamp. Use a safety cable when hanging the fixture.
POWER CONNECTIONS
The FXLE1260W has a line cord for connection to a 120 VAC, 15 Amp, 60Hz, grounded service. Do not try to power the unit from a dimmer pack.
RISK OF ELECTRIC SHOCK
DANGER
The safety ground pin on the power cord must be used.
DMX CONNECTIONS
A system using DMX control should be connected as a chain of devices. In other words the control signal cable should proceed from the controller to the first receiving device and then to others in a continuous "daisy chain" fashion.
The FXLE1260W has a DMX IN and a DMX OUT connector to be used to connect the chain. The control cable should NOT be split into a multiple run star arrangement with a cable running from the controller directly to each receiving device.
DMX CONNECTOR PIN ASSIGNMENTS
There are two different connectors which can be used for DMX control. They are both XLR type connectors. Some units use 3 pin connectors. Others use 5 pin connectors. The FXLE1260W receives a DMX signal on the 3 pin MALE connector on the rear of the unit. The 3 pin FEMALE connector is used to connect to the next DMX device on the control chain.
If your console uses a 5 pin XLR connector you can make up an adapter cable to accommodate this. The table below shows the pin assignments for both 3 pin and 5 pin XLR connectors.
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 2 of 4 FXLE1260W LED FIXTURE
Version 0.1 OWNERS MANUAL 07/24/2013
PIN # SIGNAL NAME
1 DMX COMMON 2 DMX DATA ­3 DMX DATA + 4 NOT USED 5 NOT USED
DMX TERMINATION
A DMX chain should be terminated at the last receiving device on the chain. This is done by installing a commonly available 1/4 Watt, 120 Ohm resistor across the DATA - and DATA + wires at the last device. If you have only a few fixtures very close together and a very short run to the controller then you may be able to operate without the terminator.
OPERATION
A power ON/OFF switch is located at the rear of the unit. A control panel on the back of the unit is used to set the operating options. It consists of an LED display and four buttons
(ESC, ENTER, DOWN, and UP).
CONTROL PANEL
ESC
ENTER
DOWN
UP
Use
UP
and
Push
ENTER
DOWN
when you reach the option you want to
to scroll the available choices.
check or set. The current setting for the option will be shown. Use Push
ENTER
UP
and
DOWN
to change the setting.
to invoke the new setting. Use
ESC
to
exit from the sub menus.
DMX OPERATION
Use the address. The range is
A - - -
menu to set the unit DMX starting
r001 - r511.
NOTE
The current version of the FXLE1260W will not respond to DMX addresses above 255 even though the addressing menu allows selections up to 511.
The fixture uses two DMX channels allocated as follows:
CHANNEL 1: Fixture Intensity (000 - 255) CHANNEL 2: Strobe Control (000 - 255) 000 is Strobe OFF
DEMO MODE (dEnO)
The
DEMO
SC00 SC01 SC02 SC03
mode has 4 choices as follows:
External DMX control Slow fade ON/OFF (stand alone operation) Strobe effects (stand alone operation) ON/OFF sequence (stand alone operation)
SC00 must be used when operating with an external DMX controller.
If the unit was switched to another must be returned to
SC00
and then a RESET (rESt)
DEMO
mode then it
must be done.
NAST MODE
This function is not currently supported.
RESET (rESt)
The reset function enables DMX operation after stand alone operation.
Push show
ENTER
OFF
when
rESt
is shown. The display will
. Push UP to execute the reset. The display
will revert to show the DMX starting address.
MAINTENANCE AND REPAIR
DANGER DO NOT OPEN UNI T
RISK OF ELECTRIC SHOCK
RISK OF FIRE
TROUBLESHOOTING
Check that you have power applied to the unit. Check the DMX control cable. Check the address settings of the unit and controller.
CLEANING DISCONNECT THE POWER CORD BEFORE
HANDLING THE UNIT.
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 3 of 4 FXLE1260W LED FIXTURE Version 0.1 OWNERS MANUAL 07/24/2013
Do not use chemicals or solvents when cleaning the fixture. A mild detergent can be used sparingly if needed. Ensure that the unit is dry before re-u
REPAIR
se.
The only FXLE1260W user serviceable part is a 5 mm x 20 mm externally accessible fuse on the rear panel.
DISCONNECT THE POWER CORD BEFORE CHECKING OR REPLACING THE FUSE.
Replace fuse ONLY with 3.15 Amp, 250VAC, fast acting fuse.
Internal service on the unit by other than Lightronics authorized agents will void the warranty.
If service is required, contact the dealer from whom you purchased the item, or contact the Lightronics, Service Department, 509 Central Drive, Virginia Beach, VA 23454. Tel: 757 486 3588.
PHOTOMETRIC CHARACTERISTICS
ILLUMINATION (LUX)
Beam Angle
19 deg -- 2500 1214 26 deg -- 1723 628 36 deg -- 1200 516 50 deg 2160 635 --
BEAM DIAMETER (METERS)
Beam Angle
19 deg -- 7 ft 11 ft 26 deg -- 10 ft 16 ft 36 deg -- 14 ft 20 ft 50 deg 10 ft 16 ft --
Distance From Fixture
10 feet 20 feet 30 feet
Distance From Fixture
10 feet 20 feet 30 feet
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Y
This product is warranted for a period of TWO YEARS from the date of purchase against defects in materials and workmanship.
This warranty is subject to the following restrictions and conditions:
A) If service is required, you may be asked to provide proof of purchase from an authorized Lightronics dealer.
B) This warranty is valid only for the original purchaser of the unit. C) This warranty does not apply to damage resulting from abuse, misuse, accidents,
shipping, and repairs or modifications by anyone other than an authorized Lightronics service representative.
D) This warranty is void if the serial number is removed, altered or defaced. E) This warranty does not cover loss or damage, direct or indirect arising from the use or
inability to use this product. F) Lightronics reserves the right to make any changes, modifications, or updates as
deemed appropriate by Lightronics to products returned for service. Such changes may be made without prior notification to the user and without incurring any responsibility or liability for modifications or changes to equipment previously supplied. Lightronics is not responsible for supplying new equipment in accordance with any earlier specifications.
G) This warranty is the only warranty either expressed, implied, or statutory, upon which the equipment is purchased. No representatives, dealers or any of their agents are authorized to make any warranties, guarantees, or representations other than expressly stated herein.
H) This warranty does not cover the cost of shipping products to or from Lightronics for service.
I) Lightronics Inc. reserves the right to make changes as deemed necessary to this warranty without prior notification.
WARRANT
Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 20100211
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use