How it Works
Lightronics
Loading...
FXLD836C4I
User Manual
6 pgs348.97 Kb0

Lightronics FXLD836C4I User Manual

Download
Page 1 of 6 FXLD836C4I LED FIXTURE
Version 0.1 OWNERS MANUAL 06/06/2013
FEATURES AND SPECIFICATIONS
DESCRIPTION
The FXLD836C4I is a RGBW LED lighting fixture. It is suitable for stage, disco, night club, and other artistic applications. It has several stand alone control modes and can operate via a DMX-512 external signal.
A double yoke enables the fixture to be operated in several positions.
INSTALLATION
LOCATION
The FXLD836C4I is rated IP20 and is intended for
INDOOR USE ONLY.
Locate the unit in a well ventilated area away from moisture and heat. Keep the vent holes clear. Holes are provided on the yokes to install a lighting bar pipe clamp. Use a safety cable when hanging the fixture.
POWER CONNECTIONS
RISK OF ELECTRIC SHOCK
CAUTION
The FXLD836C4I has a blue powercon style connector for power input. A compatible power cable is provided for connection to a 120 VAC, 15 Amp, 60Hz, grounded service. Push the blue connector on the cable straight into the blue connector on the unit and twist aprox. 1/8 turn clockwise to latch it.
The white powercon style connector on the unit is used to pass power on to another unit. A mating white connector is also provided.
Caution is advised since the line cord is rated for aprox. 7 Amps maximum.
THE SAFETY GROUND TERMINAL ON ALL POWER CABLES MUST BE USED.
DMX CONNECTIONS
A system using DMX control should be connected as a chain of devices. In other words the control signal cable should proceed from the controller to the first receiving device and then to others in a continuous "daisy chain" fashion.
The fixture has a DMX IN and a DMX OUT connector to be used to connect the chain. The control cable should NOT be split into a multiple run star arrangement with a cable running from the controller directly to each receiving device pack.
DMX CONNECTOR PIN ASSIGNMENTS
There are two different connectors which can be used for DMX control. They are both XLR type connectors. Some units use 3 pin connectors. Others use 5 pin connectors. The FXLD836C4I receives a DMX signal on the 3 pin MALE connector on one side of the unit. The 3 pin FEMALE connector is used to connect the next DMX device on the control chain.
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 2 of 6 FXLD836C4I LED FIXTURE Version 0.1 OWNERS MANUAL 06/06/2013
If your console uses a 5 pin connector you can make up an adapter cable to accommodate this. The table below shows the pin assignments for BOTH the 3 pin and 5 pin connectors.
DMX TERMINATION
PIN # SIGNAL NAME
1 DMX COMMON 2 DMX DATA ­3 DMX DATA + 4 NOT USED 5 NOT USED
A DMX chain should be terminated at the last receiving device on the chain. This is done by installing a commonly available 1/4 Watt, 120 Ohm resistor across the DATA - and DATA + wires at the last device. If you have only a few fixtures very close together and a very short run to the controller then you may be able to operate without the terminator.
OPERATION
A control panel on one side of the unit is used to set the operating options. It consists of an LED display and four buttons
(MENU, UP, DOWN, and ENTER)
CONTROL PANEL
Push
UP
MENU UP DOWN ENTER
MENU
to access the operating options. Then use
and
DOWN
to scroll through the available choices. When you reach the option you want to set or change ­push
ENTER
for the option and/or change it. Push
. Now you can view the current setting
ENTER
to save your changes and activate the option. See the "MENU NAVIGATION" diagram for additional details.
There are 9 operation modes: DMX, Red Level, Green Level, Blue Level, White Level, Strobe, Fade, Auto Sequence, and Auto Run.
DMX OPERATION
Use the Addr menu to set the starting address of the unit. You can set the starting address of the unit with the UP and DOWN buttons.
For DMX operation the FXLD836C4I fixture can be configured as a 4 channel, 5 channel, or 7 channel unit.
Set the CH - - menu to A001(4 channel), P001 (5 channel), or F001(7 channel) operation.
Detailed information on DMX channel operation is given in the tables
MANUAL OPERATION
DMX VALUES AND FUNCTIONS
.
For manual operation the red, green blue, and white LED intensity levels may be independently set. Use the rL - -, gL - -, bL - -, and EL - -, menus to set the levels. The range is from 00 to 100. 00 is OFF.
STROBE MODE (
FLAS
)
The Strobe mode causes the unit to flash all led's. The speed is user controllable by using the FLAS menu. The speed range is 1 - 100. 100 is fastest.
AUTO FADE (
FAdE
)
The Auto Fade mode cycles smoothly through a sequence of seven colors. Use the FADE menu to set the speed and activate the option. The range is from 0 to 100. 100 is fastest.
AUTO SEQUENCE (
ASC -
)
The AUTO SEQUENCE mode switches continuously through a sequence of colors. Use the ASC - menu to set the sequence speed. The range is from 1 to 100. 100 is fastest.
AUTO RUN (
Auto
)
The unit can operate using 100 preset programs. Programs 0 thru 49 are a variety of colors and patterns.
Programs 50 thru 100 are similar but are sound synced to music base notes.
Use the Auto menu to select and activate a preset autorun program.
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 3 of 6 FXLD836C4I LED FIXTURE
Version 0.1 OWNERS MANUAL 06/06/2013
MAINTENANCE AND REPAIR
TROUBLESHOOTING
CAUTION DO NOT OPEN UNIT
RISK OF ELECTRIC SHOCK
RISK OF FIRE
Check that you have power applied to the unit. Check the DMX control cable. Check the address settings of the unit and the
controller.
CLEANING
Do not use harsh chemicals or solvents when cleaning the fixture. A mild detergent can be used sparingly if needed. Ensure that the unit is completely dry before re-use.
REPAIR
The fixture contains a 2 Amp, fast acting, 5mm x 20mm externally accessible fuse. Replace the fuse ONLY with the same size and type.
The FXLD836C4I does not contain any other user serviceable parts. Internal service on the unit by other than Lightronics authorized agents will void the warranty.
If service is required, contact the dealer from whom you purchased the item, or contact the Lightronics, Service Department, 509 Central Drive, Virginia Beach, VA 23454. Tel: 757 486 3588.
PHOTOMETRIC CHARACTERISTICS
Distance Illuminance Beam Diam. (ft) (Lux) (ft)
10 3330 4 20 1025 6 30 475 8
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 4 of 6 FXLD836C4I LED FIXTURE
Version 0.1 OWNERS MANUAL 06/06/2013
MENU NAVIGATION
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 5 of 6 FXLD836C4I LED FIXTURE
Version 0.1 OWNERS MANUAL 06/06/2013
DMX VALUES AND FUNCTIONS
4 CHANNEL MODE (MODE A)
CHANNEL NO. FUNCTION
1 0 - 255 Red Level 2 0 - 255 Green Level 3 0 - 255 Blue Level 4 0 - 255 White Level
5 CHANNEL MODE (MODE P)
CHANNEL NO. FUNCTION
1 0 - 152 RGB Dimmer Master
197 - 242 Auto Strobe (slow - fast)
243 - 255 RGB Dimmer Master 2 0 - 255 Red Level 3 0 - 255 Green Level 4 0 - 255 Blue Level 5 0 - 255 White Level
153 - 196 Strobe (slow - fast)
7 CHANNEL MODE (MODE F)
CHANNEL NO. FUNCTION
1 0 - 255 Red Level 2 0 - 255 Green Level 3 0 - 255 Blue Level 4 0 - 255 White Level 5 0 - 1 No Strobe
197 - 255 Auto Strobe (slow - fast)
6 0 - 1 No Function
20 - 39 Color Sequence (slow - fast) 40 - 59 Color Pattern (slow - fast) 60 - 79 Yellow 80 - 99 Purple 100 - 119 Light Green 120 - 139 Orange 140 - 159 Red On/Off (10 sec.) 160 - 179 Green On/Off (10 sec.) 180 - 199 Blue On/Off (10 sec.) 200 - 219 Yellow On/Off (10 sec.) 220 - 229 Cyan On/Off (10 sec.) 230 - 249 White On/Off (10 sec.) 250 - 255 All On
7 0 - 255 Dimmer (All Off - All On)
2 - 196 Strobe (slow - fast)
2 - 19 Color Fade (slow - fast)
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Y
This product is warranted for a period of TWO YEARS from the date of purchase against defects in materials and workmanship.
This warranty is subject to the following restrictions and conditions:
A) If service is required, you may be asked to provide proof of purchase from an authorized Lightronics dealer.
B) This warranty is valid only for the original purchaser of the unit. C) This warranty does not apply to damage resulting from abuse, misuse, accidents,
shipping, and repairs or modifications by anyone other than an authorized Lightronics service representative.
D) This warranty is void if the serial number is removed, altered or defaced. E) This warranty does not cover loss or damage, direct or indirect arising from the use or
inability to use this product. F) Lightronics reserves the right to make any changes, modifications, or updates as
deemed appropriate by Lightronics to products returned for service. Such changes may be made without prior notification to the user and without incurring any responsibility or liability for modifications or changes to equipment previously supplied. Lightronics is not responsible for supplying new equipment in accordance with any earlier specifications.
G) This warranty is the only warranty either expressed, implied, or statutory, upon which the equipment is purchased. No representatives, dealers or any of their agents are authorized to make any warranties, guarantees, or representations other than expressly stated herein.
H) This warranty does not cover the cost of shipping products to or from Lightronics for service.
I) Lightronics Inc. reserves the right to make changes as deemed necessary to this warranty without prior notification.
WARRANT
Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 20100211
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use